The dual-boot partition layout for the Zyxel GS1900 switches results in
6.9MB for both kernel and rootfs. Depending on the package selection,
this may already leave no space for the user overlay.
Merge the two firmware partitions, effectively dropping dual boot
support with OpenWrt. This results in a firmware partition of 13.9MB,
which should leave some room for the future.
To maintain install capabilites on new devices, an image is required
that still fits inside the original partition. The initramfs is used as
factory install image, so ensure this meets the old size constraints.
The factory image can be flashed via the same procedure as vendor images
when reverting to stock, can be installed from stock, or can be launched
via tftpboot.
Link: https://github.com/openwrt/openwrt/issues/16439
Link: https://github.com/openwrt/openwrt/pull/16442
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
GPIO 5 on the RTL8231 is defined reset the system, but fails to actually
do so. This triggers a kernel a number of warnings and backtrace for
GPIO pins that can sleep, such as the RTL8231's. Two warnings are
emitted by libgpiod, and a third warning by gpio-restart itself after it
fails to restart the system:
[ 106.654008] ------------[ cut here ]------------
[ 106.659240] WARNING: CPU: 0 PID: 4279 at drivers/gpio/gpiolib.c:3098 gpiod_set_value+0x7c/0x108
[ Stack dump and call trace ]
[ 106.826218] ---[ end trace d1de50b401f5a153 ]---
[ 106.962992] ------------[ cut here ]------------
[ 106.968208] WARNING: CPU: 0 PID: 4279 at drivers/gpio/gpiolib.c:3098 gpiod_set_value+0x7c/0x108
[ Stack dump and call trace ]
[ 107.136718] ---[ end trace d1de50b401f5a154 ]---
[ 111.087092] ------------[ cut here ]------------
[ 111.092271] WARNING: CPU: 0 PID: 4279 at drivers/power/reset/gpio-restart.c:46 gpio_restart_notify+0xc0/0xdc
[ Stack dump and call trace ]
[ 111.256629] ---[ end trace d1de50b401f5a155 ]---
By removing gpio-restart from this device, we skip the restart-by-GPIO
attempt and rely only on the watchdog for restarts, which is already the
de facto behaviour.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Userspace handling is deprecated.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17311
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add the label-mac-device alias.
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Link: https://github.com/openwrt/openwrt/pull/17313
Signed-off-by: Robert Marko <robimarko@gmail.com>
The AR8035 PHY is used in most Octeon boards supported by OpenWRT (all
the Ubiquiti routers at least). To be able to use its PHY-specific
functionality (cable testing, LED Control, ...) it should be built on
Octeon. It also needs the regulator framework, so enable that as well.
These boards are not space-constrained, so this really has no downsides.
Tested on an EdgeRouter Lite, cable tests now work with ethtool-full.
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Link: https://github.com/openwrt/openwrt/pull/17318
Signed-off-by: Robert Marko <robimarko@gmail.com>
This backport patch inserted suspend/resume callbacks
for the wrong PHY driver.
The fixed patch is needed for Huawei AP5030DN
to initialize its second PHY.
Refresh all affected patch with make target/linux/refresh.
Fixes: 06cdc07f8c ("ath79: add support for Huawei AP5030DN")
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/17312
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sets openwrt,netdev-name for the gmac nodes in the dts of BPI-R4 which
correspond to the two sfp slots. By default they are automatically
named as eth1 and eth2 in bad order, however 'SFP1-WAN' and 'SFP2-LAN'
are printed on the PCB and the official metal case has labels 'SFP-WAN'
and 'SFP-LAN'. Thus, label the ports accordingly to match the
board/case labels.
The COMPAT_VERSION is increased to denote that configuration has to be
adjusted manually.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Sets openwrt,netdev-name for the gmac1 node in the dts of BPI-R3, which
corresponds to the sfp1 slot, to have a proper naming and match the
label on the official BPI-R3 metal case. This renames the port from eth1
to sfp1.
The COMPAT_VERSION is increased to denote that configuration has to be
adjusted manually.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Add support in filogic subtarget for our own custom property
`openwrt,netdev-name` in the device tree instead of `label` for
renaming interfaces. This was suggested upstream to avoid potential
conflicts [1].
