Fixes issues with RTL8156 2.5G USB adapters
- # ethtool eth1
Settings for eth1:
Supported ports: [ ]
Supported link modes: Not reported
Supported pause frame use: No
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 2500Mb/s
Duplex: Half
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
MDI-X: Unknown
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
- #
- r8152: break the loop when the budget is exhausted
- r8152: Block future register access if register access fails
- r8152: Rename RTL8152_UNPLUG to RTL8152_INACCESSIBLE
- r8152: add vendor/device ID pair for D-Link DUB-E250
- r8152: try to use a normal budget
- r8152: set bp in bulk
- r8152: adjust generic_ocp_write function
- r8152: fix the autosuspend doesn't work
- r8152: Add __GFP_NOWARN to big allocations
- r8152: reduce the control transfer of rtl8152_get_version()
- r8152: remove rtl_vendor_mode function
- r8152: avoid to change cfg for all devices
- r8152: add USB device driver for config selection
- r8152: use napi_gro_frags
- cdc_ether: no need to blacklist any r8152 devices
- cdc_ether: add u-blox 0x1313 composition
Build system: x86_64
Build-tested: bcm2711, rockchip, x86/64
Run-tested: bcm2711/RPi4B, rockchip/nanopi r2s, x86/64
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Backport merged upstream patch that adds support for firmware loader
from NVMEM or attached filesystem for Aquantia PHYs.
Refresh all kernel patches affected by this change.
Also update the path for aquantia .ko that got moved to dedicated
directory upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Another Qualcomm-based USB-connected modem, offering endpoints
0 : rndis_host (link to voip subsystem listening on 169.254.5.100)
1 : rndis_host (?)
2 : option (?)
3 : option (at)
4 : option (at)
5 : option (?)
6 : GobiNet (qmi)
7 : ?
Add support for this modem in rndis_host, option and qmi_wwan driver
which allows the modem to be used with ModemManager.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
New revision of Methode eDPU boards uses Marvell 88E6361 switch, so lets
backport it from kernel 6.5.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This reverts commit 5356462ce5.
Kernel switching to fw_devlink=on as default broke probing some devices.
Revert it until we get a proper fix.
It seemed that mtd OF_POPULATED hack resolved probing issues but
apparently not all of them. We got reports about reading MAC using NVMEM
not working and USB controllers not working.
Ref: #10232Fixes: #13412
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Netgear Nighthawk RAX120v2 AX WIFI router with 5 1G and 1 5G ports.
The majority of the code is based on @jewwest's PR #11830.
Specifications:
* CPU: Qualcomm IPQ8074 Quad core Cortex-A53 2.2GHz
* RAM: 1024MB of DDR3 (Nanya NT5CC256M16EP-EK × 2)
* Flash: SPI-NAND 512 MiB (Winbond W29N04GZBIBA)
* Ethernet: 4x 10/100/1000 Mbps LAN,
1x 10/100/1000 Mbps WAN (Qualcomm QCA8075),
1x 10/100/1000/2500/5000 Mbps LAN/WAN (Aquantia AQR111B0 PHY)
* Wi-Fi:
* 2.4 GHz: Qualcomm QCN5024 4x4
* 2x 5 GHz: Qualcomm QCN5054 4x4
* USB: 2x USB 3.0
* LEDs: Power, 2.4GHz & 5GHz Radio, WPS, WAN, USB1 & USB2, 5G LAN
* Keys: LEDs On/Off, Power, Reset, RFKILL, WPS
* UART: Marked J9003 VCC TX RX GND, beginning from "1". 3.3v, 115200n8
* Power: 19 VDC, 3.1 A
Installation:
* Flashing OpenWrt is done in two steps:
a) Flash *-squashfs-web-ui-factory.img from stock UI (thanks to @wangyu-).
This writes an initramfs based OpenWrt image onto the RAX120v2
b) From OpenWrt flash the *-squashfs-sysupgrade.bin using LuCI or the commandline
* U-Boot allows booting an initramfs image via TFTP:
- Set ip of your PC to 192.168.1.100
- At the serial console interrupt boot at "Hit any key to stop autoboot:"
- In u-boot run `tftpsrv`
- On your PC send the OpenWrt initramfs image:
tftp 192.168.1.1 -m binary -c put openwrt-ipq807x-generic-netgear_rax120v2-initramfs-uImage.itb
Make 5G Aquantia phy work:
For the 5G port labeled 'lan5' to work a firmware is needed. This can be loaded in
u-boot by writing the firmware to the correct mtd partition.
The firmware file found in the Netgear stock firmware under /lib/firmware/ named
'AQR-G3_v4.3.C-AQR_DNI_DR-EQ35AX8-R-prov1_ID23888_VER1311.cld' is needed and has to
be converted to a MBN file.
