Add UART pinctrl group for using only pins 80 and 81 for uart1.
This is needed on the BPi-R4 as RTS/CTS signals are used for other
on-board functions.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Replace previous patch adding paths and SerDes modes with patch series
pending upstream adding dedicated drivers for XFI T-PHY and USXGMII PCS,
extends LynxI PCS to be a standalone platform driver and as a consequence
makes much less changes to the actual Ethernet driver mtk_eth_soc.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport almost 50 commits from upstream Linux to improve thermal
drivers for MediaTek SoCs and add new LVTS driver for MT7988.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Let's pick a bunch of useful phylink changes which allow us to keep
drivers in sync with mainline Linux.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add 'fitblk' driver to replace the rejected/deprecated uImage.FIT
partition parser.
To use the new driver, add phandle /chosen/rootdisk and point it to
the MTD partition, UBI volume or block device holding the uImage.FIT.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Similar to supporting nvmem-layouts on MTD devices, also allow referencing
UBI and MMC devices in DT.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In order to allow gradually migrating the boards currently using the
uImage.FIT partition (deprecated/rejected) parser to the new fitblk
driver, skip the partition parser code in case the new fitblk driver
(which serves the same purpose) is used.
As an indicator for the use of the new fitblk driver, check if the
/chosen/rootdisk property is present in the Device Tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The partition parser approach has been rejected upstream, it will be
replaced by a small block driver which is the solution suggestion by
upstream maintainers.
As the partition parser has only been used by the mediatek target, as
a first step, move it there.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport two commits from Linux 6.3 wiring up device node parents of
ubi devices (pointing to their MTD parent) as well as ubiblock devices
(poiting to their parent UBI volume).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Convert qca807x PHY to new implementation like for other devices.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Now that Malibu (QCA807x) PHY is using the upstream driver, we dont need
support to define address of the first PHY in package, so remove the
malibu_first_phy_addr DTS property.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that QCA807x interface mode check was upstreamed, use the upstreamed
version and mark it as such.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use order described as preferred in DTS Coding Style. Mostly just move
"compatible", "reg", "ranges" and "status" properties.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
PoE devices in the realtek target have the possibility to add PSE info
to the board description via 02_network. Make this available for all
targets, by moving the uci_set_poe() function to the globally available
uci-default.sh script.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
uci_set_poe() now performs two duties: filtering the list of device
ports to exclude non-PoE ports, and generating the PoE related device
config.
Extract the port filtering to an external function, which is made a bit
more readable by the use of 'sort -V [-r] | uniq -u' to filter duplicate
entries out of a (reverse) version sorted list.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The ZyXEL XGS1250-12 has a chassis fan. The fan is positioned perfectly to
provide additional cooling to the Aquantia NBase-T phys. Testing has shown
that the phys can reach temperatures upwards of 72 degrees Celsius quite
easily at about 20 degrees Celsius ambient.
Support the chassis fan to give the phys a bit of extra cooling.
Signed-off-by: Tobias Schramm <tobias@t-sys.eu>
This reverts commit 131e41614d.
Sadly it makes menuconfig fail with
tmp/.config-package.in:171: glob failed: No files found "feeds/base/utils/busybox/Config.in"
make: *** [/usr/src/openwrt/include/toplevel.mk:136: menuconfig] Error 1
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Building a package in the build system or the SDK results in different
values for the `SOURCE` property, it's either `packages/<package name>`
or `feeds/base/<package name>`. The reason is that the SDK handles
`openwrt.git` as an external feed called while the build system contains
the *base* packages directly.
Since packages created with either method are (ideally) the same (bit
for bit), align the content of SOURCE. To do so this commit creates a
symlink from `feeds/base` to `$(TOPDIR)/package` and adopts the SOURCE
when building from inside the build system.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Currently, we are checking whether the PHY package mode matches the
individual PHY interface modes at PHY package probe time, but at that time
we only know the PHY package mode and not the individual PHY interface
modes as of_get_phy_mode() that populates it will only get called once the
netdev to which PHY-s are attached to is being probed and thus this check
will always fail and return -EINVAL.
So, lets move this check to .config_init_once as at that point individual
PHY interface modes should be populated.
Fixes: 16364e4100 ("generic: 6.1: backport QCA807x PHY patches")
Signed-off-by: Robert Marko <robimarko@gmail.com>
This Qualcomm Gigabit phy driver was mistakenly added because
MT76x8 does not support external phy, and it only supports max
100M full duplex speed.
Fixes: cadf517107 ("ralink: add support for mt7628")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Xiaomi AX9000 apply a special PHY LEDs configuration where the unique
green LED for each qca807x PHY port is turned on also on 1000Mbps link.
Apply this special configuration to reflect original implementation.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Xiaomi AX3600 apply a special PHY LEDs configuration where the unique
green LED for each qca807x PHY port is turned on also on 1000Mbps link.
Apply this special configuration to reflect original implementation.
