Commit Graph

20192 Commits

Author SHA1 Message Date
Petr Štetiar
795211093f ramips: bdcom-wap2100: Fix boot failure by adding partitions compatible property
Flash partitions were moved under partition table node, but addition of
compatible property was omitted which lead to following boot failure:

 VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
 Please append a correct "root=" boot option; here are the available partitions:
 1f00           16384 mtdblock0
  (driver?)
 Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

Fixes: e4d9217f (ramips: improve BDCOM WAP2100-SK support)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-28 23:37:29 +01:00
Michael Heimpold
e880a30549 mxs: use generic sysinfo board detection
Since we do nothing special for mxs based boards,
we can simply use the generic existing code.
We just need to convert scripts to use the DT
compatible strings.

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
2018-11-28 23:37:29 +01:00
David Yang
824b580079 ramips: fix switch port order for HuaWei HG255D
The order of port marks and LEDs is reversed according to the board.

Signed-off-by: David Yang <mmyangfl@gmail.com>
2018-11-28 01:11:38 +01:00
Roger Pueyo Centelles
cb6a8aa584 ramips: mt7620: add DIR-810L's mt7610e 5 GHz radio
The 5 GHz radio of this device uses an mt7610e pci-e chip, which has
been recently added support.

Tested on the actual device as AP and client, TCP throughput ~90 Mbps
U/D.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2018-11-28 01:11:38 +01:00
Nishant Sharma
df3e0b5806 ramips: add support for UniElec U7621-06-512M-64M variant
Add support for UniElec U7621-06 variant with 512MB RAM and 64MB flash.

Additional specs are below:

CPU: MT7621 (880Mhz)
Bootloader: Ralink U-Boot
Flash: 64MB
 - U-Boot identifies as Macronix MX66L51235F
 - kernel identifies as MX66L51235l (65536 Kbytes)
RAM: 512MB

Rest of the details as per commit 46ab81e405 ("ramips add support for
UniElec U7621-06")

Signed-off-by: Nishant Sharma <nishant@unmukti.in>
[use generic board detection, add firmware partition compatible, extend
firmware partition to use all of the remaining flash space, add a
maximum image size matching the firmware partition size]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-28 01:11:38 +01:00
Mathias Kresin
509d02a3d1 ramips: use generic board detection for Unielec u7621-06
Use the generic board detection for the board instead of the target
specific one. Mark the sysupgrade image compatible with the former used
userspace boardname to allow an upgrade from earlier versions.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-28 00:50:35 +01:00
Thomas Vincent-Cross
a160f50d4f ramips: add support for Wavlink WL-WN570HA1
This commit adds support for the Wavlink WL-WN570HA1, a dual-band PoE
wireless router with the following specifications:

 - CPU: MediaTek MT7688AN 580MHz
 - Flash: 8MB
 - RAM: 64MB
 - Ethernet: 1x 10/100Mbps
 - 2.4 GHz: 802.11b/g/n SoC, 1T1R, 27 dBm
 - 5 GHz: 802.11a/n/ac MT7610E, 1T1R, 25 dBm
 - Antennas: 2x external (1 per radio), detachable
 - LEDs: 3 programmable + Wi-Fi, WAN/LAN, Power
 - Buttons: Reset

Flashing instructions:

Factory U-boot launches a TFTP client if reset button is pressed during power-on.
Rename the sysupgrade file and configure TFTP as follows:

 - Client (WL-WN570HA1) IP: 192.168.10.101
 - Server IP: 192.168.10.100
 - Filename: firmware.bin

Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
[use generic board detection, add firmware partition compatible]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-28 00:50:35 +01:00
Rosy Song
31469aebd4 ath79: add support for ROSINSON WR818 board
This commit adds support for the ROSINSON WR818 WiFi-Router

SoC:    Qualcomm Atheros QCA9563,
FLASH:  Winbond W25Q128FV 16MBytes,
WiFi:   QCA9563 b/g/n 3x3 450Mbit/s,
USB:    1x USB 2.0 Type A, 1x USB2.0 Type C,
IN:     WPS/Reset button GPIO1,
OUT:    Power LED red, Internet LED red, WLAN LED red,
        LAN1 LED red, LAN2 LED red, System LED red,
UART:   RX-GPIO18, TX-GPIO22,

Tested and working:
    - Ethernet (LAN + WAN)
    - WiFi
    - OpenWRT sysupgrade
    - Button
    - LEDs

Installation of OpenWRT from vendor firmware:
    - Connect to the Web-interface at http://192.168.1.1
    - Go to "Administration" -> "Firmware Upgrade"
    - Upload the OpenWrt sysupgrade image

Signed-off-by: Rosy Song <rosysong@rosinson.com>
2018-11-27 21:11:54 +01:00
Mathias Kresin
7574781337 ath79: merge glinet gl-x750 dtsi and dts
The board doesn't come in different flash type flavours, hence there is
no need to keep a dtsi + dts for this purpose.

While at it, fix some whitespace issues.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-27 21:11:54 +01:00
Mathias Kresin
68d77241cd ath79: rename glinet x750
The boardname is gl-x750 and is already used for the led names.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-27 21:11:54 +01:00
Russell Senior
e0def989e8 ramips: fix alphabetic ordering of skylab skw92a
Fix the alphabetic ordering of skylab skw92a in ramips_setup_interfaces.

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-11-27 21:11:54 +01:00
Matthias Badaire
1100ba43db ramips: fix RavPower WD03 SoC dtsi include
The RavPower WD03 is a mt7620n based baord. With the change applied, I2C
should work now with the RavPower WD03.

Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
[reworded commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-27 21:11:54 +01:00
John Crispin
c6aa4f53e8 Revert "x86: add intel microcode entries to grub config"
This reverts commit 546fced2a2.

Signed-off-by: John Crispin <john@phrozen.org>
2018-11-27 18:58:38 +01:00
John Crispin
8ead5a735d Revert "x86: add amd microcode entries to grub config"
This reverts commit a822283c7e.

