The kernel logs the error "bcm6368_nand 10000200.nand: there is not valid
maps for state default" on boot and all nand pins show as UNCLAIMED in
sysfs pinmux-pins.
bcm6362.dtsi, bcm6368.dtsi and bcm63268.dtsi use the undocumented property
group which the driver doesn't understand. This has been documented upstream
in commit caf963efd4b0b9ff42ca12e52b8efe277264d35b.
Replacing group with pins allows the nand pins to be properly configured.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[add bcm636/bcm6368 and fix commit title]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit d1e9c50d06a8cb618cb85ab489cbcccaec220636)
The GS1900 images have been updated to have a larger firmware partition,
bumping the compatibility version to 2.0. However, since this version is
generated on first boot and the default was used, these images still
advertised 1.0 after a fresh install.
Add a new uci-defaults script that will generate the correct version for
all affected Zyxel GS1900 devices.
Fixes: 35acdbe9095d ("realtek: merge Zyxel GS1900 firmware partitions")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit a25809a474defedbd8f05d628d2c8525d79d549d)
set macaddress correctly for board
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17305
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 363f52d067e1852d46ccdc3ab4d12bc2f9d018dd)
The blocksize was too high, resulting in forgetting the config on sysupgrade
It is not needed for SPI-NOR.
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17305
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 24fc5ff2136a10bf0ee9e764ae0404b2928a67ce)
The dual-boot partition layout for the Zyxel GS1900 switches results in
6.9MB for both kernel and rootfs. Depending on the package selection,
this may already leave no space for the user overlay.
Merge the two firmware partitions, effectively dropping dual boot
support with OpenWrt. This results in a firmware partition of 13.9MB,
which should leave some room for the future.
To maintain install capabilites on new devices, an image is required
that still fits inside the original partition. The initramfs is used as
factory install image, so ensure this meets the old size constraints.
The factory image can be flashed via the same procedure as vendor images
when reverting to stock, can be installed from stock, or can be launched
via tftpboot.
Link: https://github.com/openwrt/openwrt/issues/16439
Link: https://github.com/openwrt/openwrt/pull/16442
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 35acdbe9095d81e896a2dfa65e7df871a023b996)
GPIO 5 on the RTL8231 is defined reset the system, but fails to actually
do so. This triggers a kernel a number of warnings and backtrace for
GPIO pins that can sleep, such as the RTL8231's. Two warnings are
emitted by libgpiod, and a third warning by gpio-restart itself after it
fails to restart the system:
[ 106.654008] ------------[ cut here ]------------
[ 106.659240] WARNING: CPU: 0 PID: 4279 at drivers/gpio/gpiolib.c:3098 gpiod_set_value+0x7c/0x108
[ Stack dump and call trace ]
[ 106.826218] ---[ end trace d1de50b401f5a153 ]---
[ 106.962992] ------------[ cut here ]------------
[ 106.968208] WARNING: CPU: 0 PID: 4279 at drivers/gpio/gpiolib.c:3098 gpiod_set_value+0x7c/0x108
[ Stack dump and call trace ]
[ 107.136718] ---[ end trace d1de50b401f5a154 ]---
[ 111.087092] ------------[ cut here ]------------
[ 111.092271] WARNING: CPU: 0 PID: 4279 at drivers/power/reset/gpio-restart.c:46 gpio_restart_notify+0xc0/0xdc
[ Stack dump and call trace ]
[ 111.256629] ---[ end trace d1de50b401f5a155 ]---
By removing gpio-restart from this device, we skip the restart-by-GPIO
attempt and rely only on the watchdog for restarts, which is already the
de facto behaviour.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 2ada95ccdf85f7ff82000dcf028659eb178ea50f)
The AR8035 PHY is used in most Octeon boards supported by OpenWRT (all
the Ubiquiti routers at least). To be able to use its PHY-specific
functionality (cable testing, LED Control, ...) it should be built on
Octeon. It also needs the regulator framework, so enable that as well.
These boards are not space-constrained, so this really has no downsides.
Tested on an EdgeRouter Lite, cable tests now work with ethtool-full.
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Link: https://github.com/openwrt/openwrt/pull/17318
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4892ea9a74da8cf934dc534665c3689d2139507b)
Include specific SUPPORTED_DEVICES values derived from the .dts file.
This makes the generated profiles.json consistent with the 'board_name' from
'ubus call system board'.
