We currently enable DEBUG_INFO_REDUCED for all targets via the generic
kernel config. There is only one subtarget, layerscape/armv8_64b, that
overrides this setting. As there is no explanation for this in the
commit message that introduced this, and question to its author went
unanswered, let's simply drop this symbol from the subtarget config.
This way, we have consistency across the tree, and we do not have to
introduce a special case when moving this symbol to an OpenWrt kernel
config option.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Building tools/resolve_btfids requires libelf and zlib. Without this
build fix, the kernel build system will not find these dependencies.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This backports a patch from Linux 5.10.116 to fix a compile problem
introduced in 5.10.114.
drivers/usb/phy/phy-generic.c could not find
devm_regulator_get_exclusive().
Fixes: 8592df67f4 ("kernel: bump 5.10 to 5.10.114")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The SERCOMM NA502s is a smart home gateway manufactured by SERCOMM and sold
under different brands (among others, A1 Telekom Austria SmartHome Premium
Gateway). It has multi-protocol radio support in addition to LAN and WiFi.
Note: BLE and audio are currently unsupported.
Specifications
--------------
- MT7621ST 880MHz, Single-Core, Dual-Thread
- MT7603EN 2.4GHz WiFi
- MT7662EN 5GHz WiFi + BLE
- 128MiB NAND
- 256MiB DDR3 RAM
- SD3503 ZWave Controller
- EM357 Zigbee Coordinator
- Telit UMTS module
- Rechargeable battery
- speaker and microphone
MAC address assignment
----------------------
LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches
the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the
OEM firmware does not enable 5GHz WiFi.
Installation
------------
Attach serial console, then boot the initramfs image via TFTP.
Once inside OpenWrt, run sysupgrade -n with the sysupgrade file.
Attention: The device has a dual-firmware design. We overwrite kernel2,
since kernel1 contains an automatic recovery image.
If you get NAND ECC errors and are stuck with bad eraseblocks, try to
erase the mtd partition first with
mtd unlock ubi
mtd erase ubi
This should only be needed once.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
this adds the mediatek,led_source dts binding for
Asus RT-AC1200 devices' dtsi, for correct switch LED
behavior.
The dts-binding is introduced in commit:
65dc9e0980
Without this, we only have constantly very fast
blinking LEDs, which don't react on any traffic or
LAN events at all.
Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
Some revisions of the FRITZ!7530 use a Toshiba NAND with 8 bit ECC in
contrast to the Macronix NAND with 4 bit ECC. This removes the hardcoded
ECC strength and step size as set in qcom-ipq4019.dtsi, thus relying on the
kernel NAND detection routines to correclty set up the ECC parameters.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
The Toshiba TC58NVG0S3HTA00 is detected with 64 byte OOB while the flash
has 128 byte OOB. This adds a static NAND ID entry to correct this.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
ZTE MF286A and MF286R feature a "power switch override" GPIO in stock
firmware as means to prevent power interruption during firmware update,
especially when used with internal battery.
To ensure that this GPIO is
properly driven as in stock firmware, configure it with userspace GPIO
switch.
It was observed that on some units, the modem would not be
restarted together with the board itself on reboot, this should help
with that as well.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
On GL-AR300M Series GPIO17 described as I2C SDA in Device Tree.
Because of GPIO_OUT_FUNCTION4 register was not initialized on start,
GPIO17 was uncontrollable, it always in high state. According to QCA9531
documentation, default setting of GPIO17 is SYS_RST_L. In order to make
GPIO17 controllable, it should write value 0x00 on bits [15:8] of
GPIO_OUT_FUNCTION4 register, located at 0x1804003C address.
Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
All Freescale processors used in this target are capable to detect error
and correction. [1] It can not be used as kernel module. [2] This is
helpful to report hardware errors.
It enables three kernel options:
- EDAC, which is a subsystem
- EDAC_LEGACY_SYSFS, it enables sysfq nodes
- MP85XX, support for Freescale MPC8349, MPC8560, MPC8540, MPC8548, T4240
EDAC is already enabled for following targets:
qoriq, octeon, octeontx and zynq.
