1. Import pending patch to fix ramips/mt7621 64MB targets.
2. Do not enable CONFIG_PAGE_POOL_STATS by default.
Signed-off-by: Danila Romanov <pervokur@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
XikeStor (Seeker) SKS8300-8X is a 8 ports Multi-Gig switch, based on
RTL9303.
Specification:
- SoC : Realtek RTL9303
- RAM : DDR3 512 MiB
- Flash : SPI-NOR 32 MiB (Winbond W25Q256JVFIQ)
- Ethernet : 8x 1/2.5/10 Gbps (SFP+)
- LEDs/Keys (GPIO): 1x/1x
- UART : "Console" port on the front panel
- type : RS-232C
- connector : RJ-45
- settings : 9600n8
- Watchdog : Diodes PT7A7514WE
- Power : 12 VDC, 2 A
Flash instruction using initramfs image:
1. Prepare TFTP server with an IP address "192.168.2.36"
2. Connect your PC to Port1 on SKS8300-8X
3. Power on SKS8300-8X and interrupt by Ctrl + B
4. Login to the vendor CLI by Ctrl + F and "diagshell_unipoe_env"
5. Login to the U-Boot CLI by "debug_unish_env" command
6. Enable Port1 with the following commands
rtk 10g 0 fiber1g (or fiber10g if 10GBase-*R)
rtk ext-devInit 0
rtk ext-pinSet 2 0
Note: the last command sets tx-disable to low
7. Download initramfs image from TFTP server
tftpboot 0x82000000 <image name>
8. Boot with the downloaded image
bootm
9. On the initramfs image, backup the stock firmware if needed
10. Upload (or download) sysupgrade image to the device
11. Erase "firmware" partition to cleanup JFFS2 of stock FW
mtd erase firmware
12. Perform sysupgrade with the sysupgrade image
13. Wait ~120 sec to complete flashing
Notes:
- A kernel binary "nos.img" needs to be stored into JFFS2 filesystem
using 4KiB erase block instead of 64KiB.
- PT7A7514WE is handled by hardware-assited system LED output
(blinking).
- Some Japanese users asked to XikeStor about maximum power limit of
SFP+ ports and got approximate criteria:
- per port : <= 2.9 W
- total (8 ports): <= 15.8 W
MAC addresses:
eth0 : 84:E5:D8:xx:xx:37 (board-info (stock:"flash_raw"), 0x218 (hex))
(ports): 84:E5:D8:xx:xx:36 (board-info (stock:"flash_raw"), 0x1f1 (hex))
Reverting to stock firmware:
1. Prepare OpenWrt SDK to use the mkfs.jffs2 tool contained in it
Note: the official mkfs.jffs2 tool in mtd-utils doesn't support 4KiB
erase size and not usable for SKS8300-8X
2. Create a directory for working
3. Download official firmware for SKS8300-8X from XikeStor's official
website
4. Rename the downloaded firmware to "nos.img" and place it to the
working directory
5. Create a JFFS2 filesystem binary with the working directory
/path/to/mkfs.jffs2 -p -b -U -v -e 4KiB -x lzma \
-o nos.img.jffs2 -d /path/to/working/dir/
6. Upload the created JFFS2 filesystem binary to the device
7. Erase the "firmware" partition
mtd erase firmware
8. Write the JFFS2 filesystem binary to the "firmware" partition
mtd write /path/to/nos.img.jffs2 firmware
9. After writing, reboot the device by power cycle
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17593
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Change some debugging messages of RTL930x SerDes in the PHY driver to
pr_debug() to suppress log messages on the console.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17593
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Add aux-mdio and pinctrl nodes to rtl930x.dtsi to enable handling of the
external RTL8231 GPIO expander connected via MDIO.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17593
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Enable HIGHMEM option to use all ranges of memory on XikeStor SKS8300-8X
that has 512MiB RAM.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17593
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Now, that initramfs images built for ZTE devices work, by moving
LZMA_TEXT_START further up the available RAM - same fix works
successfully for Meraki MR18 too. Apply it and reenable initramfs
generation again.
Fixes: 1d49310fdb5e ("ath79: add Cisco Meraki MR18")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17680
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit fixes Xiaomi AX3000t soft bricks. Issue affects at least rd23
model (Global version) users:
Link: https://forum.openwrt.org/t/openwrt-support-for-xiaomi-ax3000t/180490/452
I also found that these nvram settings are wrong for the rd23 model and
U-Boot erase them:
'''
flag_try_sys1_failed 8
flag_try_sys2_failed 8
'''
As a result, platform.sh -> xiaomi_initial_setup() function sometimes ends
early without applying settings for the rd23 model.