Signed-off-by: John Crispin <john@phrozen.org>
2018-11-27 18:58:35 +01:00
David Bauer
a734450d6f ath79: add Archer C58/C59 partition compatible
This commit adds firmware partition compatible for the
TP-Link Archer C58 v1 and Archer C59 v1.

Since a22311e this allows to select the correct mtdsplit
parser instead of trying all available ones one by one.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-11-26 21:27:17 +01:00
David Bauer
df2e6b64d1 ath79: add firmware partition compatible for OCEDO
This commit adds firmware partition compatible for the
OCEDO Raccoon and OCEDO Koala.

Since a22311e this allows to select the correct mtdsplit
parser instead of trying all available ones one by one.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-11-26 21:26:56 +01:00
INAGAKI Hiroshi
37c848810c ath79: specify "firmware" partition format for I-O DATA devices
Specify firmware partition format (denx,uimage) by compatible string
for I-O DATA devices.

affected devices (&run tested)

- WN-AC1167DGR
- WN-AC1600DGR2

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-11-26 21:26:07 +01:00
INAGAKI Hiroshi
fa1a120a1a ath79: specify "firmware" partition format for ELECOM WRC-300GHBK2-I
Specify firmware partition format (denx,uimage) by compatible string
for ELECOM WRC-300GHBK2-I.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-11-26 21:26:06 +01:00
Mathias Kresin
f4abc962ec ath79: fix shebang
The shebang was accidentally changed with 9989fd5154 ("ath79: add
support for GL-iNet GL-X750").

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 19:40:31 +01:00
Mathias Kresin
aa82fdf110 ramips: fix GB-PC1/PC2 build error
With ed25e3ac02 ("ramips: fix some clocks in mt7621.dtsi") the
cpuclock node was dropped from the mt7621.dtsi without removing the
references to this node from the GB-PC1/PC2 dts files.

Remove them now, to fix the build error.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 19:40:31 +01:00
Mathias Kresin
d7494f30f5 ramips: fix Lava LR-25G001 invalid led names
It has to be <board>:<colour>:<function> and is expected exactly this
way by the userspace scripts.

While at it, fix some whitespace issues in the dts file and rename the
flash node as required upstream.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 19:40:31 +01:00
Günther Kelleter
33878b0a40 kernel: ar8xxx: get_arl_table now shows all ports of an entry
Multicast ARL entries can have multiple destination ports. Get and dump
all destination ports of each entry, not just the lowest.

Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
2018-11-26 18:41:21 +01:00
Mathias Kresin
be3e69d991 ramips: rt2880: fix pci cells definition
Set the correct number of cells to fix "property has invalid length" dtc
compiler warnings.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 15:54:22 +01:00
Mathias Kresin
e4d9217fe5 ramips: improve BDCOM WAP2100-SK support
Use the generic board detection instead of the target specific one as
all recent additions are doing.

Setup the USB led via devicetree (a58535771f) and include the required
driver by default. Merge the led userspace setting with an existing
identical case.

Use the wps led for boot status indication.

Move the partitions into a partition table node (6031ab345d) and drop
needless labels. Drop misplaced cells properties (53624c1702).

Cleanup the pinmux and only switch pins to gpio functions which a
referenced as gpio in the dts.

Match the maximum image size with the size of the firmware partition.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 15:54:22 +01:00
Mathias Kresin
71ba834cf1 ramips: add Sanlinking Technologies D240 pinmux quirk
The sd function of the nd_sd group configures two of the groups pins as
gpios. The pins are used as PCIe reset/power.

Due to the driver load order, the pins are configured way to late if
triggered by the sd-card driver.

To not introduce another kind of driver load order dependency and
configure the pins as early as possible, means during pinmux driver
load.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 15:54:22 +01:00
Mathias Kresin
d6ce04dad8 ralink: fix mt7620 nd_sd pinmux
In case the nd_sd group is set to the sd-card function, Pins 45 + 46 are
configured as GPIOs. If they are blocked by the sd function, they can't
be used as GPIOs.

Reported-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 15:54:22 +01:00
Mathias Kresin
9ebce69611 ramips: revert fix rt3883 pci pinmux
This reverts commit dcdc6d9dad.

Even if described this way in the datasheet, it causes a bootloop on a
RT-N56U (v1):

  of-flash 1c000000.nor-flash: do_map_probe() failed for type cfi_probe
  of-flash 1c000000.nor-flash: do_map_probe() failed
  VFS: Cannot open root device “(null)” or unknown-block(0,0): error -6

Fixes: FS#1930

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 15:54:22 +01:00
Mathias Kresin
8ec1a66c34 ramips: improve Skylab SKW92A support
Use the generic board detection instead of the target specific one as
all recent additions are doing.

Add the wireless led according the gpio number from the datasheet.
Rename the board part of the leds to match the name used for the
compatible string. Finally, do not hijack the wps led for boot status
indication longer than necessary.

Merge userspace config into existing cases.

Include the manufacture Name in the dts model string.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-11-26 15:54:22 +01:00
John Crispin
749a29f76c Revert "ramips: mt7621-spi: replace the driver with upstream staging one"
This reverts commit a44f000077.

This breaks some mt7621 devices.

Signed-off-by: John Crispin <john@phrozen.org>
2018-11-26 14:43:42 +01:00
Zheng Qian
48a7a2a75d ramips: fix switch ports mapping for newifi d2
Signed-off-by: Zheng Qian <sotux82@gmail.com>
2018-11-26 12:31:19 +01:00
Kevin Schmidt
bce555b09b lantiq: enable FXS ports on VR200v
Disables SMP support.
Add VR200 target to keep SMP on FXS-less device variant.

Signed-off-by: Kevin Schmidt <kevin.patrick.schmidt@googlemail.com>
2018-11-26 12:30:33 +01:00
INAGAKI Hiroshi
879f2ef7c0 ath79: modify mtd partitions for Buffalo BHR-4GRV2
This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and
move it to generic subtarget.

In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs"
partition in the stock firmware. This causes the size of the kernel
to be limited by the fixed value.

