Commit Graph

170 Commits

Author SHA1 Message Date
Shiji Yang
2e6d19ee32 ramips: fix wifi mac address of HiWiFi series devices
For HiWiFi series devices, label_mac can be read from bdinfo partition,
and lan_mac, wlan2g_mac are same as the label_mac. Converting label_mac
to wlan5g_mac only needs to unset 6th bit. (It seems that all HiWiFi's
label_mac start with D4:EE)

For example:
label	D4:EE:07:32:84:88
lan	D4:EE:07:32:84:88
wan	D4:EE:07:32:84:89
wlan2g	D4:EE:07:32:84:88
wlan5g	D0:EE:07:32:84:88

Tested on HiWiFi HC5661.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-03-26 02:02:44 +01:00
Rodolphe de Saint Léger
46c5de5385 ramips: add support for Netgear WN3100RPv2
This patch adds support for the Netgear WN3100RPv2
http://www.netgear.com/support/product/wn3100rpv2.aspx

Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Stock firmware based on OpenWRT Kamikaze

Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577

This device seems to be same hardware as a WN3000RPv3

Flash instructions:
- Use the Netgear WebUI to upgrade to OpenWRT using the factory image
  (see note below),
- Use the sysupgrade image for upgrading versions from OpenWRT,
- TFTP recovery procedure can be used to flash the factory image
  (preferred method).

Note:
- The WebUI may not reboot automatically, wait at least 5 minutes before
  powercycling the device

Flashing using TFTP:
- Set you IP address to 192.168.1.10/24 (no gateway)
- Connect your machine to the Ethernet port
- Power off the device and wait for 10 seconds,
- Hold the reset button and power on the device (do not release reset),
- Hold the reset button until the green light is flashing (Approx. 15s)
- launch tftp, set mode to binary and connect to 192.168.1.1
- put the factory firmware image
- All leds will switch off (like a power off), this is normal
- Wait for the device to reboot in the new OpenWRT image (max 5 mins)
- The first boot will take longer than usual.
- After boot, the Device IP on the ethernet port is 192.168.1.1

Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com>
[drop unneeded includes in dts, wrap commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-03-16 23:14:25 +09:00
Sungbo Eo
fe34001ee5 Revert "ramips: add support for Netgear WN3000RPv3"
This reverts commit 7bc20cb614.

It adds support for Netgear WN3100RPv2, but the commit title is wrong.
It will be re-added with the correct title.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-03-16 23:10:45 +09:00
Rodolphe de Saint Léger
7bc20cb614 ramips: add support for Netgear WN3000RPv3
This patch adds support for the Netgear WN3100RPv2
http://www.netgear.com/support/product/wn3100rpv2.aspx

Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Stock firmware based on OpenWRT Kamikaze

Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577

This device seems to be same hardware as a WN3000RPv3

Flash instructions:
- Use the Netgear WebUI to upgrade to OpenWRT using the factory image
  (see note below),
- Use the sysupgrade image for upgrading versions from OpenWRT,
- TFTP recovery procedure can be used to flash the factory image
  (preferred method).

Note:
- The WebUI may not reboot automatically, wait at least 5 minutes before
  powercycling the device

Flashing using TFTP:
- Set you IP address to 192.168.1.10/24 (no gateway)
- Connect your machine to the Ethernet port
- Power off the device and wait for 10 seconds,
- Hold the reset button and power on the device (do not release reset),
- Hold the reset button until the green light is flashing (Approx. 15s)
- launch tftp, set mode to binary and connect to 192.168.1.1
- put the factory firmware image
- All leds will switch off (like a power off), this is normal
- Wait for the device to reboot in the new OpenWRT image (max 5 mins)
- The first boot will take longer than usual.
- After boot, the Device IP on the ethernet port is 192.168.1.1

Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com>
[drop unneeded includes in dts, wrap commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-03-16 22:36:04 +09:00
Pawel Dembicki
be89c9eec4 ramips: mt7620: Add support for D-Link DWR-961 A1
The DWR-961 A1 Wireless Router is based on the MT7620A SoC.
It's a merge of two Amit boards: DWR-960 with ethernet part
of Lava LR-25G001.

ROMID it's taken from Telenor branded version and it works with tested
device. Images from D-Link site for this router are from DWR-953 and it
have ROMID DLK6E2424001. I don't know if it's mistake on web-site
or if it's will require different image.

