Upstream hwmon-maintainer had various comments about
the changes to the tc654 driver. These have been
addressed and the cooling device support is destined
for inclusion.
One of the comments was the change of the cooling states
scaling. No longer the driver uses the same values as the
hwmon interface, instead the states are now the 17 states
the tc654 supports.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
with the introduction of the DEVICE_ALTX_VENDOR, DEVICE_ALTX_MODEL
multiple/sibiling devices can seemingly supported by one device entry.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
the WNDR4700 can fetch its calibration data and
mac-addresses directly from the "wifi_data" partition.
This allows us to get rid of the 10-ath9k-eeprom file
for the apm821xx target completely.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
in order to get nvmem-cells to work on AP and routers
(Netgears WNDR4700). The nvmem-cell needs to be within
a fixed-partition dt-node.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add and enable a new kconfig knob to disable unprivileged eBPF by default.
Patches automatically rebased.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
These never worked and upstream is in the process of removing
them as well. Legacy PCI interrupt signaling is still working
as before.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Apart from the dtb partition, these were all "read-only;"
they serve no purpose other than being a copy of what
netgear had defined in their original firmware.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
where to begin? the USB regulator settings were just
a part of the issue. With them changed, according to
the forum it still failed when a USB device was
connected to the port with:
dwc2 4bff80000.usbotg: dwc2_restore_global_registers: no global registers to restore
dwc2 4bff80000.usbotg: dwc2_exit_partial_power_down: failed to restore registers
dwc2 4bff80000.usbotg: exit partial_power_down failed
dwc2 4bff80000.usbotg: HC died; cleaning up
One clue was found upstream in
commit cc10ce0c51b1 ("usb: dwc2: disable power_down on Amlogic devices")
|Disable power_down by setting the parameter to
|DWC2_POWER_DOWN_PARAM_NONE. This fixes a problem on various Amlogic
|Meson SoCs where USB devices are only recognized when plugged in before
|booting Linux. A hot-plugged USB device was not detected even though the
|device got power (my USB thumb drive for example has an LED which lit
|up).
|[...]
the same method proposed there worked with APM821xx's USB IP-Core.
Link: https://forum.openwrt.org/t/wd-my-book-duo-usb/111926/2
Reported-by: thwe and takimata (openwrt forum)
Fixes: b70d3557e0 ("apm821xx: clean up gpio-hogs")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2
either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.
CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
This patch changes the default network configuration
to fetch the IP addresses over dhcp instead of being
statically assigned.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch [1]
Manually rebased:
bcm27xx/patches-5.10/950-0355-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
Note: although automatically rebaseable, the last patch has been edited to avoid
conflicting bit definitions.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=b6f32897af190d4716412e156ee0abcc16e4f1e5
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
This should have been included in the previous patch that
resized the kernel partition to fit bigger kernels.
Fixes: 7a6a349445 ("apm821xx: WNDAP620 + WNDAP660: reorganize partitions for 5.10")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch updates all current APM82181 devices over to that
"new LED naming scheme". This includes many updates to the
device-tree:
- dropped the deprecated, but beloved "label" property.
- rename all DT leds node names to led-#.
- add function and color properties.
- utilized panic-indicator property.
- dropped led- aliases (see below).
migration scripts for all devices are included.
For more information. See:
<https://www.kernel.org/doc/html/latest/leds/leds-class.html>
For the future: It looks like the color+function properties
won over the dt-alias / label. This will need to be wired up
into openwrt eventually. For APM821xx the situation is that
all devices have a dedicated power and fault indicator.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The MX60's kernel is limited to 0x3EFC00 by the values in
mkmerakifw.c. Since the initramfs method of loading the
kernel seems to be working, this patch does away with the
use of the mkmerakifw tool for the MX60(W).
But this will go along with a change in u-boot as well.
So before you upgrade, please attach the serial cable and
perform:
| setenv owrt510_boot run meraki_ubi owrt_bootargs\; run owrt_load1 owrt_bootkernel\; run owrt_load2 owrt_bootkernel
| setenv bootcmd run owrt510_boot
| saveenv
Note: You won't be able to use older OpenWrt releases without
switching the bootcmd back to owrt_boot!
Note2: We are no longer compatible with older OpenWrt MX60 installs.
the legacy BOARD_NAME and SUPPORTED_DEVICES can be dropped. This is
because upgrades from older images are not possible without uboot env
changes anymore. Also the bogus BLOCKSIZE value
(which was set to 63k back then, in order to get the kernel properly
aligned after the fdt + meraki header) can be set to the NANDs real
value. The FDT size (which was needed for alignment) can now be
slimmed down as well.
