Airtime policy configuration is extremely useful in multiple BSS scenarios.
Since nowadays most people configure both private and guest networks (at
least), it makes sense to enable it by default, except for the most limited
of the variants.
Size of the hostapd-basic-openssl binary (mipsel 24Kc -O2):
543944 bytes (airtime policy disabled)
548040 bytes (airtime policy enabled)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
(cherry-picked from commit d38f456582)
netifd is responsible for handling that, except if the vlan bridge
was provided by the config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit cf45caeff1)
No functional changes, just some renames to make it easier to keep mt76 in
sync with upstream
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit e62c550470)
(cherry-picked from commit a889dcd3f2)
Required for an upcoming mt76 update
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 978e822db3)
(cherry-picked from commit af9d31aacc)
This is needed for an upcoming mt76 update
also sync iw nl80211 with kernel backports
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 2bfac61483)
(cherry-picked from commit 36019ed589)
Improves airtime fairness, especially for devices with larger firmware buffers
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit a5888ad6b3)
On systems using brmcfmac (e.g. Raspberry Pi Zero W) without this fix,
the final setup-call:
iw dev wlan0 ibss join ...
fails with returncode 161 and message:
"command failed: Not supported (-95)"
So this patch calls an explicit:
iw dev wlan0 set type ibss
just prior to the 'ibss join' command.
I have tested several ath9k and mt76xx devices
with different revisions: this patch does not harm.
please also apply to stable branch.
Signed-off-by: Bastian Bittorf <bb@npl.de>
(cherry-picked from commit ea5fce3f46)
In some cases, spurious failures might be cleared by teardown and retry
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 42dda0ed3e)
The channel offset used for VHT segment calculation was missing for HT
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit a0d81ba0d5)
Some drivers advertise it, but it's not supported at the moment
Reported-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 42a99b18ff)
The colon does not directly follow the "VHT Capabilities" string
Reported-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 3518b793a2)
Emit the new band option instead of hwmode
Support 6 GHz band and HE options
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 8504212f65)
Use it to look up frequencies only in the configured band to better deal
with channel number overlap
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 8b8c1cb09b)
This increases the size of the iw_5.9-8fab0c9e-3_mips_24kc.ipk from
41166 to 41942 bytes by 776 bytes.
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
(cherry-picked from commit 9df7eadcfd)
At least since gcc 7.3.0 (OpenWrt 18.06) lwr/lwl are used in the
assembly of LzmaProps_Decode. While the decission made by the compiler
looks perfect fine, it triggers some obscure hang on lantiq danube-s
v1.5 with MX29LV640EB NOR flash chips.
Only if the offset 1 is used, the hang can be observed. Using any other
offset works fine:
lwl s0,0(a1) - s0 == 0x6d000080
lwl s0,1(a1) - hangs
lwl s0,2(a1) - s0 == 0x0080xxxx
lwl s0,3(a1) - s0 == 0x80xxxxxx
It isn't clear whether it is a limitation of the flash chip, the EBU or
something else.
Force 8bit reads to prevent gcc optimizing the read with lwr/lwl
instructions.
Signed-off-by: Mathias Kresin <dev@kresin.me>
e983a25 Update regulatory rules for Ecuador (EC)
a0bcb88 wireless-regdb: Update regulatory rules for Norway (NO) on 6 and 60 GHz
cdf854d wireless-regdb: Update regulatory rules for Germany (DE) on 6GHz
86cba52 wireless-regdb: reduce bandwidth for 5730-5850 and 5850-5895 MHz in US
6fa2384 wireless-regdb: remove PTMP-ONLY from 5850-5895 MHz for US
9839e1e wireless-regdb: recent FCC report and order allows 5850-5895 immediately
42dfaf4 wireless-regdb: update 5725-5850 MHz rule for GB
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit dbb4c47798)
Per FHS 3.0, /var/lock is the location for lock files [1].
However its current permissions (755) are too restrictive
for use by unprivileged processes.
Debian and Ubuntu set them to 1777, and now so do we.
[1] <https://refspecs.linuxfoundation.org/FHS_3.0/fhs-3.0.html#varlockLockFiles>
Signed-off-by: Deomid Ryabkov <rojer@rojer.me>
[fixed typo in commit message, had to remove "rojer" due to git hooks]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 430f691943)
This enables building of rpcapd and adds it as a package.
It is a daemon that allows remote packet capturing from another machine.
E.g. Wireshark can talk to it using the Remote Capture Protocol (RPCAP).
https://www.tcpdump.org/manpages/rpcapd.8.html
Compile and run tested:
OpenWrt 21.02.0-rc4 r16256-2d5ee43dc6 on x86/64 and mvebu/cortexa9
Signed-off-by: Stephan Schmidtmer <hurz@gmx.org>
(cherry picked from commit 891c8676a1)
OpenWrt's special gpio-button-hotplug driver is still using
exclusively the legacy GPIO Subsystem gpio_ API.
While it still does work fine for most devices, upstream
linux is starting to convert platform support like that of
the APU2/3/4 to the new GPIOD LOOKUP tables that are not
supported by it.
Hence, this patch replaces the gpio_ calls present in
gpio-button-hotplug with gpiod_ equivalent wherever
it's possible. This allows the driver to use the
gpiod lookup tables and still have a fallback for
legacy platform data code that just sets button->gpio
set to the real button/switch GPIO.
As a bonus: the active_low logic is now being handled
by the linux's gpio subsystem too. Another issue that
was address is the of_handle leak in the dt parser
error path.
