Having initramfs image built with same config as on buildbots:
CONFIG_TARGET_MULTI_PROFILE=y
CONFIG_TARGET_ALL_PROFILES=y
CONFIG_TARGET_PER_DEVICE_ROOTFS=y
Its currently impossible to flash/recover the device using that image as
losetup is missing:
root@OpenWrt:/# sysupgrade -v /tmp/openwrt-ipq807x-generic-prpl_haze-squashfs-sysupgrade.bin
...
/lib/upgrade/do_stage2: line 38: losetup: not found
Failed to detach all loop devices. Skip this try.
So lets fix it by including the needed utils for sysupgrade in
DEFAULT_PACKAGES set.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 07fe8bc62a)
ipq807x does not compile-in hwmon core, and this is leading to the hwmon
code in AQR driver not being compiled due to IS_REACHABLE(CONFIG_HWMON)
evaluating to false as hwmon is being built as a module.
So, lets not compile-in Aquantia PHY driver so it can be included as kmod
instead to have functioning hwmon.
This allows using the thermal sensors in AQR-s as thermal zones for
cooling devices like fans.
Signed-off-by: Robert Marko <robimarko@gmail.com>
QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports.
Specifications:
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 1024MB of DDR3
• Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR
(contains art and u-boot-env)
• Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C)
• WLAN:
2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate
5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate
• LEDs:
7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs
• Buttons: 1x soft reset / 1x WPS
• Power: 12V DC jack
A poulated serial header is onboard.
RX/TX is working, bootwait is active, secure boot is not enabled.
SSH can be activated in the stock firmware, hold WPS button til the second beep
(yes the router has a buzzer)
SSH is available on port 22200, login with user admin and
password "mac address of the router".
Installation Instructions:
• obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial)
• stop auto boot
• setenv serverip 192.168.10.1
• setenv ipaddr 192.168.10.10
• tftpboot the initramfs image
(openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb)
• bootm
• make sure that current_entry is set to "0":
"fw_printenv -n current_entry" should be print "0". If not,
do "fw_setenv current_entry 0"
• copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
to the device to /tmp folder
• sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4)
• reboot
Note: this leaves the second kernel / rootfs parition untouched. So if you want
to go back to stock, stop u-boot autoboot, "setenv current_entry 1" ,
"saveenv", "bootipq".
Stock firmware should start from the second partition.
Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt
in the first partitions
Make 10G Aquantia phy's work:
The aquantia phy's need a firmware to work. This can either be loaded
in linux with a userspace tool or in u-boot.
I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is
aq_load_fw available in u-boot. But first the right firmware needs to write
to the 0:ETHPHYFW mtd partition (it is empty on my device)
Grab the ethphy firmware image from:
https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn
and scp that to openwrt.
Check the 0:ETHPHYFW partition number:
cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10.
Backup the 0:ETHPHYFW partition:
dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place.
Write the new firmware image to the 0:ETHPHYFW partition:
"mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10".
Reboot to u-boot.
Check if aq_load_fw is working:
"aq_load_fw 0", that checks the firmware and if successfull,
loads iram and dram to one of the aquantia phy's.
If that worked, add the aq_load_fw to the bootcmd:
setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq"
"saveenv"
"reset"
Board reboots and the firmware load to both phy's should start and
then openwrt boots.
Check if the 10G ports work.
Note: lan port labeled "10G-2" is configured as WAN port as per default.
All other port are in the br-lan. This can be changed in the network config.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Include NSS DP and SSDK (Pulled as dependency) by default on ipq807x to
provide wired networking to the target.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Qualcomm Atheros IPQ807x is a modern WiSoC featuring:
* Quad Core ARMv8 Cortex A-53
* @ 2.2 GHz (IPQ8072A/4A/6A/8A) Codename Hawkeye
* @ 1.4 GHz (IPQ8070A/1A) Codename Acorn
* Dual Band simultaneaous IEEE 802.11ax
* 5G: 8x8/80 or 4x4/160MHz (IPQ8074A/8A)
* 5G: 4x4/80 or 2x2/160MHz (IPQ8071A/2A/6A)
* 5G: 2x2/80MHz (IPQ8070A)
* 2G: 4x4/40MHz (IPQ8072A/4A/6A/8A)
* 2G: 2x2/40MHz (IPQ8070A/1A)
* 1x PSGMII via QCA8072/5 (Max 5x 1GbE ports)
* 2x SGMII/USXGMII (1/2.5/5/10 GbE) on Hawkeye
* 2x SGMII/USXGMII (1/2.5/5 GbE) on Acorn
* DDR3L/4 32/16 bit up to 2400MT/s
* SDIO 3.0/SD card 3.0/eMMC 5.1
* Dual USB 3.0
* One PCIe Gen2.1 and one PCIe Gen3.0 port (Single lane)
* Parallel NAND (ONFI)/LCD
* 6x QUP BLSP SPI/I2C/UART
* I2S, PCM, and TDMA
* HW PWM
* 1.8V configurable GPIO
* Companion PMP8074 PMIC via SPMI (GPIOS, RTC etc)
Note that only v2 SOC models aka the ones ending with A suffix are
supported, v1 models do not comply to the final 802.11ax and have
lower clocks, lack the Gen3 PCIe etc.
SoC itself has two UBI32 cores for the NSS offloading system, however
currently no offloading is supported.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The target is in an incomplete state and will not receive Kernel 5.10
support, ego it should be dropped before the next release.
People are working on ipq807x with Kernel 5.15 which is only relevant
for the second next release. Once a working patchset exists the target
can be added again.
Signed-off-by: Paul Spooren <mail@aparcar.org>
There is no such role as target maintainer anymore, one should always
send corresponding changes for the review and anyone from the commiters
is allowed to merge them or eventually use the hand break and NACK them.
Lets make it clear, that it is solely a community doing the maintenance
tasks.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
This is still missing a lot of love but people want to start working on it
so lets give them a common baseline.
Signed-off-by: John Crispin <john@phrozen.org>