0x50000                       0xe80000        0xff0000
  +-------------------------------+--------------+
  |            rootfs             |    kernel    |
  |           (14528k)            |    (1472k)   |
  +-------------------------------+--------------+

After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2
exceeded the limit, and it breaks builds on official buildbot.
Since this issue was also confirmed in ath79, I modified the mtd
partitions to get rid of that limitation.

0x50000                                       0xff0000
  +----------------------------------------------+
  |                   firmware                   |
  |                   (16000k)                   |
  +----------------------------------------------+

However, this commit breaks compatibility with ar71xx firmware, so I
dropped "SUPPORTED_DEVICES += bhr-4grv2".

This commit requires new flash instruction instead of the old one.

Flash instruction using initramfs image:

1. Connect the computer to the LAN port of BHR-4GRV2
2. Set the IP address of the computer to 192.168.12.10
3. Rename the OpenWrt initramfs image to
"bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP
directory
4. Start the tftp server on the computer
5. While holding down the "ECO" button, connect power cable to
BHR-4GRV2 and turn on it
6. Flashing (orange) diag LED and release the finger from the button,
BHR-4GRV2 downloads the intiramfs image from TFTP server and boot
with it
7. On the initramfs image, create "/etc/fw_env.config" file with
following contents
  /dev/mtd1 0x0 0x10000 0x10000
8. Execute following commands to add environment variables for
u-boot
  fw_setenv ipaddr 192.168.12.1
  fw_setenv serverip 192.168.12.10
  fw_setenv ethaddr 00:aa:bb:cc:dd:ee
  fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
9. Perform sysupgrade with squashfs-sysupgrade image
10. Wait ~150 seconds to complete flashing

And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC,
not QCA9558.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-11-26 12:28:17 +01:00
Robert Marko
d6e92b18d9 ath79: Remove source-only flag
Remove the source-only flag from ath79, its supposed to replace ar71xx after next stable release but buildbots are not currently generating images for it.
So in order to expand testing as much as possible and prepare for moving to ath79 lets enable the buildbots to actually build the target.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-11-26 12:24:54 +01:00
Chuanhong Guo
a44f000077 ramips: mt7621-spi: replace the driver with upstream staging one
That driver is more efficient thanks to the refactor of spi reading operation.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2018-11-26 12:24:30 +01:00
Pawel Dembicki
20b09a2125 ramips: add support for Lava LR-25G001
The Lava LR-25G001 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7610EN)
- 5x 10/100/1000 Mbps AR8337 Switch (1 WAN AND 4 LAN)
- 2x external, detachable antennas
- 1x USB 2.0
- UART (J3) header on PCB (57600 8n1)
- 8x LED (3x GPIO-controlled), 2x button
- JBOOT bootloader

Known issues:
- Work only three Gigabit ports (3/5, 1 WAN and 2LAN)

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-11-26 12:16:52 +01:00
Pawel Dembicki
b85fe43ec8 ramips: mt7620: add force use of mdio-mode
Some boards have external switches different than mt7530.

This patch allow to use mdio-mode without 0x1f register.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-11-26 12:16:52 +01:00
Pawel Dembicki
e61812fd34 ar8216: add adjust_link checking
Driver crash when 'phydev->adjust_link' isn't provided.

This patch check if 'phydev->adjust_link' exist before
call the method.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
2018-11-26 12:16:52 +01:00
Weijie Gao
ed25e3ac02 ramips: fix some clocks in mt7621.dtsi
As the cpu clock calculation has been fixed, the clock for gic and spi
should be also fixed.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
Weijie Gao
c7ca224299 ramips: fix cpu clock of mt7621 and add dt clk devices
For a long time the mt7621 uses a fixed cpu clock which causes a problem
if the cpu frequency is not 880MHz.

This patch fixes the cpu clock calculation and adds the cpu/bus clkdev
which will be used in dts.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
Weijie Gao
f5af8be636 ramips: fix register range of memc node in mt7621.dtsi
The memc node from mt7621.dtsi has incorrect register resource.
Fix it according to the programming guide.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
Weijie Gao
e217d69a4a ramips: merge two patches 101-mt7621-timer and 998-mt7621-needs-jiffies
These two patches both modified the mt7621.c, and the patch file
998-mt7621-needs-jiffies.patch adds only one line which is used by the
another patch file. So merge them into one file.

Signed-off-by: Weijie Gao <hackpascal@gmail.com>
2018-11-26 12:13:52 +01:00
INAGAKI Hiroshi
83f08aebb1 ath79: specify "firmware" partition format for Buffalo devices
Specify firmware partition format (denx,uimage) by compatible string
for Buffalo devices.

affected devices (&run tested):
- BHR-4GRV
- WHR-G301N
- WZR-HP-AG300H
- WZR-HP-G302H A1A0
- WZR-HP-G450H (WZR-450HP)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-11-26 12:09:25 +01:00
Tomasz Maciej Nowak
d93b09fa74 sdk: expose part of advanced configuration options
These option can be useful in developement/packagig applications for
OpenWrt. Instead of searching them by hand in Config-build.in lets
expose them for easier access.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-11-26 12:07:06 +01:00
Lorenzo Bianconi
e612e60517 ramips: add mt76x0 node to RT-AC51U device tree
Introduce mt76x0e device tree node in RT-AC51U dts.
Define mt76x0e mtd partition and offset

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
2018-11-26 12:05:47 +01:00
Christian Lamparter
5d5c0b0582 apm821xx: wndr4700: restore sd-card media detection
This was not converted to the new, dt-based board name.

Fixes: e90dc8d272 ("apm821xx: convert to device-tree board detection")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:47 +01:00
Christian Lamparter
a2266a6d42 apm821xx: shuffle helper scripts to the front
In a patch for the ath79, Mathias Kresin mentioned that
helper scripts should be in front of the device targets.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:47 +01:00
Christian Lamparter
d82d84694e apm821xx: add support for the Netgear WNDAP620 and WNDAP660
This patch adds support for the Netgear WNDAP620 and WNDAP660,
they are similar devices, but due to the LAN LED configuration,
the switch setup and WIFI configuration each gets a different
device target.