Also enable CONFIG_PHYLIB_LEDS to actually expose the PHY LEDs if
defined in DT.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Convert every qca807x PHY definition in DT to new PHY package
implementation to correctly support applying fixup for the correct PHY
mode.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Port 0-4 have the mode set to SGMII instead of PSGMII. Now that we use
the upstream qca807x driver, this conflicts with the qca SSDK driver
that expects the mode to be PSGMII as for not integrated driver, it does
refer to the real PHY mode.
Update the entry for port 0-4 to PSGMII to solve warning from qca SSDK
in ipq8074-ess.dtsi.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
IPQ807x have integrated qca8074 PHY supported by the upstream qca807x driver.
Enable it to use it instead of the downstream qca SSDK variant.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Adapt patches to new Upstream QCA807x PHY driver.
Rework the PHY patch to new PHY Package nodes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport QCA807x PHY patches merged upstream that introduce the new
concept of PHY package.
Also add in generic config the new Kconfig CONFIG_QCA807X_PHY.
All affected patch automatically refreshed with make
target/linux/refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport Aquantia PHY endianess patch. While the current implementation
works ok for Little-Endian targets, backport patch to prevent any kind
of malfunction if in the future we will have Big-Endian target with
Aquantia PHYs.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Commit d737ae99cb ("qualcommax: Fix Buffalo WXR-5950AX12 Ethernet
DTS") reverted the switch bmp to the original OEM definition and
added the malibu_first_phy_addr property.
Problem is that OEM bmp definition is wrong and actually doesn't make sense,
probably caused by copy-paste of the QCOM reference DTS without actually
setting real values. What actually fixed the regression was adding the
malibu_first_phy_addr as without it the MALIBU PHY was actually not
correctly configured and the Aquantia PHY were actually configured as
MALIBU PHY.
Fix all these wrong PHY definition.
The BPM is reverted and the following fixes are applied:
- Drop ESS_PORT1 as it's not actually attached in HW.
- Move ESS_PORT5 AGAIN from lan to wan. This refer to the first Aquantia
PHY that is labelled "wan"
- Move ESS_PORT6 AGAIN from wan to lan. This refer to the second
Aquantia PHY that is labelled "lan1".
Also PHY tag in MDIO node are renumbered to start from 0 following the
tagging standard used also in other dts and the not attached one (reg
0x18 and reg 0x1c) are correctly dropped.
Definition for port@1 in phyinfo is dropped as it doesn't exist.
dp nodes are updated to reference the new PHY tag numbering.
Fixes: d737ae99cb ("qualcommax: Fix Buffalo WXR-5950AX12 Ethernet DTS")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The NWA50AX Pro only has a eth0 interface for its only ethernet port.
Use this port for preinit.
Fixes non-working network in failsafe mode.
Signed-off-by: David Bauer <mail@david-bauer.net>
u64_stats_init() has been unable to handle NULL pointer since
6.1 kernel. This patch fixes kernel oops on mt76x8 and rt305x
sub-target.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
In the 5.15 kernel, we use the staging driver version instead of the
downstream file.
Fixes: 88d982e3bd ("ramips: 6.1: mt7621-dma: add hsdma driver to files")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Fixes errors in the form of:
make[9]: Entering directory '/home/nick/openwrt/build_dir/target-mipsel_24kc_musl/linux-ramips_mt7620/linux-6.1.77'
CC drivers/net/ethernet/ralink/mtk_eth_soc.o
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_init':
drivers/net/ethernet/ralink/mtk_eth_soc.c:1368:51: warning: passing argument 2 of 'of_get_mac_address' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
1368 | of_get_mac_address(priv->dev->of_node, dev->dev_addr);
| ~~~^~~~~~~~~~
In file included from drivers/net/ethernet/ralink/mtk_eth_soc.c:26:
./include/linux/of_net.h:16:59: note: expected 'u8 *' {aka 'unsigned char *'} but argument is of type 'const unsigned char *'
16 | extern int of_get_mac_address(struct device_node *np, u8 *mac);
| ~~~~^~~
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_probe':
drivers/net/ethernet/ralink/mtk_eth_soc.c:1641:9: error: too many arguments to function 'netif_napi_add'
1641 | netif_napi_add(netdev, &priv->rx_napi, fe_poll, napi_weight);
| ^~~~~~~~~~~~~~
In file included from ./include/linux/etherdevice.h:21,
from drivers/net/ethernet/ralink/mtk_eth_soc.c:21:
./include/linux/netdevice.h:2611:1: note: declared here
2611 | netif_napi_add(struct net_device *dev, struct napi_struct *napi,
| ^~~~~~~~~~~~~~
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[split commit and rewrite commit message]
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream commit f48dc6b96649 ("spi: Retire legacy GPIO handling") [0]
removed support using GPIOs as chip select. Fix it by replacing cs_gpio
with cs_gpiod.
