Device support for Belkin F9K1109v1 was added using set_usb_led()
although this was removed in 772b27c207 ("ramips: set F5D8235 v1
usb led trigger via devicetree").
Use ucidef_set_led_usbport() instead.
Fixes: f2c83532f9 ("ramips: add support for Belkin F9K1109v1")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rephrase commit title and message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch does the following:
- rename "devdata" flash partition and make it read-only
- switch from gpio-keys-polled to gpio-keys
- add missing power LED
- set correct PCI ID to compatible string in wifi node
- remove ralink,5ghz property in wifi node
- provide label MAC address
Rename devdata partition to devconf as indicated in the stock firmware
partition table:
00030000-00040000: "devdata"
00040000-00050000: "devconf"
Power LED can be controlled by SoC GPIO. Add it in the dts leds node.
RT3092L supports only bgn mode, so it is unnecessary to disable 5GHz band.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Ethernet MAC address setup has been broken since c3e420f28c. Restore
original setting.
Fixes: c3e420f28c ("ramips: Add support for D-Link DCH-M225")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
So far, MAC address assignment in ramips has contained a default
case, which defined wan_mac = eth0 + 1 for _every_ device not
having an explicit case there.
This is not desirable, as many device supporters will just not
care or know about this definition, so another MAC address will be
introduced by accident. In some cases the wan_mac is assigned
although it is not needed, in other cases even addresses not
dedicated to the device will be used (e.g. wan_mac actually is
eth0 - 1, but during support nobody cared, so eth0 + 1 is used now,
which might actually belong to another device ...).
Thus, in this PR the former default case is converted to an
explicit case. This one comprises all devices not being accounted
for by other cases, reduced by those not having wan at all.
The big number of entries for this node might be another indication
that many of them wouldn't actually be there if there hadn't been
default wan_mac setup.
In exchange, the current "do nothing" case can be removed, as it
will be the new default case.
The devices being put in the newly created explicit case were
determined as follows:
1. Create a list of all devices based on the DTS files.
2. Remove all devices already having an explicit entry setting
their address.
3. Remove all devices that only have lan set up in the first part
of 02_network:
mt7620:
- alfa-network,tube-e4g
- asus,rp-n53
- buffalo,wmr-300
- comfast,cf-wr800n
- edimax,ew-7476rpc
- edimax,ew-7478ac
- elecom,wrh-300cr
- hnet,c108
- kimax,u25awf-h1
- kimax,u35wf
- kingston,mlw221
- kingston,mlwg2
- microduino,microwrt
- netgear,ex2700
- netgear,ex3700
- netgear,wn3000rp-v3
- planex,cs-qr10
- planex,mzk-ex300np
- planex,mzk-ex750np
- ravpower,wd03
- sercomm,na930
- yukai,bocco
- zbtlink,zbt-cpe102
- zte,q7
mt7621:
- gnubee,gb-pc1
- gnubee,gb-pc2
- linksys,re6500
- mikrotik,rbm11g
- netgear,ex6150
- thunder,timecloud
- tplink,re350-v1
- tplink,re650-v1
mt76x8:
- alfa-network,awusfree1
- d-team,pbr-d1
- glinet,vixmini
- vocore,vocore2-lite
- tama,w06
- tplink,tl-mr3020-v3
- tplink,tl-wa801nd-v5
- tplink,tl-wr802n-v4
- tplink,tl-wr902ac-v3
- vocore,vocore2
- widora,neo-16m
- widora,neo-32m
rt288x:
- buffalo,wli-tx4-ag300n
- dlink,dap-1522-a1
rt305x:
- allnet,all0256n-4m
- allnet,all0256n-8m
- allnet,all5002
- allnet,all5003
- alphanetworks,asl26555-16m
- alphanetworks,asl26555-8m
- asus,wl-330n
- aximcom,mr-102n
- dlink,dcs-930
- easyacc,wizard-8800
- hame,mpr-a2
- hootoo,ht-tm02
- huawei,d105
- intenso,memory2move
- planex,mzk-dp150n
- rt305x dlink,dcs-930l-b1
- sparklan,wcr-150gn
- tenda,3g150b
- tenda,3g300m
- tenda,w150m
- trendnet,tew-638apb-v2
- unbranded,a5-v11
- vocore,vocore-16m
- vocore,vocore-8m
- wansview,ncs601w
- zorlik,zl5900v2
rt3883:
- loewe,wmdr-143n
- omnima,hpm
4. Put the remaining devices in the new case.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
While most of the target's contents are split into subtargets, the
base-files are maintained for the target as a whole.
However, OpenWrt already implements a mechanism that will use (and
even prefer) files in the subtargets' directories. This can be
exploited to make several scripts subtarget-specific and thus save
some space.
In certain cases, keeping files in parent (=target) base-files was
more convenient, and thus no splitting was performed for those.
Note that this will increase overall code lines, but reduce code
per subtarget.
base-files ipk size reduction:
master (mt7621) 60958 B
split (mt7620) 46358 B (- 14.3 kiB)
split (mt7621) 48759 B (- 11.9 kiB)
split (mt76x8) 44948 B (- 15.6 kiB)
split (rt288x) 43508 B (- 17.0 kiB)
split (rt305x) 45616 B (- 15.0 kiB)
split (rt3883) 44176 B (- 16.4 kiB)
Run-tested on:
GL.iNet GL-MT300N-V2 (mt76x8)
D-Link DWR-116 (mt7620)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This removes _all_ occurrences of kmod-usb-core from
DEVICE_PACKAGES and similar variables.