Tested with legacy platform data: x86_64: APU2, MX-100
Tested on OF: ATH79; MR18, APM821xx: Netgear WNDR4700,
RAMIPS: WL-330N3G
LANTIQ: AVM FritzBox 7360v1
Reported-by: Chris Blake <chrisrblake93@gmail.com>
Tested-by: Chris Blake <chrisrblake93@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 2b0378cf9f)
Allow RAM size to be passed thru U-Boot. There are 128MB and 64MB
versions of Minew G1-C. This is also in line with the behaviour of
most other RAMIPS boards.
Signed-off-by: Bruno Randolf <br1@einfach.org>
When doing parallel build on a fast machine with bottleneck in i/o,
m_xt.so may start linking faster than dynsyms.list gets populated,
resulting in error:
ld:dynsyms.list:0: syntax error in dynamic list
Fix this by adding dynsyms.list as make dependency to m_xt.so
Described also here:
https://bugs.openwrt.org/index.php?do=details&task_id=3353
Change from v1:
- add dynsysms.list dependancy only when shared libs are enabled
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Fixes: FS#3353
(cherry-picked from commit edd53df168)
This resolves incosnsitencies of the configured RX / TX flow control
modes between different boards or bootloaders.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4d81f08771)
fixing linking error when --enable-devcrypto=yes
fixes: 7d92bb0509 wolfssl: update to 4.8.1-stable
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
(cherry picked from commit be3e260f92)
It's the default anyway and this just looks confusing, as if it wasn't.
Switch to AUTORELEASE while at it.
The binary size is unchanged.
Signed-off-by: Andre Heider <a.heider@gmail.com>
(cherry picked from commit 7cb5af30f4)
This gates out anything that might introduce semantically frivolous jitter,
maximizing chance of identical object files.
The binary size shrinks by 8kb:
1244352 staging_dir/target-mipsel_24kc_musl/usr/lib/libwolfssl.so.4.8.1.39c36f2f
1236160 staging_dir/target-mipsel_24kc_musl/usr/lib/libwolfssl.so.4.8.1.39c36f2f
Signed-off-by: Andre Heider <a.heider@gmail.com>
(cherry picked from commit c76300707e)
This patch removes CONFIG_MTD_SPI_NOR_USE_4K_SECTORS from the default
symbols for the ath79/mikrotik target.
MikroTik devices hold some of their user-configurable settings in the
soft_config partition, which is typically sized 4 KiB, of the SPI NOR
flash memory. Previously, in the ar71xx target, it was possible to use
64 KiB erase sectors but also smaller 4 KiB ones when needed. This is
no longer the case in ath79 with newer kernels so, to be able to write
to these 4 KiB small partitions without erasing 60 KiB around, the
CONFIG_MTD_SPI_NOR_USE_4K_SECTORS symbol was added to the defaults.
However, this ended up making sysupgrade images which were built with
64 KiB size blocks not to keep settings (e.g., the files under
/etc/config/) over the flashing process.
Using 4 KiB erase sector size on the sysupgrade images (by setting
BLOCKSIZE = 4k) allows keeping settings over a flashing process, but
renders the process terribly slow, possibly causing a user to
mistakenly force a manual device reboot while the process is still on-
going. Instead, ditching the 4 KiB erase sectors for the default
64 KiB erase size provides normal SPI write speed and sysupgrade times,
at the expense of not being able to modify the soft_config partition
(which is rarely a required thing).
An OpenWrt patch for MTD_SPI_NOR_USE_4K_SECTORS_LIMIT may once have
allowed to use different per-partition erase sector sizes. Due to
changes on recent kernels it now only works on a per-device basis.
Also, partial eraseblock write can be performed in ath79 with kernels
5.4 and lower, by copying the blocks from the 64 KiB, erasing the whole
sector and restoring those blocks not meant to be modified. A kernel
bump had that patch broken for a long time, but got fixed in bf2870c.
Note: the settings in the soft_config partition can be reset to their
defaults by holding the reset button for 5 seconds (and less than 10
seconds) at device boot.
Fixes: FS#3492 (sysupgrade […] loses settings...)
Fixes: a66eee6336 (ath79: add mikrotik subtarget)
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
(cherry picked from commit 68d91f08ed)
Changes from 4.7.0:
Fix one high (OCSP verification issue) and two low vulnerabilities
Improve compatibility layer
Other improvements and fixes
For detailed changes refer to https://github.com/wolfSSL/wolfssl/releases
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
(cherry picked from commit 7d92bb0509)
[Added patch to allow compilation with libtool 2.4]
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Backport upstream patch to fix build with GCC 10 on 32 x86 targets.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 718a4f4780)
This fixes a kernel build problem.
The removed parts of the patch are already applied upstream.
Fixes: b4ed8a9275 ("kernel: bump 5.4 to 5.4.154")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9501ce909f)
They're preferred terminal descriptions for tmux, with additional support to
some special characters and italic fonts. More info can be found at:
https://github.com/tmux/tmux/wiki/FAQ
Fixes: FS#3404
Signed-off-by: Jitao Lu <dianlujitao@gmail.com>
(cherry picked from commit 917126ff4c)
The terminfo is required by the popular terminal multiplexer screen and
tmux, offer it by default as the size impact is minimal with 885 Bytes.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 6a6b5a677e)
The terminfo files were all in one row which is terrible to read.
Split them over multiple lines to improve readability.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 75ea474b90)