Specification:

- MediaTek MT7620A (580 Mhz)
- 128 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612 mpcie card)
- 5x 10/100/1000 Mbps Ethernet: 4xLAN and 1xWAN (QCA8337)
- 2x internal, non-detachable antennas (Wifi 2.4G)
- 3x external, detachable antennas (2x LTE, 1x Wifi 5G)
- 1x LTE modem cat 6
- UART (J5) header on PCB (57600 8n1)
- 13x LED, 2x button
- JBOOT bootloader

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2022-03-16 22:31:14 +09:00
Petr Štetiar
fb2801b82c mt7620: fix missing kernel config symbol
Fixes following missing kernel config symbol after adding GPIO watchdog:

  Software watchdog (SOFT_WATCHDOG) [M/n/y/?] m
  Watchdog device controlled through GPIO-line (GPIO_WATCHDOG) [Y/n/m/?] y
    Register the watchdog as early as possible (GPIO_WATCHDOG_ARCH_INITCALL) [N/y/?] (NEW)

Fixes: 1a97c03d86 ("rampis: feed zbt-we1026 external watchdog")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-02-28 21:32:32 +01:00
Arvid E. Picciani
1a97c03d86 rampis: feed zbt-we1026 external watchdog
Without feeding the gpio watchdog, the board will reset after 90 seconds

Signed-off-by: Arvid E. Picciani <aep@exys.org>
2022-02-28 15:17:11 +01:00
Davide Fioravanti
8fde82095b ramips: add support for Wavlink WL-WN535K1
The Wavlink WL-WN535K1 is a "mesh" router with 2 gigabit ethernet ports
and one fast ethernet port. Mine is branded as Talius TAL-WMESH1.
It can be found in kits of 2 or 3 (WL-WN535K2 or WL-WN535K3).
The motherboard is labelled as WS-WN535G3-B-V1.2 so this image could
potentially work for WL-WN535G3R and WS-WN535G3R with little to none
effort, but it's untested.

Hardware
--------
SoC:   Mediatek MT7620A
RAM:   64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
  - 2x 10/100/1000 Mbps Ethernet (RTL8211F)
  - 1x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
  - 2.4GHz: 1x (integrated in SOC) (2x2:2)
  - 5GHz:   1x MT7612E (2x2:2)
  - 4 internal antennas
BTN:
  - 1x Reset button
  - 1x Touchlink button (set to WPS)
  - 1x ON/OFF switch
LEDS:
  - 1x Red led (system status)
  - 1x Blue led (system status)
  - 3x Green leds (ethernet port status/act)
UART:
  - 57600-8-N-1

Everything works correctly.

Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.

Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on WN535K1_V1510_200916 firmware version.

1) Go to http://192.168.10.1/webcmd.shtml

2) Type the following line in the "Command" input box and then press enter:
	mkdir /etc_ro/lighttpd/www/dev; dd if=/dev/mtd0ro of=/etc_ro/lighttpd/www/dev/mtd0ro

3) After few seconds in the textarea should appear this output:
		16384+0 records in
	16384+0 records out

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the
   content of the whole NOR. If the file size is 0 byte, stop reading
   and ask for help in the forum.

5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type:
	rm /etc_ro/lighttpd/www/dev/mtd0ro;for i in 1 2 3 4 5; do dd if=/dev/mtd${i}ro of=/etc_ro/lighttpd/www/dev/mtd${i}ro; done

6) After few seconds, in the textarea should appear this output:
		384+0 records in
	384+0 records out
	128+0 records in
	128+0 records out
	128+0 records in
	128+0 records out
	14720+0 records in
	14720+0 records out
	1024+0 records in
	1024+0 records out

   If your output doesn't match mine, stop reading and ask for
   help in the forum.

7) Open the following links to download the partitions of the OEM FW:
	http://192.168.10.1/dev/mtd1ro
	http://192.168.10.1/dev/mtd2ro
	http://192.168.10.1/dev/mtd3ro
	http://192.168.10.1/dev/mtd4ro
	http://192.168.10.1/dev/mtd5ro

   If one (or more) of these files are 0 byte, stop reading and ask
   for help in the forum.

8) Store these downloaded files in a safe place.

9) Reboot your router to remove any temporary file in ram.

Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update_mesh.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.

Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.

Notes
-----
1) Router mac addresses:
   LAN		XX:XX:XX:XX:XX:E2 (factory @ 0x28)
   WAN		XX:XX:XX:XX:XX:E3 (factory @ 0x2e)
   WIFI 2G	XX:XX:XX:XX:XX:E4 (factory @ 0x04)
   WIFI 5G	XX:XX:XX:XX:XX:E5 (factory @ 0x8004)

   LABEL	XX:XX:XX:XX:XX:E5

2) The OEM firmware upgrade page accepts only files containing the
   string "WN535K1" in the filename.

3) Additional notes 1,2,3 in the WS-WN583A6 commit are still valid
(92780d80ab)

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[remove trailing whitespace]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-01-30 01:15:23 +09:00
Kyoungkyu Park
6041c693dd ramips: add support for HUMAX E2
HUMAX E2 (also known as HUMAX QUANTUM E2) is a 2.4/5GHz band AC router,
based on MediaTek MT7620A.

Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB (MXIC MX25L6405D)
- WiFi:
  - 2.4GHz: SoC internal
  - 5GHz: MT7610E
- Ethernet: 1x 10/100Mbps
  - Switch: SoC internal
- UART: J2 (57600 8N1)
  - pinout: [3V3] (RXD) (GND) (TXD)

Installation and Recovery via TFTP:
1. Connect ethernet cable between Router port and PC Ethernet port.
2. Set your computer to a static IP **192.168.1.1**
3. Turn the device off and wait a few seconds. Hold the WPS button on front
   of device and insert power.
4. Send a firmware image to **192.168.1.6** using TFTP.
   You can use any TFTP client. (tftp, curl, Tftpd64...)
5. Wait until Power LED stop flashing. **DO NOT TURN OFF DEVICE!**
   The device will be automatically rebooted.

Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space>
2022-01-15 20:05:46 +09:00
Sungbo Eo
482a7e23a4 ramips: add support for WeVO AIR DUO
WeVO AIR DUO is a 1-bay NAS & 802.11ac (Wi-Fi 5) router, based on
MediaTek MT7620A.

Specifications:
* SoC: MT7620A
* RAM: 64 MiB
* Flash: SPI NOR 16 MiB
* USB & SATA bridge controller: JMicron JMS567
  * SATA 6Gb/s: 2.5" drive slot
  * USB 3.0: Micro-B
  * USB 2.0: connected to SoC
* Wi-Fi:
  * 2.4 GHz: SoC built-in
  * 5 GHz: MT7612EN
* Ethernet: 5x 1GbE
  * Switch: MT7530WU
* UART: 4-pin 1.27 mm pitch through-hole (57600 baud)
  * Pinout: (3V3)|(RXD) (TXD) (GND)

Notes:
* The drive is accessible through the external USB port only when the
  router is turned off.

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
    The image filename should have ".upload" extension.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-29 20:35:57 +01:00
Sergey Ryazanov
b61ab8f57e kernel: filter out both Clang and LLD versions
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.

Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2021-12-17 16:16:34 +01:00
Sungbo Eo
cc3e390a74 ramips: mt7620: tidy up 02_network
* fix alphabetic sorting
* consolidate duplicate cases

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-12-16 22:28:58 +09:00
Rui Salvaterra
c772783394 ramips: remove Linux 5.4 support
We're at 5.10 stable, this can finally go.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-12-15 09:40:03 +00:00
Pawel Dembicki
a82fa5bcd4 ramips: mt7620: Enable PHY aneg of Lava LR-25G001
In 20b09a2125 Lava LR-25G001 router have problem with two inactive
ethernet ports. JBOOT bootloader didn't configure ethernet devices by default.
The same situation was there. It is required to enable all phy ports.
This is fragment of stock bootlog:

switch reg write_athr offset=90, value=2b0
switch reg write_athr offset=8c, value=2b0
switch reg write_athr offset=88, value=2b0
switch reg write_athr offset=84, value=2b0
switch reg write_athr offset=80, value=2b0

This patch adds proper registers configuration ar8337 initvals.
0x2b0 value causes force flow control configuration, 0x1200 was used
instead (flow control config auto-neg with phy). [1]

When switch is now ok, let's fix port numeration too.

Fixes: 20b09a2125 ("ramips: add support for Lava LR-25G001")

[1] https://github.com/openwrt/openwrt/pull/4806#issuecomment-982019858

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2021-12-04 00:36:47 +01:00
Mathias Kresin
1470009bf8 kernel: 5.10: packet mangling code only for ar8216 driver
Only the ar8216 switch driver uses the packet mangling code.

Update the kernel configs accordingly.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2021-11-02 22:36:41 +01:00
Jani Partanen
e06aaba4e3 ramips: fix LAVA LR-25G001 broken wifi led triggers
LED labels for this device are different in 01_leds file and in device
DTS. Switch to DT triggers, which works on Telewell TW-4 (LTE) clone
device.

This has not been tested on the LR-25G001 itself, just on the clone
mentioned above.

Fixes: 20b09a2125 ("ramips: add support for Lava LR-25G001")

Signed-off-by: Jani Partanen <rtfm@iki.fi>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-10-30 22:11:23 +02:00
Andrea Poletti
de0c380a5f ramips: add support for Sitecom WLR-4100 v1 002
Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router
Specification:
SoC: MT7620A
RAM: 64 MB DDR2
Flash: MX25L6405D SPI NOR 8 MB
WIFI: 2.4 GHz integrated
Ethernet: 5x 10/100/1000 Mbps QCA8337
USB: 1x 2.0
LEDS: 2x GPIO controlled, 5x switch
Buttons: 1x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
      white triangle on PCB:

    VCC 3.3V
    GND
    TX
    RX

    baud: 115200, parity: none, flow control: none

Installation

    Connect to one of LAN (yellow) ethernet ports,
    Open router configuration interface,
    Go to Toolbox > Firmware,
    Browse for OpenWrt factory image with dlf extension and hit Apply,
    Wait few minutes, after the Power LED will stop blinking, the router is
    ready for configuration.

Known issues
Some USB 2.0 devices work at full speed mode 1.1 only

MAC addresses

factory partition only contains one (binary) MAC address in 0x4.
u-boot-env contains four (ascii) MAC addresses, of which two appear
to be valid.

  factory     0x4       **:**:**:**:b9:84  binary
  u-boot-env  ethaddr   **:**:**:**:b9:84  ascii
  u-boot-env  wanaddr   **:**:**:**:b9:85  ascii
  u-boot-env  wlanaddr  00:AA:BB:CC:DD:12  ascii
  u-boot-env  iNICaddr  00:AA:BB:CC:DD:22  ascii

The factory firmware only assigns ethaddr. Thus, we take the
binary value which we can use directly in DTS.