Hardware Highlights WNDAP620:
CPU: AMCC PowerPC APM82181 at 1000 MHz
DRAM:  128 MB, 2 x 64 MiB DDR2 Hynix H5PS5162GF
CPU: AMCC PowerPC APM82181 at 1000 MHz
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY - Only 1 GBit Port (POE)
Wifi: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 3 internal dual-band antennae + 3 x RSMA for external antennaes

Hardware Highlights WNDAP660:
CPU: AMCC PowerPC APM82181 at 1000 MHz + 2 Heatsinks
DRAM:  256 MB, 2 x 128 MiB DDR2
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY (POE)
Wifi1: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Wifi2: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, 2x dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 6 internal dual-band antennae + 3 x RSMA for external antennaes

Flashing requirements:

 - needs a tftp server at 192.168.1.10/serverip.
 - special 8P8C(aka RJ45)<->D-SUB9 Console Cable
   ("Cisco Console Cable"). Note: Both WNDAP6x0 have
   a MAX3232 transceivers, hence no need for any separate
   CMOS/TTL level shifters.

External Antenna:
The antennae mux is controlled by GPIO 11 and GPIO14. Valid Configurations:
 = Config# = | = GPIO 11 = | = GPIO 14 = |  ===== Description =====
      1.     |   1 / High  |  0 / Low    | Use the internal antennae (default)
      2.     |   0 / Low   |  1 / High   | Use the external antennae

The external antennaes are only meant for the 2.4 GHz band.

One-way Flashing instructions via u-boot:

 0. connect the serial cable to the RJ45 Console Port
    Note: This requires a poper RS232 and not a TTL/USB adaptor.

 1. power up the AP and interrupt the u-boot process at

    'Hit any key to stop autoboot'

 2. setup serverip and ipaddr env settings
    Enter the following commands into the u-boot shell
    # setenv ipaddr 192.168.1.1
    # setenv serverip 192.168.1.10

 3. download the factory.img image to the AP
    Enter the following commands into the u-boot shell

    # tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-squashfs-factory.img

 4. verfiy image integrity
    Enter the following commands into the u-boot shell

    # crc32 $fileaddr $filesize

    If the calculated crc32 checksum does not match, go back to step 3.

 5. flash the image
    Enter the following commands into the u-boot shell

    # nand erase 0x110000 0x1bd0000
    # nand write ${kernel_addr_r} 0x110000 ${filesize}

 6. setup uboot environment
    Enter the following commands into the u-boot shell

    # setenv bootargs
    # setenv fileaddr
    # setenv filesize
    # setenv addroot 'setenv bootargs ${bootargs} root=/dev/ubiblock0_0'
    # setenv owrt_boot 'nboot ${kernel_addr_r} nand0 0x110000; run addroot; run addtty; bootm ${kernel_addr_r}'
    # setenv bootcmd 'run owrt_boot'
    # saveenv

 7. boot
    # run bootcmd

Booting initramfs instructions via u-boot:

 Follow steps 0 - 2 from above.

 3. boot initramfs
    Enter the following commands into the u-boot shell

    # tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin
    # run addtty
    # bootm ${kernel_addr_r}

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:46 +01:00
Christian Lamparter
a9839fe638 generic: rtl8367b: make it possible to specify cpu_port via DT
This patch adds the feature to parse the existing cpu_port DT
property, which is used to specify which port is the cpu port
of the switch.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:46 +01:00
Christian Lamparter
910c2f9e68 generic: rtl836x: support defered probe on mdio-bus
On the WNDAP620, the mdio and mdc lines are controlled by
the EMAC ethernet device. This results in a hen-vs-egg problem.
The rtl8367b driver is probed before the ethernet driver and
the mdio-bus is not available yet, which caused the rtl8367b
driver to fail.

This patch changes the rtl8366_smi_probe_of() function to
return -EPROBE_DEFER if the mdio-bus lookup failed and changes
rtl8366_smi_probe()'s signature to return the error code back to
the callee, so it can propagate back to the kernel. Which, will
retry the switch probe at a later time.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:46 +01:00
Christian Lamparter
fb4bed5fe9 apm821xx: import gpio-export DT code from lantiq
This will come in handy for the Netgear WNDAP620's antennae mux.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:46 +01:00
Christian Lamparter
f6968952df apm821xx: MR24: add to uboot-envtools
This patch adds the complicated u-boot
environment access settings for to the
MR24 target.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-11-26 12:05:46 +01:00
Ram Chandra Jangir
dc6af37544 ipq806x: Add support for IPQ8064 AP161 board
Specification:
   - SoC: Qualcomm Atheros IPQ8064 ARM-v7 Dual Core SMP CPU
   - RAM: 512MB DDR3 System Memory
   - NOR Flash: 32MB SPI NOR
   - NAND Flash: 256MB NAND
   - Ethernet: 5 x 1G via QCA8337N
   - USB: 2 x USB 3.0 SuperSpeed
   - PCIe: 3x Mini PCIe 2.0 Slots
	   Three PCIE2.0 connectors can connect two or three radio cards
           such as the CUS260 for 2.4 GHz WLAN and the CUS239 for 802.11ac WLAN

 How to flash via u-boot console:
   tftpboot 0x44000000 openwrt-ipq806x-qcom_ipq8064-ap161-squashfs-nand-factory.bin
   nand erase  0x1340000 0x4000000
   nand write  0x44000000 0x1340000 $filesize
   setenv bootargs ‘console=ttyMSM0,115200 ubi.mtd=ubi root=/dev/ubiblock0_1’
   saveenv
   bootm

 Further upgrades via sysupgrade.

 Tested on IPQ8064 AP161 Board:
   1) NAND boot
   2) Tested USB and PCIe interfaces
   3) WDOG test
   4) cpu frequency scaling
   5) ethernet, 2G and 5G WiFi
   6) ubi sysupgrade

Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2018-11-26 12:05:46 +01:00
Ram Chandra Jangir
1ade96def7 ipq8064: pinctrl: Fixed missing RGMII pincontrol definitions
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
2018-11-26 12:05:46 +01:00
Sergey Ryazanov
8baad26d01 ar71xx: fix RouterBOARD Power LED default state
RouterBOARD(s) bootloader actully turns Power LED off just before
it starts the kernel. So we need to set the LED default status to On
instead of Keep in order to keep LED on during kernel boot.

