The WatchGuard Firebox M200 and M300 use a Marvell 88e1543 PHY for the
first 3 ethernet ports. This PHY is supported by the Marvell Alaska PHY
driver, so enable it.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
There are various reports on Github and in the forum that this commit
causes multiple problems.
This reverts commit ee6ba216d8.
Fixes: #9420
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
octeon/patches-5.10 -> octeon/patches-5.15
Removed 140-octeon_e300_support.patch as E300 support appears to be upstreamed.
Reworked 130-add_itus_support.patch to compensate for the upstreaming of E300
octeon/config-5.15
The following Kernel Symbols were ADDED:
Line 5: +CONFIG_AF_UNIX_OOB=y
Line 6: +CONFIG_AHCI_OCTEON=y
Line 9: +CONFIG_ARCH_KEEP_MEMBLOCK=y
Line 16: +CONFIG_ATA=y
Line 17: +CONFIG_BINARY_PRINTF=y
Line 29: +CONFIG_CPU_R4K_FPU=y
Line 45: +CONFIG_FWNODE_MDIO=y
Line 51: +CONFIG_GENERIC_FIND_FIRST_BIT=y
Line 59: +CONFIG_GLOB=y
Line 61: +CONFIG_GPIO_CDEV=y
Line 77: +CONFIG_LTO_NONE=y
Line 85: +CONFIG_MIPS_FP_SUPPORT=y
Line 93: +CONFIG_NET_SELFTESTS=y
Line 94: +CONFIG_NET_SOCK_MSG=y
Line 105: +CONFIG_PATA_OCTEON_CF=y
Line 106: +CONFIG_PATA_TIMINGS=y
Line 114: +CONFIG_PTP_1588_CLOCK_OPTIONAL=y
Line 121: +CONFIG_SATA_AHCI_PLATFORM=y
Line 122: +CONFIG_SATA_HOST=y
Line 124: +CONFIG_SCSI_COMMON=y
Line 132: +CONFIG_SOCK_RX_QUEUE_MAPPING=y
Line 157: +CONFIG_USB_XHCI_HCD=y
Line 158: +CONFIG_USB_XHCI_PLATFORM=y
The following kernel symbols were REMOVED:
Line 21: -CONFIG_BLK_SCSI_REQUEST=y
Line 37: -CONFIG_ENABLE_MUST_CHECK=y
Line 69: -CONFIG_HOLES_IN_ZONE=y
Line 102: -CONFIG_OF_NET=y
Line 140: -CONFIG_SYS_SUPPORTS_HUGETLBFS=y
Compiled for Itus Shield, Boots successfully, continuing to test
for existing 5.10 memory leak.
Signed-off-by: Donald Hoskins <grommish@gmail.com>
[refresh patches]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The memory leak is fixed by the kernel patches backported in the
previous commit.
This reverts commit 1fa8780056.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Use the kernel's built-in formula for computing this value.
The value applied by OpenWRT's sysctl configuration file does not scale
with the available memory, under-using hardware capabilities.
Also, that formula also influences net.netfilter.nf_conntrack_buckets,
which should improve conntrack performance in average (fewer connections
per hashtable bucket).
Backport upstream commit for its effect on the number of connections per
hashtable bucket.
Apply a hack patch to set the RAM size divisor to a more reasonable value (2048,
down from 16384) for our use case, a typical router handling several thousands
of connections.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
There is a hard to reproduce, even harder to track down memory leak in
Octeon since kernel 5.10. Mark octeon source-only until it is plugged.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This reverts commit 35d2bbc29b as we
believe we found that it is indeed an openssl issue, where openssl is
trying to use getrandom(2), but fails because this particular builder
has an ancient kernel without that syscall. We didn't get to the bottom
of why openssl doesn't fall back to something like /dev/random.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
When upgrading a TP-Link Archer C5 v1 from ar71xx to ath79,
the 5ghz radio stops working because the device path changed.
Same has been done for the Archer C7 before:
commit e19506f206 ("ath79: migrate Archer C7 5GHz radio device paths")
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
Config option `ARM_ARCH_TIMER` has been removed during rebasing onto
5.15 kernel in commit 2b395c2982 ("imx: update config for 5.15").
Anyway, as stated in commit 8cdc356f8c ("mediatek: mt7623: Re-enable
ARM arch timer") config option `ARM_ARCH_TIMER` cannot be enabled in the
config directly; it is only selected by `HAVE_ARM_ARCH_TIMER`. We need
to enable the latter in our config.
Fixes: 2b395c2982 ("imx: update config for 5.15")
Reported-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In imx target we're sharing single, version agnostic kernel
`config-default` file, which doesn't work very well with current 5.10
and upcoming 5.15 kernel symbols as recent rebase onto 5.15 kernel
introduced in commit 2b395c2982 ("imx: update config for 5.15) has
introduced following regression with 5.10 kernel:
Marvell 88E6xxx Ethernet switch fabric support (NET_DSA_MV88E6XXX) [Y/n/m/?] y
Switch Global 2 Registers support (NET_DSA_MV88E6XXX_GLOBAL2) [Y/n/?] (NEW)
That NET_DSA_MV88E6XXX_GLOBAL2 kernel config symbol has been removed in
upstream commit 63368a7416df ("net: dsa: mv88e6xxx: Make global2 support
mandatory") in kernel version 5.12.
