Ben Greear reported in his patch:
|Subject: netgear r7800: Fix mac address of radios.
|
|Reloading the driver causes the phyX to change, and that
|caused the MAC address to change.
This is because all ODM/OEMs except QCA bothered to write
the correct MAC address for the ath10k wifi into the
calibration data.
This patch copies over the MAC patching helper functions from ipq40xx's
target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
file and converts all the devices to patch the correct MACs into the
extracted calibration data before it gets sent to the driver, which sets
up the device with the correct MAC address. It also removes the entries
in the 10_fix_wifi_mac file as they have served their purpose for good.
Please note the C2600: There is conflicting information on what
the offset for the second wifi is supposed to be. This patch uses
what was specified in 10_fix_wifi_mac.
According to Ben Greear this method is save to use with the
stock firmware too. As he explained that the stock firmware
messes up rx-bssid mask calculation when the MAC is changed
after the first vif is created.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
- Mark other partitions as read-only for HC5x61
- Only enable USB and PCIe for HC5761/HC5861
HC5661 doesn't have a USB port, and there is nothing attached to its PCIe.
- Fix HC5761 switch ports
HC5761 has only 3 ethernet ports (1x WAN + 2x LAN). Remove unused ports.
- Fix HC5861 5GHz radio
HC5861 has MT7612EN 5GHz WiFi chip, not MT7610EN.
- Fix HC5761/HC5861 WiFi LEDs
After 5GHz is enabled, it becomes wlan0. And 2.4GHz would be wlan1.
- Fix HC5x61 image size
It should be 15872k (0xf80000)
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
In the thread: "ipq806x: add ath10k calibration data MAC addresses patching"
Chuanhong Guo <gch981213@gmail.com> noted that:
"All ath10k calibration data have a checksum at 0x2.
ath10kcal_patch_mac works for QCA9880/QCA9882 only because
the ath10k firmware for these two chips doesn't check the
checksum value. (QCA proprietary driver checks this and
refuses to use caldata with incorrect checksum.)"
This patch updates 11-ath10k-caldata of the ipq40xx target accordingly.
Reported-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This updates the ath10k-ct driver to the version from 2018-12-11 and
selects the ath10k-ct version based on kernel 4.19 by default.
CONFIG_ATH10K_CE was introduced between kernel 4.16 and 4.19 and is a
mandatory option.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the GCC to the next minor release which fixes 178 bugs.
The two removed patches are included in gcc 7.4.0
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
In mainline kernel commit 02c7b25e5f5 ("netfilter: nf_tables: build-in
filter chain type") all chain filters were merged into one file and into
one kernel module to save some memory. The code protected by these
configuration options CONFIG_NF_TABLES_BRIDGE, CONFIG_NF_TABLES_IPV4,
CONFIG_NF_TABLES_ARP, CONFIG_NF_TABLES_IPV6, CONFIG_NF_TABLES_NETDEV and
CONFIG_NF_TABLES_INET was merged into the nft_chain_filter.c file which
is now always compiled into the nf_tables.ko file.
This only happened in kernel 4.19 and OpenWrt has to select these as
modules in older kennel versions. Mark them as build-in in the kernel
4.19 specific kernel configuration file which will then not be
overwritten by the package specific settings which try to make them
modular again.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel commit 0168e8b361 ("netfilter: nat: merge ipv4/ipv6 masquerade
code into main nat module") the CONFIG_NF_NAT_MASQUERADE_IPV4 and
CONFIG_NF_NAT_MASQUERADE_IPV6 kernel configuration option were changed
to bool and the code will not be compiled as a own module any more, but
it will be integrated into nf_nat_ipv4.ko or nf_nat_ipv6.ko to save some
memory.
Activate these options as bool in the generic kernel 4.19 configuration
only, to always build them into the nf_nat_ipv*.ko modules. The kmod
file will still try to select them as module, but the generic
configuration will not be overwritten.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some kernel modules from kmod-ipt-conntrack-extra depend on
nf_conncount.ko, which was added in kernel 4.16, add it to the kmod.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The nf_socket.ko module was split in commit 8db4c5be88f ("netfilter:
move socket lookup infrastructure to nf_socket_ipv{4,6}.c") into a
common, n IPv4 and an IPv6 part.
The nf_tproxy.ko module was split in commit 45ca4e0cf27 ("netfilter:
Libify xt_TPROXY") into a common, an IPv4 and an IPv6 part.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In kernel commit a0ae2562c6c ("netfilter: conntrack: remove l3proto
abstraction") The modules nf_conntrack_ipv4.ko, nf_conntrack_ipv6.ko and
nf_conntrack.ko were squashed together into one module. This module now
depends on nf_defrag_ipv6 when IPv6 support was activated. This is part
of the main netfilter packages, so add nf_defrag_ipv6.ko also to the
default netfilter packages on kernel 4.19 and later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_OF_NET depends on CONFIG_NVMEM in kernel 4.19. To fix some build
problems in mainline Linux kernel CONFIG_NVMEM was changed from tristate
to bool in commit 2a37ce25d9 ("nvmem: disallow modular CONFIG_NVMEM").
