Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
- eth0
+ Label: Ethernet 1
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as WAN interface
- eth1
+ Label: Ethernet 2
+ AR8035 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ used as LAN interface
* 1x USB
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 3T3R 2.4 GHz Wi-Fi (11n)
* 3T3R 5 GHz Wi-Fi (11ac)
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x ethernet
- eth0
+ Label: Ethernet 1
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as WAN interface
- eth1
+ Label: Ethernet 2
+ AR8031 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ used as LAN interface
* 1x USB
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The ath patch number is already large and adding other patch for ath11k
will add more confusion with the patch numbering.
Since the support of ath11k based device is imminent, prepare the mac80211
ath patch dir and split it in the dedicated ath5k, ath9k, ath10k and ath11k
(empty for now).
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
61a71e5e49c3 bridge: dynamically create vlans for hotplug members
cb6ee9608e10 bridge: fix dynamic delete of hotplug vlans
7f199050f395 wireless: pass the real network ifname to the setup script
50381d0a2998 bridge: allow adding/removing VLANs to configured member ports via hotplug
Signed-off-by: Felix Fietkau <nbd@nbd.name>
bddc1db76d0f mt76: mt7915: drop the use of repeater entries for station interfaces
3c90f35dddac mt76: mt7915: add thermal sensor device support
afab0e8202ff mt76: mt7915: add thermal cooling device support
41cf02184699 mt76: mt7615: add thermal sensor device support
2ac6b8762565 mt76: connac: update BA win size in Rx direction
ddb301127291 mt76: mt7921: fix reset under the deep sleep is enabled
e4cbefd1d69a mt76: mt7921: avoid unnecessary consecutive WiFi resets
393eea2034d7 mt76: mt7921: fix invalid register access in wake_work
a15d46407ffa mt76: mt7921: fix OMAC idx usage
e4d267d8e900 mt76: mt7921: enable runtime pm by default
50fd8ce2412a mt76: connac: add bss color support for sta mode
e29058c3c860 mt76: mt7921: return proper error value in mt7921_mac_init
c89c8c347b1e mt76: mt7921: do not schedule hw reset if the device is not running
9f7bb428e587 mt76: mt7921: reset wfsys during hw probe
22ea365913b5 mt76: mt7915: add .offset_tsf callback
ad91f8e8e494 mt76: mt7615: add .offset_tsf callback
6f871f35e3c1 mt76: mt7915: use mt7915_mcu_get_txpower_sku() to get per-rate txpower
597b68b7daa3 mt76: mt7615: remove useless if condition in mt7615_add_interface()
3945264468eb mt76: testmode: fix memory leak in mt76_testmode_alloc_skb
bdcc57a11606 mt76: testmode: remove unnecessary function calls in mt76_testmode_free_skb
a9763452601d mt76: testmode: remove undefined behaviour in mt76_testmode_alloc_skb
4aef2a2be464 mt76: mt7615: fix potential overflow on large shift
d9dd7635b055 mt76: mt7915: use mt7915_mcu_get_mib_info() to get survey data
d740e921758a mt76: mt7921: introduce mac tx done handling
259ddfc7cb73 mt76: mt7921: update statistic in active mode only
757b93f4b179 mt76: mt7921: remove leftover 80+80 HE capability
1fcff599b2e1 mt76: allow hw driver code to overwrite wiphy interface_modes
c55c22e39b7d mt7915: update firmware to 2020110522
10548aef1f45 mt76: mt7915: improve error recovery reliability
ed6b0c79820c mt76: mt7921: set MT76_RESET during mac reset
321443258bea mt76: move mt76_rates in mt76 module
d1652e8af9e1 Revert "mt76: connac: do not schedule wake_work if the runtime-pm is disabled"
4f4cab39ed9f mt76: mt7915: read all eeprom fields from fw in efuse mode
71450535f164 mt76: mt7921: enable hw offloading for wep keys
833d577e430c mt76: mt7921: remove mt7921_get_wtbl_info routine
67b7a22d2b99 mt76: mt7921: enable random mac address during sched_scan
cf1ff7bf4f1b mt76: mt7915: setup drr group for peers
ef2f7aa8745f mt76: mt7615: update radar parameters
b9f09f530223 mt76: mt7915: fix MT_EE_CAL_GROUP_SIZE
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This makes it possible to avoid using a RADIUS server for WPA enterprise authentication
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This allows WPA enterprise roaming in the same mobility domain without any
manual key configuration (aside from radius credentials)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It allows enforcing a limit on associated stations to be enforced for the
full device, e.g. in order to deal with hardware/driver limitations
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some drivers advertise it, but it's not supported at the moment
Reported-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The colon does not directly follow the "VHT Capabilities" string
Reported-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This update only adds one commit:
b102f19bcc53 tests: Opportunistic Wireless Encryption - SA Query
The main reason for the bump is to have a newer PKG_SOURCE_DATE,
so we can reset PKG_RELEASE to 1 (this has not been done for the
most recent bump), and replace it with AUTORELEASE.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
1. Move code above interface generation
It results in more logical order. Device gets its config section
above interface section.
