Remove unnecessary 'if' macros for previous kernel versions.
After removing kernel 6.1 the kernel is always >= 6.6 so the conditions
are unnecessary.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[removed some more and also no longer include version.h]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Remove unnecessary 'if' macros for previous kernel versions.
After removing kernel 6.1 the kernel is always >= 6.6 so the conditions
are unnecessary.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import pending patch to fix the cmdline parsing of the "blkdevparts="
parameter which has been broken somewhen between Linux 6.1 and Linux 6.6.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that 6.6 is the default, remove the 6.1 config and the hack that
was required for the arm32 DTS dir change.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
AVM FRITZ!Repeater 1200 does not use QCA807x PHY at all and thus it
disables all of the individual PHY nodes, however this is not enough
anymore since the conversion to PHY package.
Now its now enough to disable the PHY-s in the package alone, but the PHY
package node itself must also be disabled.
Fixes: 1b931c33a2 ("ipq40xx: adapt to new Upstream QCA807x PHY driver")
Fixes: #15355
Link: https://github.com/openwrt/openwrt/pull/15365
Signed-off-by: Robert Marko <robimarko@gmail.com>
It appears that the CFE boot loader found in the XG6846
cannot load kernels over a certain size, and the old
relocate hack is not working.
What to do? We can build a small U-Boot into the image,
make CFE boot that, place the kernel immediately after
U-Boot, and use U-Boot to boot the system instead.
The compiled u-boot.bin becomes around ~300KB and with
LZMA compression it will swiftly fit into 128KB, so
we use two 64KB erase blocks right after the CFE to
store an imagetag:ed U-Boot.
Reviewed-by: Paul Donald <newtwen+github@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a device tree and build options for the XG6846
switch/router to the BMIPS target.
Hardware:
- SoC: Broadcom BCM6328
- CPU: BMIPS4350 V7.5
- RAM: 64 MB DDR
- NOR Flash: 16 MB parallel (CFE and OS)
- Ethernet LAN: 4x 1Gbit
- Ethernet WAN: 2x 1Gbit, fiber and TP
- Buttons: reset
- LEDs: 7 or 8, power and USB LEDs are GPIO-based, the
LAN LEDs are controlled by the Marvell DSA Switch.
- USB: on some versions
- UART: yes
The device ODM (original device manufacturer) is XAVi
http://www.xavi.com.tw/
It is possible to boot the initramfs version
openwrt-bmips-bcm6328-inteno_xg6846-initramfs.elf from
CFE by interrupting the boot on the UART console and downloading
it from a TFTP server e.g.:
CFE> r 192.168.1.2:openwrt-bmips-bcm6328-inteno_xg6846-initramfs.elf
Installation to target flash is not possible using CFE because
the image becomes too big for the CFE version found in these
devices. A separate U-Boot two-stage solution exists for
actually booting the device.
This device is called a "managed ethernet switch" by the vendor
and "media converter" or "fiber modem" by some of the ISPs
using it: the main purpose is to convert fiber connections to
ethernet, most devices just act as switches bridging the
fiber SFP to ethernet TP.
The device has a Marvell MV88E6352 DSA switch managed by
a BCM6328 BMIPS SoC.
This port makes it possible to use the XG6846 to grab an IP
number from the fiber connection and use all four LAN
connections out, turning it into a proper router.
This support is based mostly on the observations by the people on
the forum thread "Help with Inteno XG6846" where users NPeca75,
mrhaav, systemcrash and csom helped out to reverse engineer the
device. Then I made it work on the BMIPS target, figured out
the two-level switch hierarchy and settings.
Link: https://forum.openwrt.org/t/help-with-inteno-xg6846/68276/14
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since we split the Inteno XG6846 "firmware" partition with the
uImage MTD splitter, we need to compile in support for this
splitting method into the BCM6328.
Reviewed-by: Paul Donald <newtwen+github@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit [ca8c30208d5e][1] updates procd to handle muliple "console=" on the
kernel command line. This affects Raspberry Pi builds because cmdline.txt
specifies a UART console and a virtual console on HDMI, in that order.
When procd finds multiple consoles on the command line, it attempts to
open /dev/console. Linux uses the [last console][2] for /dev/console, so
procd opens the virtual console on Raspberry Pi. This completely disables
the UART console and causes [strange behavior][3] on the virtual console.
