Commit Graph

20588 Commits

Author SHA1 Message Date
Christian Lamparter
324e94f31b mpc85xx: disable bricking TL-WDR4900v1 images
The current mpc85xx build is failing because the
TL-WDR4900v1 kernel image no longer fits into the
partition. Extending the kernel is not possible
without updating u-boot's kernel loader commands.

This patch disables the WDR4900v1 until the kernel
image size issue is fixed so the buildbot can still
compile the Sophos RED 15w Rev.1 . Installing the
WDR4900v1 images would cause the routers to get
bricked.

For the discussion, please go to:
<https://github.com/openwrt/openwrt/pull/1773>

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-04-15 00:20:56 +02:00
Petr Štetiar
78ee6b1a40 kernel: MIPS: perf: ath79: Fix perfcount IRQ assignment
Currently it's not possible to use perf on ath79 due to genirq flags
mismatch happening on static virtual IRQ 13 which is used for
performance counters hardware IRQ 5.

On TP-Link Archer C7v5:

           CPU0
  2:          0      MIPS   2  ath9k
  4:        318      MIPS   4  19000000.eth
  7:      55034      MIPS   7  timer
  8:       1236      MISC   3  ttyS0
 12:          0      INTC   1  ehci_hcd:usb1
 13:          0  gpio-ath79   2  keys
 14:          0  gpio-ath79   5  keys
 15:         31  AR724X PCI    1  ath10k_pci

 $ perf top
 genirq: Flags mismatch irq 13. 00014c83 (mips_perf_pmu) vs. 00002003 (keys)

On TP-Link Archer C7v4:

         CPU0
  4:          0      MIPS   4  19000000.eth
  5:       7135      MIPS   5  1a000000.eth
  7:      98379      MIPS   7  timer
  8:         30      MISC   3  ttyS0
 12:      90028      INTC   0  ath9k
 13:       5520      INTC   1  ehci_hcd:usb1
 14:       4623      INTC   2  ehci_hcd:usb2
 15:      32844  AR724X PCI    1  ath10k_pci
 16:          0  gpio-ath79  16  keys
 23:          0  gpio-ath79  23  keys

 $ perf top
 genirq: Flags mismatch irq 13. 00014c80 (mips_perf_pmu) vs. 00000080 (ehci_hcd:usb1)

This problem is happening, because currently statically assigned virtual
IRQ 13 for performance counters is not claimed during the initialization
of MIPS PMU during the bootup, so the IRQ subsystem doesn't know, that
this interrupt isn't available for further use.

So this patch fixes the issue by simply booking hardware IRQ 5 for MIPS PMU.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-15 00:01:57 +02:00
Petr Štetiar
5c8f557b36 Revert "ath79: Add WPS button to TP-Link Archer C7v5"
Reverting this commit as I've missed the fact, that the button is
already present in the included DTSI file.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-14 23:42:03 +02:00
Eike Feldmann
9e0fb5a27f ramips: add support for Rakwireless RAK633
It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or
Vocore2.

Specification:

CPU:       MT7628 580 MHz. MIPS 24K
RAM:       64 MB
Flash:     8 MB
WIFI:      802.11n/g/b 20/40 MHz
USB:       1x Port USB 2.0
Ethernet:  5 Port ethernet switch
UART:      2x

Installation: Use the installed uboot Bootloader. Connect a serial cable
to serialport 0. Turn power on.  Choose the option: "Load system code
then write to Flash via TFTP".  Choose the local device IP and the TFTP
server IP and the file name of the system image.  After if the
Bootloader will copy the image to the local flash.