2. Drop the loop
We have separated code handling bridges now so $device should be
guaranteed to contain a single device name.
3. Drop section name
It's not required by netifd or LuCI & it's not needed by this script
as $device contains a single device name now.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The underlying logread process uses usock() to handle remote connections
which is able to handle both hostnames and IP addresses.
Ref: https://github.com/openwrt/luci/issues/5077
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Replace "ifname" with "device" as netifd has been recently patches to
used the later one. It's more clear and accurate.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Channel 100 is a valid channel to choose for 80MHz operation. However,
it's assigned to 5500 MHz, not 5550MHz. In fact, there is no channel
assigned to this frequency.
Fix this obbvious typo to allow ACS to select channel 100 for 80 MHz
operation again.
Signed-off-by: David Bauer <mail@david-bauer.net>
The name of the module is 'uleds', not 'leds-uleds'.
Signed-off-by: Evgeny Kolesnikov <evgenyz@gmail.com>
[improve commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes `iw dev wlan0-mesh station dump`.
8fab0c9 iw: fix ftm_request missing arguments segfault
e816fbc iw: fix mgmt dump missing arguments segfault
5d9d1b8 iw: Fix timestamp output on 32-bit architectures
4b25ae3 iw: fix pointer arithmetic in __print_he_capa
c3df363 iw: add option to print human readable event time
cd64525 iw: print ctrl port tx status event
0ba98b9 iw: use correct type in policy check for mesh
9e38dee iw: scan: fixup HE caps whitespace
17e8564 iw: scan: parse HE capabilities
5735e58 iw: util: factor out HE capability parser
6d8d507 iw: scan: add extension tag parsing
b4e1ec4 man: update wikipage URL, reformat SEE ALSO section
c56036a iw: enable 80MHz support for 6GHz band 11s mesh
fa72728 iw: handle positive error codes gracefully
7ba9093 iw: scan: add flag for scanning colocated ap
5ec60ed iw: Add 'coloc' and 'flush' options to sched_scan
f8ade75 iw: update wikipage URL
b6f2dac iw: Add support for specifying the 160MHz bandwidth when setting the channel/frequency
Signed-off-by: Andre Heider <a.heider@gmail.com>
Instead of requiring the user to call it on each BSS individually,
run it on all BSSs internally.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
899c2a4 interface: support "device" attribute and deprecate "ifname"
62e3cb5 scripts/netifd-wireless.sh: add support for specifying the operating band
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
1) Use SPDX license headers to be machine readable.
2) Update copyright to 2021.
3) Use $(PROJECT_GIT) instead of manually specifying the git url.
4) Use $(AUTORELEASE) to automatically set the correct PKG_RELEASE.
Signed-off-by: Nick Hainke <vincent@systemli.org>
The SRV was added some time ago and should be mentioned in the short
help message to avoid confusion about missing features.
Signed-off-by: Paul Spooren <mail@aparcar.org>
0d5860d fix memory leak in nat46_netdev_destroy().The netdev is forgotten to free in nat46_netdev_destroy function (#26)
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
After the commit 43fc720657
("base-files: generate "device UCI type section for bridge"), the wrong
network configuration is generated for the devices that already have the
bridge device section for VLAN, such as the devices in realtek target.
As a result, the bridge device by additional "device" section is
specified to the "ports" option in the "bridge-vlan" section and netifd
shuts down the switch and the ethernet when the network service started.
Fixes: 43fc720657 ("base-files: generate "device" UCI type section for bridge")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[rmilecki: use $ports for generate_bridge_vlan argument]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This marks all packages which depend on a target with @TARGET nonshared.