Additional information
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), based on RT3352 SoC

Signed-off-by: Andrea Poletti <polex73@yahoo.it>
[remove config DT label, convert to nvmem, remove MAC address
 setup from u-boot-env, add MAC address info to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-09-05 23:52:35 +02:00
David Yang
38cb500516 ramips: expose ephy leds for miwifi-mini
Give users more control by exposing ephy leds.

Signed-off-by: David Yang <mmyangfl@gmail.com>
[remove execute bit on 01_leds, add status for gpio2]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-25 01:42:17 +02:00
Shiji Yang
a73a8269e1 ramips: add support for DomyWifi DM202/DM203/DW22D
Specifications:
* SOC: MT7620A + MT7610E
* ROM: 16 MiB spi flash (W25Q128FVSG)
* RAM: 128 MiB DDR2 (W971GG6KB-25)
* WAN: 10/100M *1
* LAN: 10/100M *4
* USB: Type-A USB2.0 *1
* SD: MicroSD *1
* Button: Reset *1
* Antennas: 2.4 GHz *2 + 5 GHz *1
* TTL Baudrate: 57600
* U-Boot Recovery: IP: 10.10.10.123, Server: 10.10.10.3

Installation:
* Web UI Update
  1. Open http://192.168.10.1/upgrade.html in the browser.
  2. Rename firmware to a short name like firmware.bin and then upload it.
  3. Fill in the password column with the following content:
  password | mtd -x mIp2osnRG3qZGdIlQPh1 -r write /tmp/firmware.bin firmware
* TFTP + U-Boot
  1. Connect device with a TTL cable.
  2. Press "2" when booting to select "Load system code then write to Flash via TFTP".
  3. Upload firmware by tftpd64, it will boot when write instruction is executed.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-08-25 01:42:16 +02:00
Shiji Yang
80e70be0ab ramips: add new flash layout support to Phicomm K2
Descriptions:
Phicomm K2 (PSG1218) got a new "permanent_config" partition after
update firmware to v22.5. This partition located in front of the
firmware partition, same as The Phicomm K2P and K2G. Due to this
change the new bootloader can't load previous firmware any more.
This commit is aimed at add support for Phicomm K2 which official
firmware version is 22.5.x or newer. For which runs old firmware
version, just update OpenWrt that has a prefix of "k2-v22.4".
For uniform naming, this commit also changed the model name
PSG1218 to a more recognizable name K2, refer to Phicomm K2G,
K2P K2T.

OpenWrt selection table:
official firmware version           OpenWrt
v22.4.x.x or older              phicomm_k2-v22.4
v22.5.x.x or newer              phicomm_k2-v22.5

Installation:
Same as Phicomm K2G, K2P, PSG1208.
a. TFTP + U-Boot
b. Open telnet by some web page vulnerability (Search Baidu by key
   words "K2 telnet"), and then we can upload firmware image to
   /tmp and write it to firmware partition with mtd instruction.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[rebase, add/harmonize version in model variables, fix version typo
 in commit message, wrap commit message properly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-08-24 20:26:00 +02:00
David Bauer
373c08bcbb ramips: fix missing NVMEM subsystem
MAC address retrieval was switched to more generic upstream (5.13) NVMEM
based solution in commit 06bb4a5018 ("ramips: convert mtd-mac-address
to nvmem implementation") , but NVMEM subsystem wasn't enabled in the
kernel, so fix it now.

References: https://github.com/openwrt/openwrt/pull/4041#issuecomment-883322801
Fixes: 06bb4a5018 ("ramips: convert mtd-mac-address to nvmem implementation")
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit message]
2021-07-21 11:39:39 +02:00
David Bauer
38db2f12d6 ramips: add AW9523 I2C GPIO expander driver
This adds a driver for the AW9523 I2C GPIO expander.

This driver is required to make LEDs as well as buttons on the Tenbay
T-MB5EU-V01 work.

This driver already had several upstream iterations. I'm working to
push this driver to mainline.

Ref: https://patchwork.ozlabs.org/project/linux-gpio/list/?series=226287

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-06-27 21:40:15 +02:00
Michael Pratt
2adeada045 ramips: mt7620: disable SOC VLANs for external switches
These boards have AR8327 or QCA8337 external ethernet switch.
The SOC also has it's own internal switch
where VLAN is now enabled by default.

Changes to preinit caused all switches to have VLANs enabled by default
even if they are not configured with a topology in uci_defaults
(see commit f017f617ae)

When both internal and external switches have VLANs,
and the external switch has both LAN and WAN,
the TX traffic from the SOC cannot flow to the tagged port on the external switch
because the VLAN IDs are not matching.

So disable the internal switch VLANs by default on these boards.

Also, add a topology for the internal switch,
so that on LuCI there is not an "unknown topology" warning.