[1] https://cateee.net/lkddb/web-lkddb/EDAC.html
[2] https://patchwork.ozlabs.org/patch/554908/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
This makes it possible to fix Netgear WNDAP620+660 DTS ugliness.
Bring back the dtb and firmware partitions for the WNDR4700.
Thank you, mans0n.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.
Fixes: #9824
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Do not reset the RTL930x SerDes on link changes, instead set up
the SDS with internal PHYs for the SFP+ ports only.
This fixes the 8 1GBit ports on the Zyxel XGS1250 which
do not work without this patch.
A complete SerDes reset was performed on all SerDes links. For copper
1Gbit ports, this is commonly a single XGMII link to an RTL8218D. There
is however no support for setting up the XGMII link on RTL9300/RTL9310,
thereby wiping the (RX/TX) setup done by u-boot and breaking the 1GBit
ports. No SerDes reset should be done for these links.
The handling of SGMII/HiSGMII, 1000BX or 10GR links is actually entirely
different. All these modes need to be suitably RX calibrated and the
pre- main and post- amplifiers set up properly for TX.
The 10GBit SFP+ fiber links are recalibrated instead of reset, which
e.g. is necessary when someone pulls a module out and puts another in.
This makes swapping out 10GBit fiber modules possible. 1GBit modules are
not yet supported, nor any modules with an internal phy.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
[rewrite commit message based on discussion]
Link: http://lists.infradead.org/pipermail/openwrt-devel/2022-May/038623.html
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Specifications:
SoC: MediaTek MT7621
RAM: 256 MB
Flash: 32 MB
WiFi: MediaTek MT7915E
Switch: 1 WAN, 4 LAN (Gigabit)
Ports: 1 USB 3.0
Buttons: Reset, WPS
LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
Power: DC 12V 1A tip positive
Installation:
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Recovery:
Loads only signed manufacture firmware due to bootloader RSA verification
serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
connect to any lan ethernet port
power on the device while holding the reset button
wait at least 8 seconds before releasing reset button for image to
download
Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com>
[ensure unique wireless MAC, fix GPIO pingroup]
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes a bug where frames sent to the switch itself were
flooded to all ports unless the MAC address of the CPU-port
was learned otherwise.
Tested-by: Wenli Looi <wlooi@ucalgary.ca>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
[fix code formatting]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The ZyXEL GS1900-16 is a 16 port gigabit switch similar to other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-16
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB Macronix MX25L12835F
* RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8HE
* Ethernet: 16x 10/100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
16 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J12) with populated standard pin connector on
the right back of the PCB.
Pinout (front to back):
+ Pin 1 - VCC marked with white dot
+ Pin 2 - RX
+ Pin 3 - TX
+ PIn 4 - GND
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
file amd select open so File Path is update with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-16 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Raylynn Knight <rayknight@me.com>
[removed duplicate patch title, align RAM specification]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
This workaround will allow the MA5671A to function, ignoring the
persistently asserted tx-fault.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
(added 5.15 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch copies over refreshed config and patches from 5.10
with the following changes:
- dropped superfluous tc654/tc655 variant detection patch
(tc654 support will become available upstream starting with
5.17-rc7+).
- dropped xhci msi(x) workaround... as the broken MSI(X)
is now gone.
- dropped dwc2 workaround since the driver was fixed and it
works without it.
Please note: Netgear WNDAP660 & WNDAP620 users:
Due to the kernel's size increase, uboot will likely break
because it is overwrite the kernel during decompression.
To fix this (and debrick affected devices, no reflash
necessary), attach the RJ45-Serial-Console cable and
enter the following in the uboot prompt during bootup:
setenv kernel_addr_r 1100000
saveenv
run bootcmd
to restore the old/previous behavior:
setenv kernel_addr_r 600000
saveenv
run bootcmd
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
upstream linux have these watchdogs locked behind X86.
