Commit Graph

20022 Commits

Author SHA1 Message Date
Koen Vandeputte
162e016fed ar71xx: expand kernel size for ubnt targets
Kernel 4.14 is pretty large causing a build error as the partition is too small.
Expand the kernel partition a bit to make it fit.

* ubnt-uap-pro
* ubnt-unifi-outdoor-plus

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-29 16:20:47 +01:00
Koen Vandeputte
d6b63f1698 ar71xx: disable ap91-5g due to kernel size
This target causes a build failure as the kernel image does not fit
into the kernel partition.

As the kernel is located behind the rootfs, it cannot be enlarged
as the boot entry location would get altered.

Disable this target for now.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-29 16:20:47 +01:00
Koen Vandeputte
7c78be1b74 ar71xx: switch more targets to dynamic partitioning
Targets:
- TP-LINK ER355
- TP-LINK C25 V1
- TP-LINK C59 V1
- TP-LINK C7 V4
- TP-LINK C7 V5

Fixes build issues seen due to the kernel being too big

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-29 11:21:23 +01:00
Radek Dostál
9d35b68776 ar71xx: switch TP-Link RE450 v1 to dynamic partitioning
As mentioned in commit 5f24933 recent changes on ar71xx (switch to 4.14,
memory compaction, ...) cause an increase in kernel size, making it too
big for RE450.

RE450 images were not build due to the following error message:
os-image partition too big (more than 1572864 bytes): Success

Tested on RE450, device boots and was used to send this patch.

Reported-by: Enrico Mioso <mrkiko.rs@gmail.com>
Suggested-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[rewrote commit msg keeping it tight + fixed SoB lines]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-29 11:21:23 +01:00
David Bauer
f89fc43a50 ar71xx: move OCEDO Koala to generic and use dynamic partitioning
This changes the OCEDO Koala flash-layout to a unified firmware
partition, thus making the ar71xx-generic kernel fit in flash.

Compile and runtested on OCEDO Koala.

Signed-off-by: David Bauer <mail@david-bauer.net>
[small title reword]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-29 11:21:23 +01:00
Mathias Kresin
374e646724 ath79: fix PQI Air Pen support
Use the correct dts filename. It has to be <soc>_<manufacturer>_<device>.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-10-28 11:03:49 +01:00
YuheiOKAWA
27eae6597e ath79: add support for PQI Air Pen
SoC: AR9330 (or AR9331 revision?)
Ethernet x1, Wireless 2.4G, uSD card slot x1.
USB Power, include Li-Po Battery.

Flash 8MiB. (factory is dual image)
1. write image is use half 4MiB size from factory.
  write initramfs image to mtd6 and mtd7.
2. change next boot setting. next is mtd6 boot.
  echo -ne "\x01" | dd of=/dev/mtdblock8 conv=notrunc bs=1 count=1 seek=0

3. rewrite sysupgrade image.
  change next boot setting. next is mtd4.
  echo -ne "\x00" | dd of=/dev/mtdblock8 conv=notrunc bs=1 count=1 seek=0

OEM mtd.
dev:    size   erasesize  name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00010000 00010000 "ART"
mtd3: 00010000 00010000 "NVRAM"
mtd4: 00140000 00010000 "uImage"
mtd5: 00280000 00010000 "rootfs"
mtd6: 00140000 00010000 "uImage2"
mtd7: 00280000 00010000 "rootfs2"
mtd8: 00010000 00010000 "CONF"

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
2018-10-28 10:59:14 +01:00
Roger Pueyo Centelles
23f9b2d9a9 ath79: Add support for Ubiquiti LiteAP ac (LAP-120)
This commit adds support for the Ubiquiti LiteAP ac (LAP-120), an outdoor
5 GHz AC access point with an integrated 120° 16 dBi antenna. The device
was previously known as LiteBeam AP ac but was later rebranded.

CPU:    Atheros AR9342 SoC
RAM:    64 MB DDR2
Flash:  16 MB NOR SPI
Ports:  1 GbE port (PoE in)
WLAN:   5 GHz QCA899X (PCI)

The integrated QCA899X is a Ubiquiti branded part with modified vendor
and product id (0777:11ac9). It is very similar to the NanoStation loco
AC, except for the 2.4 GHz management radio (missing here).

