The ubootloader of the M2M sets the reset bits for
both USB device and USB host during initialization
(to save a few mA of power during boot).
However, for the usb<->sata bridge to be properly
detected, it is necessary to clear both reset bits
as otherwise the kernel logs will just be filled
with:
usb 1-1: device descriptor read/64, error -145
...
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44248
Few characters in filenames (a plus sign, a dot) can be interpreted
specially by grep. This can lead to the omission of missing package
dependency. For example if we would have "some.file.so" then it
matches also "some2file.so". -F switch off special meaning
of any character and -x match against whole line.
Signed-off-by: Sławomir Demeszko <s.demeszko@wireless-instruments.com>
SVN-Revision: 44247
remove obsolete configuration settings
--disable-thread
--enable-nonblocking
--without-krb4
remove SSPI support
only supported on windows
correct --with/without-ca-path handling
only supported with OpenSSL and PolarSSL
correct LDAP/LDAPS protocol
add dependency libopenldap
added SCP/SFTP protocol
default "No"
depends on libssh2
added IDN support
default "No"
depends on libidn
added SMB protocol (new in 7.40)
default "No"
require 'cryptographic authentication' and either 'GnuTLS' or 'OpenSSL' selected
added Unix sockets support (new in 7.40)
default "No"
added error verbose messages
default "No"
changes to Makefile
Increase PKG_RELEASE
PKG_CONFIG_DEPENDS and CONFIGURE_ARGS
extended for new functionality
use "autoconf_bool" for all --enable/--disable options
restructure for easier reading
changes to Config.in
extended for new functionality
implement dependencies
restructure and grouping for easier reading
build tested on XUbuntu 14.10 x86 for x86 (generic) and ar71xx (WNDR3800)
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 44243
Part of rev 44173 added setting the SM Power Save capability in the hostapd.conf
file if the driver indicated that it was supported. It appears this was
incorrect, because the field in the actual HT Capabilities field in the AP
configuration is really a state indication. Just copying the state from the
capability resulted in the AP indicating that it had SMPS enabled all the time
if it supported SMPS. This effectively just disables all clients from sending
packets to the AP with more than one spatial stream, for no good reason.
So remove this part of the change.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
SVN-Revision: 44239
This patch adds support for Xiaomi MiWiFi Mini, a 802.11a/b/g/n/ac dual radio
wireless router based on the MediaTek MT7620a SoC.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 44238
- budget is decremented with completed frames, so don't check if done is
smaller
- ACK the interrupt before processing further frames to fix a small race
condition.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44234
It fails to build because of missing of_irq_parse_raw and incompatible
irq_create_of_mapping.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44230
* enclose the fixup in brackets
* match anything in the call to AM_GNU_GETTEXT_VERSION
* call it early (before autoreconf if both are specified)
* chain a call to autoreconf since it messes with configure.ac
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 44225
Replace the now defunct 062-mips_decompressor_build_fix.patch with another
patch that simply undefines the arch memset and memcpy defines to avoid
syntax errors in the redeclaration.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44223
The board is already supported by OpenWrt. WNR1000v2/WNR1000v2-VC are
pretty much the same as WNR2000v3/WNR612v2, therefore the same
initialization code and flash layout is used.
Signed-off-by: Ștefan Rusu <saltwaterc@gmail.com>
Tested-by: Douglas Fraser <1dsfraser@gmail.com>
SVN-Revision: 44221
This "patch to the patch" fixes a NULL pointer derefence crash in the new
intermediate software queues. The crash can be reproduced by injecting an
802.11 frame with a BSSID that does not belong to a configured vif. The
wperf tool (https://github.com/anyfi/wperf) may be convenient for doing
this.
Signed-off-by: Johan Almbladh <ja@anyfi.net>
SVN-Revision: 44220
Anchor search pattern when testing dependencies, otherwise the check may
succeed in cases where it shouldn't, e.g. when matching "udp_tunnel.ko"
against "ip6_udp_tunnel.ko".
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44207
Do not output faulty ".ko" dependency if a scanned .ko file has an empty
"depends=" specification, also replace the `grep | sed | awk` chain with a
single sed program.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44206
