Commit Graph

1193 Commits

Author SHA1 Message Date
Hauke Mehrtens
f8b93e2d12 mediatek: filogic: Migrate wifi configuration device paths
The device path to the devices changed. Migrate the wifi
configurations from the old path to the new one. This is needed to
migrate Wireless configurations from OpenWrt 23.05 to OpenWrt 24.10.

This script is based on these two files:
target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate

Fixes: 0ef9274721 ("mediatek: filogic: move mt7981 on-SoC blocks to "soc" node in DT")
Fixes: https://github.com/openwrt/openwrt/issues/17174
Link: https://github.com/openwrt/openwrt/pull/17210
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-12-10 00:02:27 +01:00
Ondřej Niesner
a498a84393 mediatek: filogic: prevent faulty mac address assignment
The vendor U-Boot on the Cudy WR3000 assign random mac addresses on boot
and set the 'local-mac-address' property which prevents Openwrt from
assigning the correct address from evmem.

This patch removes the alias for ethernet0 so that U-Boot doesn't add
the property.

Related to: a55ab9e134 ("mediatek: filogic: prevent faulty mac address assignment")
Fixes: https://github.com/openwrt/openwrt/issues/15587
Signed-off-by: Ondřej Niesner <ondra.niesner@seznam.cz>
Link: https://github.com/openwrt/openwrt/pull/17201
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-12-09 23:57:12 +01:00
Maxim Anisimov
d087a79b7b mediatek/filogic: add Keenetic KN-3811 support
Specification:
 * Mediatek MT7981BA
 * 256 MB SPI-NAND
 * 512 MB DDR4 RAM
 * MT7976CN DBDC AX Wi-Fi
 * MediaTek MT7531AE (3x LAN Gigabit ports) + Internal Gbe Phy (1x WAN Gigabit port)
 * 4x LED (power, internet, fn, wifi)
 * 3x buttons (wps, fn, reset)
 * 1x USB 3.0 port

Serial Interface:
 * 3 Pins GND, RX, TX
 * Settings: 115200, 8N1

Notes:
 * The device supports dual boot mode
 * Fn led reassigned to wlan 2.4

Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-mediatek-filogic-keenetic_kn-3811-squashfs-factory.bin"
   to "KN-3811_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
   the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17135
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-12-08 19:52:35 +01:00
Bohdan Chubuk
5348e2e81a
generic: mtd: spinand: add support for FORESEE F35SQA002G
Add support for FORESEE F35SQA002G SPI NAND.
Datasheet:
  https://www.longsys.com/uploads/LM-00006FORESEEF35SQA002GDatasheet_1650183701.pdf

Refresh all affected patch with make target/linux/refresh.

Signed-off-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Bohdan Chubuk <chbgdn@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16915
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-12-06 14:38:53 +01:00
John Crispin
5c12fe45b9 target/metadata: set OpenWrt One as the default menuconfig target/profile
Signed-off-by: John Crispin <john@phrozen.org>
2024-12-02 13:55:36 +01:00
John Crispin
f342255025 mediatek: filogic: enable CONFIG_LEDS_TRIGGER_PATTERN
The boot LED on OpenWrt One is PWM driven and sets the pattern trigger as the
default inside its devicetree.

Signed-off-by: John Crispin <john@phrozen.org>
2024-12-02 13:55:36 +01:00
Mikhail Zhilkin
ee8df790ca mediatek: MERCUSYS MR90X v1: add OpenWrt U-Boot (UBI) layout
This commit adds OpenWrt U-Boot (UBI) layout support for MERCUSYS MR90X
v1.

Stock U-Boot UBI size:   50 MiB
OpenWrt U-boot UBI size: 126 MiB

Install
-------
1. Perform steps 1-14 of the OpenWrt installation guide (use OpenWrt
   initramfs-recovery.itb instead of initramfs-kernel.bin at the step 10,
   12 and 14).
Link: https://openwrt.org/toh/mercusys/mr90x_v1#installation

2. Make backups:
```
cat /dev/mtd0 > /tmp/boot.bin
cat /dev/mtd5 > /tmp/tp_data.bin
```
   Copy /tp_data dir content, /tmp/boot.bin and /tmp/tp_data.bin and to
   your PC using scp. You can also backup the remaining partititons. Copy
   backups to a safe place, they are required for the next steps and stock
   firmware recovery.

