From driver point of view no differance between rtl8367b and rtl8367s
if it connected through EXT2 (rgmii only).
So this trivial patch add some identification and initialization only.
SGMII/HSGMII mode for EXT1 is not implemented for the sake of patch
clairity.
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
[Fix code format]
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[add flags to separate chip_num/chip_id detection; drop error print in
rtl8367b_init_regs, drop unnecessary info prints, code style fixes]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[rebase; use MII macros]
Signed-off-by: Gaspare Bruno <gaspare@anlix.io>
[code optimization]
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Set root=/dev/fit0 cmdline parameter as the kernel won't mount rootfs
otherwise after the change from the FIT partition parser to the fitblk
driver which replaces it.
Fixes: 6368ed1ae5 ("mediatek: mt7623: phase out uImage.FIT partition parser")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kernel warns about comparision of different types without cast when
building the fitblk driver on 32-bit platforms.
Fix this by using `min_t(size_t, ...`.
Fixes: 8fc5457869 ("kernel: add pending fitblk uImage.FIT sub-image block driver")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use the new fitblk driver on the BananaPi R2 as well as UniElec U7623.
Introduce boot device selection for fitblk's /chosen/rootdisk
handle, similar to how it is already done on MT7622, MT7986 and MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The default environment for the Linksys E8450 and Belkin RT3200 got
truncated by one line due to a broken patch. While the impact was
luckily only cosmetic, fix it so bootmenu title also shows U-Boot
version again.
Fixes: 6aec3c7b5b ("mediatek: mt7622: modernize Linksys E8450 / Belkin RT3200 UBI build")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
**Netgear LBR20** is a router with two gigabit ethernets , three wifi radios and integrated LTE cat.18 modem.
SoC Type: Qualcomm IPQ4019
RAM: 512 MiB
Flash: 256 MiB , SLC NAND, 2 Gbit (Macronix MX30LF2G18AC)
Bootloader: U-Boot
Modem: LTE CAT.18 Quectel EG-18EA , Max. 1.2Gbps downlink / 150Mbps uplink
WiFi class AC2200:
- radio0 : 5G on QCA9888 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps , 80MHz - limited for low channels
- radio1: 2,4G on IPQ4019 ,WiFi4- 802.11b/g/n MIMO2x2 300Mbps 40Mhz
- radio2: 5G on IPQ4019 , WiFi5- 802.11a/n/ac MU-MIMO 2x2 , 887Mbps ,80Mhz - limited for high channels (from 100 up to 165) . Becouse of DFS remember to set country before turning on.
Ethernet: 2x1GbE (WAN/LAN1, LAN2)
LEDs: section power : green and red , section on top (orbi) drived by TLC59208F: red, green ,blue and white
USB ports: No
Buttons: 2 Reset and SYNC(WPS)
Power: 12 VDC, 2,5 A
Connector type: Barrel
OpenWRT Installation
1. Simplest way is just do upgrade from webpage with *factory.img
2. You can also do it with standard tool for Netgear's debricking - NMPRFlash
3. Most advanced way is to open device , connect to UART console and :
- Prepare OpenWrt initramfs image in TFTP server root (server IP 192.168.1.10)
- Connect serial console (115200,8n1) to UART connector
- Connect TFTP server to RJ-45 port
- Stop in u-Boot and run u-Boot command:
> setenv serverip 192.168.1.10
> set fdt_high 0x85000000
> tftpboot 0x83000000 openwrt-ipq40xx-generic-netgear_lbr20-initramfs-zImage.itb
> bootm 0x83000000
- Login via ssh
- upload or download *sysupgrade.bin ( like wget ... or scp transfer)
- Install image via "sysupgrade -n" (like “sysupgrade -n /tmp/openwrt-ipq40xx-generic-netgear_lbr20-squashfs-sysupgrade.bin”)
Back to Stock
- Download firmware from official Netgear's webpage , it will be *.img file after decompressing.