In theory, it may be possible to have LAN ports on both switches
through internal and external PHYs, but there are no known boards that have this.

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2021-06-23 14:22:19 +08:00
Ben Gainey
a509b80065 ramips: add support for the Wavlink WL-WN579X3
About the device
----------------

SoC: MediaTek MT7620a @ 580MHz
RAM: 64M
FLASH: 8MB
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 2x (RTL8211F)
BTN: - WPS
- Reset
- Router/Repeater/AP (3-way slide-switch)
LED: - WPS (blue)
- 3-segment Wifi signal representation (blue)
- WiFi (blue)
- WAN (blue)
- LAN (blue)
- Power (blue)
UART: UART is present as Pads with through-holes on the PCB. They are
located next to the reset button and are labelled Vcc/TX/RX/GND as
appropriate. Use 3.3V, 57600-8N1.

Installation
------------

Using the webcmd interface
--------------------------

Warning: Do not update to the latest Wavlink firmware (version
20201201) as this removes the webcmd console and you will need to
use the serial port instead.

You will need to have built uboot/sqauashfs image for this device,
and you will need to provide an HTTP service where the image can
be downloaded from that is accessible by the device.
You cannot use the device manufacturers firmware upgrade interface
as it rejects the OpenWrt image.

1. Log into the device's admin portal. This is necessary to
   authenticate you as a user in order to be able to access the
   webcmd interface.
2. Navigate to http://<device-ip>/webcmd.shtml - you can access
   the console directly through this page, or you may wish to
   launch the installed `telnetd` and use telnet instead.
   * Using telnet is recommended since it provides a more
     convenient shell interface that the web form.
   * Launch telnetd from the form with the command `telnetd`.
   * Check the port that telnetd is running on using
     `netstat -antp|grep telnetd`, it is likely to be 2323.
   * Connect to the target using `telnet`. The username should
     be `admin2860`, and the password is your admin password.
3. On the target use `curl` to download the image.
   e.g.  `curl -L -O http://<some-other-lan-ip>/openwrt-ramips-mt7620-\
          wavlink_wl-wn579x3-squashfs-sysupgrade.bin`.
   Check the hash using `md5sum`.
4. Use the mtd_write command to flash the image.
   * The flash partition should be mtd4, but check
     /sys/class/mtd/mtd4/name first. The partition should be
     called 'Kernel'.
   * To flash use the following command:
     `mtd_write -r -e /dev/mtd<n> write <image-file> /dev/mtd<n>`
     Where mtd<n> is the Kernel partition, and <image-file> is
     the OpenWrt image previously downloaded.
   * The command above will erase, flash and then reboot the
     device. Once it reboots it will be running OpenWrt.

Connect via ssh to the device at 192.168.1.1 on the LAN port.
The WAN port will be configured via DHCP.

Using the serial port
---------------------

The device uses uboot like many other MT7260a based boards. To
use this interface, you will need to connect to the serial
interface, and provide a TFTP server. At boot follow the
bootloader menu and select option 2 to erase/flash the image.
Provide the address and filename details for the tftp server.
The bootloader will do the rest.

Once the image is flashed, the board will boot into OpenWrt. The
console is available over the serial port.

Signed-off-by: Ben Gainey <ba.gainey@googlemail.com>
2021-06-06 18:56:45 +02:00
Shiji Yang
4a9f389ed2 ramips: split Youku YK1 to YK-L1 and YK-L1c
Device specifications:
* Model: Youku YK-L1/L1c
* CPU: MT7620A
* RAM: 128 MiB
* Flash: 32 MiB (YK-L1)/ 16 MiB (YK-L1c)
* LAN: 2* 10M/100M Ports
* WAN: 1* 10M/100M Port
* USB: 1* USB2.0
* SD: 1* MicroSD socket
* UART: 1* TTL, Baudrate 57600

Descriptions:
  Previous supported device YOUKU yk1 is actually Youku YK-L1. Though they look
  really different, the only hardware difference between the two models is flash
  size, YK-L1 has 32 MiB flash but YK-L1c has 16MiB. It seems that YK-L1c can
  compatible with YK-L1's firmware but it's better to split it to different models.

  It is easy to identify the models by looking at the label on the bottom of the
  device. The label has the model number "YK-L1" or "YK-L1c". Due to different flash
  sizes, YK-L1c that using previous YK-L1's firmware needs to apply "force update"
  to install compatible firmware, so please backup config file before system upgrade.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[use more specific name for DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-06-05 23:39:14 +02:00
Shiji Yang
e57e460dc7 ramips: fix mac addresses of Youku YK1
MAC addresses read from official firmware

        value       location
Wlan    xx 71 de    factory@0x04
Lan     xx 71 dd    factory@0x28
Wan     xx 71 df    factory@0x2e
Label   xx 71 dd    factory@0x28

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[fix sorting in 02_network, redact commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-05-10 14:41:06 +02:00
Rui Salvaterra
3326b5e75c treewide: switch the timer frequency to 100 Hz
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2021-04-21 10:31:10 +01:00
Shiji Yang
882a6116d3 ramips: improve pinctrl for Youku YK-L1
1. rename led pin "air" to a more common name "wlan" and use "phy0tpt" to trigger it.
2. led "wan" can be triggered by ethernet pinctrl by default so just drop it.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2021-04-10 20:48:26 +02:00
Shiji Yang
b88d2850c6 ramips: correct switch config of Youku yk1
There are only two lan ports and one wan port on Youku yk1

Fixes: e9baf8265b ("ramips: add support for Youku YK1")

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-27 16:54:15 +01:00
Adrian Schmutzler
85b1f4d8ca treewide: remove execute bit and shebang from board.d files
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.

Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.

Note:

This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-06 11:30:06 +01:00
Ilya Lipnitskiy
b021642cac ramips: 5.10: refresh configs
Run-tested on Ubiquiti EdgeRouter X.

Compile tested on all other subtargets.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-06 11:24:12 +01:00
Ilya Lipnitskiy
a9966793e8 ramips: copy config-5.4 to config-5.10
Strict copy, no changes made.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-06 11:24:12 +01:00
Adrian Schmutzler
cc4ee2eeb4 Revert "ramips: add support for kernel 5.10"
This reverts commit b4aad29a1d.

This was accidentally folded into a single commit. Remove it and
apply it properly again.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-03-06 11:23:38 +01:00
Ilya Lipnitskiy
b4aad29a1d
ramips: add support for kernel 5.10
Enable testing kernel.

Delete upstreamed patches:
 0098-disable_cm.patch can be dropped, upstream fixed CM handling.

Fix compile errors by using new kernel APIs.

Fix fuzz by manually editing patches to ensure the code goes in the
right place.

For 721-NET-no-auto-carrier-off-support.patch, revert upstream commit
a307593a6 to keep the OpenWrt ralink driver operational.

Add mt7621-pci-phy patch to select REGMAP_MMIO as discussed in PR #3693
and #3952.

Rename patches to follow the 3-digit classification from the OpenWrt
Developer Guide.

Run automatic quilt refresh.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-05 23:55:51 +00:00
Ilya Lipnitskiy
38ba1f9b4c
ramips: 5.4: refresh configs
Automatic refresh by running make kernel_oldconfig on each target.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
2021-03-05 23:55:46 +00:00
Shiji Yang
567a88e4b9 ramips: fix Phicomm PSG1218A switch port labels
The lan port sequence was reversed compared to the labels.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-22 18:49:57 +01:00
Shiji Yang
55263ffedb ramips: correct/add Phicomm K2x WAN/label MAC address
Phicomm K2G:
add missing label_mac

Phicomm PSG1218A & PSG1218B:
The previous wan mac was set as factory@0x28 +1 (originally based
on the default case for the ramips target), but the correct wan mac
is factory@0x28 -1, being equal to factory@0x2e.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-22 17:32:35 +01:00
Adrian Schmutzler
703fd8aef4 ramips: remove generic profiles
On a platform with many very different devices, like found on ramips,
the generic profiles seem like remnants of the past that do not
have a real use anymore.

Remove them to have one thing less to maintain.

Actually, rt288x didn't have a default profile in the first place.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
2021-01-27 21:31:20 +01:00
Nuno Goncalves
2a860bf4f4 ramips: add support for Wavlink WL-WN530HG4
Same hardware as Phicomm K2G but different flash layout.

Specification:
- SoC: MediaTek MT7620A
- Flash: 8 MB
- RAM: 64 MB
- Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5)
- Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped
  with external PA.
- UART: 1 x UART on PCB - 57600 8N1

Flash instruction:
To avoid requiring UART for TFTP a dual flash procedure is suggested
to install the squashfs image:
1. Rename openwrt-ramips-mt7620-wavlink_wl-wn530hg4-initramfs-kernel.bin
   to WN530HG4-WAVLINK.
2. Flash this file with the factory web interface.
3. With OpenWRT now running use standard sysupgrade to install the
   squashfs image.

Signed-off-by: Nuno Goncalves <nunojpg@gmail.com>
[remove dts-v1, remove model from LED labels, wrap commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-27 21:20:16 +01:00
Adrian Schmutzler
2230fe3922 ramips: remove set_wifi_led function in 01_leds
While we mostly use the ucidef_set_led_* functions directly in 01_leds
we still have the set_wifi_led function in parallel for several old
devices. This is not only inconsistent with the other definitions,
it also links to the wlan0 interface instead of using a phy trigger
which would be independent of the interface name (and is used for
all newer devices anyway). Apart from that, the standard names
"wifi" and "wifi-led" are not very helpful in a world with different
radio bands either.

Thus, this patch removes the set_wifi_led function and puts the
relevant commands into the cases explicitly. This makes the
mechanism used more evident and will hopefully lead to some future
improvements or at least prevent some copy-pasting of the old
setups.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-02 14:51:57 +02:00
Adrian Schmutzler
ed5933beb6 ramips: remove option to set WiFi LED via aliases
In ramips, it's not common to use an alias for specifying the WiFi
LED; actually only one device uses this mechanism (TL-WR841N v14).