3. Reboot to OpenWrt initramfs:
```
reboot
```

4. Copy OpenWrt ubi-bl31-uboot.fip, ubi-preloader.bin,
   ubi-squashfs-sysupgrade.itb and MT7986_EEPROM.bin, default-mac (from
   /tp_data backup) to the /tmp folder of the router using scp.

5. Prepare UBI:
```
ubidetach -p /dev/mtd3; ubiformat /dev/mtd3 -y; ubiattach -p /dev/mtd3
ubimkvol /dev/ubi0 -N fip -t static -s 1MiB
ubiupdatevol /dev/ubi0_0 /tmp/ubi-bl31-uboot.fip
ubimkvol /dev/ubi0 -N ubootenv -s 0x1f000
ubimkvol /dev/ubi0 -N ubootenv2 -s 0x1f000
```

6.  Install kmod-mtd-rw and unlock partitions:
```
opkg update && opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd unlock boot
mtd unlock bl2
mtd unlock factory
```

7. Prepare "factory" partition:
```
dd if=/dev/zero bs=$((0x8000)) count=1 | tr '\000' '\377' > /tmp/factory.bin
dd if=/tmp/MT7986_EEPROM.bin of=/tmp/factory.bin conv=notrunc
dd if=/tmp/default-mac >> /tmp/factory.bin
```

8. Write "factory" partition:
```
mtd erase factory
mtd write /tmp/factory.bin factory
```

9. Write preloader partition:
```
mtd erase bl2
mtd write /tmp/ubi-preloader.bin bl2
```

10. Write OpenWrt sysupgrade image:
```
sysupgrade -n /tmp/ubi-squashfs-sysupgrade.itb
```

Recovery
--------
1. Place OpenWrt initramfs-recovery.itb image (with original name) on the
   tftp server (IP: 192.168.1.254).
2. Press "reset" button and power on the router. After ~10 sec release the
   button.
3. Use OpenWrt initramfs system for recovery.

BL2 and FIP recovery
--------------------
Use mtk_uartboot and UART connetion if BL2 or FIP in UBI is destroyed:
Link: https://github.com/981213/mtk_uartboot
Link: https://openwrt.org/toh/mercusys/mr90x_v1#serial

Return to stock:
----------------
1. Copy "boot" partition backup (boot.bin) to the /tmp dir of the router
   using scp.

2. Install kmod-mtd-rw:
```
opkg update && opkg install kmod-mtd-rw
```

3. Restore stock U-Boot:
```
   insmod mtd-rw i_want_a_brick=1
   mtd unlock boot
   mtd erase boot
   mtd write /tmp/boot.bin boot
```

4. Erase UBI and reboot:
```
mtd erase ubi
reboot
```

5. Open U-Boot web recovery, upload stock firmware image and start
   upgrade.
Link: http://192.168.1.1

6. Complete steps 1-9 of the OpenWrt installation guide to get root
   rights.
Link: https://openwrt.org/toh/mercusys/mr90x_v1#installation

7. Upload "tp_data" partition backup (tp_data.bin) to the /tmp folder of
   the router using scp.

8. Restore stock calibrations:
```
mtd write /tmp/tp_data.bin tp_data
reboot
```

9. Perform "factory restore" via stock firmware web interface.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-30 18:36:05 +01:00
Maxim Anisimov
5a4eb56a7b mediatek/filogic: add Keenetic KN-3911 support
Specification:
 - MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
 - 512MB RAM
 - 128MB SPI NAND
 - 2 LEDs (green, orange)
 - 3 buttons (fn, reset, wps)
 - 2 2.5Gbit ethernet ports based on Airoha EN8811H phy

Serial Interface:
 - 3 Pins GND, RX, TX
 - Settings: 115200, 8N1

Notes:
 - The device supports dual boot mode

Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-mediatek-filogic-keenetic_kn-3911-squashfs-factory.bin"
   to "KN-3911_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
   the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16830
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-28 22:33:21 +01:00
Maxim Anisimov
0d651dd302 mediatek/filogic: enable mtd virtual concat support
This is required for upcoming Keenetic KN-3911 support

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16830
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-28 22:33:21 +01:00
Petr Štetiar
30ae0b3f1e
mediatek: filogic: Cudy WR3000S v1: fix CRLF line endings
DTS file for this device seems to be using CRLF line endings, so lets
convert them into Unix-style LF.