[1] https://lore.kernel.org/netdev/20240709124503.pubki5nwjfbedhhy@skbuf/
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Userspace handling is deprecated. MAC address stuff needs to remain
handled in userspace as it's encrypted. Maybe an NVMEM driver can be
written in the future...
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17276
Signed-off-by: Robert Marko <robimarko@gmail.com>
The qusb_phy node looks for the following supply:
"vdd", "vdda-pll", "vdda-phy-dpdm"
And ssphy node looks for the following supply:
"vdda-phy", "vdda-pll"
So fix the usb regulator supply for RT-AX89X.
Fixes: 1306237 ("qualcommax: use PHY regulator for USB GPIO")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17290
Signed-off-by: Robert Marko <robimarko@gmail.com>
Not all Kirkwood systems have the Marvell MV88E6XXX switches.
Drop those from the generic config and add them as modules
in the systems that have it.
This was inferred by inspecting the upstream DTS files for any
mv88e* strings and adding the mv88e6xxx kmod package to those
that have an upstream device tree with an MV88E6xxx switch
and an OpenWrt image target.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is using mac-base and so a 0 needs to be added.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17274
Signed-off-by: Robert Marko <robimarko@gmail.com>
Images for xrx200 8M flash are either not building due to image
size (TD-W8970, TD-W8980) or building such that the available
free space in the overlayfs is too little to be useful.
To keep images for these devices buildable, move them into a
small flash variant of the xrx200 subtarget. As these devices
are NOR flash only, remove NAND and UBI references from the
kernel config to gain some additional image size reduction.
The apparent 8M flash devices Arcadyan VGV7510KW22-brn,
Arcadyan VGV7519-brn and Lantiq Easy80920-nor seem to exist in
order to create special "factory" installation images for these
devices (which actually have larger flash: 16MB for the
Arcardyan devices; 64MB for the Lantiq device). As a
considerable amount of surgery would appear to be required to
the uboot-lantiq package structure to separate the "factory"
from the "sysupgrade" device recipes for these devices they
remain in the xrx200 target - if factory images aren't now
created, 23.05.x factory images should suffice for initial
installation.
Tested on: Netgear DM200, TP-Link TD-W8980,
AVM Fritz7490 (xrx200 subtarget: image build only)
Fixes: https://github.com/openwrt/openwrt/issues/16761
Signed-off-by: Andrew MacIntyre <andymac@pcug.org.au>
Link: https://github.com/openwrt/openwrt/pull/17113
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The PHY can handle turning off the GPIOs when turning off all USB ports.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17192
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
- Device: ASUS 4g-AX56
- SoC: MT7621AT
- Flash: 128MB
- RAM: 512MB
- Switch: 1 WAN, 4 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LTE : Fibocom FG621-EA
- LEDs: 1x POWER (white, configurable)
1x 2.4G (white, not configurable)
1x 5G (white, not configurable)
1x WAN (white, not configurable)
1x 3G/4G (white, not configurable)
3x signal (white, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.0.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.0.1
Input TFTP server's IP address: 192.168.0.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_4g-ax56-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Notice:
- LTE module is disable after flash openwrt image so you must active LTE by following two AT command
echo -e "AT+GTAUTOCONNECT=1\r\n" > /dev/ttyUSB0
echo -e "AT+GTRNDIS=1,1\r\n" > /dev/ttyUSB0
- After finish AT command once, you don't need to input command later even if reboot/restore default
Signed-off-by: Chuncheng Chen <ccchen1984@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16752
Signed-off-by: John Crispin <john@phrozen.org>
Hardware
* Mediatek MT7620A + Mediatek MT7610EN
* 64MB RAM
* 8MB NAND (Winbond 25064FVSIG )
Both 2.4GHZ and 5GHZ are working, it is enabled by default since there is no
physical ethernet port in the device.
All LED's and buttons work.
UART: 57600 8N1 3.3V
Installation
Upload the openwrt-ramips-mt7620-trendnet_tha103ac-initramfs-kernel.bin via
the manufacturer firmware upgrade page on the device.
Upon reboot wait +- 3 mins until the green power LED is not flashing anymore
(do not be tempted to switch the device off while the LED is flashing, unless
you are ready for soldering and TTL) and then press the WPS button to enable
the default OpenWrt Wifi AP, the BLUE wifi LED will start flash.