- Use NMRPFlash tool ( detailed insructions on project page https://github.com/jclehner/nmrpflash )
Open the case
- Unscrew nuts and remove washers from antenna's conectors.
- There are two Torx T10 screws under the label next to antenna conectors. You have to unglue this label from left and right corner to get it
- Two parts of shell covers will slide out from eachother , you have to unglue two small rubber pads and namplate sticker on bottom to do that.
- PCB is screwed with 4Pcs of Torx T10 screws
- Before lifting up PCB remove pigtiles for LTE antennas and release them from PCB and radiator (black and white wires)
- On other side of PCB ,in left bottom corner there is already soldered with 4 pins UART connector for console. Counting from left it is +3,3V , TX , RX ,GND (reffer to this picture: https://i.ibb.co/Pmrf9KB/20240116-103524.jpg )
BDF's files are in firmware_qca-wireless https://github.com/openwrt/firmware_qca-wireless/ and in parallel sent to ath10k@lists.infradead.org.
Signed-off-by: Marcin Gajda <mgajda@o2.pl>
Replace ARM bootloader patch with pending upstream version. The patch
got reviewed upstream and tested on a Netgear R7800.
This fix a problem with the ARM decompressor and permits to use
AUTO_ZRELADDR without having to hardcode PHYS_OFFSET as the bootloader
now correctly parse the memory modes in the appended DTB.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit c42b915af0.
Now that rpcd uses the 'Auto-Installed' field to differentiate between
deliberately and implicitely installed packages we can remove the
hotfix.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All mt7622 board previously using the FIT partition parser have been
converted to use the fitblk driver:
6aec3c7b5b mediatek: mt7622: modernize Linksys E8450 / Belkin RT3200 UBI build
41c053141e mediatek: mt7622: convert unifi6lr-v{1,2,3}-ubootmod to fitblk
208f6c1232 mediatek: mt7622: convert BPi-R64 to all-UBI layout and fitblk
Remove the now no longer needed FIT partition parser from builds for
mt7622.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use newly added support for NVMEM-on-UBI instead of extracting MAC
address and WiFi EEPROM data in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use newly added support for NVMEM-on-UBI instead of extracting MAC
address and WiFi EEPROM data in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use newly added support for NVMEM-on-UBI instead of extracting MAC
address and WiFi EEPROM data in userspace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It seems that ipq-wifi bump included and incorrect PKG_MIRROR_HASH value,
so fix it by using:
make package/firmware/ipq-wifi/check FIXUP=1
Fixes: 70fd815e57 ("qualcommax: ipq807x: add support for Linksys MX5300")
Signed-off-by: Robert Marko <robimarko@gmail.com>
When both variants of ath10k drivers are selected, any driver that is
selected along is being built twice, one for each ath10k variant.
Avoid these redundant builds by introducing an optional second parameter
to config_package that lists the variants for which the package is to be
built.
If the symbol is to be set for all of the variants, $(ALL_VARIANTS) can
be used. This is the case for the mac80211 and cfg80211 modules. If
the parameter is empty, then the module will be selected and thus built
when the first variant is compiled.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Having different build directories is the default when the package
Makefile defines more than one variant.
Mac80211 overrides PKG_BUILD_DIR, not taking different variants in
consideration, which causes clobbering the directories when both
variants are built.
When compiled with AUTOREMOVE=y, the effect is that the package is
unnecessarily rebuilt when the package is compiled again.
Wihout AUTOREMOVE, the problem is worse: the second variant will not be
rebuilt, and you end up with the smallbuffers variant being a copy of
the regular one.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Add node to support the QUP4 SPI controller inside of IPQ8074.
Some devices use this bus to communicate to a Bluetooth controller.