[0] - f48dc6b966
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[split commit and rewrite commit message]
Signed-off-by: Nick Hainke <vincent@systemli.org>
Change fe_hw_set_macaddr and the set_mac parameter to const to fix
errors in the form of:
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_set_mac_address':
drivers/net/ethernet/ralink/mtk_eth_soc.c:174:53: error: passing argument 2 of 'priv->soc->set_mac' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
174 | priv->soc->set_mac(priv, dev->dev_addr);
| ~~~^~~~~~~~~~
drivers/net/ethernet/ralink/mtk_eth_soc.c:174:53: note: expected 'unsigned char *' but argument is of type 'const unsigned char *'
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_hw_init':
drivers/net/ethernet/ralink/mtk_eth_soc.c:1220:45: error: passing argument 2 of 'priv->soc->set_mac' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
1220 | priv->soc->set_mac(priv, dev->dev_addr);
| ~~~^~~~~~~~~~
drivers/net/ethernet/ralink/mtk_eth_soc.c:1220:45: note: expected 'unsigned char *' but argument is of type 'const unsigned char *'
drivers/net/ethernet/ralink/mtk_eth_soc.c:1222:44: error: passing argument 2 of 'fe_hw_set_macaddr' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
1222 | fe_hw_set_macaddr(priv, dev->dev_addr);
| ~~~^~~~~~~~~~
drivers/net/ethernet/ralink/mtk_eth_soc.c:155:75: note: expected 'unsigned char *' but argument is of type 'const unsigned char *'
155 | static inline void fe_hw_set_macaddr(struct fe_priv *priv, unsigned char *mac)
| ~~~~~~~~~~~~~~~^~~
cc1: all warnings being treated as errors
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream dropped support for legacy driver [0]. Rewrite the driver like
the renesas pwm driver [1].
Fixes erros in the form of:
make: *** [/__w/openwrt/openwrt/openwrt/include/toplevel.mk:232: target/compile] Error 1
====== Make errors from logs/target/linux/compile.txt ======
| ^~~~~~~~~~~~~~
drivers/pwm/pwm-mediatek-ramips.c:107:19: note: (near initialization for 'mtk_pwm_ops.free')
drivers/pwm/pwm-mediatek-ramips.c:108:10: error: 'const struct pwm_ops' has no member named 'disable'
108 | .disable = mtk_pwm_disable,
| ^~~~~~~
drivers/pwm/pwm-mediatek-ramips.c:108:20: error: initialization of 'int (*)(struct pwm_chip *, struct pwm_device *, struct pwm_capture *, long unsigned int)' from incompatible pointer type 'void (*)(struct pwm_chip *, struct pwm_device *)' [-Werror=incompatible-pointer-types]
108 | .disable = mtk_pwm_disable,
| ^~~~~~~~~~~~~~~
drivers/pwm/pwm-mediatek-ramips.c:108:20: note: (near initialization for 'mtk_pwm_ops.capture')
cc1: all warnings being treated as errors
[0] - 0829c35dc5
[1] - ec00cd5e63
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream dropped slave_id in dai_dma [0]. So drop it also in the mt7620
support patch.
Fixes errors in the form of:
sound/soc/ralink/ralink-i2s.c: In function 'ralink_i2s_init_dma_data':
sound/soc/ralink/ralink-i2s.c:452:17: error: 'struct snd_dmaengine_dai_dma_data' has no member named 'slave_id'
452 | dma_data->slave_id = i2s->txdma_req;
| ^~
sound/soc/ralink/ralink-i2s.c:462:17: error: 'struct snd_dmaengine_dai_dma_data' has no member named 'slave_id'
462 | dma_data->slave_id = i2s->rxdma_req;
| ^~
[0] - https://lore.kernel.org/r/20211122222203.4103644-3-arnd@kernel.org
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream changed in ed5c2f5fd10d ("i2c: Make remove callback return void")
the i2c driver's remove function to return no value. Adapt the driver code
to compile with 5.15 and 6.1 like it is done in other projects [0].
Fixes errors in the form of:
make[8]: Leaving directory '/home/nick/openwrt/build_dir/target-mipsel_24kc_musl/linux-ramips_mt7621/linux-6.1.29'
CC drivers/pinctrl/pinctrl-aw9523.o
drivers/pinctrl/pinctrl-aw9523.c:1117:19: error: initialization of 'void (*)(struct i2c_client *)' from incompatible pointer type 'int (*)(struct i2c_client *)' [-Werror=incompatible-pointer-types]
1117 | .remove = aw9523_remove,
| ^~~~~~~~~~~~~
drivers/pinctrl/pinctrl-aw9523.c:1117:19: note: (near initialization for 'aw9523_driver.remove')
cc1: all warnings being treated as errors
[0] - https://gitlab.com/ddcci-driver-linux/ddcci-driver-linux/-/merge_requests/10/diffs
Signed-off-by: Nick Hainke <vincent@systemli.org>