Then install openwrt-ramips-mt7620-trendnet_tha103ac-squashfs-sysupgrade.bin
via OpenWrt.
The integrated power monitoring and relay do not work in OpenWrt as the PL7223
chip source/documentation is unavailable.
Recovery
Mis-configuration can be dealt with using the RESET button to reset to factory,
worst case scenario will require some serious work and soldering, there's pads
on the PCB for both the UART and ETH0, and I soldered and tested that it does
work.
You will have to power the board using the header pins GND & 5V, see the 8-pin
header socket.
Signed-off-by: Die Peter Pan <diepeterpan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17114
Signed-off-by: John Crispin <john@phrozen.org>
The original ar71xx version of this device used 1002 as mac address for
both ethernet and wireless. The ath79 version inexplicably changes this
to 2, which seems to be done nowhere else in ath79, indicating it's
bogus.
Restore previous ar71xx assignment. 1002 is used as an ethernet
interface with some other devices as well.
Also remove the bogus caldata userspace extraction. The size is bogus
and it's already handled in dts.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17083
Signed-off-by: John Crispin <john@phrozen.org>
NRadio C8-668GL is a Wi-Fi 6 5G cellular router based on MediaTek MT7981B SoC.
- **SoC**: MediaTek MT7981B (2x Cortex-A53, 1.3GHz)
- **RAM**: Nanya NT5AD512M16C4-JR 1GB DDR4
- **Flash**: ESMT FC51L08SFY3A 8GB eMMC
- **Ethernet**:
- 1x 2.5GbE (via GMAC0 and GPY211 PHY, shared with MT7531AE)
- 3x 10/100/1000 Mbps (via MT7531AE, connected to GMAC0)
- 5G Modem: GMAC1 (via GPY211 PHY - RTL8125BG - RM520N-GL)
- **Wi-Fi**: MediaTek MT7976CN (2.4GHz/5GHz, 802.11ax, 2x2 MIMO, AX3000)
- **Buttons**: Reset, WPS
- **LEDs**: Power, 5G, 4G, WiFi
- **SIM Slot**: 1x Nano SIM
- **5G Modem**: Quectel RM520N-GL (Snapdragon™ X62)
- **Power**: 12V/2A DC, 5.5×2.1 connector
The MAC addresses are derived from the `fac_mac` field in the `bdinfo` partition, formatted as `fac_mac = HWMAC`. The allocation is as follows:
| Vendor | OpenWrt Interface | Address | Notes |
|---------|-------------------|---------------|------------------------------------------------|
| LAN | br-lan | Label MAC | Default |
| WAN | lan4 | Label MAC+1 | Only when lan4 is switched to WAN |
| 2.4GHz | phy0-ap0 | Label MAC | |
| 5GHz | phy1-ap0 | Label MAC | (Local Admin bit set) |
| Modem | eth1 | Label MAC+2 | |
1. Log in to the router via `http://192.168.66.1`/.
2. Upgrade the official firmware to dual-system mode.
3. Select **Burn second system** and upload the `sysupgrade.bin` image.
- Download the image from the OpenWrt build system or build it yourself using the OpenWrt buildroot.
4. Wait for 30 seconds and click **Switch system**.
5. The device will reboot and switch to OpenWrt.
Set the U-Boot environment variable `boot_system=0` and reboot:
```bash
fw_setenv boot_system 0
```
Power off the router, hold the **WPS button**, and power it back on.
1. Rename the stock firmware file to **`recovery.bin`**.
2. Set your PC's Ethernet IP to **192.168.1.88** and connect it to the lan1 port on the router.
3. Run a TFTP server and place the `recovery.bin` file in its root directory.
4. Power off the router, press and hold the **Reset button**, and power it back on.
5. Release the Reset button when the TFTP server shows activity.
6. Wait for the router to flash the firmware and reboot automatically.
- By default, `lan4` is part of `br-lan` and uses the label MAC address.