If they are not marked nonshared they would be build by the SDK build
and if this happens with a different SDK, then the SDK from the target
the package depends on, the package would not be added to the index.
This should fix the image builder for some of these packages.
This should fix the image builder at least for bcm27xx/bcm2710 and
bcm4908/generic.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ATH_REG_DYNAMIC_USER_REG_HINTS is currently not being set as mac80211
tries to set it as m which is not possible as its boolean only.
Since its used alongside user regulatory, move it to USER_REGD.
This is required for ath11k to accept regulatory changes, otherwise
it wont accept any changes and will simply force US.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch fixes a recently found problem when a zImage passed to
kexec-tools contains an appended DTB. In that case kexec boot fails because
the decompressor wrongly tries to use the non-existing appended DTB instaed
of the one passed in the register r2.
- http://lists.infradead.org/pipermail/kexec/2021-April/022353.html
Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
CONFIG_CRYPTO_DEV_TALITOS depends on FSL_SOC. This driver only makes sense
on Freescale(NXP) SoCs.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
CONFIG_CRYPTO_DEV_GEODE depends on X86_32. This driver only makes sense
on X86\geode.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
CONFIG_CRYPTO_PCOMP and CONFIG_CRYPTO_PCOMP2 have been removed in upstream commit[1].
This symbol doesn't exist since kernel 4.6 and this package is empty.
1. [ crypto: compress - remove unused pcomp interface ]
(110492183c)
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
CONFIG_CRYPTO_WORKQUEUE was removed in upstream commit[1]. This symbol doesn't
exist since kernel 5.3 and this package is empty.
1. [ crypto: cryptd - move kcrypto_wq into cryptd ]
(3e56e16863)
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Support for wolfSSL has been upstreamed to the master OpenVPN branch
in f6dca235ae560597a0763f0c98fcc9130b80ccf4, so we can use wolfSSL
directly in OpenVPN. So no more needed differnt SSL engine for OpenVPN
in systems based on wolfSSL library
Compiled && tested on ramips/mt7620, ramips/mt7621
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Adds support for LEDs on input devices. Useful for example on x86 laptops-
allows re-purposing num/caps/scroll lock LEDs.
Signed-off-by: Anderson McKinley <coyoso@tuta.io>
Since upstream commit 6467de5a8840 ("Randomize z ordinates in
scalar mult when timing resistant") WolfSSL requires a RNG for
the EC key when built hardened which is the default.
Set the RNG for the EC key to fix connections for OWE clients.
Signed-off-by: David Bauer <mail@david-bauer.net>
Since commit 6467de5a8840 ("Randomize z ordinates in scalar
mult when timing resistant") wolfssl requires a RNG for an EC
key when the hardened built option is selected.
wc_ecc_set_rng is only available when built hardened, so there
is no safe way to install the RNG to the key regardless whether
or not wolfssl is compiled hardened.
Always export wc_ecc_set_rng so tools such as hostapd can install
RNG regardless of the built settings for wolfssl.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixed b36b8b6929
("busybox: remove nslookup_lede/openwrt.patch")
It is likely dropped by mistake, This add back the changes
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Florian Ekert reported:
"I have build a fresh master branch recently, Since your last change [1]
on grub2, I have now a new dependency on liblzma for the install package
grub2-editenv.
root@st-dev-07 /usr/lib # ldd /root/grub-editenv
/lib/ld-musl-x86_64.so.1 (0x7f684b088000)
liblzma.so.5 => /usr/lib/liblzma.so.5 (0x7f684b06d000)
libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x7f684b059000)
libc.so => /lib/ld-musl-x86_64.so.1 (0x7f684b088000)
This was not the case before your update.
root@st-dev-07 /usr/sbin # ldd /usr/sbin/grub-editenv
/lib/ld-musl-x86_64.so.1 (0x7fd970176000)
libgcc_s.so.1 => /lib/libgcc_s.so.1 (0x7fd970162000)
libc.so => /lib/ld-musl-x86_64.so.1 (0x7fd970176000)
My build complains that it cannot satisfy the runtime package dependency
for grub2-editenv.