This issue could be probably fixed by introduction of separate kernel
config files for each currently used kernel versions and subtarget, but
it is not worth the hassle and resources as imx target is running mostly
upstream kernel, so lets fix it by switching to 5.15 version instead.
Fixes: 2b395c2982 ("imx: update config for 5.15")
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The label has the MAC address of eth0, not the WLAN PHY address. We can
merge the definition back into ar7241_ubnt_unifi.dtsi, as both DTS
derived from it use the same interface for their label MAC addresses
after all.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Add Kernel 5.15 patches + config. This is currently only available for
the generic subtarget, as it was exclusively tested with this target.
Tested-on: Siemens WS-AP3610, Enterasys WS-AP3705i
Signed-off-by: David Bauer <mail@david-bauer.net>
Specify the switch ports in the DTS file.
Re-enable it after it was disabled by commit e9672b1a8f ("bcm53xx: switch to the
upstream DSA-based b53 driver").
Signed-off-by: SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com>
[rmilecki: reword commit & drop unneeded whitespace change]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
platform_nand_pre_upgrade() is gone since commit 790692dde2
("base-files: drop support for the platform_nand_pre_upgrade()").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Asus RT-AC88U is an AC3100 router featuring 9 Ethernet ports over the
integrated Broadcom and the external Realtek switch.
Hardware info:
* Processor: Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz
* Switch: BCM53012 in BCM4709C0KFEBG & external RTL8365MB
* DDR3 RAM: 512 MB
* Flash: 128 MB (ESMT F59L1G81LA-25T)
* 2.4GHz: BCM4366 4×4 2.4/5G single chip 802.11ac SoC
* 5GHz: BCM4366 4×4 2.4/5G single chip 802.11ac SoC
* Ports: 8 Ports, 1 WAN Ports
Flashing instructions:
* Boot to CFE Recovery Mode by holding the reset button while power-on.
* Connect to the router with an ethernet cable.
* Set IPv4 address of the computer to 192.168.1.2 subnet 255.255.255.0.
* Head to http://192.168.1.1.
* Reset NVRAM.
* Upload the OpenWrt image.
CFE bootloader may reject flashing the image due to image integrity check.
In that case, follow the instructions below.
* Rename the OpenWrt image as firmware.trx.
* Run a TFTP server and make it serve the firmware.trx file.
* Run the URL below on a browser or curl.
http://192.168.1.1/do.htm?cmd=flash+-noheader+192.168.1.2:firmware.trx+flash0.trx
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
[rmilecki: mark BROKEN until we sort out nvram & CFE recovery]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The tc package does not exits any more, it was split into tc-tiny,
tc-full and tc-bpf. Include tc-bpf by default into realtek images.
This increases the compressed image size by about 232KBytes.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The realtek target is not a router, but basic device, see DEVICE_TYPE.
The basic device type does not come with firewall by default, see
include/target.mk for details. The realtek target extended
DEFAULT_PACKAGES manually with firewall.
This changes the defaults to take firewall4 and nftables instead of
firewall and iptables. This also adds the additional package
kmod-nft-offload.
The only difference to the router type is the missing ppp,
ppp-mod-pppoe, dnsmasq and odhcpd-ipv6only package.
This increases the compressed image size by about 422KBytes.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Do not include the dnsmasq and odhcpd-ipv6only package by default any
more. These services are not needed on a switch. If someone needs this
it is still possible to use opkg or image builder to add them.
This decreases the compressed image size by about 165KBytes.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
So the upcoming changes needed for 5.15 can be reviewed easily.
Removed following upstreamed patches:
* 062-add-sun8i-h3-zeropi-support.patch
* 100-sunxi-h3-add-support-for-nanopi-r1.patch
* 101-sunxi-h5-add-support-for-nanopi-r1s-h5.patch
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixes following build issues:
Package kmod-r8169 is missing dependencies for the following libraries:
mdio_devres.ko
Package kmod-ixgbe is missing dependencies for the following libraries:
mdio_devres.ko
Package kmod-amd-xgbe is missing dependencies for the following libraries:
mdio_devres.ko
Signed-off-by: Petr Štetiar <ynezz@true.cz>
So the upcoming changes needed for 5.15 can be reviewed easily.
Removing following patches backported from 5.15:
* 101-v5.15-mfd-lpc_ich-Enable-GPIO-driver-for-DH89xxCC.patch
* 102-v5.15-platform-x86-add-meraki-mx100-platform-driver.patch
Removed upstreamed patch `300-pcengines_apu1_led.patch` in commit
1b40faf7e4ab ("leds: apu: extend support for PC Engines APU1 with newer
firmware")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Backports following fix:
hv: utils: add PTP_1588_CLOCK to Kconfig to fix build
The hyperv utilities use PTP clock interfaces and should depend a
a kconfig symbol such that they will be built as a loadable module or
builtin so that linker errors do not happen.