Installation procedure is the same as the NanoStation [loco] AC:

1. Connect to serial header on device
2. Power on device and enter uboot console
3. Set up tftp server serving an openwrt initramfs build
4. Load initramfs build using the command tftpboot in the uboot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs openwrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-10-28 10:59:09 +01:00
Koen Vandeputte
5f298b95a1 kernel: add missing symbol for target bcm53xx
Fixes: ca88f4153f ("kernel: bump 4.14 to 4.14.77")

Reported-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-23 10:57:02 +02:00
Rafał Miłecki
9b385b2496 bcm53xx: use upstream SPI controller fix
This just moves patch to use 0xx prefix and includes maintainer's s-o-b.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-10-23 09:43:08 +02:00
Koen Vandeputte
bc3d47cd12 kernel: bump 4.14 to 4.14.78
Refreshed all patches.

Remove upstreamed:
- 050-net-emac-fix-fixed-link-setup-for-the-RTL8363SB-swit.patch

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-22 15:28:31 +02:00
Koen Vandeputte
9c42391c0d kernel: bump 4.9 to 4.9.135
Refreshed all patches.

Fixes:
- CVE-2018-10883

Compile-tested on: ar71xx, layerscape
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-22 15:28:31 +02:00
Ryan Mounce
4d2613b01a mpc85xx: workaround 4.14 cross compile issue
Regression introduced with 4.10 by 43c9127d94d62a232ed33ed2eab8a08657ce5472

Build will fail if system 'ar' does not support deterministic builds.
e.g. macOS with Xcode toolchain

Appears to be fixed upstream in 4.18 by af3901cbbd3de182aafb8ee553c825c0074df6a2

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2018-10-20 16:24:29 +02:00
Christian Lamparter
fc70276e6c apm821xx: add disk-activity triggers via DT.
The WNDR4700 and the MBL have a dedicated HDD activity LED.
This patch adds the default led triggers to the DTS and
removes the entries in 01_leds.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-10-20 16:13:39 +02:00
Christian Lamparter
1d5d77612f apm821xx: apm82181.dtsi overhaul
- order entries by mmio address where possible

 - switch to lower-case address values

 - comment on BSP u-boot behaviour in regards to
   what it edits and look for

 - annotate irq lines with the help of interrupt-names

 - remove deprecated "device_type" properties
   The pci and network device_type had to stay since
   they are required by the drivers and u-boot.
   the cpu and memory device_types will remain as well
   as they are still part of the DT Spec.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-10-20 16:13:39 +02:00
Christian Lamparter
9ca82c2374 apm821xx: force WNDR4700 console to 115200n8
With the upcoming 4.19 release, the serial console on the
Netgear WNDR4700 would no longer work as it is never really
set and always relied on the kernel's serial code not to
change the baud rate.

On the stock firmware, Netgear forced the console setting
through a custom CONFIG_CMDLINE in their kernel to 115200.
Normally, they should have done it in a different way and
just passed the baudrate through a "console=..." kernel
parameter via the bootargs in the "/chosen" dt node.
But in their default u-boot bootcmd setting, they somehow
forgot to add the "run addtty", so there's no easy way to
pass the baudrate from u-boot to the kernel. So it has
to be forced as otherwise it ends up as 9600 baud.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-10-20 16:13:39 +02:00
Christian Lamparter
68bb91018d apm821xx: set uart compatible to ns16750
The APM821XX/PPC460EX datasheet mentions:
"Register compatibility with 16750 register set"

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-10-20 16:13:39 +02:00
Linus Walleij
f280bd7fa8 gemini: Fix up image generation
I noticed that the image generator for the Gemini generates
some 10+ MB files for the second (application) partition.
This is just wrong. The first 6144K partition named initramfs
easily fits OpenWRTs squashfs,jffs2 overlayed partitions
with nice headroom for storing configuration files.

Generate a blank partition for the hddapp.tgz file and delete
it after generating the firmware image - when performing
updates manually you just want the "rd.z" file around
anyways.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-10-20 16:13:39 +02:00
Linus Walleij
10ec966f7b gemini: Break out USB to packages
This creates a new kernel package for the fotg210 host
controller and uses that with the gemini to shrink the
kernel. The SQ201 needs the USB2 PCI package as well.

