The registers L2_PORT_STATIC_MV_ACT seem to specify the action to take
when the source address of a packet exists as a static fdb entry on
another port. By default the configured action is to drop such packets.
For standalone ports, this behaviour is undesired, as all traffic should
be forwarded to the CPU. So change the action to forward on standalone
ports.
A situation where this issue can occur is when a non-offloaded bond
interface is part of a bridge. In that case, the CPU port will have fdb
entries for devices connected to the bond interface, which are managed
by the assisted learning feature.
For now, this is only implemented for RTL838x/RTL839x, as the available
set of registers differs for the other devices.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
All ports are disabled by default, so configure the port isolation masks
and the pm field accordingly in the setup function. When port_enable is
called for a port, the isolation masks will be set up so that traffic
can flow between the port and the CPU.
While at it, change the code to also use the traffic_set method in
rtl83xx_setup, instead of writing to the RTL838x_PORT_ISO_CTRL(i)
registers directly.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Correctly update the isolation mask of the port being configured. The
port_bitmap variable should contain all other bridge members and needs
to be actually removed from the isolation mask instead of added to it.
Also actually remove the port being configured from the pm field of the
other ports, so that any other ports that are currently disabled will be
configured correctly when they are enabled.
Fixes: df8e6be59a ("rtl838x: add new architecture")
[fixed updating pm field of other ports]
Fixes: 2b88563ee5 ("realtek: update the tree to the latest refactored version")
[reintroduced incorrect pm field update]
Fixes: 27029277f9 ("realtek: add switch driver support for the RTL93XX based switches")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Add support for NXP LS1028ARDB reference board. It's a dual core
Coretex-A53 board with 4G RAM and 5 Eternet ports (4 ports are
connected to MSCC Felix switch).
The original layout of NXP board has been kept but firmware
images are adapted to be more sysupgrade friendly. At the moment
NOR and SD boots are supported.
NOR flash instructions:
* make sd card with sdboot image
* boot
* write firmware image to spi flash
$ mtd write /tmp/openwrt-layerscape-armv8_64b-fsl_ls1028a-rdb-
squashfs-firmware.bin /dev/mtd0
* change jumper to NOR boot and reset
V3:
* Added board specific network defaults for lan/wan
v2:
* Added INA220 curent monitor, PCF2129 RTC clock and NXP
SA56004ED temperature sensor to default packages
* removed compat fixups for thist board
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
Support uboot for NXP LS1028ARDB reference board. GIC V3 has to
be disabled in the uboot config to allow booting upstream kernels.
This patch can be dropped once uboot is updated to 2022.04 version
to nxp-qoriq github lf-6.1.1 branch.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
There seems to be a difference in firmware calling convention
between upstream and NXP kernels. On some cpus like ls1028
it will hang on firmware secure get random when using LF uboot
with upstream kernel. Instead of commenting it out, don't call
get radnom seed when "kaslr-seed" is not present in device tree.
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@protonmail.ch>
To support the widest variety of modems, allow restoring previous
behaviour of configuring the link throug means of DHCP(v6) exclusively.
Change the default value of "dhcp" and "dhcpv6" UCI options to "auto",
while keeping the default behaviour of "prefer out-of-band configuration",
intact. Setting "dhcp" or "dhcpv6" to boolean 1 will now force using
DHCP and DHCPv6, respectively.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
The ZTE MF282 is a LTE router used (exclusively?) by the network operator
"3".
Specifications
==============
SoC: QCA9563 (775MHz)
RAM: 128MiB
Flash: 8MiB SPI-NOR + 128MiB SPI-NAND
LAN: 1x GBit LAN
LTE: ZTE MF270 (Cat4), detected as P685M
WiFi: QCA9880ac + QCA9560bgn
MAC addresses
=============
LAN: from config
WiFi 1: from config
WiFi 2: +1
Installation
============
TFTP installation using UART is preferred. Disassemble the device and
connect serial. Put the initramfs image as openwrt.bin to your TFTP server
and configure a static IP of 192.168.1.100. Load the initramfs image by
typing:
setenv serverip 192.168.1.100
setenv ipaddr 192.168.1.1
tftpboot 0x82000000 openwrt.bin
bootm 0x82000000
From this intiramfs boot you can take a backup of the currently installed
partitions as no vendor firmware is available for download.
Once booted, transfer the sysupgrade image and run sysupgrade.
LTE Modem
=========
The LTE modem is probably the same as in the MF283+, all instructions
apply.
Configuring the connection using modemmanager works properly, the modem
provides three serial ports and a QMI CDC ethernet interface.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Synchronize the ath11k backports with the current ath-next tree.
This replaces the 160MHz with the upstreamed one, fixes 6GHz only WIPHY
registration, allows SAR usage on WCN6750 and plenty of REO fixes.
Signed-off-by: Robert Marko <robimarko@gmail.com>
While improving access path analysis a typo happened. Now it can happen
that gcc misscompiles. The patch is fixing the issue. However, also
other gcc versions 10.2+ are affected. They also should be bumped or the
fix should be backported.
For more bug information have a look at:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=109585
Signed-off-by: Nick Hainke <vincent@systemli.org>
Rename to Fritz!Box to keep naming uniform.
Fixes: ceac4ae3b4 ("lantiq: xway: add support for AVM FRITZ!Box 7330")
Signed-off-by: Nick Hainke <vincent@systemli.org>
Changes:
43f81b4 wireless-regdb: update regulatory database based on preceding changes
66f245d wireless-regdb: Update regulatory rules for Hong Kong (HK)
e78c450 wireless-regdb: update regulatory rules for India (IN)
1647bb6 wireless-regdb: Update regulatory rules for Russia (RU). Remove DFS requirement.
c076f21 Update regulatory info for Russia (RU) on 6GHz
Signed-off-by: Yuu Toriyama <PascalCoffeeLake@gmail.com>
Using the local gnulib source during autogen.sh
allows for fine-grained control over the macros
and source files for use with gettext
but part of gnulib instead of gettext,
without having to wait for a release
or deal with gnulib as a git submodule.
