97bacb70138a libfstools: query drivers by priority
41e619ed1352 block: recognize /dev/fit* block devices
bc3b8cdd3de3 libfstools: add uImage.FIT fitblk driver
846302d09246 libfstools: partname: raise priority to 25
1a5695925ecf mount_root: add support for passing args to mount_root start
1858a492c300 mount_root: permit to pass mount options for rootfs mount
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Linksys MX4200 is a 802.11ax Tri-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8174 Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 512Mb NAND
* Ethernet: 4x1G RJ45 ports (QCA8075)
* WLAN:
* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5054 2x2@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LED-s:
* RGB system led
* Buttons: 1x Soft reset 1x WPS
* Power: 12V DC Jack
Installation instructions:
Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup.
Login with your admin password. The default password can be found on a sticker under the device.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device.
Then you would need to write openwrt to the other partition for it to work
- First Check booted partition
fw_printenv -n boot_part
- Then install Openwrt to the other partition if booted in slot 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin alt_kernel
- If in slot 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4200v(X)-squashfs-factory.bin kernel
Replace (X) with your model version either 1 or 2
Signed-off-by: Mohammad Sayful Islam <sayf.mohammad01@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
d852f877920b service: Fix retriggering of init.d-scripts.
7e6c6efd6fbc udebug: add support for logging via udebug
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2b39a27d8bcc libubus: fix reconnect with auto subscribe
f84eb5998c6e libubus: fix initial subscribe with autosubscribe
Signed-off-by: Felix Fietkau <nbd@nbd.name>
3a07943 block: support skipping uuid check
56a9b4e block: consider currently mounted root device first
9cd09d4 block: try to find the root device on both / and /rom
c1a8d95 block: support extroot on already mounted overlay
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Some packages won't ever have something to patch as they normally
install files or are meta-packages.
For these special packages, disable QUILT refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is needed for ksh/bash style process substitution such as
<(command) and >(command) which was introduced in ash as of busybox
version 1.34.0 to work.
Signed-off-by: Erik Karlsson <erik.karlsson@genexis.eu>
Due to some hiccup my local urngd-2023-07-25-7aefb47b.tar.xz ended up
being different from archived one. Repackaging it locally confirmed the
previous hash was incorrect.
Fixes: c74b5e09e6 ("urngd: update to the latest master")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The existing implementation incorrectly reported `running` for services
without any instances or with all instances stopped/terminated.
Improve the default implementation of `/etc/init.d/* status` to properly
report services with not running instances. In case a service exists,
but without running instance, the status call will now report
"not running" with exit code 5. In case some instances are running and
some are stopped/terminated, the call will report "running (X/Y)" where
`X` denoted the amount of running instances and `Y` the amount of total
registered ones.
Ref: https://forum.openwrt.org/t/x/159443
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
7aefb47 jitterentropy-rngd: update to the v1.2.0
What's interesting about jitterentropy-rngd v1.2.0 release is that it
bumps its copy of jitterentropy-library from v2.2.0 to the v3.0.0. That
bump includes a relevant commit 3130cd9 ("replace LSFR with SHA-3 256").
When initializing entropy jent calculates time delta. Time values are
obtained using clock_gettime() + CLOCK_REALTIME. There is no guarantee
from CLOCK_REALTIME of unique values and slow devices often return
duplicated ones.
A switch from jent_lfsr_time() to jent_hash_time() resulted in many less
cases of zero delta and avoids ECOARSETIME.
Long story short: on some system this fixes:
[ 6.722725] urngd: jent-rng init failed, err: 2
This is important change for BCM53573 which doesn't include hwrng and
seems to have arch_timer running at 36,8 Hz.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Based on Paul Fertser <fercerpav@gmail.com>'s guidance:
Change AUTORELEASE in rules.mk to:
```
AUTORELEASE = $(if $(DUMP),0,$(shell sed -i "s/\$$(AUTORELEASE)/$(call commitcount,1)/" $(CURDIR)/Makefile))
```
then update all affected packages by:
```
for i in $(git grep -l PKG_RELEASE:=.*AUTORELEASE | sed 's^.*/\([^/]*\)/Makefile^\1^';);
do
make package/$i/clean
done
```
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Specifications:
SOC: Atheros/Qualcomm QCA9557-AT4A @ 720MHz
RAM: 2x Winbond W9751G6KB-25 (128 MiB)
FLASH: Hynix H27U1G8F2BTR-BC TSOP48 ONFI NAND (128 MiB)
WIFI1: Atheros AR9550 5.0GHz (SoC)
WIFI2: Atheros AR9582-AR1A 2.4GHz
WIFI2: Atheros AR9582-AR1A 2.4GHz + 5GHz
PHYETH: Atheros AR8035-A, 802.3af PoE capable Atheros (1x Gigabit LAN)
LED: 1x Power-LED, 1 x RGB Tricolor-LED
INPUT: One Reset Button
UART: JP1 on PCB (Labeled UART), 3.3v-Level, 115200n8
(VCC, RX, TX, GND - VCC is closest to the boot set jumper
under the console pins.)