The build system required me to make kernel_oldconfig
beofore it would build without errors so some minor
unrelated Kconfig entries are changed.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-10-20 16:13:39 +02:00
Baptiste Jonglez
b2c68ceea7 kernel: Add support for Winbond w25q128jv SPI NOR flash
Newer batches of several Mikrotik boards contain this yet-unsupported
flash chip, for instance:

- rb941-2nd (hAP lite)
- rb952ui-5ac2nd (hAP ac lite)
- RBM33G

and probably other Mikrotik boards need this patch as well.

The patch was submitted upstream by Robert Marko: https://patchwork.ozlabs.org/patch/934181/

Closes: FS#1715
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Cc: Robert Marko <robimarko@gmail.com>
2018-10-20 16:13:39 +02:00
Koen Vandeputte
ca88f4153f kernel: bump 4.14 to 4.14.77
Refreshed all patches.

Altered patches:
- 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch

New symbol for arm targets:
- HARDEN_BRANCH_PREDICTOR

Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-19 10:01:57 +02:00
Koen Vandeputte
6d682d82b0 kernel: bump 4.9 to 4.9.134
Refreshed all patches.

Compile-tested on: ar71xx, layerscape
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-19 10:01:57 +02:00
Fabio Bettoni
ddc11c3932 ar71xx/ath79: fix mtd corruption
In commit fec8fe8069 ("kernel: bump 4.9 to 4.9.116") [1], the following patch for removed:
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch

This patch contained fixes for both write and erase functions.

While the chip-detects for erase got fixed upstream [2],
some modifications are still required, even with the fixes applied.

While at it, also apply the same fix for target ath79,
which suffers the same issue.

Not doing so results in following errors seen:

Collected errors:
 * pkg_write_filelist: Failed to open //usr/lib/opkg/info/luci-lib-ip.list: I/O error.
 * opkg_install_pkg: Failed to extract data files for luci-lib-ip. Package debris may remain!
 * opkg_install_cmd: Cannot install package luci-ssl.
 * opkg_conf_write_status_files: Can't open status file //usr/lib/opkg/status: I/O error.

[    0.780920] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    8.406396] jffs2: notice: (415) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    8.423476] mount_root: switching to jffs2 overlay
[  270.902671] jffs2: Write of 1989 bytes at 0x005ce6f8 failed. returned -5, retlen 962
[  270.931965] jffs2: Write of 1989 bytes at 0x005ceec0 failed. returned -5, retlen 0
[  270.939631] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[  270.950397] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[  270.957838] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[  270.968584] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[  270.976027] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero
[  270.986735] jffs2: Write of 68 bytes at 0x005ceec0 failed. returned -5, retlen 0
[  270.994225] jffs2: Not marking the space at 0x005ceec0 as dirty because the flash driver returned retlen zero

[1] https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=fec8fe806963c96a6506c2aebc3572d3a11f285f
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v4.9.133&id=a0239d83e1cb60de5e78452d4708c083b9e3dcbe

Fixes: fec8fe8069 ("kernel: bump 4.9 to 4.9.116")
Signed-off-by: Fabio Bettoni <fbettoni@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-17 18:55:37 +02:00
Koen Vandeputte
5f24933309 ar71xx: Move some targets to tiny
Recent changes on ar71xx (switch to 4.14, memory compaction, ...) cause
an increase in kernel size, making it too big for some devices.

Move these devices to the tiny target, where kernel symbols and
optimization for speed are disabled, reducing the kernel size.

Devices:
- EnGenius ENS202EXT
- OCEDO Koala

Compile-tested targets:

- ar71xx->generic->default
- ar71xx->smallFlash->Default

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-17 18:02:16 +02:00
Mathias Kresin
80c61c161a treewide: use wpad-basic for not small flash targets
Add out of the box support for 802.11r and 802.11w to all targets not
suffering from small flash.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Mathias did all the heavy lifting on this, but I'm the one who should
get shouted at for committing.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
2018-10-16 15:07:41 +01:00
Koen Vandeputte
0d0bd8e6da kernel: bump 4.14 to 4.14.76
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-16 10:08:56 +02:00
Koen Vandeputte
e80af4b53b kernel: bump 4.9 to 4.9.133
Refreshed all patches.

Compile-tested on: ar71xx, layerscape
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-16 10:08:54 +02:00
Koen Vandeputte
912340033a kernel: bump 3.18 to 3.18.124
Refreshed all patches.