Specifically, this fixes a bug in the generated profiles.json that breaks the
ASU clients when selecting the proper image from a build.
See the 'supported_devices' fields here for the incorrect (or incomplete) list:
https://downloads.openwrt.org/releases/24.10.0-rc1/targets/d1/generic/profiles.json
Links: https://forum.openwrt.org/t/owut-openwrt-upgrade-tool/200035/287
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17155
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 33e23e8922ce7b7e488c85816c4b1084ae3710b0)
This backport patch inserted suspend/resume callbacks
for the wrong PHY driver.
The fixed patch is needed for Huawei AP5030DN
to initialize its second PHY.
Refresh all affected patch with make target/linux/refresh.
Fixes: 06cdc07f8cc7 ("ath79: add support for Huawei AP5030DN")
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/17312
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d7f638bc692a7a81cf13c8ca50c7dc4a73c0fed9)
Change partition table in dts file.
Change DEVICE_COMPAT_VERSION
Enable automatic build.
To take advantage of the bigger kernel partition,
the uboot environment has to be changed:
setenv nboot 'nand read 0x81000000 0x60000 0x500000; bootm 0x81000000'
setenv bootcmd 'run nboot'
saveenv
Of course you need a u-boot capable of handling this.
The u-boot discussed in this forum thread:
https://forum.openwrt.org/t/zyxel-p2812hnu-f1-u-boot/100281
should be able to handle kernels up to an uncompressed size of 16MiB.
Signed-off-by: Isaac de Wolff <idewolff@gmx.com>
Link: https://github.com/openwrt/openwrt/pull/17209
Link: https://github.com/openwrt/openwrt/pull/17300
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 0d21cc8a92ea3b2cc94efefd60eae968a4296543)
Images for xrx200 8M flash are either not building due to image
size (TD-W8970, TD-W8980) or building such that the available
free space in the overlayfs is too little to be useful.
To keep images for these devices buildable, move them into a
small flash variant of the xrx200 subtarget. As these devices
are NOR flash only, remove NAND and UBI references from the
kernel config to gain some additional image size reduction.
The apparent 8M flash devices Arcadyan VGV7510KW22-brn,
Arcadyan VGV7519-brn and Lantiq Easy80920-nor seem to exist in
order to create special "factory" installation images for these
devices (which actually have larger flash: 16MB for the
Arcardyan devices; 64MB for the Lantiq device). As a
considerable amount of surgery would appear to be required to
the uboot-lantiq package structure to separate the "factory"
from the "sysupgrade" device recipes for these devices they
remain in the xrx200 target - if factory images aren't now
created, 23.05.x factory images should suffice for initial
installation.
Tested on: Netgear DM200, TP-Link TD-W8980,
AVM Fritz7490 (xrx200 subtarget: image build only)
Fixes: https://github.com/openwrt/openwrt/issues/16761
Signed-off-by: Andrew MacIntyre <andymac@pcug.org.au>
Link: https://github.com/openwrt/openwrt/pull/17113
(cherry picked from commit e63326e26a82cb083eec602b3a2f71d4cd8e2ea4)
Link: https://github.com/openwrt/openwrt/pull/17303
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is using mac-base and so a 0 needs to be added.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17274
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 0634ebed9f74dca6d008b00f9fa00cc1220fa425)
The KuWFi N650 is a 5GHz outdoor wireless bridge based on QCA9563.
Specs
=====
CPU: QCA9563, 775MHz
RAM: 128MiB
Flash: 16MiB
Wireless: QCA9888 (5GHz only)
Ethernet: 2x GBit (via QCA8337), 48V passive PoE
Installation
============
From OEM firmware
-----------------
The OEM firmware has telnet enabled by default. If not, it can be enabled
from the firmware web interface. You need a TFTP server on your computer
and the OpenWrt factory image should be available as "n650factory.bin".
It is assumed that your computer has the IP 192.168.1.1 and the N650
192.168.1.20 (default IP address).
1. Connect via Telnet to the device and log in with the default credentials
"admin:admin"
2. Exploit the limited interface by typing "ps & /bin/sh"
3. Press <ENTER> to start the shell
4. Enter the following commands:
$ cd /tmp
$ tftp -r n650factory.bin -g 192.168.1.1
$ cat << EOF > /tmp/openwrt.sh
IMAGE_NAME="\$1"
if [ ! -e \${IMAGE_NAME} ]; then
echo "Image file not found: \${IMAGE_NAME}"
exit 1
fi
. /usr/sbin/common.sh
kill_remaining TERM
sleep 3
kill_remaining KILL
run_ramfs mtd write \${IMAGE_NAME} firmware
sleep 2
reboot -f
EOF
$ chmod +x /tmp/openwrt.sh
$ /tmp/openwrt.sh n650factory.bin
Once the device reboots, it should load OpenWrt.