This change fixes Power LED off during the kernel boot on the RB91x and
SXT Lite boards.

Fixes: 6cad8ee0bd ("ar71xx: keep the RouterBOARD Power LED in On state")

CC: Mathias Kresin <dev@kresin.me>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
2018-11-26 12:05:45 +01:00
Ben Greear
38167cb7f4 hotplug: Allow configuring radio name.
This way the radio (phy) name can be the same through module reloads.

To set the desired name:

uci set wireless.@wifi-device[0].phyname=wiphy0

I guess this only works on ipq6086 boards as I could not find a more
generic place to put this.  Maybe someone can improve it.

Signed-off-by: Ben Greear <greearb@candelatech.com>
2018-11-26 12:05:45 +01:00
Tomasz Maciej Nowak
a822283c7e x86: add amd microcode entries to grub config
Create initrd enries for x86 images, that'll load amd microcode as early
as possible. Also remove the preinit script responsible for late load of
microcode.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-11-26 12:05:45 +01:00
David Bauer
946ffe470d ath79: add support for Archer C58/C59 v1
This commit adds support for the Archer C58 v1 and C59 v1, previously
supported in the ar71xx target.

CPU:   Qualcomm QCA9561
RAM:   64M (C58) / 128M (C59)
FLASH: 8M (C58) / 16M (C59)
WiFi:  QCA9561 bgn 3x3:3
       QCA9888 nac 2x2:2
LED:   Power, WiFi 2.4, WiFi 5, WAN green, WAN amber, LAN, WPS
       Only C59: USB
BTN:   WPS, WiFi, Reset

Installation
------------

Via Web-UI:
Update factory image via Web-UI.

Via TFTP:
Rename factory image to "tp_recovery.bin" and place it in the root-dir
of your tftp server. Configure to listen on 192.168.0.66. Power up the
router while holding down the reset-button. The router will flash itself
and reboot.

Note: For TFTP, you might need a switch between router and computer, as
link establishment might take to long.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-11-26 12:05:45 +01:00
Daniel Santos
89eb1a6d72 ralink: Add support for GPIO as interrupt-controller
The gpio-ralink driver has everything it needs to be used as an
interrupt controller except for device tree support.  This simple patch
adds that support by configuring the irq domain to use two cells and
adding the appropriate documentation to the devicetree bindings.

Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
2018-11-26 12:05:45 +01:00
Luo chongjun
9989fd5154 ath79: add support for GL-iNet GL-X750
this patch adds supports for GL-X750.

Specification:
- SOC: QCA9531 (650MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 10/100: 1xLAN + 10/100: 1xWAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Button: 1x reset button
- LED: 5x LEDS (green)

Flash instruction:
The original firmware is openwrt, so both LuCI or sysupgrade can be used.

Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
2018-11-26 12:05:45 +01:00
Christoph Krapp
987b961537 ar71xx: add support for UniFi-AC-Mesh-Pro
This adds the build option for UniFi AC Mesh Pro as well as
model detection for it.
The device is a hardware clone of the AC Pro.

- SoC: QCA9563-AL3A (775Mhz)
- RAM: 128MiB
- Flash: 16MiB - dual firmware partitions!
- LAN: 2x 1000M - POE+
- Wireless:
        2.4G: QCA9563
          5G: UniFi Chip, QCA988X compatible

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2018-11-26 12:05:44 +01:00
Petr Štetiar
16b950c981 ramips: Add support for ZTE ZXECS EBG3130 aka BDCOM WAP2100-SK
On the bottom sticker it's branded as ZTE ZXECS EBG3130 device, but in factory
OpenWrt image it's referenced as BDCOM WAP2100-SK device.

Specifications:

- SoC: MediaTek MT7620A
- RAM: 128 MB
- Flash: 16 MB
- Ethernet: 5 FE ports
- Wireless radio: 2T2R 2.4 GHz and 1T1R 5 GHz (MT7610EN, unsupported)
- UART: 1 x UART on PCB marked as J2 (R=RX, T=TX, G=GND) with 115200 8N1 config
- LEDs: Power, FE ports 1-5, WPS, USB, RF 2.4G, RF 5G
- Other: USB port, SD card slot and 2x external antennas (non-detachable)

Flashing instructions:

A) The U-Boot has HTTP based firmware upgrade

  A1) Flashing notes

  We've identified so far two different batches of units, unfortunately
  each batch has different U-Boot bootloader flashed with different
  default environment variables, thus each batch has different IP address
  for accessing web based firmware updater.

  * First batch has web based bootloader IP address 1.1.1.1
  * Second batch has web based bootloader IP address 192.168.1.250

  In case you can't connect to either of those IPs, you can try to get
  the default IP address via two methods:

  A1.1) Serial console, then the IP address is visible during the boot

   ...
   HTTP server is starting at IP: 1.1.1.1
   raspi_read: from:40004 len:6
   HTTP server is ready!
   ...

  A1.2) Over telnet/SSH using this command:

   root@bdcom:/# grep ipaddr= /dev/mtd0
   ipaddr=1.1.1.1

  A2) Flashing with browser

  * Change IP address of PC to 1.1.1.2 with 255.255.255.0 netmask
  * Reboot the device and try to reach web based bootloader in the
    browser with the following URL http://1.1.1.1

  * Quickly select the firmware sysupgrade file and click on the
    `Update firmware` button, this all has to be done within 10 seconds,
    bootloader doesn't wait any longer

   If done correctly, the web page should show UPDATE IN PROGRESS page
   with progress indicator. Once the flashing completes (it takes roughly
   around 1 minute), the device will reboot to the OpenWrt firmware

  A3) Flashing with curl

   sudo ip addr add 1.1.1.2/24 dev eth0
   curl \
      --verbose \
      --retry 3 \
      --retry-delay 1 \
      --retry-max-time 30 \
      --connect-timeout 30 \
      --form "firmware=@openwrt-ramips-mt7620-BDCOM-WAP2100-SK-squashfs-sysupgrade.bin" \
      http://1.1.1.1

   Now power on the router.

