Commit Graph

31 Commits

Author SHA1 Message Date
Sieng-Piaw Liew
6bc26c7d49 bmips: bcm6328: add Innacomm W3400V6
Innacomm W3400V6 is an xDSL B/G wireless router based on Broadcom
BCM6328 SoC.

SoC: Broadcom BCM6328
CPU: BMIPS4350 V8.0, 320 MHz, 1 core
Flash: SPI-NOR 8MB, MX25L6406E
RAM: 64 MB
Ethernet: 4x 10/100 Mbps
Switch: Integrated
Wireless: 802.11b/g, BCM4312
LEDs/Buttons: 9x / 2x

Flash instruction, web UI:
1. Set a static IP on your computer compatible with 192.168.1.1, i.e
192.168.1.100.
2. Connect the ethernet cable from your computer to the router.
3. Make sure the router is powered off.
4. Press the reset button, don't release it yet!
5. While pressing reset, power on the router.
6. Wait 10 seconds or more.
Note: The power LED is red at first then turns to solid green when
ready.
7. Release the reset button.
8. Browse to 192.168.1.1
9. Select .bin file.
10. Upgrade the image.
11. Wait for it to reboot.

Signed-off-by: Sieng-Piaw Liew <liew.s.piaw@gmail.com>
[Fix cfe nvmem-layout and pinctrl_leds indentation]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2024-01-16 10:49:27 +01:00
Daniel González Cabanelas
df8e4b6c2e bmips: add support for Arcadyan AR7516
The Arcadyan AR7516, AKA Orange Bright Box or EE Bright Box 1, is a wifi
fast ethernet router, 2.4 GHz single band with two internal antennas. It
comes with a horizontal stand black shiny casing.

Newer Bright Box 1 model stands vertically, and comes with a totally
different board inside, not compatible with this firmware.

Hardware:
 - SoC: Broadcom BCM6328
 - CPU: single core BMIPS4350 V7.5 @ 320Mhz
 - RAM: 64 MB DDR2
 - Flash: 8 MB SPI NOR
 - Ethernet LAN: 4x 100Mbit
 - Wifi 2.4 GHz: Broadcom BCM43227 802.11bgn (onboard)
 - USB: 1x 2.0
 - ADSL: yes, unsupported
 - Buttons: 2x
 - LEDs: 9x, power LED is hardware controlled
 - UART: yes

Installation in two steps, new CFE bootloader and firmware:

Install new CFE:
  1. Power off the router and press the RESET button
  2. Power on the router and wait some seconds
  3. Release the RESET button
  3. Browse to http://192.168.1.1, this web interface will offer both
     firmware (“Software”) upgrade and bootloader upgrade; be sure to
     use the bootloader section of the upload form.
  4. Upload the new CFE (availabe at the wiki page)
  5. Wait about a minute for flashing to finish and reboot into the new bootloader.

Install OpenWrt via new CFE web UI:
  1. After installing the new CFE, visit http://192.168.1.1
  2. Upload the Openwrt cfe firmware
  5. Wait a few minutes for it to finish

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-06-22 17:53:32 +02:00
Daniel González Cabanelas
6cb3328b4f bmips: add support for NuCom R5010UNv2
The NuCom R5010UNv2 is a wifi fast ethernet router, 2.4 GHz single band
with two external antennas.

Hardware:
 - SoC: Broadcom BCM6328
 - CPU: single core BMIPS4350 V7.5 @ 320Mhz
 - RAM: 64 MB DDR2
 - Flash: 16 MB SPI NOR
 - Ethernet LAN: 4x 100Mbit
 - Wifi 2.4 GHz: Broadcom BCM43217 802.11bgn (onboard)
 - USB: 1x 2.0
 - Buttons: 2x
 - ADSL: yes, unsupported
 - LEDs: 7x
 - UART: yes

Installation via CFE web UI:
  1. Power off the router and press the RESET button
  2. Power on the router and wait 12 or more seconds
  3. Release the RESET button
  4. Browse to http://192.168.1.1 and upload the Openwrt cfe firmware
  5. Wait a few minutes for it to finish

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-06-19 20:39:52 +02:00
Álvaro Fernández Rojas
47cc09aa7a bmips: add support for Comtrend VG-8050
The Comtrend VG-8050 is a wifi gigabit ethernet router, 2.4 GHz single band with
two external antennas.