The `mkheader.py` script used here can be found in the Netgear V1.2.8.40 GPL source,
under 'git_home/u-boot.git/tools/mkheader.py'
Convert the CLD file to MBN using:
$ python2 mkheader.py 0x44000000 0x13 <*.cld file> aqr_4.3.C.mbn
This MBN file can then be flashed to the MTD partition to be used by u-boot.
The necessary files can also be found in
https://github.com/boretom/openwrt-fork/tree/rax120v2/aquantia-firmware
* Write MBN file to MTD partition to be loaded automatically by u-boot:
U-boot automatically tries to load the firmware from nand at address 0x7e00000 which
corresponds to `/dev/mtd25` in OpenWrt.
- find ETHPHYFW partition while running OpenWrt (expected: /dev/mtd25)
$ fgrep -i 'ethphyfw' /proc/mtd
mtd25: 00080000 00020000 "ethphyfw
- copy mbn file to /tmp/ folder of the router
$ scp aqr-v4.3.C.mbn 192.168.1.1:/tmp/
- write mbn file to ethphyfw partition
$ mtd write /tmp/aqr_v4.3.C.mbn /dev/mtd25
Revert to stock firmware:
* Flash the stock firmware to the bootloader using TFTP/NMRP.
References to RAX120v2 GPL source:
https://www.downloads.netgear.com/files/GPL/RAX120-V1.2.8.40_gpl_src.zip
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thomas Kupper <thomas.kupper@gmail.com>
Backport patch adding support for LED PHY directly in PHY ops struct.
Add new PHYLIB_LEDS config and refresh patches.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 79af0593a3.
A hack adjusting fw_devlink value was added to workaround issue with
probing device drivers caused by of_platform_populate(). With upstream
mtd commit (the one adding OF_POPULATED) backported there is no need for
that hack anymore.
Ref: 3eebb91317 ("kernel: backport proper fix for mtd preventing devices probing")
Ref: #10232
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This change makes it possible to use the GPIO_OPEN_DRAIN /
GPIO_OPEN_SOURCE Flags when exporting GPIOs via dts.
We need to emulate the open-source or open-drain functionalities for the
initial value, because the used functions (gpiod_direction_output_raw)
do not take this into account.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
When refreshing the hack patches for Linux 6.1 the part of the uImage.FIT
partition parser patch which takes care of allowing mtdblock and ubiblock
devices to have partitions has been dropped, supposedly by accident.
Re-add a that part to the patch, so devices using a uImage.FIT filesystem
sub-image as rootfs can work with Linux 6.1.
Fixes: 19a246bb65 ("generic: 6.1: manually refresh hack patches")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Manually rebased:
generic/hack-6.1/220-arm-gc_sections.patch
armsr/patches-6.1/221-armsr-disable_gc_sections_armv7.patch
All other patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
All patches automatically rebased.
Acknowledgment to @john-tho for the changes to fs.mk to accommodate new paths
introduced in 29429a1f58
Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B
Signed-off-by: John Audia <therealgraysky@proton.me>
This patch initially introduced in 94b4da9b4a
breaks mvebu devices when using vlan filtering with kernel 5.15 or 6.1,
it was working ok in 5.10.
With this patch, frame that should exit untagged from the switch exit tagged.
Running 'tcpdump -Q out -evnnli eth1' (eth1 being the dsa interface)
- with the hack, frame is sent directly to the
destination port 4 with VID 2, so the switch leave the tag as instructed:
11:22:33:44:55:66 > 77:88:99:aa:bb:cc, Marvell EDSA ethertype 0xdada (Unknown), rsvd 0 0, mode From CPU, target dev 0, port 4, tagged, VID 2, FPri 0, ethertype ARP (0x0806), length 50: Ethernet (len 6), IPv4 (len 4), Request who-has 5.6.7.8 tell 1.2.3.4, length 28
- without the hack, frame is sent to the switch that
performs the forwarding decision and untagging:
11:22:33:44:55:66 > 77:88:99:aa:bb:cc, Marvell EDSA ethertype 0xdada (Unknown), rsvd 0 0, mode Forward, dev 1, port 0, tagged, VID 2, FPri 0, ethertype ARP (0x0806), length 50: Ethernet (len 6), IPv4 (len 4), Request who-has 5.6.7.8 tell 1.2.3.4, length 28
Removing this patch makes my Turris Omnia usable with vlan filtering,
ie wifi device can talk to wired device again.
Using kernel 5.15 some broadcast/multicast traffic is still leaked
(on a VLAN 2 access port I see tagged VLAN 3 frame),
using kernel 6.1 fixes that.
People needing the extra performance should try the bridger package.
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Backport initial LEDs hw control support. Currently this is limited to
only rx/tx and link events for the netdev trigger but the API got
accepted and the additional modes are working on and will be backported
later.
Refresh every patch and add the additional config flag for QCA8K new
LEDs support.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>