RD03 model strategy:
1. Don't touch values those were set up by platform.sh ->
xiaomi_initial_setup() function
RD23 model strategy:
1. Apply correct nvram settings at every boot
2. Use bulk fw_setenv call
I didn't find opened issue for AX3000t. Similar AX3200 issue:
Link: https://github.com/openwrt/openwrt/issues/16347
So, other Xiaomi devices (e.g. Xiaomi WR30U) may also require fix.
Fixes: 7dbcc1215a56cc1da68c81bf92d7efa174c5e051 ("mediatek: filogic: add support for Xiaomi AX3000T")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17580
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit replaces multiple fw_setenv calls by the bulk one to reduce
flash writes.
Thanks @Linaro1985 for the idea.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17580
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
the CWMP account mac is correctly set on the lan device but was not correctly as label-mac
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17618
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These symbols are needed to satisfy lxc dependencies.
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17553
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ruckus R500 datasheet: https://webresources.ruckuswireless.com/datasheets/r500/ds-ruckus-r500.html
Specifications:
SoC: 720Mhz QCA9558
RAM: 256MB
Storage: 64MB of FLASH (SPI NOR - S25FL512S)
1x AR8327 GB switch
Ethernet: 1x1000M port #3 on AR8327,
1x1000M (802.3at POE), port #5 on AR8327
Wireless: QCA988X HW2.0 802.11ac
AR9550 2.4GHz 802.11b/g/n
5x GPIO LED
1x GPIO Reset Button
1x DC Jack 12v
1x UART, 3.3v, 115200
1x TPM, SLB9645TT12
2x Beamforming antennas configured via 74LV164
MAC addresses:
1. art 0x807E | Factory bridged | f0:3e:90:XX:XX:80 |
2. art 0x66 | eth0 | f0:3e:90:XX:XX:83 | (port 5, cpu port 6) - PoE port
3. art 0x6c | eth1 | f0:3e:90:XX:XX:84 | (port 3, cpu port 0) - non PoE port
Serial console: 115200-8-N-1 on internal H4 header.
Pinout:
H1
-----------
|1|x|3|4|5|
-----------
Pin 1 is near the "H4" marking.
1 - RX
x - no pin
3 - VCC (3.3V)
4 - GND
5 - TX
JTAG: Connector H2, similar to MIPS eJTAG, standard, unpoulated.
H9
----------------------
|2 |4 |6 |8 |10|12|14|
----------------------
|1 |3 |5 |7 |9 |11|13|
----------------------
3 - TDI
5 - TDO
7 - TMS
9 - TCK
2,4,6,8,10 - GND
14 - Vref
1,11,12,13 - Not connected
I²C: connector H2, near power LED, unpopulated:
------
|1|2|3
------
H2
1 - SCL
2 - SDA
3 - GND
Installation:
Serial Port/TFTP
1. Setup tftp server on the local network
2. Connect to UART with TTL
3. Interupt U-boot process with Ctrl-C
4. Setup appropriate ipaddr and serverip in setenv:
- setenv ipaddr 192.168.1.1
- setenv serverip 192.168.1.2
5. On TFTP Server - copy openwrt-ath79-generic-ruckus_r500-initramfs-kernel.bin to /srv/tftp
6. On R500 boot into initrd image
- tftpboot 0x81000000 openwrt-ath79-generic-ruckus_r500-initramfs-kernel.bin
- bootm 0x81000000
7. On TFTP server - scp -O openwrt-ath79-generic-ruckus_r500-squashfs-sysupgrade.bin root@192.168.1.1:/tmp
8. Ensure the boot command is set before flashing the image:
fw_setenv bootcmd 'bootm 0xbf1c0000'
9. On R500 - sysupgrade /tmp/openwrt-ath79-generic-ruckus_r500-squashfs-sysupgrade.bin
10. If not done in 8; set boot command from U-boot shell itself:
- setenv bootcmd bootm 0xbf1c0000
- saveenv
- reset
This patch adapted from https://github.com/victhor393/openwrt-ruckus-r500/tree/ruckus-r500-master
Signed-off-by: Damien Mascord <tusker@tusker.org>
- Heavily refactored the device tree
- Extended commit message
- Documented onboad connectors
- Refactored MAC and calibration data setups to use nvmem-layout
- Made both network interfaces LAN ports and bridge them, this makes
more sense for an access point and is consistent with the rest of
Ruckus APs.