Particularly since the WiFi LEDs are typically distinguished between
2.4G and 5G etc. it is also not very useful for this target.

Thus, this patch removes the setup lines for this mechanism and
converts the TL-WR841N v14 to the normal setup.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-02 14:51:57 +02:00
Adrian Schmutzler
c846dd91f0 ramips: remove model name from LED labels
Like in the previous patch for ath79 target, this will remove the
"devicename" from LED labels in ramips as well.

The devicename is removed in DTS files and 01_leds, consolidation
of definitions into DTSI files is done where (easily) possible,
and migration scripts are updated.

For the latter, all existing definitions were actually just
devicename migrations anyway. Therefore, those are removed and
a common migration file is created in target base-files. This is
actually another example of how the devicename removal makes things
easier.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-10-02 14:51:57 +02:00
Adrian Schmutzler
3fc7860961 ramips: assign LEDs for RAVPower RP-WD03
According to the User Manual, there is a "Wi-Fi LED" with blue and
green colors, doing the following by default:

  Flashing Blue: System loading
  Solid Blue: System loaded
  Flashing Green: Connecting to the Internet
  Solid Green: Connected to the Internet

According to this vendor behavior, we keep refer to the LED as "wifi"
but implement the according default behavior as in OEM firmware.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-12 01:24:30 +02:00
Adrian Schmutzler
07aa858a73 ramips: fix partitions and boot for RAVPower RP-WD03
The RAVPower RP-WD03 is a battery powered router, with an Ethernet and
USB port. Due due a limitation in the vendor supplied U-Boot bootloader,
we cannot exceed a 1.5 MB kernel size, as is the case with recent builds
(i.e. post v19.07). This breaks both factory and sysupgrade images.

To address this, use the lzma loader (loader-okli) to work around this
limitation.

The improvements here also address the "misplaced" U-Boot environment
partition, which is located between the kernel and rootfs in the stock
image / implementation. This is addressed by making use of mtd-concat,
maximizing space available in the booted image.
This will make sysupgrade from earlier versions impossible.

Changes are based on the recently supported HooToo HT-TM05, as the
hardware is almost identical (except for RAM size) and is from the same
vendor (SunValley). While at it, also change the SPI frequency
accordingly.

Installation:

 - Download the needed OpenWrt install files, place them in the root
   of a clean TFTP server running on your computer. Rename the files as,
   - openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-kernel.bin => kernel
   - openwrt-ramips-mt7620-ravpower_rp-wd03-squashfs-rootfs.bin => rootfs
 - Plug the router into your computer via Ethernet
 - Set your computer to use 10.10.10.254 as its IP address
 - With your router shut down, hold down the power button until the first
   white LED lights up.
 - Push and hold the reset button and release the power button. Continue
   holding the reset button for 30 seconds or until it begins searching
   for files on your TFTP server, whichever comes first.
 - The router (10.10.10.128) will look for your computer at 10.10.10.254
   and install the two files. Once it has finished installation, it will
   automatically reboot and start up OpenWrt.
 - Set your computer to use DHCP for its IP address

Notes:

 - U-Boot environment can be modified, u-boot-env is preserved on initial
   install or sysupgrade
 - mtd-concat functionality is included, to leave a "hole" for u-boot-env,
   combining the OEM kernel and rootfs partitions

Most of the changes in this commit are the work of Russell Morris (as
credited below), I only wrapped them up and added compat-version.
Thanks to @mpratt14 and @xabolcs for their help getting the lzma loader
to work!

Fixes: 5ef79af4f8 ("ramips: add support for Ravpower WD03")

Suggested-by: Russell Morris <rmorris@rkmorris.us>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-11 19:31:03 +02:00
Adrian Schmutzler
a4e5b8897a ramips: use proper name for RAVPower RP-WD03
The proper model name is RP-WD03 (i.e. with the RP- prefix).

Adjust all names to that.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-11 19:18:54 +02:00
Russell Morris
45a81f7056 ramips: add support for HooToo HT-TM05
The HooToo HT-TM05 is a battery powered router, with an Ethernet and USB port.
Vendor U-Boot limited to 1.5 MB kernel size, so use lzma loader (loader-okli).

Specifications:

  SOC:     MediaTek MT7620N
  BATTERY: 10400mAh
  WLAN:    802.11bgn
  LAN:     1x 10/100 Mbps Ethernet
  USB:     1x USB 2.0 (Type-A)
  RAM:     64 MB
  FLASH:   GigaDevice GD25Q64, Serial 8 MB Flash, clocked at 50 MHz
           Flash itself specified to 80 MHz, but speed limited by mt7620 SPI
           fast-read enabled (m25p)
  LED:     Status LED (blue after boot, green with WiFi traffic
           4 leds to indicate power level of the battery (unable to control)
  INPUT:   Power, reset button

MAC assignment based on vendor firmware:

  2.4 GHz    *:b4   (factory 0x04)
  LAN/label  *:b4   (factory 0x28)
  WAN        *:b5   (factory 0x2e)

Tested and working:

