Following errors were seen in the past on imx6 when using serial:
[ 22.617622] imx-uart 2020000.serial: DMA transaction error.
[ 22.623228] imx-uart 2020000.serial: DMA transaction error.
[ 22.628826] imx-uart 2020000.serial: DMA transaction error.
[ 22.648951] imx-uart 2020000.serial: DMA transaction error.
[ 22.654558] imx-uart 2020000.serial: DMA transaction error.
[ 22.660156] imx-uart 2020000.serial: DMA transaction error.
Which is the reason why DMA for the serial ports
got disabled in commits:
efb362cd93 ("imx6: disable dma on uart")
3b4241071d ("imx6: disable UART dma")
As indicated on mailinglist discussion, the cause seems to be
the usage of very old SDMA firmware which is present in the soc:
[ 0.624302] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2
[ 0.624318] imx-sdma 20ec000.sdma: Falling back to user helper
[ 64.531607] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
This patch adds the new firmware binary. (2196 bytes)
It is required to embed the binary into the kernel image, as it
gets loaded very early in the boot process where the rootfs is not
available yet:
[ 0.622966] imx-sdma 20ec000.sdma: loaded firmware 3.3
Extended testing shows that the DMA errors are not seen anymore
when using this newer firmware version.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The bump to kernel 4.14 caused a massive increase in kernel size.
For most targets, switching them to dynamic partitioning allowed
to cope with this.
On some targets, the kernel partition is located behind the rootfs,
which disallows switching to dynamic partitioning as the boot location
would be altered, requiring a u-boot change.
Also within the tiny section, which disables kernel symbols etc
to decrease the image size, the partition size is still too small.
Disable these targets for now, fixing image generation:
- Buffalo BHR-4GRV2
- Zbtlink ZBT-WE1526
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The NBG6617's LEDs are wrongly identified in the 01_leds boardinit
script (board instead of boardname), resulting in referencing
non-existent LEDs in UCI.
Signed-off-by: David Bauer <mail@david-bauer.net>
For each board, set the legacy name as well as the new based on the
compatible-string from devicetree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
remove /lib/oxnas.sh platform-specific board-detection and use
generic which is based on device-tree compatible node instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The BDFs for all boards were upstreamed to the ath10k-firmware
repository and linux-firmware.git.
We switched to the upstream board-2.bin, hence the files can be removed
here.
Keep the ipq-wifi package in case new boards are added. It might take
some time till board-2.bins send upstream are merged.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The NBG6617's boardfile was merged and this device can
now switch to the upstream ath10k board-2.bin.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch replaces the custom autoload quirk of the
RT-AC58U with a bootargs-append overwrite.
The vendor's u-boot doesn't leave the bootargs / cmdline alone,
so the it can't be overwritten in any other way right now...
And of course, this will be a lot of fun to deal with once
the device switches to the new spi-nand subsystem.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Kernel 4.14 is pretty large causing a build error as the partition is too small.
Expand the kernel partition a bit to make it fit.
* ubnt-uap-pro
* ubnt-unifi-outdoor-plus
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This target causes a build failure as the kernel image does not fit
into the kernel partition.
As the kernel is located behind the rootfs, it cannot be enlarged
as the boot entry location would get altered.
Disable this target for now.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Targets:
- TP-LINK ER355
- TP-LINK C25 V1
- TP-LINK C59 V1
- TP-LINK C7 V4
- TP-LINK C7 V5
Fixes build issues seen due to the kernel being too big
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
As mentioned in commit 5f24933 recent changes on ar71xx (switch to 4.14,
memory compaction, ...) cause an increase in kernel size, making it too
big for RE450.
RE450 images were not build due to the following error message:
os-image partition too big (more than 1572864 bytes): Success
Tested on RE450, device boots and was used to send this patch.
Reported-by: Enrico Mioso <mrkiko.rs@gmail.com>
Suggested-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[rewrote commit msg keeping it tight + fixed SoB lines]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This changes the OCEDO Koala flash-layout to a unified firmware
partition, thus making the ar71xx-generic kernel fit in flash.
Compile and runtested on OCEDO Koala.
Signed-off-by: David Bauer <mail@david-bauer.net>
[small title reword]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor
5 GHz AC access point with an integrated 120° 16 dBi antenna. The device
was previously known as LiteBeam AP ac but was later rebranded.
CPU: Atheros AR9342 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
Ports: 1 GbE port (PoE in)
WLAN: 5 GHz QCA899X (PCI)
The integrated QCA899X is a Ubiquiti branded part with modified vendor
and product id (0777:11ac9). It is very similar to the NanoStation loco
AC, except for the 2.4 GHz management radio (missing here).
Installation procedure is the same as the NanoStation [loco] AC:
1. Connect to serial header on device
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Regression introduced with 4.10 by 43c9127d94d62a232ed33ed2eab8a08657ce5472
Build will fail if system 'ar' does not support deterministic builds.
e.g. macOS with Xcode toolchain
Appears to be fixed upstream in 4.18 by af3901cbbd3de182aafb8ee553c825c0074df6a2
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
The WNDR4700 and the MBL have a dedicated HDD activity LED.