- To query the RM520N-GL module, use the following command:
```bash
cat /dev/ttyUSB2 & printf 'ATI\r\n' > /dev/ttyUSB2
```
Signed-off-by: Yaoguang Bai <0xdeadc0de@badguys.club>
Link: https://github.com/openwrt/openwrt/pull/17093
Signed-off-by: John Crispin <john@phrozen.org>
Upstream uses devm_reset_control_array_get_optional_shared, which does
not use names. reset-names is also not specified in the documentation.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17118
Signed-off-by: John Crispin <john@phrozen.org>
Both generic-ehci.yaml and generic-ohci.yaml state that phy-names is to
only be usb.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17118
Signed-off-by: John Crispin <john@phrozen.org>
This matches the upstream PHY driver, which removed it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17118
Signed-off-by: John Crispin <john@phrozen.org>
One is already present. The other one can be implemented in terms of the
PHY.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17250
Signed-off-by: John Crispin <john@phrozen.org>
Instead of using regulator-output to manually control USB GPIO, let the
PHY handle it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17221
Signed-off-by: John Crispin <john@phrozen.org>
We have seen hung devices and failures during SPI transactions on
Fritzbox devices with a gluon based freifunk network. We have narrowed
down that disabling DMA for spi fixes the problem, so disable dma for
the SPI controller on the Fritzbox 4040.
Signed-off-by: Rouven Czerwinski <rouven@czerwinskis.de>
Link: https://github.com/openwrt/openwrt/pull/15966
Signed-off-by: John Crispin <john@phrozen.org>
Use ath11k_patch_mac and ath11k_set_macflag functions
instead of fix_wifi_mac script.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17230
Signed-off-by: Robert Marko <robimarko@gmail.com>
Change partition table in dts file.
Change DEVICE_COMPAT_VERSION
Enable automatic build.
To take advantage of the bigger kernel partition,
the uboot environment has to be changed:
setenv nboot 'nand read 0x81000000 0x60000 0x500000; bootm 0x81000000'
setenv bootcmd 'run nboot'
saveenv
Of course you need a u-boot capable of handling this.
The u-boot discussed in this forum thread:
https://forum.openwrt.org/t/zyxel-p2812hnu-f1-u-boot/100281
should be able to handle kernels up to an uncompressed size of 16MiB.
Signed-off-by: Isaac de Wolff <idewolff@gmx.com>
Link: https://github.com/openwrt/openwrt/pull/17209
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The device path to the devices changed. Migrate the wifi
configurations from the old path to the new one. This is needed to
migrate Wireless configurations from OpenWrt 23.05 to OpenWrt 24.10.
This script is based on these two files:
target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
Fixes: 0ef9274721 ("mediatek: filogic: move mt7981 on-SoC blocks to "soc" node in DT")
Fixes: https://github.com/openwrt/openwrt/issues/17174
Link: https://github.com/openwrt/openwrt/pull/17210
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The vendor U-Boot on the Cudy WR3000 assign random mac addresses on boot
and set the 'local-mac-address' property which prevents Openwrt from
assigning the correct address from evmem.
This patch removes the alias for ethernet0 so that U-Boot doesn't add
the property.
Related to: a55ab9e134 ("mediatek: filogic: prevent faulty mac address assignment")
Fixes: https://github.com/openwrt/openwrt/issues/15587
Signed-off-by: Ondřej Niesner <ondra.niesner@seznam.cz>
Link: https://github.com/openwrt/openwrt/pull/17201
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a simple conversion to dts.