Co-developed-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Takimata reported on the OpenWrt forum in thread [0], that his
MyBook Live Duo wasn't booting OpenWrt 21.02 after upgrading
from the previous OpenWrt 19.07.
The last logged entries on his console
|[ 0.531599] sata1-regulator GPIO handle specifies active low - ignored
|[ 0.538391] sata0-regulator GPIO handle specifies active low - ignored
|[ 0.759791] ata2: SATA link down (SStatus 0 SControl 300)
|[ 0.765251] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
|[ 5.909555] ata1.00: qc timeout (cmd 0xec)
|[ 5.913656] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
|[ 6.231757] ata1: SATA link down (SStatus 0 SControl 300)
This extract clearly showed that the HDD on which OpenWrt is installed,
simply disappeared after the SATA power regulators had been initialized.
The reason why this worked with OpenWrt 19.07 was because the kernel
config symbol CONFIG_REGULATOR=y was not set in the target's config-4.14.
(This shows that the MBL Single does differ from the DUO in that
it does not have programmable power regulators for the HDDs.)
[0] <https://forum.openwrt.org/t/21-02-0-and-snapshot-fail-to-boot-on-my-book-live-duo/106585>
Reported-by: Takimata (forum)
Tested-by: Takimata (forum)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
try to reduce the kernel size by disabling and moving
options from the common kernel configuration to the
SATA target that doesn't have the constraints.
For NAND this has become necessary because as with 5.10
some devices outgrew their kernels. Though, in my tests
this didn't help much: just a smidgen over 100kib was
saved on the uncompressed kernel.
... running make kernel_oldconfig also removed some
other config symbols, mostly those that already set
from elsewhere or became obsolete in the meantime.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
disables the MX60(W) from being built by the builders for now.
But there's an effort to bring it back:
<https://github.com/openwrt/openwrt/pull/4617>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Due to 5.10 increased kernel size, the current 4MiB-ish kernel
partition got too small. Luckily, netgear's uboot environment
is setup to read 0x60000 bytes from the kernel partition location.
... While at it: also do some cleanups in the DTS in there.
The original (re-)installation described in
commit d82d84694e ("apm821xx: add support for the Netgear WNDAP620 and WNDAP660")
seemed to be still working for now. What I noticed though
is that the bigger initramfs images needed to use a different
destination address (1000000) to prevent it overwriting
itself during decompression. i.e:
# tftp 1000000 openwrt-...-wndap620-initramfs-kernel.bin
# bootm
However, in case of the WNDAP620+660 the factory.img image can be
written directly to the flash through uboot.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Both NAND and SATA targets need the DMA engine in one way
or another.
Due to a kernel config refresh various existing symbols
got removed from the apm821xx main config file as well.
(That being said, they are still included because the
built-in crpyto4xx depends on these.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This moves CONFIG_REGULATOR to the target config instead of the
subtarget config.
For kernel 5.10, CONFIG_AT803X_PHY depends on CONFIG_REGULATOR.
As we do not have a size constraint, move this symbol to the
target configuration for kernel 5.4 as well as 5.10.
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: David Bauer <mail@david-bauer.net>
The previous config will only show 2.4G radio activity status
This change mr24:green:wifi4 and mr24:green:wifi2 to
show 2.4G and 5G radio on and off status
change mr24:green:wifi3 and mr24:green:wifi1 to
show 2.4G and 5G radio activity status
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
Removed upstreamed:
generic/pending-5.4/770-02-net-ethernet-mtk_eth_soc-fix-rx-vlan-offload.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800
Note that since I rebased the previous commit, I removed my Run-tested line
although I confirm building the image successfully.
Signed-off-by: John Audia <graysky@archlinux.us>
This came up in an upstream commit: "
b1dd9bf688b0 "net: phy: broadcom: Fix RGMII delays for BCM50160 and BCM50610M"
The PHY driver entry for BCM50160 and BCM50610M calls
bcm54xx_config_init() but does not call bcm54xx_config_clock_delay() in
order to configuration appropriate clock delays on the PHY, fix that."
So the "rgmii" phy-mode has always been wrong, but went unnoticed since
the broadcom phy driver didn't push the delay settings to the chip.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Straightforward refresh of patches using update_kernel.
Run tested: x86_64 (apu2)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Manually rebased:
bcm27xx/950-0993-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
layerscape/701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[remove accidental whitespace edit]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch copies over refreshed patches from 5.4.
- dropped crypto patches (they got upstreamed)
- dropped renesas USB 3 firmware loader (they got upstreamed)
- NAND now needs extra device-properties for ECC settings.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