Prevents these build errors:
ld: drivers/hv/hv_util.o: in function `hv_timesync_deinit':
hv_util.c:(.text+0x37d): undefined reference to `ptp_clock_unregister'
ld: drivers/hv/hv_util.o: in function `hv_timesync_init':
hv_util.c:(.text+0x738): undefined reference to `ptp_clock_register'
References: https://lore.kernel.org/stable/20220328093115.7486-1-ynezz@true.cz/T/#u
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Using set_disk_ro() doesn't have the desired effect and instead of
just setting the single partition to be read-only it affects the
whole disk. Use the bd_read_only flag in struct block_device instead
to mark a partition being read-only.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Backport patch
8b6836d82470 ("net: dsa: mv88e6xxx: keep the pvid at 0 when VLAN-unaware")
from 5.15.
Keeping the pvid at 0 when VLAN-unaware makes it possible to drop the
hack introduced in commit 920eaab1d8 ("kernel: DSA roaming fix for
Marvell mv88e6xxx"). Dropping the hack makes it possible to use VLAN
interfaces with VID 1 on DSA ports without problems with FDB.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fix dedicated cpufreq for kernel 5.15 as they changed module
order and now it can happen that cpufreq probe after cache driver.
Also add lock between cache scaling in set_target as it's now required
by opp functions.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Now that smem actually free the leaked parts, when
a rootfs partition is detected, the kernel panics as
it try to free the static space allocated for the "ubi"
name. Change the logic and fix the name at the allocate_partition
function to correctly free the space allocated by smem.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Refresh patch for 5.15
Rework tweak patch to sync with upstream ipq8064 dtsi and fix
regression introduced.
Rename nand_controller to nand in every dts.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
the buildbots are having troubles with the image.
They seem to get "Killed" at the last step of the KERNEL rule:
|/cros-vbutil -k zImage.itb.vboot -c "root=PARTUUID=%U/PARTNROFF=1" -o zImage.itb.vboot.new
|make[4]: *** [Makefile:18: zImage.itb.vboot] Killed
Since the Google Wifi (Gale) is currently the only target in
this sub-target. So this means that subtarget has to be disabled
from the time being to not be picked up by the builders.
For people wanting to checkout out OpenWrt on the Google Wifi:
please compile it locally.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The inclusion of the kmod-leds-uleds into the userspace
nu801 package causes a circular dependency inside the
buildsystem... which causes it to be picked regardless
of other DEPENDS values.
In case of the mx100, this could be solved by moving the
kmod-leds-uled dependency to the kmod-meraki-mx100.
Bonus: drop @!LINUX_5_4 from kmod-meraki-mx100
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
There are 2 warning for ar8xxx swconfig.
- Fix not used dev variable when ETHERNET_PACKET_MANGLE
is not selected
- Convert fallthrough comment to compilation macro
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Backport qca8k mdio improvement patch merged upstream,
where we use eth packet when available to send mdio commands.
This should improve speed and cause less load on the CPU.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Prepare uImage.FIT partition parser for Linux 5.15
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Patches that add the additional AQR PHY ID-s is just copy/paste from 5.10
and kernel 5.11 dropped the ack_interrupt method for PHY IRQ handling,
instead handle_interrupt is used.
So, simply switch to using handle_interrupt like other upstream AQR PHY-s.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
After fixing the original 720 patch, it looks like more were added for
additional AQR ID-s.
Patches that add the additional AQR PHY ID-s is just copy/paste from 5.10
and kernel 5.11 dropped the ack_interrupt method for PHY IRQ handling,
instead handle_interrupt is used.
So, simply switch to using handle_interrupt like other upstream AQR PHY-s.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Standardize pending patch tcp_no_window_check patch as with
new kernel they added a check for global variables.
The 2 new condition are that they must be read-only or
the data pointer should not point to kernel/module global
data.
Remove the global variable and move it to a standard place
following other variables logic.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Rework hack patch in dir for kernel 5.15.
For the specific patch of packet mangeling introduce a new extra_priv_flags
as we don't have enough space to add additional flags in priv_flags.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Refresh qca8k backport patches for 5.15 kernel.
Vlan_prepare is now dropped and there were some changes
to vlan add/remove functions.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
In commit ab143647ef ("kernel: generic: improve FIT partition parser")
part_bits was bumped to 2 in order to allow up to 3 additional FIT
sub-images mapped into sub-partitions.
This change has to be reflected also in our local patch
420-mtd-set-rootfs-to-be-root-dev.patch
which still assumed part_bits==1 for mtdblock devices in case of
CONFIG_FIT_PARTITION=y.
Fixes: #9557
Fixes: ab143647ef ("kernel: generic: improve FIT partition parser")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This commit builds on previous efforts to add support
for Sophos devices.
* Add support for Sophos XG 85 with/without wireless
* Add support for Sophos XG 86 with/without wireless
Tested on Sophos XG 85w rev1 and XG 86 rev 1
Signed-off-by: Raylynn Knight <rayknight@me.com>
# CONFIG_PSTORE_COMPRESS_DEFAULT="deflate"
this can lead to confusion. Thankfully, in the KConfig
world this setting is still interpreted as disabled.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
For HiWiFi series devices, label_mac can be read from bdinfo partition,
and lan_mac, wlan2g_mac are same as the label_mac. Converting label_mac
to wlan5g_mac only needs to unset 6th bit. (It seems that all HiWiFi's
label_mac start with D4:EE)
For example:
label D4:EE:07:32:84:88
lan D4:EE:07:32:84:88
wan D4:EE:07:32:84:89
wlan2g D4:EE:07:32:84:88
wlan5g D0:EE:07:32:84:88
Tested on HiWiFi HC5661.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
at91/sama7 fails to build due to:
| Asymmetric (public-key cryptographic) key type (ASYMMETRIC_KEY_TYPE) [Y/?] y
| Asymmetric public-key crypto algorithm subtype (ASYMMETRIC_PUBLIC_KEY_SUBTYPE) [Y/?] y
| Asymmetric TPM backed private key subtype (ASYMMETRIC_TPM_KEY_SUBTYPE) [N/m/?] (NEW)
|Error in reading or end of file.