install -d -m0755 /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/ipkg-x86_64/grub2-editenv/usr/sbin
install -m0755 /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/grub-editenv /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/ipkg-x86_64/grub2-editenv/usr/sbin/
find /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/build_dir/target-x86_64_musl/linux-x86_64/grub-pc/grub-2.06~rc1/ipkg-x86_64/grub2-editenv -name 'CVS' -o -name '.svn' -o -name '.#*' -o -name '*~'| xargs -r rm -rf
Package grub2-editenv is missing dependencies for the following libraries:
liblzma.so.5
make[2]: *** [Makefile:166: /home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/bin/APOS/feckert/master/master-Maggie-455-ga5edc0e8e/x86_64/targets/x86/64/packages/grub2-editenv_2.06~rc1-1_x86_64.ipk] Error 1
make[2]: Leaving directory '/home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/package/boot/grub2'
time: package/boot/grub2/pc/compile#78.64#9.79#83.88
ERROR: package/boot/grub2 failed to build (build variant: pc).
make[1]: *** [package/Makefile:116: package/boot/grub2/compile] Error 1
make[1]: Leaving directory '/home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt'
make: *** [/home/feckert/workspace/openwrt/LDM-master-x86_64/build/openwrt/include/toplevel.mk:230: package/boot/grub2/compile] Error 2
If I add the following changes to the package all works as expected.
<snip>
- DEPENDS:=@TARGET_x86
+ DEPENDS:=@TARGET_x86 +liblzma
VARIANT:=pc
endef
This is a hotfix but I dont´t think this is the final solution, because lzma is provided by the package xz.
And This is maintained in the package feed [not the core]"
Dirk stated & offered his patch to disable liblzma and thus resolve the
'out of core dependency' problem:
"LZMA is used in mkimage.c
disabling it prints
Without liblzma (no support for XZ-compressed mips images) (explicitly disabled)
(see configure.ac)
liblzma is autodetected so this issue was present but hidden somehow
[unsure: grep/image generation does not use grub with that option]
OpenWrt does not use that feature currently
[!] some scripts and examples use --compression=xz or -C xz and those will break
grub has an internal xzlib for different "lzma" functionality
(ext. LIBLZMA from XZ (GRUB_COMPRESSION_XZ) vs. GRUB_COMPRESSION_LZMA)"
Hopefully fixes e74d81ece2 and doesn't
break anything else.
Signed-off-by: Dirk Neukirchen <plntyk.lede@plntyk.name>
[include Florian's description of how problem 1st encountered]
[bump package release]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The current version of 'uboot-envtools' package generates dedicated
uci-default file only per target. This change makes it possible to
use subtarget-specific files, with name pattern: 'target_subtarget'
(example: 'ath79_nand'). The subtarget-specific files will take
precedence over target-specific one.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This reverts commit f716c30241.
Migrating everyone to the new syntax could break downgrades. We may
reintroduce it way later if needed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Missing br- prefix could result in name conflict between DSA port
interface and bridge interface. Some devices with just one LAN port use
"lan" interface name for DSA port. Trying to create bridge with the same
"lan" name was failing.
Reported-by: David Bauer <mail@david-bauer.net>
Fixes: 43fc720657 ("base-files: generate "device" UCI type section for bridge")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
/etc/syslog.conf is used by sysklogd, and /etc/crontabs is used
by crond, both features of busybox. Given this, ownership for
these files should be bound to busybox, especially if one day
there's a way to do an in-place opkg update of busybox.
There's also the busybox provided syslogd which uses this file
if CONFIG_BUSYBOX_FEATURE_SYSLOGD_CFG is set.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
The nslookup_lede/openwrt applet was introduced in de5b8e5. It was
introduced because:
Add a new LEDE nslookup applet which is compatible with musl libc
and providing more features like ability to specify query type.
In contrast to busybox' builtin nslookup applet, this variant does
not rely on libc resolver internals but uses explicit send logic
and the libresolv primitives to parse received DNS responses.
In busybox this applet is added in 0dd3be8. In particular, this commit
introduces the variable NSLOOKUP_BIG. We set the default to true and
so nothing changes.
Signed-off-by: Nick Hainke <vincent@systemli.org>
On login busybox shows a timestamp per default contianing the build
date. Since the build date isn't reproducible per default this behaviour
was disabled by default via 34df4d40 "busybox: disable timestamp in
version".
This commit modifies busybox so that the printed timestamp reproducible
using SOURCE_DATE_EPOCH and therefore shouldn't be disabled anymore.