B) The U-boot is based on Ralink SDK so we can flash the firmware using UART.

   1. Configure PC with a static IP address and setup an TFTP server.
   2. Put the firmware into the tftp directory.
   3. Connect the UART line as described on the PCB (G=GND, R=RX, T=TX)
   4. Power up the device and press 2, follow the instruction to set device and
      tftp server IP address and input the firmware file name. U-boot will then load
      the firmware and write it into the flash.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-26 12:05:44 +01:00
Tomasz Maciej Nowak
546fced2a2 x86: add intel microcode entries to grub config
Create initrd enries for x86 images, that'll load intel microcode as
early as possible. To achieve that the test module for grub is enabled
which provides shell-like conditionals. Also restrict the late load of
microcode to AMD processors.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-11-26 12:05:44 +01:00
Tomasz Maciej Nowak
51e199fbe8 x86: add packages files to image bootfs
Add files to bootfs image from selected as built-in packages, which want
to install files to targets boot file system.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-11-26 12:05:44 +01:00
Tomasz Maciej Nowak
f78b261637 x86: mount writable bootfs
Mount boot file system with rw option to allow installation of packages
which install files to /boot directory.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2018-11-26 12:05:44 +01:00
Petr Štetiar
d42a7c4699 ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method
Ubiquity allows flashing of unsigned factory images via TFTP recovery
method[1]. They claim in airOS v6.0.7 release changelog[2] following:

 All future airOS versions will be signed in this way and not allow
 unsigned firmware to be loaded except via TFTP.

U-boot bootloader on M-XW devices expects factory image revision
version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
(May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
number is actually a number, but in currently generated images there's
OpenWrt text and so the check fails:

 Hit any key to stop autoboot:  0
 Setting default IP 192.168.1.20
 Starting TFTP server...
 Receiving file from 192.168.1.25:38438
 Received 4981148 bytes
 Firmware check failed! (1)

By placing arbitrary correct number first in major version, we make the
bootloader happy and we can flash factory images over TFTP again:

 Received 3735964 bytes
 Firmware Version: XW.ar934x.v6.0.4-42.r8474-56aa1ac-OpenWrt
 Setting U-Boot environment variables
 Un-Protected 1 sectors
 Erasing Flash.... done

Patch provided by AREDN[3] project, tested on Bullet M2 XW (ynezz) and
Nanostation M5 XW (ae6xe).

1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points
2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt
3. https://github.com/aredn

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-26 12:05:44 +01:00
Petr Štetiar
db4b6535f8 ath79: Add support for Ubiquity Bullet M (XW)
CPU: AR9342 SoC
RAM:     64 MB DDR2
Flash:    8 MB NOR SPI
Ports:  100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART:     1 UART on PCB marked as J1 with 115200 8N1 config
LEDs:       Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons:    Reset

UART connection details

  .---------------------------------.
  |                                 |
[ETH]          J1                 [ANT]
  |    o VCC o RX o TX o GND        |
  `---------------------------------'

Flashing instructions

 A) Serial console, U-Boot and TFTP

   1. Connect to serial header J1 on the PCB
   2. Power on device and enter U-Boot console
   3. Set up TFTP server serving an OpenWrt initramfs build
   4. Load initramfs build using the command tftpboot in the U-Boot cli
   5. Boot the loaded image using the command bootm
   6. Copy squashfs OpenWrt sysupgrade build to the booted device
   7. Use mtd to write sysupgrade to partition "firmware"
   8. Reboot and enjoy

 B) Experimental factory image flashing over SSH from airOS v6.1.7

   1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware
      no other airOS version is currently supported
   2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing
   3. cd ubnt-bullet-m2hp-openwrt-flashing
   4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin

Tested only on Bullet M2HP.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-26 12:05:38 +01:00
Roman Yeryomin
ae2b43b873 ramips: fix ethernet for f5d8235-v2 board
Belkin F5D8235 v2 has two ethernet switches on board.
One internal rt3052 and rtl8366rb on rgmii interface.
Looks like internal switch settings were lost in
translation to device tree infrastructure.

Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-11-26 09:58:17 +01:00
Russell Senior
e42327aa89 ramips: add support for Skylab SKW92A in EVB
Specifically, SKW92A_E16, described here:

  http://www.skylabmodule.com/wp-content/uploads/SkyLab_SKW92A_V1.04_datasheet.pdf

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x u.FL
- Power by micro-USB connector at USB1 on EVB
- UART via micro-USB connector at USB3 on EVB (57600 8n1)
- 5x Ethernet LEDs
- 1x WLAN LEDs
- 1x WPS LED connected by jumper wire from I2S_CK on J20 to WPS_LED pin hole next
  to daughter board on EVB
- WPS/Reset button (S2 on EVB)
- RESET button (S1 on EVB) is *not* connected to RST hole next to daughter board

Flash instruction:

>From Skylab firmware:

1. Associate with SKYLAP_AP
2. In a browser, load: http://10.10.10.254/
3. Username/password: admin/admin
4. In web admin interface: Administration / Upload Firmware, browse to
   sysupgrade image, apply, flash will fail with a message:
   Not a valid firmware. *** Warning: "/var/tmpFW" has corrupted data!
5. Telnet to 10.10.10.254, drops you into a root shell with no credentials
6. # cd /var
7. # mtd_write -r write tmpFW mtd4
   Unlocking mtd4 ...
   Writing from tmpFW to mtd4 ... [e]
8. When flash has completed, you will have booted into your firmware.

>From U-boot via TFTP and initramfs:

1. Place openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin on a TFTP server
2. Connect to serial console at USB3 on EVB
3. Connect ethernet between port 1 (not WAN) and your TFTP server (e.g.
   192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "1"
7. At u-boot prompts:
   Input device IP (10.10.10.123) ==:192.168.11.21
   Input server IP (10.10.10.3) ==:192.168.11.20
   Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin
8. Move ethernet to port 0 (WAN) on EVB
9. At new OpenWrt console shell, fetch squashfs-sysupgrade image and flash
   with sysupgrade.