From UART
---------
UART installation is possible since the serial header is already soldered
on. The pinout is GND - Tx - Rx - VCC from top to bottom (RJ45 ports are
at the bottom). Connect with 115200 8N1.
First, boot OpenWrt from TFTP. Enter the following commands in the U-Boot
shell, assuming your computer has the IP address 192.168.1.1 and a TFTP
server running where the initramfs image is provided as n650.bin:
setenv ipaddr 192.168.1.20
setenv serverip 192.168.1.1
tftpboot 0x84000000 n650.bin
bootm
Once booted, transfer -loader.bin and -sysupgrade.bin images to the device
at /tmp. Enter the following commands, replacing the filenames:
mtd write /tmp/loader.bin loader
sysupgrade /tmp/sysupgrade.bin
Reboot and OpenWrt should load from flash.
Back to Stock
-------------
Back to stock is only possible if you saved a partition backup before
installing OpenWrt. Assuming you have fullbackup.bin covering the whole
flash, you need to prepare the image as follows:
$ dd if=fullbackup.bin of=fwconcat0.bin bs=65536 skip=4 count=212
$ dd if=fullbackup.bin of=loader.bin bs=65536 skip=216 count=1
$ dd if=fullbackup.bin of=fwconcat1.bin bs=65536 skip=217 count=22
$ cat fwconcat0.bin fwconcat1.bin > firmware.bin
Transfer firmware.bin and loader.bin to the OpenWrt device. First, flash
loader.bin to mtd device loader, then force sysupgrade:
$ mtd write loader.bin loader
$ sysupgrade -F firmware.bin
The reason for the two-step process is the way the flash layout is designed
for OpenWrt in contrast to the OEM firmware partition.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Link: https://github.com/openwrt/openwrt/pull/17089
Link: https://github.com/openwrt/openwrt/pull/17247
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit dde510cf979e896a622b7ed738009910a27de94e)
The eeprom data offset on 2.4GHz wmac is wrong. It is obvious that
this is a copy & paste issue.
Suggested-by: @cgm999 on https://github.com/openwrt/openwrt/issues/13969
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17263
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5a24850de1418510c421d45eb2436bdcb2b243c6)
The device path to the devices changed. Migrate the wifi
configurations from the old path to the new one. This is needed to
migrate Wireless configurations from OpenWrt 23.05 to OpenWrt 24.10.
This script is based on these two files:
target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
Fixes: 0ef927472148 ("mediatek: filogic: move mt7981 on-SoC blocks to "soc" node in DT")
Fixes: https://github.com/openwrt/openwrt/issues/17174
Link: https://github.com/openwrt/openwrt/pull/17210
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f8b93e2d12ef01fc565178c71c39470da798155a)
The vendor U-Boot on the Cudy WR3000 assign random mac addresses on boot
and set the 'local-mac-address' property which prevents Openwrt from
assigning the correct address from evmem.
This patch removes the alias for ethernet0 so that U-Boot doesn't add
the property.
Related to: a55ab9e1343e ("mediatek: filogic: prevent faulty mac address assignment")
Fixes: https://github.com/openwrt/openwrt/issues/15587
Signed-off-by: Ondřej Niesner <ondra.niesner@seznam.cz>
Link: https://github.com/openwrt/openwrt/pull/17201
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a498a84393a80de9f828b8465906761896ca4940)
Add NETGEAR_BOARD_ID and NETGEAR_HW_ID to DEVICE_VARS as multiple devices
set them in their recipes, so without them being added to DEVICE_VARS then
simply the value from last recipe that gets evaluated is used and images
are generated with the wrong ID-s.
Link: https://github.com/openwrt/openwrt/pull/17203
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 1b6f7ec6794233fbf7c1cf17dcee34053c08fa9c)
This reverts commit 70e41d0205d95386881fa1cdf6ee00f6cca1b3f6.
"ethaddr" is stored into the "u-boot-env" (stock: "Config") partition
and it's quoted with double-quotations, but that format is not supported
by the current NVMEM u-boot-env driver (and mac_pton() function) and the
MAC address won't be parsed to byte array.