Before:
BusyBox v1.33.1 () built-in shell (ash)
After:
BusyBox v1.33.1 (2021-05-13 09:34:34 UTC) built-in shell (ash)
Signed-off-by: Paul Spooren <mail@aparcar.org>
netifd has been recently patched to use more accurate "ports" option
instead of "ifname". This is a simple translation between two UCI
options.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This switches from the old way of defining bridges in an "interface" UCI
section type (that should be used for layer 3 only). From now a defualt
board switch will have its own "device" UCI section type. It's a new &
preferred way of defining L2 devices.
Before:
config interface 'lan'
option type 'bridge'
option ifname 'lan1 lan2 lan3 lan4'
option proto 'static'
option ipaddr '192.168.1.1'
option netmask '255.255.255.0'
After:
config device
option name 'lan'
option type 'bridge'
list ports 'lan1'
list ports 'lan2'
list ports 'lan3'
list ports 'lan4'
config interface 'lan'
option ifname 'lan'
option proto 'static'
option ipaddr '192.168.1.1'
option netmask '255.255.255.0'
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
use AUTORELEASE since BusyBox is often updaten and PKG_RELEASE is not
consistently bumped. Also use SPDX license headers to be machine
readable and bump the copyright year to 2021.
Signed-off-by: Paul Spooren <mail@aparcar.org>
02dd2f2df7cb fix unannotated fall-through warnings
3052f2f67686 extdev: remove unused function
2a97fd006c3b device: add support for configuring devices with external auth handler
87e469be0c08 wireless: fix memory corruption bug when using vlans/station entries in the config
7277764bf817 bridge: rename "ifname" attribute to "ports"
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This can be used to handle network configuration of dynamically created vlan
interfaces in a more flexible way
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Bridge aggregates multiple ports so use a more accurate name ("ports")
and format (array) for storing them in board.json.
Example:
"network": {
"lan": {
"ports": [
"lan1",
"lan2",
"lan3",
"lan4"
],
"protocol": "static"
},
"wan": {
"ifname": "wan",
"protocol": "dhcp"
}
}
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Instead of adding all public signature keys from the openwrt-keyring
repository only add the key which is used to sign the master feeds.
If one of the other keys would be compromised this would not affect
users of master snapshot builds.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ZiKing CPE46B is a POE outdoor 2.4ghz device with an integrated directional
antenna. It is low cost and mostly available via Aliexpress, references can
be found at:
- https://forum.openwrt.org/t/anddear-ziking-cpe46b-ar9331-ap121/60383
- https://git.lsd.cat/g/openwrt-cpe46b
Specifications:
- Atheros AR9330
- 32MB of RAM
- 8MB of flash (SPI NOR)
- 1 * 2.4ghz integrated antenna
- 2 * 10/100/1000 ethernet ports (1 POE)
- 3 * Green LEDs controlled by the SoC
- 3 * Green LEDs controlled via GPIO
- 1 * Reset Button controlled via GPIO
- 1 * 4 pin serial header on the PCB
- Outdoor packaging
Flashing instruction:
You can use sysupgrade image directly in vendor firmware which is based
on OpenWrt/LEDE. In case of issues with the vendor GUI, the vendor
Telnet console is vulnerable to command injection and can be used to gain
a shell directly on the OEM OpenWrt distribution.
Signed-off-by: Giulio Lorenzo <salveenee@mortemale.org>
[fix whitespaces, drop redundant uart status and serial0, drop
num-chipselects, drop 0x1002 MAC address for wmac]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Remove vn call in favour of v call. This commit serves as preparation
for removing the v function call.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
[alter slightly to prevent double space after colon]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When building GRUB with binutils 2.35.2 or later, an error occurs due to
a section .note.gnu.property that is placed at an offset such that
objcopy needs to pad the img file with zeros. This in turn causes the
following error: "error: Decompressor is too big.".
The fix accepted by upstream patches a python script that isn't executed
at all when building GRUB with OpenWrt buildroot. There's another patch
that patches the files generated by that python script directly, but by
including it we would deviate further from upstream. Instead of doing
that, simply bump to the latest release candidate.
As one of the fixes for the CVEs causes grub to crash on some x86
hardware using legacy BIOS when compiled with -O2, filter -O2 and
-O3 out of TARGET_CFLAGS.