>From U-boot via TFTP direct flash:

1. Place openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin on a TFTP server
2. Connect to serial console at USB3 on EVB (57600 8N1)
3. Connect ethernet between port 1 (not WAN) an your TFTP server (e.g.
   192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "2"
7. At u-boot prompts:
   Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
   Input device IP (10.10.10.123) ==:192.168.11.21
   Input server IP (10.10.10.3) ==:192.168.11.20
   Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin
8. When transfer is complete or as OpenWrt begins booting, move ethernet to
   port 0 (WAN).

Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-11-26 09:47:27 +01:00
Roman Yeryomin
b0d6653ab8 rb532: drop 4.9 support
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-11-26 09:34:09 +01:00
Roman Yeryomin
9f13cde1fa rb532: switch to 4.14
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-11-26 09:33:01 +01:00
Roman Yeryomin
920845357f rb532: add 4.14 support
Signed-off-by: Roman Yeryomin <roman@advem.lv>
2018-11-26 09:31:50 +01:00
Martin Schiller
18398abe1e lantiq/basefiles: use shutdown instead of stop when the system goes down
I can't see any reason why we shouldn't use shutdown for lantiq as well.

Signed-off-by: Martin Schiller <ms@dev.tdt.de>
2018-11-25 19:26:55 +01:00
Petr Štetiar
82b34c1f60 imx6: image: ventana: Add missing BOOT_SCRIPT variable
This is probably theoretical problem as the Ventana is defined first in
the image Makefile, but once the position of the definition would change
in the future (alphabetical sorting?) it would get bootscript from the
previous board which would have BOOT_SCRIPT set.

Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2018-11-25 19:23:03 +01:00
Daniel Golle
7c4251d881 ramips: select kmod-mt76x0e for TP-Link ArcherC20i and wr902ac-v3
Both devices come with a MediaTek MT7610E 5GHz 802.11ac 1T1R radio
which wasn't supported at the time the devices were added to OpenWrt.
Now that we got it, include kmod-mt76x0e in images for those devices.

Reported-by: Arian Sanusi <openwrt@semioptimal.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-11-25 15:24:49 +01:00
Daniel Golle
51c094e703 kernel: enable CONFIG_BRIDGE_VLAN_FILTERING
This allows us to use the bridge as a managed switch and gracefully
handle mixed tagged and untagged frames. Prior to this, the only
alternative was creating one bridge per vlan which quickly becomes a
nightmare and still won't let you mix both tagged and untagged frames on
the physical port without some complex ebtables magic.

This is in line with the notion that OpenWRT is the network go-to swiss
army knife when you need a nice set-and-forget, low maintenance box to
handle a specific task.

Current builds of the ip-bridge package already fully support this
feature so the only requirement is enabling the kernel config.

This is disabled by default so existing bridge configurations will not
be affected.  This patch only gives the ability to turn it on with an
'ip link' command.  If there is interest, I could look into making the
feature accessible via uci configuration.

It causes about 3.1% hit on raw bridging speed, which is relatively
trivial considering that I had to use 300 byte packets to strain the CPU
enough to notice a slowdown at all.  The ER8 would chug along at wire
speed otherwise, and that's using only one core.  Since the typical
bridge use case on OpenWRT is wireless, I doubt it would be noticeable
at all.

With BRIDGE_VLAN_FILTERING

iperf -u -c 192.168.1.105 -b 1G -l 300
------------------------------------------------------------
Client connecting to 192.168.1.105, UDP port 5001
Sending 300 byte datagrams, IPG target: 2.24 us (kalman adjust)
UDP buffer size:  208 KByte (default)
------------------------------------------------------------
[  3] local 192.168.1.12 port 58045 connected with 192.168.1.105 port 5001
[ ID] Interval       Transfer     Bandwidth
[  3]  0.0-10.0 sec   977 MBytes   820 Mbits/sec
[  3] Sent 3414986 datagrams
[  3] Server Report:
[  3]  0.0-10.0 sec   811 MBytes   680 Mbits/sec   0.000 ms
581210/3414986 (0%)

Without BRIDGE_VLAN_FILTERING

iperf -u -c 192.168.1.105 -b 1G -l 300
------------------------------------------------------------
Client connecting to 192.168.1.105, UDP port 5001
Sending 300 byte datagrams, IPG target: 2.24 us (kalman adjust)
UDP buffer size:  208 KByte (default)
------------------------------------------------------------
[  3] local 192.168.1.12 port 36645 connected with 192.168.1.105 port 5001
[ ID] Interval       Transfer     Bandwidth
[  3]  0.0-10.0 sec   977 MBytes   820 Mbits/sec
[  3] Sent 3414990 datagrams
[  3] Server Report:
[  3]  0.0-10.0 sec   836 MBytes   701 Mbits/sec   0.000 ms
493950/3414990 (0%)

In terms of kernel size, it uses 16KB (6753K vs 6737K on ER8) so a
0.002% hit.  The exact 16KB is probably just due to how the kernel is
compressed.

Suggested-by: Jonathan Thibault <jonathan@navigue.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2018-11-25 15:24:49 +01:00
Rafał Miłecki
18c5e7ba91 ath79: specify "firmware" partition format for Ubiquiti UniFi
This affects:
1. Ubiquiti UniFi-AC-LITE/LR
2. Ubiquiti UniFi-AC-PRO
3. Ubiquiti UniFi-AC-MESH
4. Ubiquiti UniFi-AC-MESH PRO

