The ZyXEL GS1900-8 is a 8 port switch without any PoE functionality or
SFP ports, but otherwise similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-8 v1.2
* SoC: Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash: Macronix MX25L12835F 16 MiB
* RAM: Nanya NT5TU128M8GE-AC 128 MiB DDR2 SDRAM
* Ethernet: 8x 10/100/1000 Mbit
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
8 ethernet port status LEDs (green, SoC controlled)
* Buttons: 1 on-off glide switch at the back (not configurable)
1 reset button at the right side, behind the air-vent
(not configurable)
1 reset button on front panel (configurable)
* Power 12V 1A barrel connector
* UART: 1 serial header (JP2) with populated standard pin connector on
the left side of the PCB, towards the back. Pins are labelled:
+ VCC (3.3V)
+ TX (really RX)
+ RX (really TX)
+ GND
the labelling is done from the usb2serial connector's point of
view, so RX/ TX are mixed up.
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
Instructions are identical to those for the GS1900-10HP and GS1900-8HP.
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-10HP is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only boot off the first partition anyway (hardcoded in the DTS). To
make sure we are manipulating the first partition, issue the following
commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-generic-zyxel_gs1900-8-squashfs-sysupgrade.bin
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds experimental ethernet support for BCM6318, BCM6328, BCM6362, BCM6368
and BCM63268.
BCM6358 needs a different driver, so there's no support for now.
Working devices:
- Comtrend AR-5315u
- Comtrend AR-5387un
- Comtrend VR-3025u
- Comtrend VR-3032u
Not working devices:
- Netgear DGND3700 v2 (no idea on how the external switch is connected)
- Huawei HG556a ver B (BCM6358 needs a separate driveer)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Make some cosmetic changes in the Buffalo LinkStation LS421DE NAS:
- Delete pointless #xxx-cells
- bootargs: replace earlyprintk with earlycon and remove unneeded args.
- Separate pinmux nodes with empty lines.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
dd on Mac OS X apparently fails when using 'M' unit for bs.
dd: bs: illegal numeric value
Use 'k' unit instead for 'pad-to' to fix that.
Reported-by: Georgi Valkov <gvalkov@abv.bg>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It's meant to provide upstream support for mtd & NVMEM. It's required
e.g. for reading MAC address from mtd partition content. It seems to be
in a final shape so it's worth testing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
NVRAM access may be needed early in boot process. Reading it using mtd
happens quite late in the init process. Add NVRAM initialization to the
NVMEM driver which comes up early and depends on IO mapping only.
This is required by Linksys devices which use NVRAM content for proper
partitioning (detecting current firmware partition).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Demote a number of debugging printk's to pr_debug to avoid log
nosie. Several of these functions are called as a result of
userspace activity. This can cause a lot of log noise when
userspace does periodic polling.
Most of this could probably be removed completely, but let's
keep it for now since these drivers are still in development.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
It supports NVRAM access described using DT binding. Right now NVRAM
data is exposed using /sys/bus/nvmem/ only.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Introduce new patch for automatically detecting RAM size.
Some boards have a different amount of RAM depending on the HW revision.
Therefore, automatically detecting the RAM size instead of hard-coding it will
reduce the number of device definitions.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Sercomm AD1018 has a NAND flash. We recently added support for NANDs
in this target.
Use the internal NAND as additional storage.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
This was added recently and thus overlooked in 85b1f4d8ca
("treewide: remove execute bit and shebang from board.d files").
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The bootloader of many ipq806x boards seems to require the config node
of the FIT image to be 'config@1' (or a secific different value).
This requirement used to be implicitely satisfied because OpenWrt used
to also call the configuration node inside a FIT image 'config@1'.
However, as recent U-Boot now prohibits the use of the '@' symbol as
part of node names, this was changed by
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Explicitely restore the default name of the configuration node to
'config@1' on ipq806x.
(ipq807x is unaffected as DEVICE_DTS_CONFIG default is set
"config@hk01" in target/linux/ipq807x/image/Makefile)
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The bootloader of many ipq40xx boards seems to require the config node
of the FIT image to be 'config@1' (or a secific different value).