please note that asym_tpm (module) has been removed in 5.17:
<https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=d3cff4a9>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
removes usb-port remains as neither the WAC510 nor the WAC505
come with a USB port. Update the LED properties to phase out
labels and introduce generic node-names as well as adding
the color, function and function-enumerator properties.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ARM Builds like sunxi/cortexa53 or the rpi family failed
to build due to a new symbols showing up:
|Google Firmware Drivers (GOOGLE_FIRMWARE) [Y/n/?] y
| Coreboot Table Access (GOOGLE_COREBOOT_TABLE) [M/n/y/?] m
| Coreboot Framebuffer (GOOGLE_FRAMEBUFFER_COREBOOT) [N/m/?] (NEW)
|Error in reading or end of file.
Fixes: e5b009e532 ("kernel: Package GOOGLE_FIRMWARE drivers")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The OCEDO Raccoon had significant packet-loss with cables longer than 50
meter. Disabling EEE restores normal operation.
Also change the ethernet config to reduce loss on sub-1G links.
Signed-off-by: David Bauer <mail@david-bauer.net>
Avoid flooding the log with the message below by increasing the log
level to debug:
mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The patch was rejected by upstream. The mtk_nand driver should be
modified to support the mt7621 flash controller instead. As there is no
newer version to backport, or no upstream version to fix bugs, let's
move the driver to the files dir under the ramips target. This makes it
easier to make changes to the driver while waiting for mt7621 support to
land in mtk_nand.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Modified the radio frequency hardware part of e2600ac c1/c2,
need to cooperate with the modified board.bin file, the device
can work normally.
Signed-off-by: 张 鹏 <sd20@qxwlan.com>
This commit replaces patch number 0703 with the upstream accepted
version. This patch requires backporting an additional patch to
avoid conflicts.
The only significant change is the lower maximum MTU. Packets with
lengths over 2400 may be dropped.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit moves the patches for the r8152.c driver to the generic
directory. Previously they were only available on the bcm27xx target.
With these patches the Realtek RTL8153C, RTL8153D, RTL8156A and RTL8156B
chips are supported on all targets by the kmod-usb-net-rtl8152 module.
The RTL8156A and RTL8156B are the 2.5Gb/s Ethernet adapters.
The patches have been tested on TP-Link UE300 (RTL8153A) and UNITEK
1313B (RTL8156B).
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This reverts commit 80b7a8a7f5.
Now that 5.10 is the default kernel for all platforms, we can
bring back the NU801 userspace driver for platforms that rely
on it. Currently it's used on the MX100 x86_64 target, but
other Meraki platforms use this controller.
Note that we also now change how we load nu801. The way we did
this previously with procd worked, but it meant it didn't load
until everything was up and working.
To fix this, let's call nu801 from boot and re-trigger the
preinit blink sequence. Since nu801 runs as a daemon this is
now something we can do.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
(removed empty line, currently only MX100 uses it so: @TARGET_x86)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This model, also know as "1&1 HomeServer", shares the same features as 7530.
The vendor firmware has artificial software limitations: only 2 of the 4
LAN-Ports are GBit, and the USB-Host is only v2.0.
With OpenWrt, USB is already working at v3.0.
Signed-off-by: Andre Heider <a.heider@gmail.com>
(updated commit message to reflect current state)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Google WiFi (codename: Gale) is an IPQ4019-based AP, with 2 Ethernet
ports, 2x2 2.4+5GHz WiFi, 512 MB RAM, 4 GB eMMC, and a USB type C port.
In its stock configuration, it runs a Chromium OS-based system, but you
wouldn't know it, since you can only manage it via a "cloud" +
mobile-app system.
The "v2" label is coded into the bootloader, which prefers the
"google,gale-v2" compatible string. I believe "v1" must have been
pre-release hardware.
Note: this is *not* the Google Nest WiFi, released in 2019.
I include "factory.bin" support, where we generate a GPT-based disk
image with 2 partitions -- a kernel partition (using the custom "Chrome
OS kernel" GUID type) and a root filesystem partition. See below for
flashing instructions.
Sysupgrade is supported via recent emmc_do_upgrade() helper.
This is a subtarget because it enables different features
(FEATURES=boot-part rootfs-part) whose configurations don't make sense
in the "generic" target, and because it builds in a few USB drivers,
which are necessary for installation (installation is performed by
booting from USB storage, and so these drivers cannot be built as
modules, since we need to load modules from USB storage).
Flashing instructions
=====================
Documented here:
https://openwrt.org/inbox/toh/google/google_wifi
Note this requires booting from USB storage.