This is an alternative to running autoreconf.
It also removes the need to patch macros
in the case where there is a conflict
between the source and our aclocal directory.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Using the local gnulib source during bootstrap
allows for fine-grained control over the macros
and source files for use with coreutils
but part of gnulib instead of coreutils,
without having to wait for a release
or deal with gnulib as a git submodule.
In this case, the execution of autotools
must be skipped by force.
Autoconf and Automake during bootstrap on coreutils
only works right when using directly checked-out source.
There is a symbol in gnulib, @GNULIB_TIME@
that is not yet defined in coreutils source,
so we use the backup of lib/time.in.h instead
of the one provided by gnulib source.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Using the local gnulib source during bootstrap
allows for fine-grained control over the macros
and source files for use with libtool
but part of gnulib instead of libtool,
without having to wait for a release
or deal with gnulib as a git submodule.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Some users have reported that gettext builds
are attempting to link to libxml2
while it was supposed to be configured
to use it's own built-in substitute.
Configure gettext to require and link
to our local libxml2 explicitly.
Add a patch to revert upstream commit 87927a4e2
which forces libtextstyle to use the built-in libxml,
no matter what the configuration is,
making that option configurable again
after the configure script is regenerated.
Reported-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Instead of editing the SUBDIRS variable with a patch,
it can be overriden at the end of the command line when invoking Make.
This tool has a series of recursive Makefiles in each subdirectory,
therefore SUBDIRS is set to a pattern of Make functions
so that the result is variable depending on the current subdirectory
that Make is being invoked in.
Some of the subdirectories don't have a Makefile and are just storing files
for another subdirectory Makefile target,
therefore we have to place a fake Makefile that does nothing.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Instead of editing the SUBDIRS variable with a patch,
it can be overriden at the end of the command line when invoking Make.
This tool has a series of recursive Makefiles in each subdirectory,
therefore SUBDIRS is set to a pattern of Make functions
so that the result is variable depending on the current subdirectory
that Make is being invoked in.
By eliminating the patch, autoreconf is no longer required.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Instead of editing the SUBDIRS variable with a patch,
it can be overriden at the end of the command line when invoking Make.
Skip the build for po files as well, which is causing a conflict
depending on the version of gettext detected, and macros present.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
GNU standards requires certain files at the top-level directory
of a package that automake is used with, mostly documentation.
If one of these files happens to be missing, autoreconf would fail.
Move these file requirements to the more strict 'GNITS' setting.
Link: https://www.gnu.org/software/automake/manual/html_node/Strictness.html
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Some new releases of GNU tools are checking for a higher version
of makeinfo than what our scripted alternative shows
when working with checked-out sources instead of releases.
Since this is a "fake" makeinfo we can also just fake the version.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
These 7 macro files are provided by gnulib,
so we can now replace these statically stored copies
with the latest copy from GNU sources.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
By having a local copy of gnulib, we can:
import the latest macro fixes into any package,
get rid of some statically stored macros that were otherwise missing,
bootstrap GNU tools with the latest relevant source
without having to wait for a release or rely on git submodules,
and possibly more...
The patch assists in bootstrapping by ignoring
the building of po files using gettext,
and also to allow a user-defined path to a program
to include parameters.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Some uses cases, like with autotools, need a path for 'true'
if we use them to force something to skip.
This will work by default on Linux hosts,
and require MacOS hosts to get coreutils,
which is currently installed in the CI
for 'macos-latest' host.
In the future, prereq stage can be reworked
to search for the actual binary
instead of relying on env.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
The current problems blocking the switch to the kernel 5.15 are
related to the GSWIP driver. This driver is only used by the
xrx200 subtarget. The other subtargets are unaffected by this
problem.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Kernel setting CONFIG_IO_URING supports high-performance I/O for file
access and servers, generally for more performant platforms, and adds
~45 KB to kernel sizes. The need for this on less "beefy" devices is
questionable, as is the size cost considering many platforms have kernel
size limits which require tricky repartitioning if outgrown. The size
cost is also large relative to the ~180 KB bump expected between major
OpenWRT kernel releases.
No OpenWrt packages have hard dependencies on this; samba4 and mariadb
can take advantage if available (+KERNEL_IO_URING:liburing) but
otherwise build and work fine.
Since CONFIG_IO_URING is already managed via the KERNEL_IO_URING setting
in Config-kernel.in (default Y), remove it from those target configs
which unconditionally enable it, and update the defaults to enable it
conditionally only on more powerful 64-bit x86 and arm devices. It may
still be manually enabled as needed for high-performance custom builds.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Since CONFIG_DYNAMIC_DEBUG is already managed via the KERNEL_DYNAMIC_DEBUG
setting in Config-kernel.in (default N), remove or disable it in target
configs which unconditionally enable it, along with the related setting
CONFIG_DYNAMIC_DEBUG_CORE. This saves several KB in the kernels for
ipq40xx, ipq806x, filogic, mt7622, qoriq, and sunxi.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This activates CONFIG_SLAB_FREELIST_RANDOM.
This option make the free list less predictable. This makes it harder to
exploit heap based security vulnerabilities.
This adds a little bit more code to the kernel and a small additional
compute overhead.
This option is activated in Debian by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