- Enable lzma-loader for compressed initramfs
- Enabled the optional internal USB port
- Added missing LEDs and according pinctrl settings
- Added reserved memory region used for bootloader communication
- Added the bit-banged I²C bus and onboard TPM
- Refactored boot scheme and flash layout to match earlier Ruckus
devices and maximize usable space for user data.
Quirks:
- H7 is the physical presence switch for the SLB9645TT12 TPM.
TODO:
- Link state reporting on the Ethernet ports doesn't work and both ports
report "up" due to limitation of swconfig ar8327 driver. With DSA
conversion, this shall be rectified.
- Locate 2nd shift register (U7) controlling beamforming antennas, probably
on ath10k GPIOs which are currently unsupported in the driver. For
this, there is a device tree node describing that - but explicitly
disabled.
- At the moment of adding support, there is an endianness bug in the TPM
driver causing it to not detect the TPM module because of ID mismatch.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
047b2efc1348 CMakeLists.txt: bump minimum cmake version
16ff0badbde7 CMakeLists: add support for including ABIVERSION in the library version number
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There is currently a problem where the rootfs in an initramfs image for
single target build is not updated on subsequent run. This is caused by
a bug introduced in d78dec3e19e3 ("kernel: copy kernel build dir on
Per-Device Initramfs compilation") where the initramfs_data.cpio rm was
moved to PrepareConfigPerRootfs. This caused the side effect of dropping
the rm call for single target build making the kernel reusing the
previous generated initramfs_data.cpio.
To correctly handle this, restore the original location of this call
right after the touch /init call. This way the kernel will always
regenerate the initramfs embedded rootfs ALSO for single target build.
Fixes: d78dec3e19e3 ("kernel: copy kernel build dir on Per-Device Initramfs compilation")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Increase PKG_RELEASE as follow-up for
("lantiq: fritz_cal_extract with reverse option for AVM FritzBox 7430").
Signed-off-by: Robert Marko <robimarko@gmail.com>
This implementation of fritz_cal_extract can also retrieve firmware
data stored in reverse byte order, as found in the AVM 7430 device.
This is done by intermediate storage in a buffer presumably large enough
to hold the complete data set. Currently, this buffer size is 128kB + 1kB
(some extra space for skipped data).
In the usual case of "forward" data, this implementation should behave
like the original implementation in all common cases. limit [-l] will
determine the amount of data read and size of buffer allocated.
However, if you are reading reversed data or didn't set a limit, the buffer
may be too small to hold all data. In this case, you can choose a higher
limit [-l] to enforce a sufficient buffer size.
Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
Link: https://github.com/openwrt/openwrt/pull/15501
Signed-off-by: Robert Marko <robimarko@gmail.com>
The image size has been changed to prevent failures in routers and bootloop
when flashing a large image using a stock bootloader. The LED trigger
package has been removed for 1910, which is no longer in use.
Signed-off-by: Anton Yu. Ivanusev <ivanusevanton@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/17630
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Define EX5601-T1 and T-56 as alternative name, to explicitly show
the device is supported using existing image. EX5601-T1 does not
have the option to switch between WAN/SFP port. The switch port
is hardwired to the WAN port. The Zyxel T-56 is the odido-branded
version of the EX5601-T1.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17615
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that LZMA_TEXT_START is configurable per-target once again,
move the target above 32MB boundary for ZTE MF28* devices.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17616
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
initramfs for some devices grew so big, that it can't be loaded within
the previous 32MB RAM limit. Make the LZMA_TEXT_ADDRESS configurable
per-target once again, to fix it for bigger devices, while maintaining
compatibility with previous ones.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17616
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Version 6.11 - October 8, 2024
* Feature: cmis: print active and inactive firmware versions
* Feature: flash transceiver module firmware (--flash-module-firmware)
* Feature: add T1BRR 10Mb/s mode to link mode tables
* Feature: support for disabling netlink from command line
* Fix: fix lanes parameter format specifier
* Fix: add missing clause 33 PSE manual description
* Fix: qsf: Better handling of Page A2h netlink read failure
* Fix: rss: retrieve ring count using ETHTOOL_GRXRINGS ioctl (-x)
* Misc: man page formatting fix
* changelog here: https://git.kernel.org/pub/scm/network/ethtool/ethtool.git/commit/NEWS?id=c0ea4b70c71334ef038f7a3416b228a50dada406
Tested on gl.inet MT6000, retrieve ring count is now working
Signed-off-by: Andrea Pesaresi <andreapesaresi82@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17607
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update handling of macro __assign_str() to also support the one-argument
variant when building against kernel 6.10 or later. This is needed for
building the next LTS kernel 6.12.