Features
========
I've tested:
* Ethernet, both WAN and LAN ports
* eMMC
* USB-C (hub, power-delivery, peripherals)
* LED0 (R/G/B)
* WiFi (limited testing)
* SPI flash
* Serial console: once in developer mode, console can be accessed via
the USB-C port with SuzyQable, or other similar "Closed Case
Debugging" tools:
https://chromium.googlesource.com/chromiumos/third_party/hdctools/+/master/docs/ccd.md#suzyq-suzyqable
* Sysupgrade
Not tested:
* TPM
Known not working:
* Reboot: this requires some additional TrustZone / SCM
configuration to disable Qualcomm's SDI. I have a proposal upstream,
and based on IRC chats, this might be acceptable with additional DT
logic:
[RFC PATCH] firmware: qcom_scm: disable SDI at boot
https://lore.kernel.org/linux-arm-msm/20200721080054.2803881-1-computersforpeace@gmail.com/
* SMP: enabling secondary CPUs doesn't currently work using the stock
bootloader, as the qcom_scm driver assumes newer features than this
TrustZone firmware has. I posted notes here:
[RFC] qcom_scm: IPQ4019 firmware does not support atomic API?
https://lore.kernel.org/linux-arm-msm/20200913201608.GA3162100@bDebian/
* There's a single external button, and a few useful internal GPIO
switches. I haven't hooked them up.
The first two are fixed with subsequent commits.
Additional notes
================
Much of the DTS is pulled from the Chrome OS kernel 3.18 branch, which
the manufacturer image uses.
Note: the manufacturer bootloader knows how to patch in calibration data
via the wifi{0,1} aliases in the DTB, so while these properties aren't
present in the DTS, they are available at runtime:
# ls -l
/sys/firmware/devicetree/base/soc/wifi@a*/qcom,ath10k-pre-calibration-data
-r--r--r-- 1 root root 12064 Jul 15 19:11 /sys/firmware/devicetree/base/soc/wifi@a000000/qcom,ath10k-pre-calibration-data
-r--r--r-- 1 root root 12064 Jul 15 19:11 /sys/firmware/devicetree/base/soc/wifi@a800000/qcom,ath10k-pre-calibration-data
Ethernet MAC addresses are similarly patched in via the ethernet{0,1} aliases.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
(updated 901 - x1pro moved in the process)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
See my upstream questions:
https://lore.kernel.org/linux-arm-msm/20200913201608.GA3162100@bDebian/
This effectively reverts upstream Linux commit 13e77747800e ("firmware:
qcom: scm: Use atomic SCM for cold boot"), because Google WiFi boot
firmwares don't support the atomic variant.
This fixes SMP support for Google WiFi.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
See firmware-utils.git commits [1], which implemented the cros-vbutil
verified-boot payload-packing tool, and extended ptgen for the CrOS
kernel partition type. With these, it's now possible to package kernel +
rootfs to make disk images that can boot a Chrome OS-based system (e.g.,
Chromebooks, or even a few AP models).
Regarding PARTUUID= changes: Chromium bootloaders work well with a
partition number offset (i.e., relative to the kernel partition), so
we'll be using a slightly different root UUID line.
NB: I've made this support specific to ip40xx for now, because I only
plan to support an IPQ4019-based AP that uses a Chromium-based
bootloader, but this image format can be used for essentially any
Chromebook, as well as the Google OnHub, a prior Chromium-based AP using
an IPQ8064 chipset.
[1]
ptgen: add Chromium OS kernel partition support
https://git.openwrt.org/?p=project/firmware-utils.git;a=commit;h=6c95945b5de973026dc6f52eb088d0943efa96bb
cros-vbutil: add Chrome OS vboot kernel-signing utility
https://git.openwrt.org/?p=project/firmware-utils.git;a=commit;h=8e7274e02fdc6f2cb61b415d6e5b2e1c7e977aa1
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tel(co Electronics) X1 Pro is preventing ipq40xx generic
from building due to the KERNEL_SIZE.
Whenever bigger kernels are possible, if lzma is supported
is unknown.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Required to allow sysupgrades from OpenWrt 19.07.
Closes#7071
Fixes: 98fbf2edc0 ("ath79: move TPLINK_HWID/_HWREV to parent for tplink-safeloader")
Tested-by: J. Burfeind <git@aiyionpri.me>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
It is disabled in the generic kernel config and not used in any of the
other targets. There was no specific reason for enabling it, so let's be
consistent and remove it from the qoriq kernel config.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
As the LED controller is working now, we can make good use of the LEDs
now.
- Drop the model-name prefix
- Rename eth0 / eth1 LEDs to LAN1 / LAN2, as they are labeled as such
on the casing
- Enable wired LEDs in userspace
Signed-off-by: David Bauer <mail@david-bauer.net>
Move the GPIO extender to the SoC node. Otherwise, the legacy PowerPC
init code will not populate the BUS and thus never probe spi-gpio.