Fixes: faf4b3e0f7 ("mediatek: filogic: add support for Cudy WR3000S v1")
Link: https://github.com/openwrt/openwrt/pull/17096
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2024-11-28 21:19:47 +00:00
George Oldfort
e44180d45c mediatek: filogic: add KTD2026/7 driver to Acer Connect Vero W6m
This commit adds kmod-leds-ktd202x to the OpenWrt image for the device
"Acer Connect Vero W6m" which is equipped with one KTD2026 controlling the
device's status LED via I2C.

Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16860
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-28 21:59:58 +01:00
George Oldfort
1bdb6d8404 mediatek: remove ktd-202x driver filogic image (Aer Vero W6m)
Image build fails with PR #16861 merged while PR #16860 not merged.

Removing kmod-leds-ktd202x from filogic.mk will fix the build process.

Fixes: 2898d1d126 ("mediatek: add support for Acer Predator W6d and Acer Vero W6m")
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/17087
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-26 10:43:16 +01:00
Mikhail Zhilkin
d413163832 mediatek: Routerich AX3000: add OpenWrt U-Boot layout
This commit adds OpenWrt U-Boot layout support for Routerich AX3000. The
aims:
1. Get open-source U-Boot;
2. Get maximum available free space in OpenWrt.

Install
-------
1. Copy OpenWrt ubootmod-bl31-uboot.fip, ubootmod-preloader.bin, to the
   /tmp folder of the router using scp.

2. Make mtd partitions backups:
   http://192.168.1.1/cgi-bin/luci/admin/system/flash -> Save mtdblock
   contents

3. Install kmod-mtd-rw:
```
opkg update && opkg install kmod-mtd-rw
```

4. Write FIP and preloader:
```
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd erase BL2
mtd write /tmp/ubootmod-preloader.bin BL2
mtd unlock FIP
mtd erase FIP
mtd write /tmp/ubootmod-bl31-uboot.fip FIP
```

5. Copy OpenWrt ubootmod-initramfs-recovery.itb to the tftp server root
   with IP 192.168.1.254.

6. Reboot router:
```
reboot
```
U-Boot will automatically download from the tftp server and boot OpenWrt
initramfs system.

7. Copy OpenWrt ubootmod-squashfs-sysupgrade.itb to the /tmp dir of the
   router using scp.

8. Run sysupgrade:
```
sysupgrade -n /tmp/squashfs-sysupgrade.itb
```

Recovery
--------
1. Place OpenWrt initramfs-recovery.itb image (with original name) on the
   tftp server (IP: 192.168.1.254).
2. Press "reset" button and power on the router. After ~10 sec release the
   button.
3. Use OpenWrt initramfs system for recovery.

BL2 and FIP recovery
--------------------
Use mtk_uartboot and UART connection if BL2 or FIP in UBI is destroyed:
Link: https://github.com/981213/mtk_uartboot

Return to stock:
----------------
1. Copy partition backups (BL2.bin and FIP.bin) to the /tmp dir of the
   router using scp.

2. Install kmod-mtd-rw:
```
opkg update && opkg install kmod-mtd-rw
```

3. Restore stock U-Boot and reboot:
```
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd erase BL2
mtd write /tmp/BL2.bin BL2
mtd unlock FIP
mtd erase FIP
mtd write /tmp/FIP.bin FIP
reboot
```

4. Open U-Boot web recovery, upload stock firmware image and start
   upgrade.
Link: http://192.168.1.1

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16791
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-24 23:41:02 +01:00
David Ignjic
faf4b3e0f7 mediatek: filogic: add support for Cudy WR3000S v1
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
128MB SPI-NAND (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
UART: 115200 8N1 3.3V

MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set

Installation
------------

1. Connect to the serial port as described in the "Hardware" section.

2. Power on the device + press reset pin. Keep pressing reset pin to enter the U-Boot  shell.

3. Download the OpenWrt initramfs image. Place it on an TFTP server
   connected to the Cudy LAN ports. Make sure the server is reachable at
   192.168.1.88. Rename the image to "cudy3000s.bin"

4. Download and boot the OpenWrt initramfs image.

   $ tftpboot 0x46000000 cudy3000s.bin; bootm 0x46000000

5. Transfer the OpenWrt sysupgrade image to the device using scp.
   Install with sysupgrade.

Signed-off-by: David Ignjic <ignjic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-23 20:24:57 +01:00
David Bauer
b8b658bc0d mediatek: fix Cudy AP3000 Outdoor label-mac
The label-mac does not match the one assigned to the ethernet interface.
Use the mac-address assigned to the wifi interface instead, as it
matches the one found on the device label.

Signed-off-by: David Bauer <mail@david-bauer.net>
2024-11-23 20:04:01 +01:00
George Oldfort
2898d1d126 mediatek: add support for Acer Predator W6d and Acer Vero W6m
This commit adds support for two variants of the already supported router
Acer Predator Connect W6: The Acer Predator Connect W6d (W6 without 6 GHz
wifi) and the Acer Connect Vero W6m (W6 without 2.5G eth1 port, usb3 port,
and the 6 on-board gpio RGB LEDs, and with a KTD2026 RGB LED controller
instead of the KTD2061 LED controller of the W6/W6d).

The device tree for the W6m refers to the KTD202x driver suggested in
PR #16860.

Patching target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
removes the code repetition in (old) lines 121 to 124 on the occasion.

This is the last of four commits into which the original commit was split
to make reviews easier and more targeted.

Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-23 19:33:42 +01:00
George Oldfort
d42075dcef mediatek: improve device tree for Acer Predator Connect W6
In order to prepare for OpenWrt support other Acer W6 devices and to get
a step further to full hardware support for Acer Predator Connect W6, this
commit
- adjusts the product name ("Acer Predator Connect W6")
- updates gpio LED labels to function/color scheme
- show router status by using first rgb led instead of it's red color only
  (blue: booting/failsafe mode; red: sysupgrade; green: running – was: red)
- changes switch/eth1 led configuration to reflect RX/TX activity and speed
  (green: full 1Gbps/2.5Gbps speed; amber: lower speed; blink: RX/TX)
- shortens dummy dm-mod.create string in bootargs
- enables W6's i2c interface

This is the third of four commits into which the original commit was split
to make reviews easier and more targeted.

Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-23 19:33:42 +01:00
George Oldfort
e7aaba2587 mediatek: make use of Acer Predator Connect W6's u-boot environment
In order to prepare OpenWrt support for other Acer W6 devices and to adapt
the procedure to read and set mac addresses which other devices of the same
target are using (instead of needing an additional script and creating an
additional structure in the file system), this commit
- reads device mac addresses from u-boot environment
- avoids the detour via the file system to set the mac addresses
- drops redundant file /lib/preinit/05_extract_factory_data.sh

The idea and the implementation were thankfully taken from PR #16410.

This is the second of four commits into which the original commit was split
to make reviews easier and more targeted.

Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-23 19:33:42 +01:00
George Oldfort
ce3b36b3d5 mediatek: split Acer/W6 dts into W6 common dtsi and device specific dts
In order to prepare OpenWrt support for other Acer W6 devices, this commit
moves all device tree components that are used by all Acer W6/W6e/W6d/W6m
routers from mt7986a-acer-predator-w6.dts to mt7986a-acer-w6-common.dtsi
(new file) and includes this dtsi file in mt7986a-acer-predator-w6.dts.

Minor changes had to be made to the device tree in order to improve clarity
and – notably – to reduce the number of dtc warnings:
- replace (obviously wrong) led@<N> gpio led entities by led-<N>
- remove unnecessary (default-state = "off") gpio led statements
- rename entity “memory” to “memory@0”
- add missing #address-cells and #address-size in /soc/mmc@11230000
- add missing #address-cells and #address-size in /soc/pcie@11280000
- introduce symbols “nvmem” and “swport0” in dtsi (referenced in dts)

The changes were checked with `diff -BEZbdtwy --suppress-common-lines ...`
(comparing two dts files created using old and new fdt-1 blobs again), see
https://github.com/openwrt/openwrt/pull/16861/#issuecomment-2455680020 .