Flashing instructions:
Depending on the installed firmware, there are vastly different
methods to flash a MR18. These have been documented on:
<https://openwrt.org/toh/meraki/mr18>
Tip:
Use an initramfs from a previous release and then use sysupgrade
to get to the later releases. This is because the initramfs can
no longer be built by the build-bots due to its size (>8 MiB).
Note on that:
Upgrades from AR71XX releases are possible, but they will
require the force sysupgrade option ( -F ).
Please backup your MR18's configuration before starting the
update. The reason here is that a lot of development happend
since AR71XX got removed, so I do advise to use the ( -n )
option for sysupgrade as well. This will cause the device
to drop the old AR71xx configuration and make a new
configurations from scratch.
Note on LEDs:
The LEDs has changed since AR71XX. The white LED is now used during
the boot and when upgrading instead of the green tricolor LED. The
technical reason is that currently the RGB-LED is brought up later
by a userspace daemon.
(added warning note about odm-caldata partition. remove initramfs -
it's too big to be built by the bots. MerakiNAND -> meraki-header.
sort nu801's targets)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This reduces open coding and allows to easily add a knob to enable
it treewide, where chosen packages can still opt-out via "no-lto".
Some packages used LTO, but not the linker plugin. This unifies 'em
all to attempt to produce better code.
Quoting man gcc(1):
"This improves the quality of optimization by exposing more code to the
link-time optimizer."
Also use -flto=auto instead of -flto=jobserver, as it's not guaranteed
that every buildsystem uses +$(MAKE) correctly.
Signed-off-by: Andre Heider <a.heider@gmail.com>
This reduces open coding and allows to easily add a knob to
enable it treewide, where chosen packages can still opt-out via
"no-gc-sections".
Note: libnl, mbedtls and opkg only used the CFLAGS part without the
LDFLAGS counterpart. That doesn't help at all if the goal is to produce
smaller binaries. I consider that an accident, and this fixes it.
Note: there are also packages using only the LDFLAGS part. I didn't
touch those, as gc might have been disabled via CFLAGS intentionally.
Signed-off-by: Andre Heider <a.heider@gmail.com>
d978830 rc: add option to get info for a single script in list method
632b4fc rc: add option to skip running check for list method
5577db9 rc: add support for scanning USE_PROCD and skip running if not supported
4de3f02 rc: fix and improve script scanning START and STOP
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
I've somehow managed to commit wrong package mirror hash in commit 36076b5a40
("ubus: update to version 2022-06-15"), so lets fix it by using a proper
one.
Fixes: 36076b5a40 ("ubus: update to version 2022-06-15")
Reported-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Update which contains just a following fix:
* ubusd: add lookup command queuing support
Defers and continues a client's lookup command to avoid unnecessary
buffering under load.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
1ea5855 partname: Introduce fstools_partname_fallback_scan option
While at it also drop AUTORELEASE from PKG_RELEASE.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
c0df2a7 iwinfo: add "band" and "mhz" to the scan output
06ad60f iwinfo: add "band" to the freqlist output
b32fd32 iwinfo: add flags to freqlist output
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
04d7570 jail: fs: don't overwrite existing mount target
6b9629b jail: don't assume positive return value of creat
190f13a init: attempt to mount efivarfs
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The libraries libpthread, libdl, libutil, libanl have been integrated
into the libc library in version 2.34. it is not needed to explicitly
link them any more.
Most of the functions have been moved from the librt.so into libc.so
some time ago already.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