Prior to ca8c30208d5e, procd would always open the first console, which is
the UART console.
The simplest fix without reverting ca8c30208d5e is to swap the order of
console options in cmdline.txt. By putting the UART console last, procd
handles the serial console correctly as before.
[1]: https://git.openwrt.org/?p=project/procd.git;a=commit;h=ca8c30208d5e1aaa2c0e3f732c4c9944735e9850
[2]: https://www.kernel.org/doc/html/latest/admin-guide/serial-console.html
[3]: https://forum.openwrt.org/t/rasberry-pi-4-model-b-keyboards-gone-wild/195594
Signed-off-by: Elbert Mai <code@elbertmai.com>
Currently, the MT7530 DSA subdriver configures the MT7530 switch to provide
direct access to switch PHYs, meaning, the switch PHYs listen on the MDIO
bus the switch listens on. The PHY muxing feature makes use of this.
This is problematic as the PHY may be attached before the switch is
initialised, in which case, the PHY will fail to be attached.
Since commit 91374ba537bd ("net: dsa: mt7530: support OF-based registration
of switch MDIO bus") on mainline Linux, we can describe the switch PHYs on
the MDIO bus of the switch on the device tree.
When the PHY is described this way, the switch will be initialised first,
then the switch MDIO bus will be registered. Only after these steps, the
PHY will be attached.
Describe the switch PHYs on mt7621.dtsi and remove defining the switch PHY
on the SoC's mdio bus node. When the PHY muxing is in use, the interrupts
for the muxed PHY won't work, therefore delete the "interrupts" property on
the devices where the PHY muxing feature is in use.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
The ethernet-phy@4 node doesn't exist for WAVLINK WL-WN573HX1. Remove it
and the duplicate gmac0 node.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Currently, the pinctrl-0 property on the ethernet node is modified to
exclude the rgmii1 and rgmii2 pin groups to be claimed with rgmii1 and
rgmii2 functions, respectively. Remove the modification of this property as
we need these pin groups to be claimed with the said functions for this
device.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
1. Enable this feature only for 32-bit CPUs as MIPS64 can not
access the full range unmapped uncached memory.
2. Backport this fix to the 6.1 old LTS kernel.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
There was no config in the uboot-envtools package, so there is no
generated /etc/fw_env.config for the fw_printenv and fw_setenv utils.
Since uboot-envtools 2024.01, there is a way to make these utils work
without /etc/fw_env.config if the DT has an env partition with the prop.:
compatible = "u-boot,env";
So, this commit adds the prop. above to the appsblenv:0 partition
in the yuncore ax880 DTS file.
Signed-off-by: Isaev Ruslan <legale.legale@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15305
Signed-off-by: Robert Marko <robimarko@gmail.com>
Turn on SoC pull-ups on I2C pins, since there are no discrete pull-up
resistors on the bus.
Increase clock to 400 kHz. Both chips on the bus support 400 kHz. I
tested the ISL28022 at 4,000 reads/sec and didn't see any garbled output
or bus hangs, even with SoC drive strength reduced to 2 for the test.
Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15334
Signed-off-by: Robert Marko <robimarko@gmail.com>
ipq60xx bootcount script include /lib/functions that produce warning
when the script is enabled on image compilation. This script is already
included by /etc/rc.common hence it's not needed.
While at it also fix the format of the switch case.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Convert the Enterasys WS-AP3710i access point to use the simpleImage
wrapper.
This is necessary, as the bootlaoder does not align the DTB correctly
(and does not support altering the FDT loadaddress). Booting images with
kernels 5.15 and later can break depending on the alignment on the DTB
within the FIT image.
Signed-off-by: David Bauer <mail@david-bauer.net>
This refreshes the configuration on top of kernel 6.6 and activates it
as test kernel configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Despite coming with multiple I2C EEPROMs supposedly dedicated for that
purpose, the BPi-R4 does not seem to have factory assigned MAC addresses.
Hence, just like for all other BPi boards, store a randomly generated
MAC address on first boot and derive WAN and Wi-Fi MAC addresses from
that as well. Not perfect, but better than random on every boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow selecting 6.1 as testing kernel on zynq.
Tested-by: Luis Araneda <luaraneda@gmail.com> # Zybo Z7-20
Signed-off-by: Nick Hainke <vincent@systemli.org>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Nick Hainke <vincent@systemli.org>