Fixes the following CVEs:
- CVE-2020-14372
- CVE-2020-25632
- CVE-2020-25647
- CVE-2020-27749
- CVE-2020-27779
- CVE-2021-3418
- CVE-2021-20225
- CVE-2021-20233
Runtime-tested on x86/64.
Fixes: FS#3790
Suggested-by: Dirk Neukirchen <plntyk.lede@plntyk.name>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
c44b40b overlay: fix syncronizing typo
b5397a1 fstools: block: fix segfault on mount with no target
bd7cc8d block: use dynamically allocated target string
6d8450e blockd: use allocated strings instead of fixed buffers
d47909e libblkid-tiny: fix buffer overflow
67d2297 block: match device path instead of assuming /dev/%s
2aeba88 block: allow autofs and umount commands also on MTD/UBI
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
28b162366d09 mt76: fix calling mt76_get_of_eeprom with an offset for pre-cal data
9d736545bb5a mt76: mt7915: disable pre-calibration support for now
Signed-off-by: Felix Fietkau <nbd@nbd.name>
6a6011d uclient-http: set eof mark when content-length is 0
19571e4 tests: fix help usage test for uclient built with sanitizer
c5fc04b tests: fix help usage test
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
PREFER_IPV4_ADDRESS is broken on IPv6-only hosts, as it causes busybox
utilities (ping, traceroute, ntpd) to forcibly use the A record instead of
the AAAA record when resolving a DNS name. This obviously fails when
there is no IPv4 connectivity. Since IPv6-only hosts or routers will only
become more common over time, disable PREFER_IPV4_ADDRESS to support this
use-case.
As a side-effect, disabling PREFER_IPV4_ADDRESS changes the default
resolution behaviour of busybox utilities on dual-stack hosts. Busybox
utilities now simply use the order given by getaddrinfo(), so they will
now prefer IPv6 addresses when resolving a name with both A and AAAA
records if there is IPv6 connectivity. This is in line with RFC 6724.
PREFER_IPV4_ADDRESS was likely intended to work around naive
implementations of getaddrinfo() that could return AAAA records first,
even on an IPv4-only host. But both musl (since 1.1.3) and glibc
correctly implement RFC 6724 for getaddrinfo() and check connectivity to
determine the correct order in which to return records. On IPv4-only
hosts, getaddrinfo() will return A records first, so there is no need for
the PREFER_IPV4_ADDRESS hack.
See also: https://bugs.busybox.net/show_bug.cgi?id=12381
Fixes: FS#84
Fixes: FS#2608
References: https://github.com/openwrt/openwrt/pull/4167
Signed-off-by: Alexander Traud <pabstraud@compuserve.com>
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Before this commit, it was assumed that mkhash is in the PATH. While
this was fine for the normal build workflow, this led to some issues if
make TOPDIR="$(pwd)" -C "$pkgdir" compile
was called manually. In most of the cases, I just saw warnings like this:
make: Entering directory '/home/.../package/gluon-status-page'
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
[...]
While these were only warnings and the package still compiled sucessfully,
I also observed that some package even fail to build because of this.
After applying this commit, the variable $(MKHASH) is introduced. This
variable points to $(STAGING_DIR_HOST)/bin/mkhash, which is always the
correct path.