Hardware:
 - SoC: Broadcom BCM63169
 - CPU: dual core BMIPS4350 @ 400Mhz
 - RAM: 128 MB DDR
 - Flash: 128 MB NAND
 - LAN switch: Broadcom BCM53125, 5x 1Gbit
 - Wifi 2.4 GHz: SoC (BCM63268) 802.11bgn
 - USB: 1x 2.0 (optional)
 - Buttons: 2x (reset)
 - LEDs: yes
 - UART: yes

Installation via CFE web UI:
  1. Power off the router.
  2. Press reset button near the power switch.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Browse to http://192.168.1.1 and upload the firmware.
  5. Wait a few minutes for it to finish.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-16 09:48:53 +02:00
Álvaro Fernández Rojas
38ebb2eafd bmips: add support for Sercomm AD1018
The Sercomm AD1018 is a wifi fast ethernet router, 2.4 GHz single band with
two internal antennas.

Hardware:
 - SoC: Broadcom BCM6328
 - CPU: single core BMIPS4350 @ 320Mhz
 - RAM: 64 MB (v1) / 128 MB (v2) DDR
 - Flash: 128 MB NAND
 - Ethernet LAN: 4x 100Mbit
 - Wifi 2.4 GHz: miniPCI Broadcom BCM43217 802.11bgn
 - USB: 1x 2.0
 - Buttons: 3x (reset)
 - LEDs: yes
 - UART: yes

Installation via OEM web UI:
  1. Use the admin credentials to login via web UI
  2. Go to Managament->Update firmware and select the OpenWrt CFE firmware
  3. Press "Update Firmware" button and wait some minutes until it finish

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-15 20:47:40 +02:00
Álvaro Fernández Rojas
434434ca47 bmips: bump LOADER_ENTRY to RAM + 16M
This is needed on devices like Sercomm AD1018 for booting recent kernels due
to bigger kernels.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-15 20:47:40 +02:00
Daniel González Cabanelas
e1a55de7a7 bmips: add support for Actiontec R1000H
The  Actiontec R1000H is a gigabit wifi router, 2.4 GHz single band with
two external antennas. It comes with a coaxial HomePNA port.

Hardware:
 - SoC: Broadcom BCM6368
 - CPU: dual core BMIPS4350 V3.1 @400Mhz
 - RAM: 64 MB DDR
 - Flash: 32 MB parallel NOR
 - LAN switch: Broadcom BCM53115, 5x 1Gbit
 - LAN coaxial : 1x HPNA 3.1, CG3211 + CG3213
 - Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn
 - USB: 1x 2.0
 - Buttons: 2x, 1 reset
 - LEDs: 7x
 - UART: yes

The HPNA hardware probably needs a firmware to make the coaxial port work.
In the OEM firmware, it's apparently sent with an utility (inhpna) through
the ethernet port.

Installation via CFE web UI:
  1. Connect the UART serial port.
  2. Power on the router and press enter at the console prompt to stop the
     bootloader.
  4. Browse to http://192.168.1.1 and upload the OpenWrt CFE firmware
  5. Wait a few minutes for it to finish

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-06-15 17:58:58 +02:00
Álvaro Fernández Rojas
bcdf861519 bmips: add support for Comtrend AR-5381u
The Comtrend AR-5381u is a wifi fast ethernet router, 2.4 GHz single band with
two internal antennas.

Hardware:
 - SoC: Broadcom BCM6328
 - CPU: single core BMIPS4350 @ 320Mhz
 - RAM: 64 MB DDR
 - Flash: 16 MB SPI NOR
 - Ethernet LAN: 4x 100Mbit
 - Wifi 2.4 GHz: miniPCI Broadcom BCM43225 802.11bgn
 - USB: 1x 2.0
 - Buttons: 1x (reset)
 - LEDs: yes
 - UART: yes

Installation via CFE web UI:
  1. Power off the router.
  2. Press reset button near the power switch.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Browse to http://192.168.1.1 and upload the firmware.
  5. Wait a few minutes for it to finish.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-12 18:53:00 +02:00
Álvaro Fernández Rojas
c3b1ef2dfd bmips: add support for Comtrend WAP-5813n
The Comtrend WAP-5813n is a wifi gigabit router, 2.4 GHz single band with
two external antennas.

Hardware:
 - SoC: Broadcom BCM6369
 - CPU: dual core BMIPS4350 @ 400Mhz
 - RAM: 64 MB DDR
 - Flash: 8 MB parallel NOR
 - LAN switch: Broadcom BCM53115, 5x 1Gbit
 - Wifi 2.4 GHz: miniPCI Broadcom BCM4322 802.11bgn
 - USB: 1x 2.0 (optional)
 - Buttons: 3x (reset)
 - LEDs: yes
 - UART: yes

Installation via CFE web UI:
  1. Power off the router.
  2. Press reset button near the power switch.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Browse to http://192.168.1.1 and upload the firmware.
  5. Wait a few minutes for it to finish.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-11 18:31:23 +02:00
Álvaro Fernández Rojas
3baa45fbd8 bmips: add support for Comtrend VR-3025un
The Comtrend VR-3025un is a wifi gigabit router, 2.4 GHz single band with
two external antennas.