Signed-off-by: David Bauer <mail@david-bauer.net>
While it hasn't always been clear whether the "AP" is part of the model
name on the Ubiquiti website, we include it for all other pre-AC
variants (AP Pro and the AP Outdoor+). Add it to the original UniFi AP
as well for consistency.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* only map filesystems configured in 'loadables'
* allow mapping more than one filesystem (e.g. customization/branding
or localization in addition to rootfs)
* small cleaning here and there
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If the selected boot configuration is stored by U-Boot in '/chosen'
node as 'bootconf' attribute, use that configuration to resolve the
block device used as rootfs. Fall back to use the default configuration
in case 'bootconf' is not present.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
a20-olinuxino-lime2 is currently having hard time with link detection of
certain 1000Mbit partners due to usage of generic PHY driver, probably
due to following missing workaround introduced in upstream in commit
3aed3e2a143c ("net: phy: micrel: add Asym Pause workaround"):
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability. This patch implements the workaround by defining a KSZ9031
specific get_feature callback to force the Asymmetric Pause capability
bit to be cleared.
This fixes issues where the link would not come up at boot time, or when
the Asym Pause bit was set later on.
As a20-olinuxino-lime2 has Micrel KSZ9031RNXCC-TR Gigabit PHY since
revision H, so we need to use Micrel PHY driver on those devices.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Remove "a" character from the first line of patch
738-v5.14-01-net-dsa-qca8k-fix-an-endian-bug-in-qca8k-get-ethtool.patch
Otherwise `git am` fails to apply this patch which is annoying when
trying to do some development / rebasing.
Signed-off-by: Marek Behún <kabel@kernel.org>
uDPU has 2 LM75 compatible temperature sensors, so include the driver for
them by default in order to utilize them.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
uDPU provides a FIT based initramfs, but currently gets stuck after U-boot
starts the kernel at "Starting kernel..".
It is due to the load address being too low, so increase it in order to get
the initramfs booting again.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
As the upcoming release will be based on Linux 5.10 only, remove all
kernel configuration as well as patches for Linux 5.4.
There were no targets still actively using Linux 5.4.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Also known as the "Xiaomi Router AX3200" in western markets,
but only the AX6S is widely installation-capable at this time.
SoC: MediaTek MT7622B
RAM: DDR3 256 MiB (ESMT M15T2G16128A)
Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG)
WLAN: 2.4/5 GHz 4T4R
2.4 GHz: MediaTek MT7622B
5 GHz: MediaTek MT7915E
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531B
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8
Power: 12 VDC, 1.5 A
Notes:
U-Boot passes through the ethaddr from uboot-env partition,
but also has been known to reset it to a generic mac address
hardcoded in the bootloader.
However, bdata is also populated with the ethernet mac addresses,
but is also typically never written to. Thus this is used instead.
Installation:
1. Flash stock Xiaomi "closed beta" image labelled
'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'.
(MD5: 5eedf1632ac97bb5a6bb072c08603ed7)
2. Calculate telnet password from serial number and login
3. Execute commands to prepare device
nvram set ssh_en=1
nvram set uart_en=1
nvram set boot_wait=on
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
4. Download and flash image
On computer:
python -m http.server
On router:
cd /tmp
wget http://<IP>:8000/factory.bin
mtd -r write factory.bin firmware
Device should reboot at this point.
Reverting to stock:
Stock Xiaomi recovery tftp that accepts their signed images,
with default ips of 192.168.31.1 + 192.168.31.100.
Stock image should be renamed to tftp server ip in hex (Eg. C0A81F64.img)
Triggered by holding reset pin on powerup.
A simple implementation of this would be via dnsmasq's
dhcp-boot option or using the vendor's (Windows only)
recovery tool available on their website.
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
Telco X1 Pro is a Cat12 LTE-A Pro modem router.
Vendor firmware is based on a recent version of OpenWrt.
Flashing is possible via CLI using sysupgrade -F -n
The serial headers allow bootloader and console access
Serial setting: 115200 8N1
Brief Specifications:
IPQ4019 SoC
32MB flash
512MB RAM
4x gigabit LAN
1x gigabit WAN
Dual-band Wave-2 wifi
2x SMA LTE antenna connectors
2x RP-SMA wifi antennas
1x USB 2.0 port
1x Reset button
Serial headers installed
1x Nano SIM tray
1x Quectel EM-12G LTE-A Pro modem
1x M.2 slot attached to USB 3.0
1x internal micro SD card slot
Signed-off-by: Nicholas Smith <nicholas@nbembedded.com>
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz)
- Switch: 1 WAN, 4 LAN (Gigabit)
- Buttons: Reset, WiFi Toggle, WPS
- LEDs: Power, Internet, WiFi 2.4G WiFi 5G
The R1 revision is identical to the A1 revision except
- No Config2 Parition, therefore
- factory partition resized to 64k from 128K
- Firmware partition offset is 0x50000 not 0x60000
- Firmware partitions size increased by 64K
- Firmware partition type is "denx,uimage", not "sge,uimage"
- Padding of image creation "uimage-padhdr 96" removed
Installation:
Update to the last D-Link firmware through web-ui before OpenWRT
installation then follow the instructions to patch your device using
D-Link FailsafeUI.
- D-Link FailsafeUI:
Power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing, then jack into any lan port and manually assign a static IP
address in 192.168.0.0/24 other than 192.168.0.1 (e.g. 192.168.0.2)
and go to http://192.168.0.1
Flash with the factory image.