This is the first of four commits into which the original commit was split
to make reviews easier and more targeted.

Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-23 19:33:42 +01:00
Romanov Danila
d8a9669093 mediatek: change Routerich AX3000 ubi size
All new routers are shipped with ubi size 112MB since early September.
Bootloader update required (ask vendor , see wiki)

These partitions weren't used:
firmware_backup
zrsave
config2

Signed-off-by: Romanov Danila <pervokur@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16686
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-23 15:42:24 +01:00
Robert Marko
52b6c92479 Revert "mediatek: fix pwn fan settings for sinovoip bpi-r3"
This reverts commit 3467ea905b.

I merged it by accident.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-11-21 22:04:41 +01:00
Mikhail Kshevetskiy
3467ea905b mediatek: fix pwn fan settings for sinovoip bpi-r3
Popular bpi-r3 pwm fans like this one

  https://www.amazon.com/youyeetoo-Barebone-Fan-BPI-R3-Integrated/dp/B0CCCTY8PS

will not work properly with current openwrt-23.05/24.10 firmware.
Trying different pwm setting

  echo $value > /sys/devices/platform/pwm-fan/hwmon/hwmon1/pwm1

I found:

  pwm1 value     fan rotation speed   cpu temperature     notes
  -----------------------------------------------------------------
    0            maximal              31.5 Celsius        too noisy
   40            optimal              35.2 Celsius        no noise hearable
   95            minimal
   above 95      does not rotate      55.5 Celsius
  -----------------------------------------------------------------

At the moment we have following cooling levels:

  cooling-levels = <255 96 0>;

for cpu-active-high, cpu-active-medium and cpu-active-low modes correspondingly.
Thus only cpu-active-high and cpu-active-low are usable. I think this is wrong.

This patch fixes cpu-active-medium settings for bpi-r3 board.

PS: I know, the patch is not ideal as it can break pwm fan for some users.
    There are some peoples that use handmade cooling solutions, but:
      * discussed cooler is the only 'official' pwm cooler for bpi-r3
        available on the market.
      * most peoples will use passive cooling available on the market or
        the discussed cooler.
      * the pwm-fan dts section was added before the official cooler
        appears on the market.
    Thus it should not be a lot of harm from this fix.

Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16974
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-11-21 22:04:14 +01:00
Rosen Penev
cd92cbddf8 kernel: filter out compiler opts from config
These get dynamically set based on compiler version. Not relevant for
targets.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16770
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-17 14:55:16 +01:00
Rosen Penev
da8abd4a1e kernel: remove GCC11_NO_ARRAY_BOUNDS
This symbol is no longer present.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16770
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-17 14:55:16 +01:00
John Audia
487ca61f91 kernel: bump 6.6 to 6.6.61
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.61

Manually rebased:
	bcm27xx/patches-6.6/950-0998-i2c-designware-Add-support-for-bus-clear-feature.patch

All other patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16959
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-11-16 00:25:14 +01:00
Enrico Mioso
b43194e041 mediatek: filogic: add support for GatoNetworks GDSP
The GatoNetworks GDSP is a re-branded version of the R5000 5G Industrial
router from Yinghua Technologies.
The re-branded device comes with OpenWrt preinstalled, and an OpenWrt-based
U-Boot bootloader version. While the flash layout has been kept compatible
with the OpenWrt version found on the stock device (see [5]), the image format
changed, making a bootloader upgrade necessary.

Specifications:
SoC: Mediatek MT7981BA
RAM: 256MB
Flash: SPI-NOR 32 MiB (Winbond W25Q256)
WLAN: MT7976CN DBDC AX Wi-Fi
Switch: MT7531AE (4x LAN Gigabit ports, 1x WAN Gigabit port)
5G: Quectel RM520N modem
Watchdog: an external WDT connected to GPIO 6 is present and always running;
          the built-in Mediatek watchdog is also present and effective, but
          not used at the moment.