Signed-off-by: Robert Marko <robimarko@gmail.com>
add back WIFI eprom addresses pointer in mt7621_dlink_dir-xx60-a1.dtsi
Change MAC address pointer from factory_e006 to factory_e000 + 3
same as used in D-link firmware 1.11 DIR-1960-A1
DIR-1960-A1,DIR-2640-A1,DIR-2660-A1,DIR-3060-A1
Clean-up MAC addresses in D-Link NOR devices DTS's
Change WIFI MAC Addressees to the same as NAND cousins macaddr_factory_e000 + ?
as later devices don't have the MAC address in factory configuration
same as used in D-Link firmware 1.30 DIR-878-A1
DIR-867-A1,DIR-878-A1,DIR-878-R1,DIR-882-A1,DIR-882-R1,DIR-1935-A1
* D-link software differs between source of wan address
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
Usage of word "add" was somehow misleading in those functions:
1. They don't really add (as in: append) anything. Result files are
created from scratch.
2. It wasn't clear what adding files means. It could be understood as
adding actual files somewhere (to existing archive?).
Also the word "add" was also a bit ambiguous.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rename function to more accurate and self-explanatory name:
1. Use "archive" in name as this functions creates tar archive
2. Avoid "conffiles" as this function may archive more than that
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This reverts commit 4fa9aaf0be.
That seemed like a good idea allowing us to include any runtime
generated file in archive. Unfortuantely it broke backups with files
from mounted directories.
When mounting overlay with / as lowerdir its mounts don't propagete in
the mountpoint. That resulted in empty directories:
/tmp/overlay.XXXXXX/backup/tmp/
/tmp/overlay.XXXXXX/backup/var/
/tmp/overlay.XXXXXX/backup/dev/
/tmp/overlay.XXXXXX/backup/proc/
etc.
As some platforms / users try to backup files like /var/dhcp.leases or
/boot/cmdline.txt it means we can't use that solution.
Link: http://lists.openwrt.org/pipermail/openwrt-devel/2024-February/042320.html
Link: https://lore.kernel.org/linux-fsdevel/67bb0571-a6e0-44ea-9ab6-91c267d0642f@gmail.com/T/#u
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This reverts commit bf304d10e9.
That uci-defaults script worked great but generating it required
mounting root dir as overlay lowerdir that needs to be reverted.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
With mac80211_hwsim I have seen such entries in OpenWrt 22.03:
HE Iftypes: managed, AP
The mac80211.sh script did not detect the entry and failed. Allow
arbitrary other entries before to fix this problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now we support parsing the color and function properties.
Ref: e814acc599 ("base-files: support parse DT LED color and function")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
In some situations (slow protocol or interfaces with auto 0), the
interfaces are not available during the dnsmasq initialization and
hence, the ignore setting will be skipped.
Install an interface trigger for ignored interfaces in case their
ifname cannot be resolved.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
[bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When QCA8072 is used in PSGMII mode with IPQ6018, PCS used for second
PHY port would overlap with one used by SGMII+ port. SoC has register
to select different PCS in such case.
Original code used PHY_ID for this decision, which also had other
issues, but is no longer viable since we moved to upstream QCA807x
driver.
Introduce DT property port3_pcs_channel to allow describing this in DT.
Default value is <2>, and for some QCA8072 designs <4> would be needed.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
[port 8ed390a (qualcommax: set correct PHY mode for port 0-4) to ipq60xx]
Port 0-4 have the mode set to SGMII instead of PSGMII. Now that we use
he upstream qca807x driver, this conflicts with the qca SSDK driver
that expects the mode to be PSGMII as for not integrated driver, it does
refer to the real PHY mode.
Update the entry for port 0-4 to PSGMII to solve warning from qca SSDK
in ipq6018-ess.dtsi.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Hardware
--------
RockChip RK3566 ARM64 (4 cores)
- up to 8GB LPDDR4X
- 1x HDMI,
- 2x MIPI DSI
- 2x MIPI CSI2
- 1x eDP
- 1x PCIe card
- 2x SATA
- 2x USB 2.0 Host
- 1x USB 3.0
- 1x USB 2.0 OTG
- 10/100/1000 Base-T
- microSD slot
- 40-pin GPIO expansion header
- 12V DC
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