Signed-off-by: Leonardo Mörlein <me@irrelefant.net>
Includes fix for CVE-2020-24588
c7dd54a22e30 mt76: connac: skip wtbl reset on sta disconnect
3511fd430356 mt76: validate rx A-MSDU subframes
aedc3145de6e mt76: fix possible NULL pointer dereference in mt76_tx
5c2baab92cd0 mt76: mt7615: fix NULL pointer dereference in tx_prepare_skb()
af21659ee834 mt76: mt76x0: use dev_debug instead of dev_err for hw_rf_ctrl
e423c16f16f7 mt76: mt7615: free irq if mt7615_mmio_probe fails
f2d0da8da9b7 mt76: mt7663: enable hw rx header translation
d2713a5d9de9 mt76: mt7921: fix mt7921_wfsys_reset sequence
ce5f32d84f33 mt76: mt7921: Don't alter Rx path classifier
8ab8c7747197 mt76: connac: fw_own rely on all packet memory all being free
a747b0bb4956 mt76: mt7921: enable deep sleep at runtime
2e6e999509b1 mt76: mt7921: add deep sleep control to runtime-pm knob
30bcb2338ce2 mt76: connac: fix WoW with disconnetion and bitmap pattern
56518f4a126e mt76: mt7921: consider the invalid value for to_rssi
e969ab10a034 mt76: mt7921: add back connection monitor support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
From the patch series description:
Several security issues in the 802.11 implementations were found by
Mathy Vanhoef (New York University Abu Dhabi), who has published all
the details at
https://papers.mathyvanhoef.com/usenix2021.pdf
Specifically, the following CVEs were assigned:
* CVE-2020-24586 - Fragmentation cache not cleared on reconnection
* CVE-2020-24587 - Reassembling fragments encrypted under different
keys
* CVE-2020-24588 - Accepting non-SPP A-MSDU frames, which leads to
payload being parsed as an L2 frame under an
A-MSDU bit toggling attack
* CVE-2020-26139 - Forwarding EAPOL from unauthenticated sender
* CVE-2020-26140 - Accepting plaintext data frames in protected
networks
* CVE-2020-26141 - Not verifying TKIP MIC of fragmented frames
* CVE-2020-26142 - Processing fragmented frames as full frames
* CVE-2020-26143 - Accepting fragmented plaintext frames in
protected networks
* CVE-2020-26144 - Always accepting unencrypted A-MSDU frames that
start with RFC1042 header with EAPOL ethertype
* CVE-2020-26145 - Accepting plaintext broadcast fragments as full
frames
* CVE-2020-26146 - Reassembling encrypted fragments with non-consecutive
packet numbers
* CVE-2020-26147 - Reassembling mixed encrypted/plaintext fragments
In general, the scope of these attacks is that they may allow an
attacker to
* inject L2 frames that they can more or less control (depending on the
vulnerability and attack method) into an otherwise protected network;
* exfiltrate (some) network data under certain conditions, this is
specific to the fragmentation issues.
A subset of these issues is known to apply to the Linux IEEE 802.11
implementation (mac80211). Where it is affected, the attached patches
fix the issues, even if not all of them reference the exact CVE IDs.
In addition, driver and/or firmware updates may be necessary, as well
as potentially more fixes to mac80211, depending on how drivers are
using it.
Specifically, for Intel devices, firmware needs to be updated to the
most recently released versions (which was done without any reference
to the security issues) to address some of the vulnerabilities.
To have a single set of patches, I'm also including patches for the
ath10k and ath11k drivers here.
We currently don't have information about how other drivers are, if
at all, affected.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support for querying and parsing SRV DNS records to nslookup_lede.c
This patch is based on http://lists.busybox.net/pipermail/busybox/2019-June/087359.html
Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
[reword subject, bump PKG_RELEASE]
Signed-off-by: Paul Spooren <mail@aparcar.org>
When the list of packages to be installed in a built image exceeds a certain
number, then 'opkg install' executed for target '$(curdir)/install' in
package/Makefile fails with: /usr/bin/env: Argument list too long.
On Linux, the length of a command-line parameter is limited by
MAX_ARG_STRLEN to max 128 kB.
* https://elixir.bootlin.com/linux/latest/source/include/uapi/linux/binfmts.h#L15
* https://www.in-ulm.de/~mascheck/various/argmax/
To solve the problem, store the package list being passed to 'opkg install'
in a temporary file and use the shell command substitution to pass the
content of the file to 'opkg install'. This guarantees that the length of
the command-line parameters passed to the bash shell is short.
The following bash script demonstrates the problem:
----------------------------------------------------------------------------
count=${1:-1000}
FILES=""
a_file="/home/egorenar/Repositories/openwrt-rel/bin/targets/alpine/generic/packages/base-files_1414-r16464+19-e887049fbb_arm_cortex-a15_neon-vfpv4.ipk"
for i in $(seq 1 $count); do
FILES="$FILES $a_file"
done
env bash -c "echo $FILES >/dev/null"
echo "$FILES" | wc -c
----------------------------------------------------------------------------
Test run:
----------------------------------------------------------------------------
$ ./test.sh 916
130989
$ ./test.sh 917
./test.sh: line 14: /bin/env: Argument list too long
131132
----------------------------------------------------------------------------
Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
[reword commit subject]
Signed-off-by: Paul Spooren <mail@aparcar.org>