Notes: The I2C Kernel module work not correctly. You can send and
receive data. But the command i2cdetect doesn’t work. FS#845

Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com>
[commit subject and message touches, DTS whitespace fixes, wifi LED
rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses,
removed i2c kernel modules]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-14 23:42:03 +02:00
David Bauer
43e8c37cb4 ramips: add support for GL.iNet VIXMINI
Hardware
--------
SoC:   MediaTek MT7628NN
RAM:   64M DDR2 (Etron EM68B16CWQD-25H)
FLASH: 8M (Winbond W25Q64JVSIQ)
LED:   Power - WLAN
BTN:   Reset
UART:  115200 8N1
       TX and RX are labled on the board as pads next to the SoC

Installation via web-interface
------------------------------
1. Visit the web-interface at 192.168.8.1
   Note: The ethernet port is by default WAN. So you need to connect to
   the router via WiFi

2. Navigate to the Update tab on the left side.

3. Select "Local Update"

4. Upload the OpenWrt sysupgrade image.
   Note: Make sure you select not to preserve the configuration.

Installation via U-Boot
-----------------------
1. Hold down the reset button while powering on the device.
   Wait for the LED to flash 5 times.

2. Assign yourself a static IPv4 in 192.168.1.0/24

3. Upload the OpenWrt sysupgrade image at 192.168.1.1.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-13 18:46:40 +02:00
Pawel Dembicki
b3f7a73860 mpc85xx: generic: Check kernel size for the TL-WDR4900
TP-Link TL-WDR 4900 have u-boot with read-only env.
Boot command read only 0x29F000 data from flash.
Bigger images causes crc error. It can't be changed.

This patch add kernel size checking.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [utilize KERNEL_SIZE]
2019-04-13 18:46:40 +02:00
David Bauer
bb831ca43a mpc85xx: clean up device package selection
Remove wireless and USB packages from the device-specific package
selection as they are already selected by the target itself.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-13 15:09:09 +02:00
David Bauer
84b1257f80 mpc85xx: remove USB support from kernel
This removes USB support from the compiled kernel. Because of this, the
kernel is just small enough for the TP-Link WDR4900 to boot the
resulting kernel.

This is necessary to support the WDR4900 in the upcoming 19.xx release.
In the long run, this should be fixed with a second stage bootloader, as
the vendor bootloader only loads the first 2684k bytes.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-13 15:09:09 +02:00
INAGAKI Hiroshi
3fd443640c ath79: remove unnecessary packages from I-O DATA ETG3-R
I-O DATA ETG3-R is a wired router. So wireless-related packages are
unnecessary and remove those packages from default configuration to
reduce flash usage.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2019-04-13 15:06:36 +02:00
Sven Roederer
e0d98e120a ath79: add TP-Link WR842N v3
This adds support for the TP-Link WR842N v3 which is already supported on ar71xx
target (0b45bec22c).

Specification:
* SoC: QCA9533 ver 2 rev 0
* 16 MB Flash (gd25q128)
* 64 MB RAM
* 1 WAN 10/100 MBit/s (blue connector)
* 4 LAN 10/100 MBit/s (AR8229; 4 ports; yellow connectors)
* Atheros AR9531 (2,4GHz, two fixed antennas)
* USB
* Reset / WPS button
* WiFi button (rf kill)
* 8 green leds; 1 red/green led
* serial console (115200 8N1, according to the OpenWrt-wiki some soldering is needed)

Installation:
* flash via vendor WebUI (the filename must not exceed certain length)
* sysupgrade from installed OpenWrt (also ar71xx)

Thanks to Holger Drefs for providing the hardware

Tested-by: @kofec (github)
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
2019-04-13 14:39:59 +02:00
Daniel Golle
66e2acad9c ramips: fix pinctrl to allow hardware i2c on WRTNODE2R
Instead of assigning I2C pins as GPIOs by default, leave it up to the
user whether to install kmod-i2c-mt7621 and use them for hardware I2C
instead.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-04-11 22:26:28 +02:00
Daniel Golle
b6acb7b718 kernel: move and replace accepted patch
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2019-04-11 19:21:55 +02:00
Koen Vandeputte
fa8d5ad21b imx6: bump sdma firmware to 3.4
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-09 11:29:20 +02:00
Daniel Gimpelevich
f61e754522 ath79: add support for Netgear EX6400 and EX7300
This is sold as a dual-band 802.11ac range extender. It has a sliding
switch for Extender mode or Access Point mode, a WPS button, a recessed
Reset button, a hard-power button, and a multitude of LED's, some
multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is
Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may
connect at 115200 bps, 8 data bits, no parity, 1 stop bit.