Hardware:
 - SoC: Broadcom BCM6368
 - CPU: dual core BMIPS4350 @ 400Mhz
 - RAM: 64 MB DDR
 - Flash: 8 MB parallel NOR
 - Ethernet LAN: 4x 100Mbit
 - Wifi 2.4 GHz: miniPCI Broadcom BCM43222 802.11bgn
 - USB: 1x 2.0
 - Buttons: 1x (reset)
 - LEDs: yes
 - UART: yes

Installation via CFE web UI:
  1. Power off the router.
  2. Press reset button near the antenna.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Browse to http://192.168.1.1 and upload the firmware.
  5. Wait a few minutes for it to finish.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-11 12:09:40 +02:00
Álvaro Fernández Rojas
79844637df bmips: dgnd3700v1/dgnd3800b: add missing kmod-leds-gpio
Commit ed79519b8d missed adding kmod-leds-gpio to these devices.

Fixes: ed79519b8d ("bmips: add support for Netgear DGND3700 v1, DGND3800B")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-11 10:25:03 +02:00
Álvaro Fernández Rojas
389f7802db bmips: image: rename Device/bcm63xx_netgear
Every other Device definition in the target is using hyphens instead of
underscores.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-11 10:17:50 +02:00
Daniel González Cabanelas
71a6f45fdf bmips: add support for Netgear EVG2000
The Netgear EVG2000 is a wifi gigabit router, 2.4 GHz single band with
two internal antennas integrated in the main PCB.

Hardware:
 - SoC: Broadcom BCM6369
 - CPU: dual core BMIPS4350 V3.1 @400Mhz
 - RAM: 64 MB DDR
 - Flash: 16 MB parallel NOR
 - LAN switch: Broadcom BCM53115, 5x 1Gbit
 - Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn
 - USB: 2x 2.0
 - Buttons: 2x, 1 reset
 - LEDs: 10x
 - FXS: 2x
 - UART: yes

Installation via CFE web UI:
  1. Power off the router and make a temporal TX-RX shortcircuit on the
     serial pins.
  2. Power on the router and wait 3 or more seconds
  3. Remove the TX-RX shortcircuit
  4. Browse to http://192.168.1.1 or http://192.168.0.1 and upload the
     firmware
  5. Wait a few minutes for it to finish

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-06-11 09:54:52 +02:00
Daniel González Cabanelas
ed79519b8d bmips: add support for Netgear DGND3700 v1, DGND3800B
The Netgear DGND3700 v1 and DGND3800B are the same device but with
different factory firmwares. It's an xDSL wifi router with a slim black
shiny casing and 4 PCB internal antennas connected via UFL to a miniPCI
detachable card.

Hardware:
 - SoC: Broadcom BCM6368
 - CPU: dual core BMIPS4350 V3.1 @400Mhz
 - RAM: 128 MB DDR
 - NOR Flash: 32 MB parallel (CFE and OS)
 - NAND flash: 128 MB (empty)
 - Ethernet LAN: 5x 1Gbit
 - Wifi 2.4 GHz: Broadcom BCM43222 802.11bgn
 - Wifi 5 GHz: Broadcom BCM43222 802.11abgn
 - USB: 2x 2.0
 - Buttons: 3x, 1 reset
 - LEDs: 11x
 - UART: yes

Installation via OEM web UI:
  1. Open the Netgear administration web interface, by default:
        http://192.168.0.1
	user: admin
        password: password
  2. Look for "upgrade firmware" and proceed
  3. Wait some minutes until it finishes

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-06-10 15:37:52 +02:00
Álvaro Fernández Rojas
47ca33a0be bmips: bump LZMA Loader address
This allows booting bigger ramdisk images via TFTP at the cost of breaking 32M
RAM compatibility, but those devices have been unable to boot ramdisks on this
target for some time anyway due to not having enough RAM.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-09 19:48:42 +02:00
Daniel González Cabanelas
e7a0b61397 bmips: add support for Observa VH4032N
The Observa VH4032N is an xDSL wifi router with a vertical white casing
and two internal antennas connected via UFL.

Hardware:
 - SoC: Broadcom BCM6368
 - CPU: dual core BMIPS4350 V3.1 @400MHz
 - RAM: 128 MB DDR
 - Flash: 32 MB parallel NOR
 - Ethernet LAN: 4x 100Mbit
 - Wifi 2.4/5 GHz: onboard Broadcom BCM43222 802.11abgn
 - USB: 3x 2.0
 - Buttons: 2x, 1 reset
 - LEDs: 8x, blue and red
 - UART: 1x

Installation via OEM web UI:
  1. Use the admin credentials to login via web UI
  2. Go to Managament->Update firmware and select the OpenWrt CFE firmware
  3. Press "Update Firmware" button and wait some minutes until it finish

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-06-09 19:44:28 +02:00
Álvaro Fernández Rojas
3132eff000 bmips: shg2500: add BCM4360 fallback SPROM
Apart from the embedded BCM63268 wireless, this device has an external BCM4360
connected by PCIe which needs a fallback SPROM.
b43 isn't enabled for this device because BCM4360 isn't supported (AC PHY).