This porting has been tested only with 1x 5G modems installed (the device
supports up to two).

Installation:
Installation is possible via sysupgrade both in the stock device and
re-branded version. However, in the former case, updating the bootloader is
required.

OpenWrt-based U-Boot Bootloader installation
--------------------------------------------
The firmware flashed in the re-branded device at manifacturing time will
flash an OpenWrt-based U-Boot bootloader with some extra recovery features
(see [1]) at first boot.
To update the bootloader, you need to install the mtd-rw module and
insmod it:

insmod mtd-rw i_want_a_brick=1

Then update relevant flash partitions:

mtd erase u-boot-env
mtd erase BL2
mtd erase FIP
mtd write openwrt-mediatek-filogic-gatonetworks_gdsp-preloader.bin BL2
mtd write openwrt-mediatek-filogic-gatonetworks_gdsp-bl31-uboot.fip FIP

And reboot, making sure all previous commands ran succesfully.
If something goes wrong, you can recover your device via the mtk_uartboot
tool.
In my testing, it was possible to start the process even without (un)-plugging
the device, may be handy for remote recovery.

Installation from stock device and firmware
-------------------------------------------
To install vanilla OpenWrt in the stock device (R5000 5G Industrial router
from Yinghua Technologies) running the stock vendor firmware, you will need
to update your bootloader as described in previous section. Remember to use
-F (force upgrade) and -n (not keeping settings).

U-Boot Recovery
---------------
This procedure has been tested only with the OpenWrt-based U-boot bootloader.
Assign your system static IP address 192.168.1.1 and start a TFTP server. The
device will look for an initramfs image named
openwrt-mediatek-filogic-gatonetworks_gdsp-initramfs-kernel.bin
(so you may use openwrt/bin/targets/mediatek/filogic as root dir for your
TFTP server).
Power on the device while keeping the reset button pressed, until you see
a TFTP request from 192.168.1.10. Your environment will be restored to it's
default state.

MAC addresses assignment
------------------------
MAC addresses are assigned slightly differently than in stock firmware. In
particular, the 5 GHz Wi-Fi uses 2.4 GHZ MAC + 1, rather than reusing it with
LA bit set as done in stock firmware. This MAC address is allocated to the
device, so it can be used.
The 2.4 GHz Wi-Fi MAC address is the label MAC. LAN MAC is used to set the
special U-Boot environment ethaddr variable.

device					MAC address		U-Boot env variable		factory partition offset
2.4 GHz Wi-Fi		:84						wifi_mac							0x4
5.8 GHz Wi-Fi		:85						not present						not present
WAN							:86						wan_mac								0x24
LAN							:87						lan_mac								0x2A

Notes
-----
[1]: the OpenWrt-based U-Boot bootloader you will find installed in the
re-branded device is configured to request for the initramfs image via
TFTP for $gdsp_tftp_tries times before trying normal boot from NOR flash.
Setting this U-Boot environment variable to 0x0 will disable the feature,
which is not implemented in this patch.
[2]: the exposed UART port is connected to ttyS1; the ttyS0 console port is
not exposed.
[3]: the provided bootloader environment has no provision for operating on
BL2 and the FIP partitions. This is an intentional choice to make it
(slightly) more difficult to brick the device.
[4]: it seems GPIO 6 is used both for the "SYS" LED and external WDT.
[5] BL2 expects to find FIP payload at a fixed offset, so some constraints
apply.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
2024-11-14 04:14:23 +00:00
Rosen Penev
cc98cfafd7
treewide: remove THIS_MODULE assignment
Matches upstream coccinelle check: api/platform_no_drv_owner.cocci.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16846
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2024-11-10 02:16:31 +01:00
John Crispin
48028cd102 mediatek: set 7 MACs per wifi band in board.json on OpenWrt One
Mass production units will get 16 assigned MAC addresses. This allows each phy
to spawn up to 7 VAPs which will each have unique MAC without needing the
private bit.

Signed-off-by: John Crispin <john@phrozen.org>
2024-11-05 10:11:44 +01:00
John Crispin
6ec1477b4d mediatek: set mac increment to 7 for the 5G radio on OpenWrt One
Mass production units will get 16 assigned MAC addresses. This allows each phy
to spawn up to 7 VAPs which will each have unique MAC without needing the
private bit.