Specification:
- System-On-Chip: QCA9558
- CPU/Speed: 720 MHz
- Flash-Chip: Winbond 25Q128FVSG
- Flash size: 16 MiB
- RAM: 128 MiB
- Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3
- Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4
- PHY: Atheros AR8035-A

Installation:
If you can get to the stock firmware's firmware upgrade option, just feed
it the factory.img and boot as usual. As an alternative, TFTP the
factory.img to the bootloader.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[whitespace fix in DTS and reorder of make variables]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-09 11:09:26 +02:00
Daniel Gimpelevich
d75d4837fc ath79: remove more duplicate image build variables
Remove Netgear-specific image build variables which are set to the same
value.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[reordering of variables, removed stray newline]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-09 11:09:26 +02:00
Hauke Mehrtens
1f839c8584 sunxi: Remove already applied patch
This patch is already included in kernel v4.19.31.

Fixes: 8df12d76c6 ("kernel: bump 4.19 to 4.19.34")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-04-08 20:34:27 +02:00
Adrian Schmutzler
93d23aced2 ar71xx: Correct MAC address for WAN interface of Archer C7 v5
This device shares the network config with v4, thus the WAN MAC
also needs to be fixed the same way. However, the partition
where the MAC address resides has been changed.

Based on: https://github.com/openwrt/openwrt/pull/1726

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-08 18:37:05 +02:00
Adrian Schmutzler
9aa8f87d27 ar71xx: Add "info" partition for TP-Link Archer C7 v5
This adds the "info" MTD partition, as it is specified in the
ath79 DTS:
https://github.com/openwrt/openwrt/blob/master/target/linux/ath79/dts/qca9563_tplink_archer-c7-v5.dts#L35

This is required to set the WAN MAC address, as it is build based
on the LAN MAC address, which in turn has to be read from the
"info" partition:
https://github.com/openwrt/openwrt/blob/master/target/linux/ath79/dts/qca9563_tplink_archer-c7-v5.dts#L35

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-08 18:37:04 +02:00
Petr Štetiar
02556d6365 ath79: Add WPS button to TP-Link Archer C7v5
This patch adds currently missing support for the WPS button on TP-Link
Archer C7v5.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Adrian Schmutzler
0a13f589c3 ath79: Correct MAC address for WAN interface of Archer A7/C7 v5
These devices share the network config with C7v4, thus the WAN MAC
also needs to be fixed the same way. However, the partition
where the MAC address resides has been changed.

Based on: https://github.com/openwrt/openwrt/pull/1726

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-08 18:37:04 +02:00
Adrian Schmutzler
a5885ea407 ath79: Fix GPIO reset button on TP-Link Archer C7v5
The GPIO for the reset button for the Archer C7v5 changed from
ar71xx to ath79. An investigation based on tests revealed
that the A7v5 responds on "11", while the C7v5 responds on
"5" as set for ar71xx.

Thus, we just define this in the DTS files instead of in the
common DTSI.

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-08 18:37:04 +02:00
Adrian Schmutzler
6f354c4d32 ath79: Utilize new LED modes from diag.sh for Archer A7/C7 v5
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-08 18:37:04 +02:00
Adrian Schmutzler
9888f1b96c ath79: Consolidate LEDs in Archer A7/C7 v5 DTSI
Definition is split here without obvious reason. Just merge it
(and align order to that from C7 v4).

Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-04-08 18:37:04 +02:00
Christian Mauderer
8a4dc6f48c ath79: add support for Ubiquiti airCube ISP
The Ubiquiti Network airCube ISP is a cube shaped 2.4 GHz with internal
2x2 MIMO antennas. It can be supplied via a USB connector or via PoE.
There are for 10/100 Mbps ports (1 * WAN + 3 * LAN). There is an
optional PoE passthrough from the first LAN port to the WAN port.