This causes random MAC addresses on the adapters, so revert the above
commit.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17116
(cherry picked from commit af611bce44d3dcffd47c47f46b95400445498be9)
Link: https://github.com/openwrt/openwrt/pull/17117
Signed-off-by: Robert Marko <robimarko@gmail.com>
DTS file for this device seems to be using CRLF line endings, so lets
convert them into Unix-style LF.
Fixes: faf4b3e0f7a5 ("mediatek: filogic: add support for Cudy WR3000S v1")
Link: https://github.com/openwrt/openwrt/pull/17096
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 30ae0b3f1e331646054d8110e931dfaa32f7b414)
Image build fails with PR #16861 merged while PR #16860 not merged.
Removing kmod-leds-ktd202x from filogic.mk will fix the build process.
Fixes: 2898d1d1269a ("mediatek: add support for Acer Predator W6d and Acer Vero W6m")
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/17087
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 1bdb6d84046ec1c47f28c57651358470ed212ec3)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
PSI provides a canonical way to see resource pressure increases as
they develop, with pressure metrics for three major resources:
memory, CPU, and IO. PSI stats are like barometers that provide
fair warning of impending resource shortages, enabling users to
take more proactive, granular, and nuanced steps when resources
start becoming scarce.
References:
* https://www.kernel.org/doc/html/latest/accounting/psi.html
* https://lwn.net/Articles/759781/
Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/glinet_gl-mt6000
Run-tested: x86/64/AMD Cezanne, flogic/glinet_gl-mt6000
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/13819
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit eed39d45c2ff901b5327c7ab63c9131166e3140e)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit adds OpenWrt U-Boot layout support for Routerich AX3000. The
aims:
1. Get open-source U-Boot;
2. Get maximum available free space in OpenWrt.
Install
-------
1. Copy OpenWrt ubootmod-bl31-uboot.fip, ubootmod-preloader.bin, to the
/tmp folder of the router using scp.
2. Make mtd partitions backups:
http://192.168.1.1/cgi-bin/luci/admin/system/flash -> Save mtdblock
contents
3. Install kmod-mtd-rw:
```
opkg update && opkg install kmod-mtd-rw
```
4. Write FIP and preloader:
```
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd erase BL2
mtd write /tmp/ubootmod-preloader.bin BL2
mtd unlock FIP
mtd erase FIP
mtd write /tmp/ubootmod-bl31-uboot.fip FIP
```
5. Copy OpenWrt ubootmod-initramfs-recovery.itb to the tftp server root
with IP 192.168.1.254.
6. Reboot router:
```
reboot
```
U-Boot will automatically download from the tftp server and boot OpenWrt
initramfs system.
7. Copy OpenWrt ubootmod-squashfs-sysupgrade.itb to the /tmp dir of the
router using scp.
8. Run sysupgrade:
```
sysupgrade -n /tmp/squashfs-sysupgrade.itb
```
Recovery
--------
1. Place OpenWrt initramfs-recovery.itb image (with original name) on the
tftp server (IP: 192.168.1.254).
2. Press "reset" button and power on the router. After ~10 sec release the
button.
3. Use OpenWrt initramfs system for recovery.
BL2 and FIP recovery
--------------------
Use mtk_uartboot and UART connection if BL2 or FIP in UBI is destroyed:
Link: https://github.com/981213/mtk_uartboot
Return to stock:
----------------
1. Copy partition backups (BL2.bin and FIP.bin) to the /tmp dir of the
router using scp.
2. Install kmod-mtd-rw:
```
opkg update && opkg install kmod-mtd-rw
```
3. Restore stock U-Boot and reboot:
```
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd erase BL2
mtd write /tmp/BL2.bin BL2
mtd unlock FIP
mtd erase FIP
mtd write /tmp/FIP.bin FIP
reboot
```
4. Open U-Boot web recovery, upload stock firmware image and start
upgrade.
Link: http://192.168.1.1
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16791
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d413163832df93c321eef3fce8c4f72c350d5308)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Code cleanup. Simplify and unify how kernel image is passed to
Build/dna-bootfs
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/16811
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit ec839c786ca56c6143257b89f146aeafbb6cfd3a)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The mt76x8 series SoCs use the MIPS generic systick timer. Sync the
upstream Ralink systick driver changes and disable it for mt76x8
target to reduce the kernel size.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16844
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 0c57510cedeff9caf795930ff86a436aa54bcc6d)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
These options are filtered out since some weeks, remove them also from
the new stm32 target.