This patch adds the default led triggers to the DTS and
removes the entries in 01_leds.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
- order entries by mmio address where possible
- switch to lower-case address values
- comment on BSP u-boot behaviour in regards to
what it edits and look for
- annotate irq lines with the help of interrupt-names
- remove deprecated "device_type" properties
The pci and network device_type had to stay since
they are required by the drivers and u-boot.
the cpu and memory device_types will remain as well
as they are still part of the DT Spec.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
With the upcoming 4.19 release, the serial console on the
Netgear WNDR4700 would no longer work as it is never really
set and always relied on the kernel's serial code not to
change the baud rate.
On the stock firmware, Netgear forced the console setting
through a custom CONFIG_CMDLINE in their kernel to 115200.
Normally, they should have done it in a different way and
just passed the baudrate through a "console=..." kernel
parameter via the bootargs in the "/chosen" dt node.
But in their default u-boot bootcmd setting, they somehow
forgot to add the "run addtty", so there's no easy way to
pass the baudrate from u-boot to the kernel. So it has
to be forced as otherwise it ends up as 9600 baud.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
I noticed that the image generator for the Gemini generates
some 10+ MB files for the second (application) partition.
This is just wrong. The first 6144K partition named initramfs
easily fits OpenWRTs squashfs,jffs2 overlayed partitions
with nice headroom for storing configuration files.
Generate a blank partition for the hddapp.tgz file and delete
it after generating the firmware image - when performing
updates manually you just want the "rd.z" file around
anyways.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This creates a new kernel package for the fotg210 host
controller and uses that with the gemini to shrink the
kernel. The SQ201 needs the USB2 PCI package as well.
The build system required me to make kernel_oldconfig
beofore it would build without errors so some minor
unrelated Kconfig entries are changed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Newer batches of several Mikrotik boards contain this yet-unsupported
flash chip, for instance:
- rb941-2nd (hAP lite)
- rb952ui-5ac2nd (hAP ac lite)
- RBM33G
and probably other Mikrotik boards need this patch as well.
The patch was submitted upstream by Robert Marko: https://patchwork.ozlabs.org/patch/934181/
Closes: FS#1715
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Cc: Robert Marko <robimarko@gmail.com>
Refreshed all patches.
Altered patches:
- 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch
New symbol for arm targets:
- HARDEN_BRANCH_PREDICTOR
Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
In commit fec8fe8069 ("kernel: bump 4.9 to 4.9.116") [1], the following patch for removed:
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch
This patch contained fixes for both write and erase functions.
While the chip-detects for erase got fixed upstream [2],
some modifications are still required, even with the fixes applied.
While at it, also apply the same fix for target ath79,
which suffers the same issue.
Not doing so results in following errors seen:
Collected errors:
* pkg_write_filelist: Failed to open //usr/lib/opkg/info/luci-lib-ip.list: I/O error.
* opkg_install_pkg: Failed to extract data files for luci-lib-ip. Package debris may remain!
* opkg_install_cmd: Cannot install package luci-ssl.
* opkg_conf_write_status_files: Can't open status file //usr/lib/opkg/status: I/O error.
[ 0.780920] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 8.406396] jffs2: notice: (415) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 8.423476] mount_root: switching to jffs2 overlay
[ 270.902671] jffs2: Write of 1989 bytes at 0x005ce6f8 failed. returned -5, retlen 962
[ 270.931965] jffs2: Write of 1989 bytes at 0x005ceec0 failed. returned -5, retlen 0
[ 270.939631] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[ 270.950397] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[ 270.957838] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[ 270.968584] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[ 270.976027] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[ 270.986735] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[ 270.994225] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=fec8fe806963c96a6506c2aebc3572d3a11f285f
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v4.9.133&id=a0239d83e1cb60de5e78452d4708c083b9e3dcbe
Fixes: fec8fe8069 ("kernel: bump 4.9 to 4.9.116")
Signed-off-by: Fabio Bettoni <fbettoni@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Recent changes on ar71xx (switch to 4.14, memory compaction, ...) cause
an increase in kernel size, making it too big for some devices.
Move these devices to the tiny target, where kernel symbols and
optimization for speed are disabled, reducing the kernel size.
Devices:
- EnGenius ENS202EXT
- OCEDO Koala
Compile-tested targets:
- ar71xx->generic->default
- ar71xx->smallFlash->Default
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Add out of the box support for 802.11r and 802.11w to all targets not
suffering from small flash.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Mathias did all the heavy lifting on this, but I'm the one who should
get shouted at for committing.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
It's required to support devices using adjustable SoC pins for some
specific purpose (e.g. I2C, PWM, UART1).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Instead of reverting whole commit it's enough to just revert a single
line change. It seems the real problem with the regressing commit was a
bump of read chunk size. Switching back to 256 B chunks is enough to fix
the problem/regression.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