SoC:       Qualcomm / Atheros QCA9533-BL3A
RAM:       64 MB DDR2
Flash:     16 MB SPI NOR
Ethernet:  4x 10/100 Mbps (1 WAN + 3 LAN)
LEDS:      1x via a SPI controller (not yet supported)
Buttons:   1x Reset
Serial:    1x (only RX and TX); 115200 baud, 8N1

Missing points:
- LED not yet supported
- Factory upgrade via web IF or TFTP recovery not yet supported
  (Needs RSA signed images, for details see PR#1958)

The serial port is on a four pin connextor labeled J1 and located
between Ethernet and USB connector. The pinout is:
1. 3V3 (out)
2. Rx (in)
3. Tx (out)
4. GND

Upgrading via serial port / U-Boot:
- Connect the serial port via a level converter
- Power the system and stop U-Boot with pressing any key when `Hit any
  key to stop autoboot` is displayed. Note: Pressing space multiple
  times untill U-Boot reaches that location works well.
- Connect a PC with the IP 192.168.1.100 (or some other in that net)
  running a TFTP-Server to one of the LAN ports. Copy the sysupgrade
  image to the server.
- Set the U-Boot server IP with
    setenv serverip 192.168.1.100
- Load the flash image to RAM with
    tftpboot 0x81000000 sysupgrade.bin
- Erase the flash with
    erase 0x9f050000 0x9ffaffff
- Write the new flash content with
    cp 0x81000000 0x9f050000 ${filesize}
- Reset the device with
    reset

Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
[removed full stop in subject and added lockdown note to commit message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Markus Scheck
de2f888024 ath79: add support for OCEDO Ursus
SOC:   Qualcomm Atheros QCA9558
RAM:   128MB
FLASH: 16MB (Macronix MX25L12845EMI-10G)
WLAN1: QCA9558 2.4GHz 802.11bgn 3SS
WLAN2: QCA9880 5GHz 802.11ac 3SS
LED:   Power, LAN1, LAN2, 2.4GHz, 5GHz
Serial:Next to SPI Flash,
       Pinout is 3V3 - GND - TX - RX (Square Pin is 3V3)
       The Serial setting is 115200-8-N-1

INSTALLATION:

1. Serve an OpenWrt ramdisk image named "ursus.bin".
   Set your IP-address to 192.168.100.8/24.
2. Connect to the serial. Power up the device and interrupt
   the boot process.
3. Set the correct bootcmd with
   > setenv bootcmd run bootcmd_1
   > saveenv
4. Run
   > tftpboot 0x81000000 ursus.bin
   > bootm 0x81000000
5. Wait for OpenWrt to boot up.
6. Transfer OpenWrt sysupdate image and flash via sysupgrade.

Signed-off-by: Markus Scheck <markus.scheck1@gmail.com>
Tested-by: David Bauer <mail@david-bauer.net>
[whitespace fix, renamed LED labels and SoC type fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Petr Štetiar
189aa1748b ath79: ag71xx: Enable tx hang workaround for the rest of ar724x SoCs
In ar71xx we check for stuck DMA on devices which fall in the is_ar724x
SoC group (ar724x, ar933x, ar934x, qca9533, tp9343, qca955x, qca956x).

In ath79 we're currently performing this check only for devices with
ar7240 SoC, so this patch tries to sync the dma stuck checking behavior
with what is being done in ar71xx.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Petr Štetiar
31ea08a64b ar71xx: ag71xx: Fix broken networking on some devices (FS#2177)
It was reported, that latest ar71xx builds have broken networking on
TP-Link TL-WPA8630 and Nanostation M5 XW devices and that by reverting
the offending commit, everything is back to normal.