Fixes: 851e7f77e424 ("stm32: add new stm32 target")
Link: https://github.com/openwrt/openwrt/pull/17058
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit ea2c860225b8bbda98ed0526dc670825866835b6)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Deactivate CONFIG_CONTEXT_TRACKING_USER_FORCE: Force user context
tracking: This is a testing feature which should not be activate in
production environments according to the Kconfig help. It adds an extra
overhead.
Deactivate CONFIG_RCU_NOCB_CPU_DEFAULT_ALL: Offload RCU callback
processing from all CPUs by default: This option should only be used in
aggressive HPC or real-time workloads which we do not have in OpenWrt.
For normal workloads it increases the number of context switches.
In the default Arch Linux kernel both options are not activated.
Fixes: 31111680f6fc ("x86: switch config to a tickless kernel")
Link: https://github.com/openwrt/openwrt/pull/17057
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit ed523454454965da07c9c7a009ae0a3995aa7c33)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
128MB SPI-NAND (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
UART: 115200 8N1 3.3V
MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set
Installation
------------
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device + press reset pin. Keep pressing reset pin to enter the U-Boot shell.
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.88. Rename the image to "cudy3000s.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000s.bin; bootm 0x46000000
5. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Signed-off-by: David Ignjic <ignjic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit faf4b3e0f7a583a8fa1a65b302ac74457e48575f)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit adds support for two variants of the already supported router
Acer Predator Connect W6: The Acer Predator Connect W6d (W6 without 6 GHz
wifi) and the Acer Connect Vero W6m (W6 without 2.5G eth1 port, usb3 port,
and the 6 on-board gpio RGB LEDs, and with a KTD2026 RGB LED controller
instead of the KTD2061 LED controller of the W6/W6d).
The device tree for the W6m refers to the KTD202x driver suggested in
PR #16860.
Patching target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
removes the code repetition in (old) lines 121 to 124 on the occasion.
This is the last of four commits into which the original commit was split
to make reviews easier and more targeted.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 2898d1d1269a841e5bb8673801bd2a04ad120031)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In order to prepare for OpenWrt support other Acer W6 devices and to get
a step further to full hardware support for Acer Predator Connect W6, this
commit
- adjusts the product name ("Acer Predator Connect W6")
- updates gpio LED labels to function/color scheme
- show router status by using first rgb led instead of it's red color only
(blue: booting/failsafe mode; red: sysupgrade; green: running – was: red)
- changes switch/eth1 led configuration to reflect RX/TX activity and speed
(green: full 1Gbps/2.5Gbps speed; amber: lower speed; blink: RX/TX)
- shortens dummy dm-mod.create string in bootargs
- enables W6's i2c interface
This is the third of four commits into which the original commit was split
to make reviews easier and more targeted.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d42075dcefa407a03a30663879688475bb912729)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In order to prepare OpenWrt support for other Acer W6 devices and to adapt
the procedure to read and set mac addresses which other devices of the same
target are using (instead of needing an additional script and creating an
additional structure in the file system), this commit
- reads device mac addresses from u-boot environment
- avoids the detour via the file system to set the mac addresses
- drops redundant file /lib/preinit/05_extract_factory_data.sh
The idea and the implementation were thankfully taken from PR #16410.
This is the second of four commits into which the original commit was split
to make reviews easier and more targeted.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e7aaba2587e57dbd157899f7a2215ec6b7af5f89)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In order to prepare OpenWrt support for other Acer W6 devices, this commit
moves all device tree components that are used by all Acer W6/W6e/W6d/W6m
routers from mt7986a-acer-predator-w6.dts to mt7986a-acer-w6-common.dtsi
(new file) and includes this dtsi file in mt7986a-acer-predator-w6.dts.
Minor changes had to be made to the device tree in order to improve clarity
and – notably – to reduce the number of dtc warnings:
- replace (obviously wrong) led@<N> gpio led entities by led-<N>
- remove unnecessary (default-state = "off") gpio led statements
- rename entity “memory” to “memory@0”
- add missing #address-cells and #address-size in /soc/mmc@11230000
- add missing #address-cells and #address-size in /soc/pcie@11280000
- introduce symbols “nvmem” and “swport0” in dtsi (referenced in dts)
The changes were checked with `diff -BEZbdtwy --suppress-common-lines ...`
(comparing two dts files created using old and new fdt-1 blobs again), see
https://github.com/openwrt/openwrt/pull/16861/#issuecomment-2455680020 .