Compile-tested: adm5120
Runtime-tested: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-16 10:06:45 +02:00
Felix Fietkau
d251a11f60 ramips: refresh mt7621 kernel config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-10-15 12:54:12 +02:00
Felix Fietkau
e34ea1b4ff kernel: add CONFIG_CC_OPTIMIZE_FOR_* to the default config
Avoid repeating them in the target config, they are overwritten by
top-level menuconfig anyway

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-10-15 12:54:00 +02:00
Rafał Miłecki
f00cb94f7c bcm53xx: add pending pinctrl driver
It's required to support devices using adjustable SoC pins for some
specific purpose (e.g. I2C, PWM, UART1).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-10-11 14:19:22 +02:00
Rafał Miłecki
92de28b751 bcm53xx: replace SPI revert with a fix sent upstream
Instead of reverting whole commit it's enough to just revert a single
line change. It seems the real problem with the regressing commit was a
bump of read chunk size. Switching back to 256 B chunks is enough to fix
the problem/regression.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-10-11 10:04:46 +02:00
Magnus Kroken
ba826ce4e7 mpc85xx: remove kernel 4.9 support
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
2018-10-11 08:04:10 +02:00
Magnus Kroken
650806d83a mpc85xx: switch to kernel 4.14
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
2018-10-11 08:04:02 +02:00
Magnus Kroken
c83c180489 mpc85xx: add kernel 4.14 support
Based on patches previously submitted by Achim Gottinger:
http://lists.infradead.org/pipermail/openwrt-devel/2018-June/012719.html

Tested on TP-Link TL-WDR4900 v1.

Signed-off-by: Magnus Kroken <mkroken@gmail.com>
2018-10-11 08:03:56 +02:00
Koen Vandeputte
13f283198e ar71xx: remove linux 4.9 support
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-10 15:12:01 +02:00
Koen Vandeputte
77d004de6d ar71xx: switch to kernel 4.14
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-10 14:45:11 +02:00
Koen Vandeputte
f983956a8b kernel: bump 4.14 to 4.14.75
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-10 14:45:11 +02:00
Koen Vandeputte
571fe28464 kernel: bump 4.9 to 4.9.132
Refreshed all patches.

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-10-10 14:45:11 +02:00
Felix Fietkau
212aa33226 kernel: enable memory compaction
Compaction is the only memory management component to form high order (larger
physically contiguous) memory blocks reliably. The page allocator relies on
compaction heavily and the lack of the feature can lead to unexpected OOM
killer invocations for high order memory requests. You shouldn't disable this
option unless there really is a strong reason for it.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Michal Hrusecky <michal.hrusecky@nic.cz>
2018-10-09 14:29:55 +02:00
Felix Fietkau
1e8882585c kernel: support gcc-optimized inlining on all architectures
Optimized inlining was disabled by default when gcc 4 was still
relatively new. By now, all gcc versions handle this well and there
seems to be no real reason to keep it x86-only.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-10-09 14:15:53 +02:00
Stijn Tintel
b134b3299c Revert "kernel: add a RPS balancer"
This reverts commit 7af1fb9faa.

With the RPS balancer patch, both my APU2s are crashing, sometimes just
after a few minutes of uptime.