Signed-off-by: Igor Nazarov <tigron.dev@gmail.com>
Some vendors like Seeedstudio in their product [1] with Raspberry Pi
Compute Module 4 uses Microchip LAN7800 (USB 3.0 to Gigabit
Ethernet Bridge) - USB 3.0 extended from PCIe of CM4.
lsusb output:
```
Bus 002 Device 002: ID 0424:7800 Microchip LAN7800
```
Raspberry Pi 4 and even Compute Module 4 has many resources available
and for just one kernel module it is not necessary to add additional specific CM4 profiles.
Let's include it by default, so the both Ethernet ports will be usable
to have better user-experience. Because previous generation of Raspberry
Pi included LAN7800 Gigabit Ethernet by default and it is enabled there
[2] in kernel without additional kernel module, which was added recently [3].
After this commit in dmesg can be found this:
```
root@OpenWrt:~# dmesg | grep lan
[ 7.038889] lan78xx 2-3:1.0 (unnamed net_device) (uninitialized): int urb period 64
[ 7.090484] usbcore: registered new interface driver lan78xx
```
Tested and works with sysupgrade image.
[1] https://www.seeedstudio.com/Dual-GbE-Carrier-Board-with-4GB-RAM-32GB-eMMC-RPi-CM4-Case-p-5029.html
[2] 32c74552b2/target/linux/bcm27xx/bcm2709/config-5.4 (L437)
[3] 31647d8be8
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Kernel 5.6 introduced a new config symbol SERIAL_8250_16550A_VARIANTS.
In kernel 5.8, this symbol was changed to default to on on !x86, as some
embedded devices still use 16650A variants. Let's play safe here and
enable this symbol in the generic config, to avoid others from running
into this problem and having to spend several hours trying to bisect
this problem. While we could disable the symbol in the x86 target
configs, a 20ms boot time reduction really isn't worth the time wasted
on bisecting this issue.
Matt discovered this problem while working on adding support for the
WatchGuard Firebox M200 to the qoriq target, where it caused some
characters to be missing on the console output.
Reported-by: Matt Fawcett <mattytap@icloud.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
- fix eth0 eth1 sharing same mac so it conforms to the behavior stated
in the original commit and the way it is in vendor firmware :
WAN is label, LAN is label +1 and WLAN is label +2
- add default leds config
- add default network config
Signed-off-by: Pascal Coudurier <coudu@wanadoo.fr>
Buildbot has reported following issue while crunching mpc85xx/p1010
subtarget:
Extreme Networks WS-AP3825i (WS_AP3825I) [N/y/?] (NEW)
Fix it by disabling that config symbol in target kernel config and while
at it fix DTS whitespace issue.
Fixes: 7e614820a8 ("mpc85xx: add support for Extreme Networks WS-AP3825i")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Without a partition subnode ofpart_core still parses direct subnodes as
partitions, but it ignores nodes with a compatible property. Due to
this, the switch to nvmem-cells made the urlader partition inaccessible.
As a result, the wireless network was broken, as the calibration data
is read from that partition by a script.
Fixes: #8983
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
The &spi node has #address-cells = <1> and #size-cells = <0>. Drop the
extra 0 in the reg property from the SPI flash node to ensure it's
number of cells matches the definition in the parent node. This also
makes the reg property for the SPI flash node consistent with all other
VR9 boards.
Fixes: eae6cac6a3 ("lantiq: add support for AVM FRITZ!Box 7362 SL")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Timo Schroeder reported:
"The TP-Link Archer VR2600v is stuck in a boot loop on written
snapshot image. It's able to boot using the snapshot uimage
though, but there ath10k firmware can't be found.
21.02.2 release version doesn't have either problem."
The VR2600v has a 512 byte header at the beginning of the
firmware that needs to be accounted for.
Fixes: f6a01d7f5c ("ipq806x: convert TP-Link Archer VR2600v to denx,uimage")
Reported-by: Timo Schroeder <der.timosch@gmail.com>
References: <https://github.com/openwrt/openwrt/issues/9467>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware:
- SoC: Freescale P1020
- CPU: 2x e500v2 @ 800MHz
- Flash: 64MiB NOR (1x Intel JS28F512)
- Memory: 256MiB (2x ProMOS DDR3 V73CAG01168RBJ-I9H 1Gb)
- WiFi1: 2.4+5GHz abgn 3x3 (Atheros AR9590)
- Wifi2: 5GHz an+ac 3x3 (Qualcomm Atheros QCA9890)
- ETH: 2x PoE Gigabit Ethernet (2x Atheros AR8035)
- Power: 12V (center-positive barrel) or 48V PoE (active or passive)
- Serial: Cisco-compatible RJ45 next to 12V power socket (115200 baud)
- LED Driver: TI LV164A
- LEDs: (not functioning)
- 2x Power (Green + Orange)
- 4x ETH (ETH1 + ETH2) x (Green + Orange)
- 2x WiFi (WiFi2 + WiFi1)
Installation:
1. Grab the OpenWrt initramfs <openwrt-initramfs-bin>, e.g.
openwrt-mpc85xx-p1020-extreme-networks_ws-ap3825i-initramfs-kernel.bin.
Place it in the root directory of a DHCP+TFTP server, e.g. OpenWrt
`dnsmasq` with configuration `dhcp.server.enable_tftp='1'`.