This patch in OpenWrt revert the upstream commit and changes
CONFIG_NVMEM back to tristate we just have to make sure to build this in
for all targets which select CONFIG_OF_NET.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_HW_RANDOM_TPM does not activate a separate kernel module any
more, but it only activates the random code in the tpm.ko.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The video-videobuf2 kernel modules were moved to a new folder in kernel
4.19. videobuf2-v4l2.ko is only available since kernel 4.4, blacklist
this kmod completely on kernel 3.18.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The x86 optimized cryptographic algorithm kernel modules now mostly use
crypto_simd.ko instead of lrw.ko in kernel 4.19. Add the new module to
the kmod-crypto-misc package.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The asn1_decoder.ko module is needed by the kmod-nf-nathelper-extra
package in kernel 4.19, extract it and add the missing dependencies.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Kernel interface changed with kernel 4.19, it does not accept raw GPIO
numbers any more. Deactivate these drivers on kernel 4.19 for now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The r8169 driver uses the phy lib with the realtek phy driver in kernel
4.19 instead of integrating the phy driver into the mac driver.
Add the new phy driver and add this missing dependency.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This makes the patches which were just copied in the previous commit
apply on top of kernel 4.19.
The patches in the backports-4.19 folder were checked if they are really
in kernel 4.19 based on the title and only removed if they were found in
the upstream kernel.
The following additional patches form the pending folder went into
upstream Linux 4.19:
pending-4.19/171-usb-dwc2-Fix-inefficient-copy-of-unaligned-buffers.patch
pending-4.19/190-2-5-e1000e-Fix-wrong-comment-related-to-link-detection.patch
pending-4.19/478-mtd-spi-nor-Add-support-for-XM25QH64A-and-XM25QH128A.patch
pending-4.19/479-mtd-spi-nor-add-eon-en25qh32.patch
pending-4.19/950-tty-serial-exar-generalize-rs485-setup.patch
pending-4.19/340-MIPS-mm-remove-mips_dma_mapping_error.patch
Bigger changes were introduced to the m25p80 spi nor driver, as far as I
saw it in the new code, it now has the functionality provided in this
patch:
pending-4.19/450-mtd-m25p80-allow-fallback-from-spi_flash_read-to-reg.patch
Part of this patch went upstream independent of OpenWrt:
hack-4.19/220-gc_sections.patch
This patch was reworked to match the changes done upstream.
The MIPS DMA API changed a lot, this patch was rewritten to match the
new DMA handling:
pending-4.19/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch
I did bigger manual changes to the following patches and I am not 100% sure if they are all correct:
pending-4.19/0931-w1-gpio-fix-problem-with-platfom-data-in-w1-gpio.patch
pending-4.19/411-mtd-partial_eraseblock_write.patch
pending-4.19/600-netfilter_conntrack_flush.patch
pending-4.19/611-netfilter_match_bypass_default_table.patch
pending-4.19/670-ipv6-allow-rejecting-with-source-address-failed-policy.patch
hack-4.19/211-host_tools_portability.patch
hack-4.19/221-module_exports.patch
hack-4.19/321-powerpc_crtsavres_prereq.patch
hack-4.19/902-debloat_proc.patch
This is based on patchset from Marko Ratkaj <marko.ratkaj@sartura.hr>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This just copies the files from the kernel 4.14 specific folders into
the kernel 4.19 specific folder, no changes are done to the files in
this commit.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The b53 driver was added as a dsa driver into the mainline Linux kernel,
but we still use the swconfig based driver. The header file b53.h is
used by both drivers, but the swconfig one needs an extra member, add
this one in a patch to not overwrite the version shipped with the
mainline kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ledtrig-netdev was added to upstream Linux kernel 4.16, replace our
own version with the patch based on the upstream version.
This will remove the ledtrig-netdev support from kernel 3.18, because I
not want to spend time on backporting it to 3.18. This will make it
easier to use the upstream version with kernel 4.19, by just not
applying this patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
63843750 Update manual pages
27801e98 Bump up version number to 1.35.1
60e020a8 nghttpx: Fix broken trailing slash handling
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The above options were incorrectly changed to required tags. Make them
optional again.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
f6d0e8c36f Fix rwlock stall with PREFER_WRITER_NONRECURSIVE_NP (bug 23861)
2794474c65 powerpc: Add missing CFI register information (bug #23614)
d8ca7a0c71 Fix _dl_profile_fixup data-dependency issue (Bug 23690)
f1e211096b inet/tst-if_index-long: New test case for CVE-2018-19591 [BZ #23927]
4e9f34e54f support: Implement <support/descriptors.h> to track file descriptors
e75481a7a7 support: Close original descriptors in support_capture_subprocess
0f79dc0be3 support_quote_string: Do not use str parameter name
6b2dd53aa0 support: Implement support_quote_string
50477165b9 malloc: Add another test for tcache double free check.
4b246928bd malloc: tcache double free check
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Backport upstream patch fixing incorrect passing of -lxtables to
LDFLAGS instead of LDLIBS in the tc/Makefile
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This updates the backports package used in mac80211 to version 4.19.7-1
which is based on kernel 4.19.7. This integrates all the stable fixes
introduces in this kernel version.
The deleted patches are not needed any more because they are either
included in the upstream Linux kernel 4.19.7 or in backports 4.19.7-1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It's no longer needed as all mt7621 devices use DT binding (supported by
upstream mtd code) for specifying "firmware" part format explicitly.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