Fixes: d3506d1 ("ar71xx: ag71xx: fix compile error when enabling debug")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Petr Štetiar
0f8cdc28af ar71xx: Add support for Ubiquity Bullet M (XW)
CPU: AR9342 SoC
RAM:     64 MB DDR2
Flash:    8 MB NOR SPI
Ports:  100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART:     1 UART on PCB marked as J1 with 115200 8N1 config
LEDs:       Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons:    Reset

UART connection details

  .---------------------------------.
  |                                 |
[ETH]          J1                 [ANT]
  |    o VCC o RX o TX o GND        |
  `---------------------------------'

Flashing instructions using recovery method over TFTP

 1. Unplug the ethernet cable from the router.
 2. Using paper clip press and hold the router's reset button. Make sure
    you can feel it depressed by the paper clip. Do not release the button
    until step 4.
 3. While keeping the reset button pressed in, plug the ethernet cable
    back into the AP. Keep the reset button depressed until you see the
    device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
    LED2/LED4), this may take up to 25 seconds.
 4. You may release the reset button, now the device should be in TFTP
    transfer mode.
 5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
    should work.
 6. Plug the PoE injector's LAN cable directly to your computer.
 7. Start tftp client and issue following commands:
     tftp> binary
     tftp> connect 192.168.1.20
     tftp> put openwrt-ar71xx-generic-ubnt-bullet-m-xw-squashfs-factory.bin

Tested only on Bullet M2HP.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Petr Štetiar
6009b3fd58 ar71xx: ubnt-m-xw: Fix factory image flashing using TFTP recovery
This is backport of the same functionality in ath79, from commit
 d42a7c469 ("ath79: ubnt-m-xw: Fix factory image flashing using TFTP
             recovery method")

Ubiquity allows flashing of unsigned factory images via TFTP recovery
method[1]. They claim in airOS v6.0.7 release changelog[2] following:

 All future airOS versions will be signed in this way and not allow
 unsigned firmware to be loaded except via TFTP.

U-boot bootloader on M-XW devices expects factory image revision
version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
(May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
number is actually a number, but in currently generated images there's
OpenWrt text and so the check fails:

 Hit any key to stop autoboot:  0
 Setting default IP 192.168.1.20
 Starting TFTP server...
 Receiving file from 192.168.1.25:38438
 Received 4981148 bytes
 Firmware check failed! (1)

By placing arbitrary correct number first in major version, we make the
bootloader happy and we can flash factory images over TFTP again:

 Received 3801500 bytes
 Firmware Version: XW.ar934x.v6.0.4-42.OpenWrt-r9766+2-be42e44
 Setting U-Boot environment variables
 Un-Protected 1 sectors
 Erasing Flash.... done

Patch provided by AREDN[3] project, tested on Bullet M2 XW.

1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points
2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt
3. https://github.com/aredn

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Petr Štetiar
d23222a96c imx6: Add support for Toradex Apalis family of CoMs
This patch adds support for the following computer on modules (CoM) from
Toradex[A]:

 Apalis iMX6 Quad 2GB IT - i.MX 6Quad 800MHz, 2GB DDR3, 4GB eMMC
                                             -40° to +85° C Temp
 Apalis iMX6 Quad 1GB    - i.MX 6Quad 1GHz,   1GB DDR3, 4GB eMMC
                                               0° to +70° C Temp
 Apalis iMX6 Dual 1GB IT - i.MX 6Dual 800MHz, 1GB DDR3, 4GB eMMC
                                             -40° to +85° C Temp
 Apalis iMX6 Dual 512MB  - i.MX 6Dual 1GHz, 512MB DDR3, 4GB eMMC
                                               0° to +70° C Temp

I've developed and tested it on Quad 2GB IT v1.1A and Dual 512MB v1.1A
CoMs, using Ixora[B] carrier board v1.0A, but it should hopefuly work on
Eval[C] board as well.