 - Ethernet
 - 2.4 GHz WiFi (Correct MAC-address)
 - Installation from TFTP (recovery)
 - OpenWRT sysupgrade (Preserving and non-preserving), through the usual
   ways: command line and LuCI
 - LEDs (except as noted above)
 - Button (reset)
 - I2C, which is needed for reading battery charge status and level
 - U-Boot environment / variables (from U-Boot, and OpenWrt)

Installation:

 - Download the needed OpenWrt install files, place them in the root
   of a clean TFTP server running on your computer. Rename the files as,
   - ramips-mt7620-hootoo_tm05-squashfs-kernel.bin => kernel
   - ramips-mt7620-hootoo_tm05-squashfs-rootfs.bin => rootfs
 - Plug the router into your computer via Ethernet
 - Set your computer to use 10.10.10.254 as its IP address
 - With your router shut down, hold down the power button until the first
   white LED lights up.
 - Push and hold the reset button and release the power button. Continue
   holding the reset button for 30 seconds or until it begins searching
   for files on your TFTP server, whichever comes first.
 - The router (10.10.10.128) will look for your computer at 10.10.10.254
   and install the two files. Once it has finished installation, it will
   automatically reboot and start up OpenWrt.
 - Set your computer to use DHCP for its IP address

Notes:

 - U-Boot environment can be modified, u-boot-env is preserved on initial
   install or sysupgrade
 - mtd-concat functionality is included, to leave a "hole" for u-boot-env,
   combining the OEM kernel and rootfs partitions

I would like to thank @mpratt14 and @xabolcs for their help getting the
lzma loader to work!

Signed-off-by: Russell Morris <rmorris@rkmorris.us>
[drop changes in image/Makefile, fix indent and PKG_RELEASE in
uboot-envtools, fix LOADER_FLASH_OFFS, minor commit message facelift,
add COMPILE to Device/Default]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-03 14:15:30 +02:00
Adrian Schmutzler
66ab1fb395 ramips: drop support for kernel 4.14
The target seems to be working on 5.4, so drop 4.14 support in
preparation for removing it from master entirely.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-02 16:29:23 +02:00
Petr Štetiar
a14f5bb4bd treewide: use wpad-basic-wolfssl as default
In order to support SAE/WPA3-Personal in default images. Replace almost
all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for
consistency. Keep out ar71xx from the list as it won't be in the next
release and would only make backports harder.

Build-tested (build-bot settings):
ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway,
sunxi: a53

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-20 14:19:39 +02:00
Shibajee Roy
a673ac66fa ramips: add support for Netgear JWNR2010 v5
Specification:
 - CPU: MediaTek MT7620N (580 MHz)
 - Flash size: 4 MB NOR SPI
 - RAM size: 32 MB DDR1
 - Bootloader: U-Boot
 - Wireless: MT7620N 2x2 MIMO 802.11b/g/n (2.4 GHz)
 - Switch: MT7620 built-in 10/100 switch with vlan support
 - Ports: 4x LAN, 1x WAN
 - Others: 7x LED, Reset button, UART header on PCB (57600 8N1)

Flash instructions:
 1. Use ethernet cable to connect router with PC/Laptop, any router
    LAN port will work.
 2. To flash openwrt we are using nmrpflash[1].
 3. Flash commands:
      First we need to identify the correct Ethernet id.

        nmrpflash -L

        nmrpflash -i net* -f openwrt-ramips-mt7620-netgear_jwnr2010-v5-squashfs-factory.img

      This will show something like "Advertising NMRP server on net*..." (net*, *=1,2,3... etc.)

 4. Now remove the power cable from router back side and immediately connect it again.
    You will see flash notification in CMD window, once it says reboot the device just
    plug off the router and plug in again.

Revert to stock:
 1. Download the stock firmware from official netgear support[2].
 2. Follow the same nmrpflash procedure like above, this time just use the stock firmware.

        nmrpflash -i net* -f N300-V1.1.0.54_1.0.1.img

MAC addresses on stock firmware:
LAN = *:28 (label)
WAN = *:29
WLAN = *:28

On flash, the only valid MAC address is found in factory 0x4.

Special Note:
 This openwrt firmware will also support other netgear N300 routers like below as they
 share same stock firmware[3].
 JNR1010v2 / WNR614 / WNR618 / JWNR2000v5 / WNR2020 / WNR1000v4 / WNR2020v2 / WNR2050

[1] https://github.com/jclehner/nmrpflash
[2] https://www.netgear.com/support/product/JWNR2010v5.aspx
[3] http://kb.netgear.com/000059663

Signed-off-by: Shibajee Roy <ador250@protonmail.com>
[create DTSI, use netgear_sercomm_nor, disable by default, add MAC
addresses to commit message, add label MAC address]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-06 16:56:07 +02:00
Felix Fietkau
b0f7ea2853 kernel: unify CONFIG_GPIO_SYSFS in kernel configs
Enable it for all platforms

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-08-06 12:37:04 +02:00