[ 6241.170132] BUG: unable to handle kernel paging request at ffffffffa20a75a8
[ 6241.177248] IP: get_rps_cpu+0x41c/0x440
[ 6241.181140] PGD 2012067 P4D 2012067 PUD 2013063 PMD 0
[ 6241.186370] Oops: 0000 [#1] SMP NOPTI
[ 6241.190080] Modules linked in: pppoe ppp_async pptp pppox ppp_mppe ppp_generic nf_nat_pptp nf_flow_table_ipv6 nf_flow_table_ipv4 nf_flow_table_inet nf_conntrack_pptp lzo iptable_nat ipt_REJECT ipt_MASQUERADE ftdi_sio xt_time xt_tcpudp xt_tcpmss xt_string xt_statistic xt_state xt_recent xt_quota xt_policy xt_pkttype xt_owner xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_hl xt_helper xt_esp xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit xt_connbytes xt_comment xt_bpf xt_addrtype xt_TCPMSS xt_REDIRECT xt_NFQUEUE xt_LOG xt_HL xt_FLOWOFFLOAD xt_DSCP xt_CT xt_CLASSIFY wireguard usbserial ts_fsm ts_bm spidev slhc rfcomm nft_set_rbtree nft_set_hash nft_reject_ipv6 nft_reject_ipv4 nft_reject_inet nft_reject nft_redir_ipv4 nft_redir nft_quota nft_numgen nft_nat nft_meta nft_masq_ipv4 nft_masq
[ 6241.261735]  nft_log nft_limit nft_flow_offload nft_exthdr nft_ct nft_counter nft_chain_route_ipv6 nft_chain_route_ipv4 nft_chain_nat_ipv4 nfnetlink_queue nf_tables_ipv6 nf_tables_ipv4 nf_tables_inet nf_tables nf_reject_ipv4 nf_nat_tftp nf_nat_snmp_basic nf_nat_sip nf_nat_redirect nf_nat_proto_gre nf_nat_masquerade_ipv6 nf_nat_masquerade_ipv4 nf_nat_irc nf_conntrack_ipv6 nf_nat_ipv6 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat_h323 nf_nat_ftp nf_nat_amanda nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_tftp nf_conntrack_snmp nf_conntrack_sip nf_conntrack_rtcache nf_conntrack_proto_gre nf_conntrack_netlink nf_conntrack_irc nf_conntrack_h323 nf_conntrack_ftp nf_conntrack_broadcast ts_kmp nf_conntrack_amanda macvlan lzo_decompress lzo_compress libcrc32c kvm irqbypass
[ 6241.333427]  iptable_raw iptable_mangle iptable_filter ipt_ah ipt_ECN ip_tables hidp hci_uart crc_ccitt cdc_acm btusb btintel br_netfilter bnep bluetooth sch_cake tcp_bbr sch_teql em_nbyte sch_codel sch_prio sch_pie act_ipt em_meta sch_gred sch_dsmark cls_basic em_cmp em_text act_police sch_sfq sch_fq sch_multiq sch_red act_connmark nf_conntrack act_skbedit act_mirred em_u32 cls_u32 cls_tcindex cls_flow cls_route cls_fw sch_tbf sch_htb sch_hfsc sch_ingress configs evdev i2c_piix4 kfifo_buf industrialio i2c_dev xt_set ip_set_list_set ip_set_hash_netiface ip_set_hash_netport ip_set_hash_netnet ip_set_hash_net ip_set_hash_netportnet ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set
[ 6241.405252]  nfnetlink ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables x_tables ip_gre gre igb i2c_algo_bit ifb ip6_vti ip_vti sit l2tp_netlink l2tp_core ipcomp6 xfrm6_tunnel xfrm6_mode_tunnel xfrm6_mode_transport xfrm6_mode_beet esp6 ah6 ipcomp xfrm4_tunnel xfrm4_mode_tunnel xfrm4_mode_transport xfrm4_mode_beet esp4 ah4 ip6_tunnel tunnel6 tunnel4 ip_tunnel veth snd_compress snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd_rawmidi snd_seq_device snd_hwdep snd soundcore mpls_gso mpls_iptunnel mpls_router af_key xfrm_user xfrm_ipcomp xfrm_algo br2684 atm regmap_mmio vxlan udp_tunnel ip6_udp_tunnel ecdh_generic sha512_ssse3 sha512_generic sha256_ssse3 sha1_ssse3 seqiv jitterentropy_rng drbg md5 kpp ccp_crypto rsa_generic mpi asn1_decoder akcipher ccp sha256_generic