A. https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-freescale-imx-6
B. https://www.toradex.com/products/carrier-board/ixora-carrier-board
C. https://www.toradex.com/products/carrier-board/apalis-evaluation-board

Flashing/recovery instructions:

 1. Download and compile imx_loader for OpenWrt from
    https://github.com/ynezz/imx_loader

 2. Enter recovery mode as desribed in
    https://developer.toradex.com/knowledge-base/imx-recovery-mode

 3. Connect board via USB to the host computer, check that it's connected
    by lsusb:

    15a2:0054 Freescale Semiconductor, Inc. i.MX 6Dual/6Quad SystemOnChip
              in RecoveryMode

 4. Copy following OpenWrt images to imx_loader directory:
         SPL
         u-boot.img
         u-boot-with-spl.imx
         openwrt-imx6-apalis-recovery.scr
         openwrt-imx6-apalis-squashfs.combined.bin

 5. Run imx_usb in imx_loader directory

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
Petr Štetiar
dc1a73984e imx6: image: Split imx6-sdcard image for reusability
I'm going to reuse the imx6-sdcard image commands for building of Apalis
eMMC images.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:03 +02:00
Koen Vandeputte
8df12d76c6 kernel: bump 4.19 to 4.19.34
Refreshed all patches.

Removed:
- 030-PCI-dwc-skip-MSI-init-if-MSIs-have-been-explicitly-d.patch

Altered:
- 366-netfilter-nf_flow_table-clean-up-and-fix-dst-handlin.patch
- 650-netfilter-add-xt_OFFLOAD-target.patch
- 662-remove_pfifo_fast.patch
- 332-arc-add-OWRTDTB-section.patch
- 100-clocksource-drivers-arch_timer-Workaround-for-Allwin.patch
- 702-phy_add_aneg_done_function.patch

New symbols:
- ARC_IRQ_NO_AUTOSAVE
- SUN50I_ERRATUM_UNKNOWN1

Compile-tested: cns3xxx, imx6, sunxi
Runtime-tested: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-08 14:53:39 +02:00
Koen Vandeputte
5387bc9cbb kernel: bump 4.14 to 4.14.111
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-08 14:53:39 +02:00
Koen Vandeputte
1138e0f887 kernel: bump 4.9 to 4.9.168
Refreshed all patches.

Compile-tested on: ar7
Runtime-tested on: none

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-08 14:53:39 +02:00
Koen Vandeputte
5eac37624f kernel: bump 4.14 to 4.14.110
Refreshed all patches.

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-04-08 12:07:28 +02:00
Kip Porterfield
b812a7fa68 ramips: correct DTS for Belkin F9K1109v1 to include switch definition
Add switch definition for the rtl8367b switch to the DTS/DTSi for
the Belkin F9K1109v1 that was mistakenly omitted from the initial
commit.

Fixes: 017ec068e3 (ramips: add support for Belkin F9K1109v1)
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
2019-04-06 19:14:06 +02:00
INAGAKI Hiroshi
643fcfc8d6 ath79: add support for NEC Aterm WG1200CR
NEC Aterm WG1200CR is a 2.4/5 GHz band 11ac router,
based on Qualcomm Atheros QCA9563.

Specification:

- SoC		: Qualcomm Atheros QCA9563
- RAM		: DDR2 128 MiB
- Flash		: SPI-NOR 8 MiB
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: QCA9563 (SoC)
  - 5 GHz	: QCA9888
- Ethernet	: 2x 10/100/1000 Mbps
  - Switch	: QCA8334
- LEDs/Input	: 12x/4x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - JP1: Vcc, GND, NC, TX, RX from power connector side
  - 115200 bps

Flash instruction using factory image:

1. Boot WG1200CR normaly
2. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Known issues:

- cannot be controlled LEDs other than Power (Green/Red)
  - only Power LEDs are connected to SoC GPIO; other LEDs
    connected to the gpiochip on ath10k chip (QCA9888)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [commit
message formatting]
2019-04-06 19:14:06 +02:00
Chuanhong Guo
d80a1c6e2c ramips: backport mt7621-spi from linux-next-20190329
Upstream driver has gone through a series of cleanup and was moved
from drivers/staging into drivers/spi. Backport it to replace our
messy driver.

Tested-by: Jörg Schüler-Maroldt <joerg-linux@arcor.de>
[LinkIt Smart 7688, AcSIP AI7688H Wi-Fi module]
Tested-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Tian Xiao bo <peterwillcn@gmail.com>
[Newifi-D2 MediaTek MT7621 ver:1 eco:3]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-04-06 19:14:06 +02:00
Adrian Schmutzler
0eef05fb36 ath79: Utilize tplink-safeloader definition
Currently, tplink-safeloader definition is only used a base for
another common definition.