Succesfully tested on UniFi AP AC Pro.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-24 19:04:29 +01:00
Hannu Nyman
3e19113d5d ath79: specify "firmware" partition format for WNDR3700 and v2
Specify the new "firmware" partition format for Netgear WNDR3700
and WNDR3700v2 similarly as ffd082aa did for WNDR3800, the third
device in the family.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2018-11-24 13:15:55 +01:00
Rafał Miłecki
c8a005fefd ath79: specify "firmware" partition format for TP-LINK Archer C7 v2
With this change it doesn't require trying parsers one by one.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-24 12:46:00 +01:00
Rafał Miłecki
c87d47aee8 kernel: drop unused arch_split_mtd_part()
No single target/arch uses it and most likely there is no need to make
such a potential code target/arch specific.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-24 12:24:02 +01:00
Rafał Miłecki
f995e143ba kernel: add missing version.h include to the TP-LINK parser
Fixes: a29c8d685b ("kernel: add DT binding support to the TP-LINK parser")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-24 11:48:47 +01:00
Rafał Miłecki
a29c8d685b kernel: add DT binding support to the TP-LINK parser
It allows triggering it directly by specifying format in the DT.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-24 09:56:53 +01:00
Rafał Miłecki
ffd082aa38 ath79: specify "firmware" partition format for Netgear WNDR3800
It doesn't require trying parsers one by one.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-24 08:46:59 +01:00
Rafał Miłecki
a22311e6a6 kernel: add DT binding support to the uimage parsers
It allows specifying default and Netgear parsers directly in the DT.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-24 08:31:56 +01:00
Rafał Miłecki
934edb764d kernel: don't auto-split "firmware" if it has "compatible" DT property
If "compatible" is being used that should trigger a proper parser
directly. It's more reliable thanks to not trying parsers one by one. In
such case partition shouldn't be split automatically to avoid parsing it
twice.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-24 08:31:55 +01:00
David Bauer
6680fab947 kernel: b53: register switch on probe
Currently, the b53 MDIO switch driver registers the switch on
config-init and not on device probe. Because of this, the switch
gets added every time the associated interface comes up.

This commit fixes this behavior by registering the switch on device
probe.

Compile- and run-tested on OCEDO Koala.

Signed-off-by: David Bauer <mail@david-bauer.net>
2018-11-23 21:45:51 +00:00
Koen Vandeputte
3a1978bbb4 kernel: bump 3.18 to 3.18.126
Refreshed all patches.

Compile-tested: adm5120
Runtime-tested: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-22 12:40:19 +01:00
Koen Vandeputte
02e16e9e82 kernel: bump 4.14 to 4.14.82
Refreshed all patches.

Compile-tested: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested: ar71xx, cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-11-22 10:49:01 +01:00
Koen Vandeputte
e1debc557c kernel: bump 4.9 to 4.9.138
Refreshed all patches.

Compile-tested: ar71xx, layerscape
Runtime-tested: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-22 10:49:01 +01:00
Rafał Miłecki
d3381b5a64 bcm53xx: request Seama parser on DIR-885L directly
It's more reliable as mtd subsystem doesn't have to blindly try that
parser. It allows disabling MTD_SPLIT_FIRMWARE completely (TRX is
handled in a similar way).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-22 10:13:56 +01:00
Rafał Miłecki
dab5a93086 kernel: add DT binding support to the Seama parser
It allows specifying that parser directly in the DT.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-22 10:13:56 +01:00
Rafał Miłecki
4585cd3bdf kernel: move diff adding run_parsers_by_type() between mtd patches
It makes more sense to add run_parsers_by_type() in a patch that
introduces parser types. That makes the other one just add a code using
it.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-20 14:44:01 +01:00
Rafał Miłecki
4d0431801d kernel: don't export parse_mtd_partitions_by_type() in 4.9 and 4.14
That function isn't used anywhere out of the mtdpart.c & can be static.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-20 14:44:01 +01:00
Rafał Miłecki
9b8a955358 kernel: drop mtd_pad_erasesize() helper from 4.9 and 4.14
It has been last used in kernel 3.18 for uimage and squashfs splitters
embedded in the mtdpart.c.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-19 13:33:05 +01:00
Rinki Kumari
dd02a19ff5
ar71xx: fix TP-Link Archer C7 v5 switch LEDs
Signed-off-by: Rinki Kumari <rinki13@gmail.com>
2018-11-17 16:27:38 +01:00
Pau Escrich
15f16bf05b ar71xx: add support for Gainstrong MiniBox V3.2
Adds MiniBox V3.2 ar71xx target (QCA99531 + QCA9887)
Info: http://oolite.cn/minibox-v3-2-qca9531-qca9887-module-pin-specification.html
Reference patch: http://oolite.cn/wp-content/uploads/2017/09/minibox_v3_cc15.05_20160325.patch
Installation: Upload firmware to uboot via HTTP at 192.168.1.1 (press button for 5 seconds)

Signed-off-by: Pau Escrich <p4u@dabax.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(daniel@makrotopia.org: rebased and fixed conflicts, fixed LED name,
                        added ath10k eeprom)
2018-11-15 19:49:51 +01:00
Rafał Miłecki
c6a1bcac16 kernel: fix ubifs loosing O_TMPFILE data after power cut
There was a bug in ubifs related to the O_TMPFILE. When reapplying
changes after power cut data could be lost. This problem was exposed by
overlayfs and the upstream commit 3a1e819b4e80 ("ovl: store file handle
of lower inode on copy up").

This fixes a regression introduced when switching from 4.9 to 4.14.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2018-11-15 12:32:20 +01:00
Koen Vandeputte
e14dc93073 kernel: bump 4.14 to 4.14.81
Refreshed all patches.

Removed upstreamed patches:
- 081-spi-bcm-qspi-switch-back-to-reading-flash-using-smal.patch

Altered patches:
- 0054-cpufreq-dt-Handle-OPP-voltage-adjust-events

Compile-tested on: cns3xxx, imx6, ipq806x, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-14 16:27:43 +01:00
Koen Vandeputte
7e20e4ab96 kernel: bump 4.9 to 4.9.137
Refreshed all patches.

Removed upstreamed hunks in:
- 703-phy-support-layerscape.patch

Compile-tested on: ar71xx, layerscape
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-14 16:27:43 +01:00
Koen Vandeputte
f7a406deaf kernel: bump 3.18 to 3.18.125
Refreshed all patches.

Compile-tested on: adm5120
Compile-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2018-11-14 16:27:43 +01:00
Stijn Tintel
e95e9fcbb2 kernel: bump 4.14 to 4.14.80
Refresh patches.

Compile-tested: ar71xx, ath79, x86/64
Runtime-tested: ar71xx, ath79, x86/64

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2018-11-13 00:44:01 +02:00