This requirement used to be implicitely satisfied because OpenWrt used
to also call the configuration node inside a FIT image 'config@1'.
However, as recent U-Boot now prohibits the use of the '@' symbol as
part of node names, this was changed by
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Explicitely restore the default name of the configuration node to
'config@1' on ipq40xx.
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The in-SoC RTC of the Bananapi R64 is more disruptive than useful
without a battery connected. Disable it to not have Linux use the
RTC provided time 2000-01-01 00:00:00 after power-loss.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make packages depending on usb-serial selective, so we do not have
to add kmod-usb-serial manually for every device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Enable testing kernel.
Fix compile errors by using new kernel APIs.
Fix fuzz by manually editing patches to ensure the code goes in the
right place.
For 721-NET-no-auto-carrier-off-support.patch, revert upstream commit
a307593a6 to keep the OpenWrt ralink driver operational.
Add mt7621-pci-phy patch to select REGMAP_MMIO as discussed in PR #3693
and #3952.
Run automatic quilt refresh on the rest.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
0098-disable_cm.patch is not needed because upstream fixed CM handling.
The rest are straightforward removals of upstreamed patches.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
This reverts commit b4aad29a1d.
This was accidentally folded into a single commit. Remove it and
apply it properly again.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
It appears to be an automatic Kconfig symbol that varies depending on
the host platform. There is no need to define it in target configs, so
filter it out.
Also sort config-filter entries alphabetically.
Cc: Adrian Schmutzler <mail@adrianschmutzler.de>
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Enable testing kernel.
Delete upstreamed patches:
0098-disable_cm.patch can be dropped, upstream fixed CM handling.
Fix compile errors by using new kernel APIs.
Fix fuzz by manually editing patches to ensure the code goes in the
right place.
For 721-NET-no-auto-carrier-off-support.patch, revert upstream commit
a307593a6 to keep the OpenWrt ralink driver operational.
Add mt7621-pci-phy patch to select REGMAP_MMIO as discussed in PR #3693
and #3952.
Rename patches to follow the 3-digit classification from the OpenWrt
Developer Guide.
Run automatic quilt refresh.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
This patch copies over refreshed patches from 5.4.
- dropped crypto patches (they got upstreamed)
- dropped renesas USB 3 firmware loader (they got upstreamed)
- NAND now needs extra device-properties for ECC settings.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Also add a new kconfig symbol (CONFIG_KCMP) to the generic config,
disabling the SYS_kcmp syscall (it was split from
CONFIG_CHECKPOINT_RESTORE, which is disabled by default, so the
previous behaviour is kept).
Removed (upstreamed) patches:
070-net-icmp-pass-zeroed-opts-from-icmp-v6-_ndo_send-bef.patch
081-wireguard-device-do-not-generate-ICMP-for-non-IP-pac.patch
082-wireguard-queueing-get-rid-of-per-peer-ring-buffers.patch
083-wireguard-kconfig-use-arm-chacha-even-with-no-neon.patch
830-v5.12-0002-usb-serial-option-update-interface-mapping-for-ZTE-P685M.patch
Manually rebased patches:
313-helios4-dts-status-led-alias.patch
104-powerpc-mpc85xx-change-P2020RDB-dts-file-for-OpenWRT.patch
Run tested:
ath79 (TL-WDR3600)
mvebu (Turris Omnia)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
It's a BCM4906 based device (2 CPU cores). It has 512 MiB of RAM, 4 LAN
ports, 1 WAN port, 2 USB ports, NAND flash. WiFi unknown at this point.
Flashing is possible using CFE only, proper image will be worked on
later.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
From the original commit message:
"With GCC 10, building usbip triggers error for multiple definition
of 'udev_context', in:
- libsrc/vhci_driver.c:18 and
- libsrc/usbip_host_common.c:27.
Declare as extern the definition in libsrc/usbip_host_common.c."
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