This patch adjusts tplink-safeloader so it can be actually used
for some targets in generic-tp-link.mk.

This patch is cosmetic except for the order of
"check-size $$$$(IMAGE_SIZE)" and "append-metadata" exchanged
for the tplink_re350k-v1 .

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [dealed with
tplink_cpe210-v2 and tplink_cpe210-v3, removed tplink-safeloader-uimage's
extra IMAGE/sysupgrade.bin rule]
2019-04-06 19:14:06 +02:00
David Bauer
b19c48dc34 ramips: enable R6120 USB power
Enable the USB power for the Netgear R6120. Otherwise, no power is
supplied to an attached USB device.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-04-06 19:14:06 +02:00
Tomasz Maciej Nowak
bac2c4d2fb ath79: engenius epg5000: add leds migration script
With transition from ar71xx to ath79 some of devices change their naming
of LEDs. When upgrading from ar71xx target images this will require the
user to adjust previously working configuration. This commit adds
migration script which can be used to rename old names to new ones.
With this previously working configuration will be automatically
adjusted, wihtout user intervention.

This commit adds migration case for EnGenius EPG5000, the wireless LEDs
names have changed from epg5000:blue:wlan2-g and epg5000:blue:wlan-5g to
epg5000:blue:wlan2g and epg5000:blue:wlan5g.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-04-06 19:14:05 +02:00
Zhao Yu
32689e93c4 ramips: add support for Youku YK-L2
Hardware spec:

CPU: MTK MT7621A
RAM: 256MB
ROM: 16MB SPI Flash
WiFi: MT7603EN + MT7612EN
Button: 2 buttons (reset, wps)
LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB)
Ethernet: 3 ports, 2 LAN + 1 WAN
Other: USB3.0

Flashing instructions:

Visit the openwrt forum topic for this router:
https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692

to get the bootloader and unlock firmware.

0. upgrade your router with the telnet firmware via the
   firmware upgrade page on the webui.

1. telnet 192.168.11.1 from your PC

2. Download the pb-boot-youku_l2-20190317-61b6d33.bin and transfer
   it to the /tmp directory of the router.

3. mtd write /tmp/pb-boot-youku_l2-20190317-61b6d33.bin Bootloader

4. turn off the power

5. Push the reset button while turning on the router and
   wait until LED start blinking (~10sec.)

6. Connect Ethernet port and goto http://192.168.1.1.

7. Upload the firmware to firmware restore page in webui.

Signed-off-by: Zhao Yu <574249312@qq.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the
flashing instructions, fixed author]
2019-04-06 19:13:49 +02:00
Daniel Engberg
6c22545225 target/octeon: Add Linux 4.19 support
This commit adds support for Linux 4.19 kernel, various cleanups
listed below.

Drop 170-cisco-hack.patch as these devices never seems to have been
supported.

Unset kernel symbols:

* CONFIG_CAVIUM_CN63XXP1=y
  No supported hardware uses CN63XXP1 and it causes "slight decrease in
  performance"
  Source: https://cateee.net/lkddb/web-lkddb/CAVIUM_CN63XXP1.html

* CONFIG_USB_OCTEON_EHCI=y
  CONFIG_USB_OCTEON_OHCI=y
  Deprecated
  Source: https://cateee.net/lkddb/web-lkddb/USB_OCTEON_EHCI.html
  https://cateee.net/lkddb/web-lkddb/USB_OCTEON_OHCI.html

Removed kernel symbols:

* # CONFIG_ARCH_HIBERNATION_POSSIBLE=y
* CONFIG_ARCH_SUSPEND_POSSIBLE=y
  These are not in if you do a vanilla config of a MIPS Octeon kernel
  and I can't find any references about support on this platform.

* # CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
* CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
  No need to have this in by default, not defined in most other targets

* CONFIG_CRASH_CORE=y
  Can't find any documentation why this should be enabled by default

* CONFIG_DEBUG_INFO=y
  Set by https://github.com/openwrt/openwrt/blob/master/config/Config-kernel.in#L134

* CONFIG_DEBUG_SPINLOCK=y
  No need to have this in by default

* CONFIG_DEFAULT_HUNG_TASK_TIMEOUT=120
  Already set by default
  Source: https://cateee.net/lkddb/web-lkddb/DEFAULT_HUNG_TASK_TIMEOUT.html

* CONFIG_DETECT_HUNG_TASK=y
  No need to have this in by default, not defined in most other targets

* CONFIG_HAVE_DEBUG_KMEMLEAK=y
  No need to have this in by default, not defined in most other targets

* CONFIG_HAVE_DEBUG_STACKOVERFLOW=y
  No need to have this in by default

* CONFIG_HAVE_IDE=y
  None of the supported devices have IDE

* CONFIG_HZ=250
* # CONFIG_HZ_100 is not set
* CONFIG_HZ_250=y
  This is broken with generic config

* CONFIG_KALLSYMS=y
  No need to have this in by default, not defined in most other targets

* CONFIG_KEXEC=y
* CONFIG_KEXEC_CORE=y
  No need to have this in by default, not defined in most other targets

* CONFIG_HAVE_KVM=y
  No need to have this in by default

* CONFIG_SCHED_DEBUG=y
  No need to have this in by default, not defined in most other targets

* CONFIG_SYSFS_DEPRECATED=y
  Deprecated symbol
  Source: https://cateee.net/lkddb/web-lkddb/SYSFS_DEPRECATED.html

* CONFIG_SYSFS_DEPRECATED_V2=y
  Discouraged usage in general
  Source: https://cateee.net/lkddb/web-lkddb/SYSFS_DEPRECATED_V2.html

* CONFIG_UNINLINE_SPIN_UNLOCK=y
  No need to have this in by default, not defined in most other targets
  Source: https://github.com/openSUSE/kernel/blob/master/lib/Kconfig.debug#L1137

* CONFIG_ZLIB_INFLATE=y
  No need to have this in by default, not defined in most other targets

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
2019-04-06 16:31:10 +02:00
Tomasz Maciej Nowak
2e5a0b81ec mvebu: sysupgrade: sdcard: keep user added partitons
Currently sysupgrade overwrites whole disk and destroys partitions added
by user. Sync the sysupgrade code with the one present in x86 target to
remedy this behaviour.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-04-06 16:31:10 +02:00
Tomasz Maciej Nowak
4e8345ff68 mvebu: base-files: autodetect upgrade device
Since some boards could be also booted from other mediums than SD card,
lets make the upgrade block device autodetected.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-04-06 16:31:10 +02:00
Tomasz Maciej Nowak
727c3df5bb mvebu: shrink amount of packages and reorganize them
Since most of devices using SD card image to boot, use ext4 as boot
files system we can drop fat fs related packages. Also move packages
which are added repeatedly across subtargets to their default packages,
with droping the ones that are enabled in target kernel configugation.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-04-06 16:31:10 +02:00
Tomasz Maciej Nowak
55b4ff7f73 mvebu: use ext4 for clearfog image bootfs
This will allow to drop additional packages and shrink image size.

Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-04-06 16:31:10 +02:00
Tomasz Maciej Nowak
910eb994eb mvebu: make bootfs size for sdcard image configurable
Let's take this oportunity to implement boot-part and rootfs-part feature
flags.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-04-06 16:31:10 +02:00
Luis Araneda
78a3c51985 zynq: replace storage related configs by packages
Select build-in packages by default and remove the
associated kernel configs

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2019-04-06 16:31:10 +02:00
Luis Araneda
3db12da7cd zynq: replace CAN kconfig options by device packages
The options are managed on a generic way by the can
kmod packages

Additionally, select can packages only for devices that
currently has CAN enabled, which is only the ZC702

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
2019-04-06 16:31:10 +02:00