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-23 12:19:02 +02:00
Álvaro Fernández Rojas
0cecebd413 bmips: dgnd3700v2: add b43 wireless driver
Apart from the embedded BCM6362 wireless, Netgear DGND3700v2 has external
BCM43228 wireless connected by PCIe.
Fallback SPROM isn't needed for this one because it has a physical SPROM.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-23 12:19:02 +02:00
Álvaro Fernández Rojas
7122609082 bmips: switch to generic bcma/ssb fallback SPROM
Stop using bmips b43-sprom fixups and switch to generic bcma/ssb fallback
SPROMs. This way we don't need to include the b43-sprom fixups on devices
without Broadcom wireless.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-23 12:18:35 +02:00
Álvaro Fernández Rojas
db4f158c03 bmips: hg556a: switch to kmod-owl-loader
Stop using custom ath9k fixup and switch to standard kmod-owl-loader

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-18 19:45:04 +02:00
Álvaro Fernández Rojas
6fd8e0f943 bmips: add subtargets for each SoC
BMIPS is a generic arch that can be used for multiple Broadcom SoCs, each one
with its own specific drivers, so instead of having a huge kernel supporting
all of them, let's switch to a subtarget per SoC like other OpenWrt targets.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-10 10:04:08 +02:00
Álvaro Fernández Rojas
8bee6a9f1d bmips: switch to LED kernel modules
Disable LED controllers from kernel config and switch to per device kernel
modules.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-09 10:52:32 +02:00
Álvaro Fernández Rojas
aefeb34223 bmips: add support for Sercomm SHG2500
Sercomm SHG2500 is a BCM63168 with 128M of RAM, 256M of NAND, an external
BCM53124S switch for the LAN ports and internal/external Broadcom wifi.
LEDs are connected to an external MSP430G2513 MCU controlled via SPI.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-09 10:33:13 +02:00
Álvaro Fernández Rojas
d11a7c4d95 bmips: use sercomm-pid script
Make use of sercomm-pid script for generating the Sercomm PID, which avoids
having to add an array of hex bytes for every new Sercomm device.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-09 10:21:58 +02:00
Álvaro Fernández Rojas
d309160d30 bmips: image: rename SERCOMM_VERSION to SERCOMM_FSVER
SERCOMM_VERSION is ambiguous and it should be more clear that it refers to the
version used for the filesystem.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-09 10:06:26 +02:00
Álvaro Fernández Rojas
6df12200d9 bmips: add support for Sercomm H-500s
Sercomm H-500s is a BCM63268 with 128M, internal and external (Quantenna) wifi
and external BCM53134S switch.
This device is already supported in bcm63xx target, so more information can be
found in https://openwrt.org/toh/sercomm/h500-s.

It's a perfect example of a device with internal and external switch
coexistance since most devices only have ports on one of the switches but not
both of them.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-03-22 20:57:07 +01:00
Álvaro Fernández Rojas
80a3ecc894 bmips: add Huawei HG253s v2 support
Huawei HG253s v2 is a BCM6362 with 128M RAM, internal wifi and external
BCM53124S switch.
This device is already supported in bcm63xx target, so more information can be
found in https://openwrt.org/toh/huawei/hg253s_v2.

It's a perfect example of a device with internal and external switch
coexistance since most devices only have ports on one of the switches but not
both of them.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-03-21 20:49:18 +01:00
Álvaro Fernández Rojas
12a3c863d2 bmips: loader-lzma: drop unused RAMSIZE parameter
This parameter has never been used.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-03-02 20:37:56 +01:00
Rosen Penev
2630e5063d treewide: replace wpad-basic-wolfssl default
The newly merged mbedtls backend is smaller and has fewer ABI related
issues than the wolfSSL one.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2023-02-04 02:35:03 +01:00
Álvaro Fernández Rojas
07c49462ad bmips: add wifi packages for supported devices
Netgear DGND3700v2 / Comtrend VR-3032u internal wireless not supported.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-03-23 20:23:47 +01:00
Álvaro Fernández Rojas
029093a302 bmips: add new target
This target has full device tree support, thus reducing the number of
patches needed for bcm63xx, in which there's a patch for every board.

The intention is to start with a minimal amount of downstream patches and
start upstreaming all of them.

Current status:
 - Enabling EHCI/OHCI on BCM6358 causes a kernel panic.
 - BCM63268 lacks Timer Clocks/Reset support.
 - No PCI/PCIe drivers.
 - No ethernet drivers.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-22 18:29:44 +01:00