[ 6241.477726]  sha1_generic hmac ghash_generic gcm echainiv des_generic deflate zlib_deflate ctr cmac ccm cbc authenc crypto_acompress sdhci_pltfm pf_ring sp5100_tco leds_apu2 gpio_nct5104d button_hotplug ptp pps_core
[ 6241.497122] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 4.14.73 #0
[ 6241.503198] Hardware name: PC Engines apu2/apu2, BIOS v4.8.0.2 20180705
[ 6241.509858] task: ffff88012a0d8000 task.stack: ffffc90000070000
[ 6241.515841] RIP: 0010:get_rps_cpu+0x41c/0x440
[ 6241.520246] RSP: 0018:ffff88012ed83db0 EFLAGS: 00010286
[ 6241.525511] RAX: 00000000ffffffff RBX: 0000000000011ae8 RCX: 0000000000000001
[ 6241.532737] RDX: 00000000ffffffff RSI: ffff88012a0d8788 RDI: 0000000000000282
[ 6241.539956] RBP: ffff88012ed83e00 R08: 0000000000000001 R09: 0000000000000000
[ 6241.547183] R10: 0000000000000000 R11: 0000000000000000 R12: ffffffff82dae2e0
[ 6241.554403] R13: ffff880124de4480 R14: 0000000000000000 R15: ffff880128120000
[ 6241.561625] FS:  0000000000000000(0000) GS:ffff88012ed80000(0000) knlGS:0000000000000000
[ 6241.569820] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 6241.575651] CR2: ffffffffa20a75a8 CR3: 00000001251da000 CR4: 00000000000406e0
[ 6241.582830] Call Trace:
[ 6241.585322]  <IRQ>
[ 6241.587372]  ? lock_acquire+0x59/0x80
[ 6241.591102]  netif_receive_skb_internal+0x1e4/0x2d0
[ 6241.596037]  napi_gro_receive+0x48/0x90
[ 6241.599948]  igb_alloc_rx_buffers+0xc97/0x1b60 [igb]
[ 6241.604981]  ? note_gp_changes+0x76/0xc0
[ 6241.608963]  net_rx_action+0x10c/0x280
[ 6241.612752]  __do_softirq+0xf0/0x22d
[ 6241.616375]  irq_exit+0x5e/0xa0
[ 6241.619573]  do_IRQ+0xee/0x110
[ 6241.622682]  common_interrupt+0x8b/0x8b
[ 6241.626556]  </IRQ>
[ 6241.628699] RIP: 0010:native_safe_halt+0x6/0x10
[ 6241.633260] RSP: 0018:ffffc90000073e10 EFLAGS: 00000202 ORIG_RAX: ffffffffffffff3d
[ 6241.640910] RAX: ffff88012a0d8000 RBX: ffff88012a190c00 RCX: 0000000000000000
[ 6241.648110] RDX: ffff88012a0d8000 RSI: 0000000000000001 RDI: ffff88012a0d8000
[ 6241.655354] RBP: ffffc90000073e10 R08: 0000000000000006 R09: 0000000000000000
[ 6241.662554] R10: 0000000000000000 R11: 0000000000000000 R12: ffff88012a190c64
[ 6241.669791] R13: 0000000000000001 R14: 0000000000000001 R15: 0000000000000001
[ 6241.676986]  acpi_safe_halt.part.9+0xe/0x20
[ 6241.681226]  acpi_idle_do_entry+0x2c/0x40
[ 6241.685325]  acpi_idle_enter+0x1ee/0x2b0
[ 6241.689298]  ? sched_clock+0x9/0x10
[ 6241.692839]  cpuidle_enter_state+0x1f2/0x230
[ 6241.697162]  cpuidle_enter+0x12/0x20
[ 6241.700803]  call_cpuidle+0x38/0x40
[ 6241.704335]  do_idle+0xed/0x160
[ 6241.707557]  cpu_startup_entry+0x6e/0x70
[ 6241.711557]  start_secondary+0x1b4/0x1d0
[ 6241.715536]  secondary_startup_64+0xa5/0xb0
[ 6241.719777] Code: d4 48 8d 04 9b 48 8b 35 53 a7 ac 00 48 8d 1c 43 48 83 c6 64 48 c1 e3 03 48 8d bb e8 e2 da 82 e8 cb a9 ba ff 41 8b 14 1c 48 89 d0 <48> 0f a3 15 dc dc b6 00 0f 83 46 fc ff ff 48 83 c4 28 5b 41 5c
[ 6241.739100] RIP: get_rps_cpu+0x41c/0x440 RSP: ffff88012ed83db0
[ 6241.744993] CR2: ffffffffa20a75a8
[ 6241.748373] ---[ end trace 77367d9f9830d5bc ]---