This is the first of four commits into which the original commit was split
to make reviews easier and more targeted.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit ce3b36b3d5374709b9b091390cb9053657be17fa)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
TP-Link CPE710-v2 is an outdoor wireless CPE for 5 GHz with one Ethernet
port based on the AP152 reference board. Compared to the CPE710-v1, the
only change observed in hardware is that the mdio address of the ethernet
physical changed from 0x4 to 0x0.
Specifications:
- SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz
- RAM: 128MiB DDR2 @ 650MHz
- Flash: 16MiB SPI NOR Based on the GD25Q128
- Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless
data rate), based on the QCA9896
- Ethernet: one 1GbE port
- 23dBi high-gain directional 2×2 MIMO parabolic antenna
- Power, LAN, WLAN5G Blue LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for around
30-40 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Tim Noack <tim@noack.id>
Link: https://github.com/openwrt/openwrt/pull/16637
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5572e0196a93604716ec36ebb8db6737fc6677aa)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This is done in preparation of adding support for the CPE710-v2,
which uses a similiar device tree.
Signed-off-by: Tim Noack <tim@noack.id>
Link: https://github.com/openwrt/openwrt/pull/16637
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 832cc8ce04122ea726178687b5168187b2465f7f)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The Zbtlink ZBT-WE2426-B is an indoor dual band WiFi router
with 4 external non detachable antennas and 5 Fast Ethernet ports.
Hardware of ZBT-WE2426-B:
- SoC: MT7628AN
- RAM: 64 MB (Winbond W9751G6K8-25)
- Storage: 8 MB SPI flash (S25FL064K)
- Ethernet: 5x 10/100 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz: on SoC (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 8x
- Buttons: 1x reset
- USB: 1x 2.0
- MicroSD slot: 1x
- Power: 9 VDC, 1 A
- Uart: GND TX RX PWR - J1 on the PCB
- Board silkscreen: "ZBT-WE2426-C V04" "2018-02-28" "CTT" "13 18"
Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.
Installation:
- Using the bootloader web server. Hold the reset button while turning
the power on. Upload the sysupgrade image on http://192.168.1.1.
- Using the sysupgrade command in PandoraBox OpenWrt.
LEDs:
- LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
(GPIOs 43,42,41,40,39,44)
- WLAN5G uses pin of MT7612EN.
- The POWER LED is directly connected to the VCC. It can be reconnected to
the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.
Buttons:
- The RESET button is connected to the GPIO 38 of the MT7628AN SoC.
MAC addresses as verified by OEM firmware:
use address source
2g *:b0 factory 0x4 (label)
5g *:b1 factory 0x8004
LAN *:b2 factory 0x28
WAN *:b3 factory 0x2e
Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
Link: https://github.com/openwrt/openwrt/pull/16927
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3a9752ea027b8969750c0dd7f89b6afc357dcffa)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
New stm32 target introduces support for stm32mp1 based devices.
For now it includes an initial support of the STM32MP135F-DK device.
The specifications bellow only list supported features.
Specifications
--------------
SOC: STM32MP135FAF7
RAM: 512 MiB
Storage: SD Card
Ethernet: 2x 100 Mbps
Wireless: 2.4GHz Cypress CYW43455 (802.11b/g/n)
LEDs: Heartbeat (Blue)
Buttons: 1x Reset, 1x User (USER2)
USB: 4x 2.0 Type-A
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 851e7f77e424f24cda8531330f2d82ebc942c0a4)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
All new routers are shipped with ubi size 112MB since early September.
Bootloader update required (ask vendor , see wiki)
These partitions weren't used:
firmware_backup
zrsave
config2
Signed-off-by: Romanov Danila <pervokur@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16686
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d8a9669093359d60f4d6f183b58a22f24cf01731)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Commit e52c57bb1b30375e0bcc5523db76a672a4a8b4a4 renamed all
network ports to match the faceplate of the Gowin 1U Rack
Mount Server and added the br-lan bridge for the eth* ports.
This commit adds the PoE port to the br-lan bridge and a
br-wan bridge for the two SFP ports so that all ports are
part of the default network configuration.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/16965
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 75af6a0d736a696ca726cb44d813791858c29f0c)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