68ac3f2cdd states that the 5ghz wifi address is calculated from ART 0
+ 2.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17066
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
* Mediatek MT7981BA
* 256 MB SPI-NAND
* 512 MB DDR4 RAM
* MT7976CN DBDC AX Wi-Fi
* MediaTek MT7531AE (3x LAN Gigabit ports) + Internal Gbe Phy (1x WAN Gigabit port)
* 4x LED (power, internet, fn, wifi)
* 3x buttons (wps, fn, reset)
* 1x USB 3.0 port
Serial Interface:
* 3 Pins GND, RX, TX
* Settings: 115200, 8N1
Notes:
* The device supports dual boot mode
* Fn led reassigned to wlan 2.4
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-mediatek-filogic-keenetic_kn-3811-squashfs-factory.bin"
to "KN-3811_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17135
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add patch to fix failure to build package/devel/perf when
CONFIG_TARGET_OPTIMIZATION has -O3 enabled with this error:
```
In function 'elf_close',
inlined from 'elf_close' at elf.c:41:6,
inlined from 'elf_find_func_offset_from_file' at elf.c:267:2:
elf.c:45:9: error: 'elf_fd.elf' may be used uninitialized [-Werror=maybe-uninitialized]
45 | elf_end(elf_fd->elf);
| ^~~~~~~~~~~~~~~~~~~~
elf.c: In function 'elf_find_func_offset_from_file':
elf.c:260:23: note: 'elf_fd.elf' was declared here
260 | struct elf_fd elf_fd;
| ^~~~~~
In function 'elf_close',
inlined from 'elf_close' at elf.c:41:6,
inlined from 'elf_find_func_offset_from_file' at elf.c:267:2:
elf.c:46:9: error: 'elf_fd.fd' may be used uninitialized [-Werror=maybe-uninitialized]
46 | close(elf_fd->fd);
| ^~~~~~~~~~~~~~~~~
elf.c: In function 'elf_find_func_offset_from_file':
elf.c:260:23: note: 'elf_fd.fd' was declared here
260 | struct elf_fd elf_fd;
| ^~~~~~
```
Link: https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next.git/commit/?id=fab45b962749
Signed-off-by: Pavel Shirov <nstorm.ahoy166@silomails.com>
Link: https://github.com/openwrt/openwrt/pull/17141
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Create a separate header files fallback-sprom.h
for BCMA and SSB Fallback SPROM Driver
to add function prototypes to fallback-sprom.c as well.
This prevents missing function prototype errors.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/17138
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add NETGEAR_BOARD_ID and NETGEAR_HW_ID to DEVICE_VARS as multiple devices
set them in their recipes, so without them being added to DEVICE_VARS then
simply the value from last recipe that gets evaluated is used and images
are generated with the wrong ID-s.
Link: https://github.com/openwrt/openwrt/pull/17203
Signed-off-by: Robert Marko <robimarko@gmail.com>
Linksys MR7350 is a 802.11ax Dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ6000 Quad core Cortex-A53(A73) 1.5GHz
* RAM: 512MB of DDR3
* Storage: 256Mb NAND
* Ethernet: 5x1G RJ45 ports (QCA8075)
* WLAN:
* 2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5052 2x2@80MHz or 802.11a/b/g/n/ac/ax 1201 Mbps PHY rate
* LED-s:
* RGB system led
* USB blue led
* Buttons: 1x Soft reset 1x WPS
* Power: 12V DC Jack
Installation instructions:
Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup.
Login with your admin password. The default password can be found on a sticker under the device.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device.
Then you would need to write openwrt to the other partition for it to work
- First Check booted partition:
fw_printenv -n boot_part
- Change the partition:
fw_setenv boot_part 1
or
fw_setenv boot_part 2
depending on the current partition
- Then install Openwrt to the other partition if booted in slot 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin alt_kernel
- If in slot 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin kernel
Co-Authored-by: Chukun Pan <amadeus@jmu.edu.cn>
Co-Authored-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Vladyslav Andreichykov <vladdrako007@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14807
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace regulator consumer is rather usefull so enable it for ipq60xx
as well and remove from ipq807x only kernel config.
Link: https://github.com/openwrt/openwrt/pull/14807
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for FORESEE F35SQA001G SPI NAND.
Similar to F35SQA002G, but differs in capacity.
Datasheet:
- https://cdn.ozdisan.com/ETicaret_Dosya/704795_871495.pdf
Tested on Xiaomi AX3000T flashed with OpenWRT.
Signed-off-by: Bohdan Chubuk <chbgdn@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16915
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Specifications:
SoC: Qualcomm IPQ6000 1.5GHz
RAM: NTCC256M16ER-EK 512MiB
Flash: W29N01HZSINA 128MiB
ETH: QCA8075 (3x LAN, 1x WAN)
WLAN1: 2.4GHz 802.11b/g/n/ax 2x2
WLAN2: 5GHz 802.11a/n/ac/ax 2x2
Power: DC 12V 1.5A
Button: Reset, Wps
USB: 1x 2.0
Flash instructions:
1. Download the initramfs image, rename it to
initramfs.itb, host it with the tftp server.
2. Interrupt U-Boot and run these commands:
tftpboot initramfs.itb
bootm
3. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15940
Signed-off-by: Robert Marko <robimarko@gmail.com>