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-10-08 11:03:23 +03:00
Julian Haupt
0308385d1d sunxi: add support for Orange Pi Zero
Signed-off-by: Julian Haupt <julian.haupt@hauptmedia.de>
2018-10-07 22:16:10 +02:00
David Bauer
35c314bdb2 ath79: add Fritz!Box 4020 switchconfig
In contrast to ar71xx, uci switchconfig is missing in the ath79 target.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-10-07 17:26:30 +02:00
David Bauer
5815bb2e41 ath79: add support for TP-Link TL-WA901ND v2
This commit adds support for the TP-Link TL-WR901ND v2 access point.

CPU:   Atheros AR9132 400MHz
RAM:   32MB
FLASH: 4MiB
WiFi:  Atheros AR9103 3x3:2 bgn
LED:   Power (static on)
       LAN (controlled by PHY)
       SYS, WiFi, QSS toggleable
BTN:   Reset, QSS

Installation:
Upload the factory image via the vendor-GUI.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-10-07 15:49:25 +02:00
INAGAKI Hiroshi
6d1abbcab4 ath79: add support for Buffalo WZR-HP-G302H A1A0
Buffalo WZR-HP-G302H is a 2T2R 2.4 GHz 11n router, based on Atheros
AR7242.

It is Japanese market model of WZR-HP-G300NH2, but there are some
diffrences. This commit is based on WZR-HP-G300NH2 in ar71xx.
And, G302H has several hardware versions and hardware is different
dependent on the versions. This commit adds support for "A1A0"
version.

Specification:

- Atheros AR7242
- 64 MB of RAM (DDR2)
- 32 MB of Flash
  - 2x 16 MB SPI-NOR flash
- 2.4 GHz 2T2R wifi
  - Atheros AR9283
- 5x 10/100/1000 Mbps Ethernet
  - Atheros AR8316
- 7x LEDs, 5x keys
  - LED: 1x gpio-leds, 6x ath9k-leds
  - key: 3x buttons, 2x slide switches
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Boot WZR-HP-G302H normaly and connect the computer to its LAN port
2. Access to "http://192.168.11.1/" and move to firmware update page
("ファーム更新")
3. Select the OpenWrt factory image and click update ("更新実行")
button to perform firmware update
4. Wait ~200 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-10-07 15:44:19 +02:00
INAGAKI Hiroshi
d745eac636 ath79: add hwver parameter to buffalo-tag
In order to be able to set the value of "hardware version" other than
"3", I added the "hwver" parameter.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-10-07 15:44:19 +02:00
Robert Marko
adbd9d1f1f ath79: Add support for TP-Link TL-WR842N-v2
This PR adds support for TP-Link TL-WR842N-v2 router which is supported by ar71xx to ath79.

This is a low cost model with following specs:

CPU: Atheros AR9341 SoC
RAM: 32 MB DDR1
Flash: 8 MB NOR SPI
Switch: Internal AR9341 5 port 10/100 Mbit
Ports:  5x 10/100 Mbit(1x WAN, 4x LAN)
USB: 1x USB2.0
WLAN: 2.4 GHZ AR9341

Installation:

Simply flash the factory image through stock firmware WEB UI.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-10-07 15:44:19 +02:00
Sven Eckelmann
ebd57de1f9 ipq40xx: Create /var/lock directory in platform_do_upgrade_*
The sysupgrade_pre_upgrade hook was removed with 5e1b4c57de ("base-files:
drop fwtool_pre_upgrade") while there were still scripts using it:

* target/linux/ar71xx/base-files/lib/upgrade/allnet.sh
* target/linux/ar71xx/base-files/lib/upgrade/openmesh.sh
* target/linux/ipq40xx/base-files/lib/upgrade/openmesh.sh

Not running the hooks can either prevent a successful upgrade or brick the
device because the fw_setenv program cannot be started correctly.

Instead of adding this hook again, the directory /var/lock for fw_setenv
can also just be created directly before fw_setenv is called.

Fixes: 5e1b4c57de ("base-files: drop fwtool_pre_upgrade")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-10-07 15:44:19 +02:00
Sven Eckelmann
c383e0c979 ar71xx: Create /var/lock directory in platform_do_upgrade_*
The sysupgrade_pre_upgrade hook was removed with 5e1b4c57de ("base-files:
drop fwtool_pre_upgrade") while there were still scripts using it:

* target/linux/ar71xx/base-files/lib/upgrade/allnet.sh
* target/linux/ar71xx/base-files/lib/upgrade/openmesh.sh
* target/linux/ipq40xx/base-files/lib/upgrade/openmesh.sh

Not running the hooks can either prevent a successful upgrade or brick the
device because the fw_setenv program cannot be started correctly.

Instead of adding this hook again, the directory /var/lock for fw_setenv
can also just be created directly before fw_setenv is called.

Fixes: 5e1b4c57de ("base-files: drop fwtool_pre_upgrade")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
2018-10-07 15:44:19 +02:00