Fixes: 384d079fd8 ("mac80211: update to version 6.11")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/17456
Signed-off-by: Robert Marko <robimarko@gmail.com>
As per @KanjiMonster comment: st1202_dt_init() calls devm_led_classdev_register_ext() before the internal data structures are properly setup, so the leds become visible to user space while being partially initialized, leading to a window where trying to access them causes a NULL pointer access.
Move devm_led_classdev_register_ext() to the last thing to happen during initialization.
Signed-off-by: Manuel Fombuena <fombuena@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17543
Signed-off-by: Robert Marko <robimarko@gmail.com>
The WAX220 does have a 2.4GHz and 5GHz wifi led, which was set to trigger on netdev before.
This commit changes this to trigger on activity of the respective radio
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17627
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix the name used for the transition image from Cudy.
This should make it possible to use the cudy transition image.
Fixes: 9d66b8b312fb ("mediatek: filogic: Add support for cudy wr3000h")
Link: https://github.com/openwrt/openwrt/pull/17652
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some VRX518 modems fail to initialize properly with the error message
"dc_ep_clk_on failed". As a result, the DSL data path doesn't work.
This hack, which is based on code from the FRITZ!Box 7530 GPL archive,
fixes the issue. It changes the PCIe vendor/device ID to values matching
a Lantiq SoC. It also appears to emulate a Lantiq CPU ID register for
connected PCIe devices, by remapping the matching address area to a
specially crafted buffer using the address translation unit.
A dedicated compatible is created to activate this in
the device tree, so this shouldn't affect any devices other than
FRITZ!Box 7530/7520.
Original investigation was done in 59f5212517 which used the "avm,host_magic" property to enabled the patch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17622
Signed-off-by: Robert Marko <robimarko@gmail.com>
According to datasheet, on AR9344 the switch and switch analog need to
be reset first before initiating a full reset.
Resetting these systems fixes spurious reset hangs on Atheros AR9344
SoCs.
Link: https://github.com/freifunk-gluon/gluon/issues/2904
Signed-off-by: David Bauer <mail@david-bauer.net>
This reverts commit 916af73fc388d638b1a717a2411792e0680dd8e6.
It was reported this change did not fix the reboot issues on AR9344.
Signed-off-by: David Bauer <mail@david-bauer.net>
Currently, 2.5G port LED-s on Dynalink are incorrectly configured and thus
they will light up all of the time.
So, lets fix this by:
1. Current green LED is actually yellow, change the color
2. Fix its polarity as its actually active-low
3. The yellow LED that was registered as being connected to LED_1 pin on
the PHY is not actually connected at all, so remove it.
4. The actual green LED is connected to LED_2 on the PHY so add it.
Fixes: 75ad5c24142a ("qualcommax: switch to qca8081 upstream PHY driver")
Fixes: #14502
Link: https://github.com/openwrt/openwrt/pull/17656
Signed-off-by: Robert Marko <robimarko@gmail.com>
Enable the RTL8231 MFD core driver, as well as the pinctrl/gpio driver
to allow RTL839x devices to use it.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Enable the driver for the Realtek Otto auxiliary MDIO driver so RTL839x
devices can use it. The related node is added to the base devicetree for
rtl839x-based devices, so they can enabled and use it when required.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
For RTL839x, the driver was producing frequent timeouts on bus accesses.
Increasing the timeout to the one from a recent Realtek SDK resolves
these timeouts. To minimize overhead on different SoCs, each controller
can specify their own timeout.
This also add support for the register format as used on RTL93xx.
Support is added for the RTL930x "ext gpio" controller.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The patch adding temperature sensor support for r8169 has been removed upstream
and the functionality will be added to Realtek PHY instead:
1f691a1fc4
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