2. Connect to the serial port and boot the AP with options
e.g. 115200,N,8. Stop autoboot in U-Boot by pressing Enter after
'Scanning JFFS2 FS:' begins, then waiting for the prompt to be
interrupted. Credentials are identical to the one in the APs
interface. By default it is admin / new2day: if these do not work,
follow the OEM's reset procedure using the reset button.
3. Set the bootcmd so the AP can boot OpenWrt by executing:
```uboot
setenv boot_openwrt "cp.b 0xEC000000 0x2000000 0x2000000; interrupts off; bootm start 0x2000000; bootm loados; fdt resize; fdt boardsetup; fdt chosen; bootm prep; bootm go;"
setenv bootcmd "run boot_openwrt"
saveenv
```
If you plan on going back to the vendor firmware - the bootcmd for it
is stored in the boot_flash variable.
4. Load the initramfs image to RAM and boot by executing
```uboot
setenv ipaddr <ipv4 client address>;
setenv serverip <tftp server address>;
tftpboot 0x2000000 <openwrt-initramfs-bin>;
interrupts off;
bootm start 0x2000000;
bootm loados;
fdt resize;
fdt boardsetup;
fdt chosen;
bootm prep;
bootm go;
```
5. Make a backup of the "firmware" partition if you ever wish to go back
to the vendor firmware.
6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp
folder.
7. Flash OpenWrt using sysupgrade.
```ash
sysupgrade /tmp/<openwrt-sysupgrade-bin>
```
Notes:
- We must step through the `bootm` process manually to avoid fdt
relocation. To explain: the stock U-boot (and stock Linux) are configured
with a very large CONFIG_SYS_BOOTMAPSZ (and the device's stock Linux
kernel is configured to be able to handle it). The U-boot version
predates the check for the `fdt_high` variable, meaning that upon fdt
relocation, the fdt can (and will) be moved to a very high address; the
default appears to be 0x9ffa000. This address is so high that when the
Linux kernel starts reading the fdt at the beginning of the boot process,
it encounters a memory access exception and panics[5]. While it is
possible to reduce the highest address the fdt will be relocated to by
setting `bootm_size`, this also has the side effect of limiting the
amount of RAM the kernel can use[3].
- Because it is not relocated, the flattened device tree needs to be
padded in the build process to guarantee that `fdt resize` has
enough space.
- The primary ethernet MAC address is stored (and set) in U-boot; they are
shimmed into the device tree by 'fdt boardsetup' through the
'local-mac-address' property of the respective ethernet node, so OpenWrt
does not need to set this at runtime. Note that U-boot indexes the
ethernet nodes by alias, which is why the device tree explicitly aliases
ethernet1 to enet2.
- LEDs do not function under OpenWrt. Each of 8 LEDs is connected to an
output of a TI LV164A shift register, which is wired to GPIO lines and
operates through bit-banged SPI. Unfortunately, I am unable to get the
spi-gpio driver to recognize the `led_spi` device tree node at all, as
confirmed by patching in printk messages demonstrating
spi-gpio.c::spi_gpio_probe never runs. It is possible to manually
articulate the shift register by exporting the GPIO lines and stepping
their values through the sysfs.
- Though they do not function under OpenWrt, I have left the pinout details
of the LEDs and shift register in the device tree to represent real
hardware.
- An archive of the u-boot and Linux source for the AP3825i (which is one
device of a range of devices code-named 'CHANTRY') be found here[1].
- The device has an identical case to both the Enterasys WS-AP3725i and
Adtran BSAP-2030[2] (and potentially other Adtran BSAPs). Given that
there is no FCC ID for the board itself (only its WLAN modules), it's
likely these are generic boards, and even that the WS-AP3725i is
identical, with only a change in WLAN card. I have ordered one to confirm
this.
- For additional information: the process of porting the board is
documented in an OpenWrt forum thread[4].
[1]: magnet:?xt=urn:btih:f5306a5dfd06d42319e4554565429f84dde96bbc
[2]: https://forum.openwrt.org/t/support-for-adtran-bluesocket-bsap-2030/48538
[3]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168/29
[4]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168
[5]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168/26
Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
This patch adds support for the Netgear WN3100RPv2
http://www.netgear.com/support/product/wn3100rpv2.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This device seems to be same hardware as a WN3000RPv3
Flash instructions:
- Use the Netgear WebUI to upgrade to OpenWRT using the factory image
(see note below),
- Use the sysupgrade image for upgrading versions from OpenWRT,
- TFTP recovery procedure can be used to flash the factory image
(preferred method).
Note:
- The WebUI may not reboot automatically, wait at least 5 minutes before
powercycling the device
Flashing using TFTP:
- Set you IP address to 192.168.1.10/24 (no gateway)
- Connect your machine to the Ethernet port
- Power off the device and wait for 10 seconds,
- Hold the reset button and power on the device (do not release reset),
- Hold the reset button until the green light is flashing (Approx. 15s)
- launch tftp, set mode to binary and connect to 192.168.1.1
- put the factory firmware image
- All leds will switch off (like a power off), this is normal
- Wait for the device to reboot in the new OpenWRT image (max 5 mins)
- The first boot will take longer than usual.
- After boot, the Device IP on the ethernet port is 192.168.1.1
Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com>
[drop unneeded includes in dts, wrap commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