Signed-off-by: John Crispin <john@phrozen.org>
2024-11-05 10:11:44 +01:00
Leon M. Busch-George
d64e1ed421 mediatek: YunCore AX835: fix voltage regulator
Specifying GPIO_ACTIVE_HIGH on the GPIO for the voltage regulator doesn't
suffice. The regulator itself requires enable-active-high to be set.

Fixes: #16292
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Link: https://github.com/openwrt/openwrt/pull/16839
Signed-off-by: Robert Marko <robimarko@gmail.com>
2024-11-03 21:40:53 +01:00
Daniel Golle
675d7c8849 mediatek: refresh patches
The mediatek target requires refreshing after recent additions.

Fixes: cfe8e6e75f ("mediatek: add support for Realtek RTL8261n 10G PHYs")
Fixes: ddfae94a14 ("mediatek: add support for swapping the polarity on usxgmii interfaces")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-11-03 02:39:58 +00:00
Daniel Golle
591272d197 mediatek: filogic: BPi-R4: wire up pinctrl for pwm-fan
Assign pwm function of PWM0 pin to the pwm-fan.
This is mostly just cosmetics as it basically reflects the default
setting of that pin.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-11-02 22:37:34 +00:00
Daniel Golle
2cbd230091 mediatek: pinctrl-mt7988: add missing PWM pingroups
Add additionals possible pinctrl group for pwm2~7 on pins
pin  4 (GPIO_A)        pwm7
pin 58 (JTAG_JTDI)     pwm2
pin 59 (JTAG_JTDO)     pwm3
pin 60 (JTAG_JTMS)     pwm4
pin 61 (JTAG_JTCLK)    pwm5
pin 62 (JTAG_JTRST_N)  pwm6

They can be useful e.g. on the BPi-R4 as in that way pwm2~6 can be exposed
on the 26-pin header (pwm6 always, pwm2~5 instead of the full UART).

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-11-02 22:37:34 +00:00
John Crispin
a85f11f191 mediatek: filogic: add Arcadyan Mozart platform
* Mediatek MT7988A (4x Cortex-A73, up to 1.8 GHz clock speed)
* 8 GiB eMMC
* 4 GiB DDR4 RAM
* 2x 10000M + 1x 1000M  ports
* MT7996 Tri-band (2.4G, 5G, 6G) 4T4R 802.11be Wi-Fi
* 2 buttons (Reset, WPS)
* 2x LED for each GMAC
* USB-C PD power input

Signed-off-by: John Crispin <john@phrozen.org>
2024-11-01 07:43:00 +01:00
John Crispin
ddfae94a14 mediatek: add support for swapping the polarity on usxgmii interfaces
This patch comes from the MTK SDK.

Signed-off-by: John Crispin <john@phrozen.org>
2024-11-01 07:43:00 +01:00
John Crispin
cfe8e6e75f mediatek: add support for Realtek RTL8261n 10G PHYs
There is no upstream driver yet. Merge the RTL SDK driver for now.

Signed-off-by: John Crispin <john@phrozen.org>
2024-11-01 07:43:00 +01:00
Daniel Golle
2b173ab730 mediatek: mt7988: fix peripheral SPI busses
The clocks for SPI busses were named wrongly which resulted in the
spi-mt65xx driver not requesting them. This has apparently been
worked around by marking the clocks required for SPI0 which is used
for SPI-NOR and SPI-NAND flash chips as critical.
Fix the device tree for all 3 generic SPI host controllers and no
longer mark clocks as critical.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-11-01 03:40:36 +00:00
Daniel Golle
388de64d9f mediatek: mt7988: add DT entries for WED
Add memory regions and devices used for wireless offloading to the
device tree for MT7988.

This allows using WED on devices with MT7988 SoC and MT7995E, MT7996E or
MT7992E wireless controllers.