This package is pulled as dependency by one of the following
packages in any case:
- kmod-usb-chipidea
- kmod-usb-dwc2
- kmod-usb-ledtrig-usbport
- kmod-usb-ohci
- kmod-usb2
- kmod-usb2-pci
- kmod-usb3
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[remove kmod-usb-core from EnGenius ESR600]
Signed-off-by: David Bauer <mail@david-bauer.net>
Upstream kernel added support for RAW_APPENDED_DTB on ralink arch
in the following commit:
02564fc89d3d ("ralink: Introduce fw_passed_dtb to arch/mips/ralink")
Use upstream solution and get rid of our OWRTDTB hack.
This commit set DEVICE_DTS to $$(DTS) instead of replacing DTS with
DEVICE_DTS in device profile because DTS variable will be dropped
in later commits.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on mt7621/mt76x8]
Tested-by: Chuanhong Guo <gch981213@gmail.com>
[Tested on rt305x/mt7620]
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
It's no longer needed as all mt7621 devices use DT binding (supported by
upstream mtd code) for specifying "firmware" part format explicitly.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add a new config option to allow to select the default compile
optimization level for the kernel.
Select the optimization for size by default if the small_flash feature is
set. Otherwise "Optimize for performance" is set.
Add the small_flash feature flag to all (sub)targets which had the
optimization for size in their default kernel config.
Remove CC_OPTIMIZE_FOR_* symbols from all kernel configs to apply the new
setting.
Exceptions to the above are:
- lantiq, where the optimization for size is only required for the
xway_legacy subtarget but was set for the whole target
- mediatek, ramips/mt7620 & ramips/mt76x8 where boards should have
plenty of space and an optimization for size doesn't make much sense
- rb532, which has 128MByte flash
Signed-off-by: Mathias Kresin <dev@kresin.me>
THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
The previous fw version require the replacement of the stock bootloader
with u-boot. This prevent an easy stock restore of the original fw.
Now a proper fw util has been developed to manage the stock jboot
bootloader. Therefore make sense have a fw image for the stock
bootloader.
The old fw configuration (u-boot) is not compatible with the new one
and will not be supported anymore.
So at the end 2 image can be generated:
1) factory image with jboot bootloader
openwrt-ramips-rt305x-dwr-512-b-squashfs-factory.bin
2) sysupgrade image with jboot bootloader
openwrt-ramips-rt305x-dwr-512-b-squashfs-sysupgrade.bin
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
- removed upstreamed patches
- 0901-spansion_nand_id_fix.patch is disabled, not clear if it's needed
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: John Crispin <john@phrozen.org>
Some targets need 4K sectors for small flash chips (e.g. some
routerboards, where the entire chip is just one "erase block"), whereas
on other devices 4K sectors lead to horrible flash erase/write
performance.
Set the default limit in the generic kernel configuration to 4 MiB to
ensure that all new platforms don't use 4K sectors for bigger flash
chips. On all existing targets use 16 MiB for now to avoid regressions.
They will be changed individually in follow-up commits.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The kernel 4.4 patches where already removed with the bump to 4.9. Drop
the the subtarget configs as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
CONFIG_SG_POOL symbol is selected only by CONFIG_SCSI, since the last
one is disabled by default then disable CONFIG_SG_POOL by default too.
And explicitly enable it only for platforms that use CONFIG_SCSI.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
In order to have a smaller initramfs image remove all packages not
needed on all devices and add them explicitely for those actually
needing them. Also remove wpad-mini from ramips default package set
and add it to all sub-targets except for MT7621.
While at it reorder packages alphabetically and replace kmod-mt76 with
kmod-mt7603 and/or kmod-mt76x2 depending on the chip actually used on
a specific board.
Hopefully fixes FS#758
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is a follow up to 28110727f1
"ramips: set blocksize for 4MB devices". I've missed to include the
required changes of the kernel configs to enable 4K sector size
support.
The option is only enabled for targets having boards with 4k sector
size flash chips.
Signed-off-by: Mathias Kresin <dev@kresin.me>
There does not seem to be any meaningful difference in generated code.
This will save some time and space on snapshot builds
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- Use default number of uarts (2) for rt288x/rt305x/rt3883/mt7620.
- Allow up to 3 uarts on MT7621 and MT7628.
- Remove unneeded SERIAL_8250_RT288X for MT7628.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch:
* fixes wrong indentation
* fixes wrong names and descriptions (ex. Dlink -> D-Link)
* changes filenames to manufacturer names
* moves oem/unknown manufacturers boards to misc.mk profiles
* combines profiles for boards from the same manufacturers in one file (ex. Olimex)
* fix profile files structure (keep the same convention as in other targets, ex. ar71xx)
in various .mk profiles, in ramips target.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SVN-Revision: 46631
Disable ARCH_NEEDS_CPU_IDLE_COUPLED by-default in generic config, since
only one platfrom (omap) needs them.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44614
CONFIG_MTD_SPLIT_SUPPORT symbol default value is 'y' and many platform
specific configs explicitly enables it, while no one platform disables
this symbol. So place it in generic config and remove from platform
specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44612
CONFIG_GENERIC_NET_UTILS is selected by CONFIG_NET and already enabled
in generic config, so we don't need this symbol in platform specific
configurations.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44611
Most MIPS targets have it disabled, so move the symbol to the generic
configs to keep target configs small.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44583