Devices with 4 GiB of RAM (or more) will still need ajustments to avoid
running out of swiotlb entries.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-10-27 14:27:20 +00:00
Daniel Golle
b27075e12b mediatek: add wireless offloading firmware to MT7988 boards
Install mt7988-wo-firmware by default on boards based on MT7988.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-10-23 13:40:09 +01:00
Hauke Mehrtens
d0abb26f40 mediatek: Remove double CONFIG_HARDEN_BRANCH_PREDICTOR
CONFIG_HARDEN_BRANCH_PREDICTOR option is included two times in this
configuration file. Remove one definition. On arm32 SoC it should not be
needed.

Fixes: 54f9744c82 ("treewide: disable spectre mitigation on unaffected Arm32 targets")
Link: https://github.com/openwrt/openwrt/pull/16743
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-10-22 21:13:26 +02:00
Daniel Golle
e550c6d381 mediatek: fix OpenWrt One ubinized image in IB
The ImageBuilder when using the profile for the OpenWrt One has been
failing because the initramfs image included in the ubinized image could
not be found.

Fix that by using the staged initramfs instead when using the
ImageBuilder.

Fixes: 797904b3cb ("mediatek/filogic: add OpenWrt One support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-10-21 00:49:22 +01:00
Rosen Penev
a6252a6dfc mediatek: leds-smartrg: handle disabled LEDs
If LEDs are disabled, they should not be handled.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16651
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-10-19 19:19:38 +02:00
Rosen Penev
0dfe1e876a mediatek: leds-smartrg: use devm_mutex_init
No longer need normal _remove function. Replaced with _disable.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16651
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2024-10-19 19:19:38 +02:00
Daniel Golle
dbc2923cbe mediatek: filogic: convert Acer Predator W6 to use NVMEM framework
Read WiFi calibration data via NVMEM framework. The MAC addresses are
stored inside a file on a filesystem and hence still have to be
extracted in userspace.

WiFI EEPROM extraction has already accidentally been partially removed
by commit 3e6de5d77a ("mediatek: use NVMEM framework on all Adtran
devices").

Fixes: 3e6de5d77a ("mediatek: use NVMEM framework on all Adtran devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-10-18 12:38:21 +01:00
Daniel Golle
7e51d6a4c8 mediatek: mt7622: add netdev rename preinit script
Add preinit script to rename network interfaces according to the
label provided in Device Tree.

Fixes: b6d8297510 ("mediatek: mt7622: add Adtran SmartRG SDG-841t6 device")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-10-16 00:10:28 +01:00
Chukun Pan
e98987048a mediatek: filogic: reorder alphabetically
Reorder scripts to keep alphabetical order.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2024-10-15 21:36:16 +01:00
Chukun Pan
5fd4743d4c mediatek: filogic: fix network config for mt7986b-rfb
Fix the network configuration according to the device tree.

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
2024-10-15 21:36:16 +01:00
Daniel Golle
3e6de5d77a mediatek: use NVMEM framework on all Adtran devices
Use NVMEM framework to assign MAC addresses and WiFi EEPROM data on
all Adtran SmartRG devices.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-10-15 17:56:06 +01:00
Daniel Golle
b6d8297510 mediatek: mt7622: add Adtran SmartRG SDG-841t6 device
Specification
 SoC:   MediaTek MT7622A (2x Cortex-A53)
 RAM:   NANYA NT5CC256M16ER-EK (512 MiB)
 MMC:   Kioxia THGBMNG5D1LBAIT (4 GiB)
 ETH0:  Intel/MaxLinear GPY211 (2500M/1000M/100M/10M)
 ETH1:  Lantiq/Intel/MaxLinear PEF7071/GPY111 (1000M/100M/10M)
 WLAN0: MediaTek MT7915E + MT7975D 2T2R 802.11bgn/ax (2.4G)
                                   2T2R 802.11an/ac/ax (5G L)
 WLAN1: MediaTek MT7915E + MT7975A 4T4R 802.11an/ac/ax (5G H)
 BT:    BT5 provided by MT7915E+MT7975D (missing firmware)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-10-15 17:55:05 +01:00
Daniel Golle
175bd80349 mediatek: add driver for Adtran MFGINFO NVMEM layout
This driver allows retrieving MAC addresses and other factory information
via the NVMEM framework on Adtran devices.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2024-10-15 17:55:05 +01:00