These will not build on other architectures. So move them
to target/linux/x86/modules.mk
drivers/watchdog/Kconfig:
|config F71808E_WDT
| tristate "Fintek F718xx, F818xx Super I/O Watchdog"
| depends on X86
|[...]
|config IT87_WDT
| tristate "IT87 Watchdog Timer"
| depends on X86
|[...]
|config ITCO_WDT
| tristate "Intel TCO Timer/Watchdog"
| depends on (X86 || IA64) && PCI
|[...]
|config W83627HF_WDT
| tristate "Watchdog timer for W83627HF/W83627DHG and compatibles"
| depends on X86
|[...]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Grommish reported the dreaded build error that happend with 5.4
since the kernel didn't have the cgpio v2 interface. His reason
for the removed 5.4 was that the octeon target had a memory leak
issue, so he had to backport the removed 5.4 kernel for his tests.
Chen Minqiang chimed in and noted that no matter what (i.e.
@TARGET_x86 in depends) didn't prevent the package from being build
on other targets.
From what I can tell, the reason for this was that +nu801 meant
that kmod-meraki-mx100 pulled in an unconditional dependency as
part of to the kernel build.
|scripts/package-metadata.pl mk tmp/.packageinfo
|
|$(curdir)/kernel/linux/compile += $(curdir)/firmware/linux-firmware/compile \
| $(curdir)/firmware/prism54-firmware/compile \
| $(curdir)/kernel/gpio-button-hotplug/compile \
| >>> $(curdir)/system/gpio-cdev/nu801/compile <<<
change this by making the dependency conditional on the
meraki-mx100 module itself. Note that the nu801 enables/sets
the KCONFIG for the cgpio v2 interface itself, since the
userspace program and not the kernel meraki-mx100 relies on it.
Reference: <https://github.com/openwrt/openwrt/commit/eeb8fd4ce7e9>
Reported-by: Grommish <grommish@gmail.com>
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
QEMU+Libvirt can emulate the ib700wdt watchdogs
which due to its I/O-Port mapping makes it x86
specific.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
QEMU can emulate several watchdogs:
aspeed SoC, i6300esb, ib700wdt, imx2, cmsdk-apb and sbsa_gwdt.
Out of these, the ARM SBSA Generic Watchdog (sbsa_gwdt)
makes the most sense for the armvirt' 64 target. Both imx2 and
aspeed are guarded by special vendor specific CONFIG_ in the
upstream kernel.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Commit f4fb63d2ab ("ipq40xx: 5.10: move AR40xx to MDIO drivers") moved
the ar40xx driver files to kernel version specific directories to place
them in different subdirectory in kernel tree. But now kernel 5.4 is
gone and there is no reason to keep them separate. Move them back to
common files/ directory.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Also apply commit ab7e53e5cc ("ipq40xx: 5.10: fix ar40xx driver") to
5.15 driver.
The commit fixes the data corruption on TX packets. Packets are
transmitted, but their contents are replaced with zeros. This error is
caused by the lack of guard (50 ms) intervals between calibration phases.
This error is treated by adding mdelay(50) to the calibration function
code. In the original qca-ssda code, these mdelays were existing, but in
the ar41xx.c they are gone.
Fixes: 87318eb179 ("ipq40xx: 5:15: copy config and patch from 5.10")
Signed-off-by: Nick Hainke <vincent@systemli.org>
According wiki https://docs.gl-inet.com/en/2/hardware/mt300n-v2/
GL-MT300N-V2 have I2C interface on GPIO4, GPIO5.
Adding I2C in device tree make possible using I2C on this device.
Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
Hardware specs:
SoC: Qualcomm IPQ8065 (dual core Cortex-A15)
RAM: 512 MB DDR3
Flash: 256 MB NAND, 32 MB NOR
WiFi: QCA9983 2.4 GHz, QCA9984 5 GHz
Switch: QCA8337
Ethernet: 5x 10/100/1000 Mbit/s
USB: 1x USB 3.0 Type-A
Buttons: WPS, Reset
Power: 12 VDC, 2.5 A
Ethernet ports:
1x WAN: connected to eth2
4x LAN: connected via the switch to eth0 and eth1
(eth0 is disabled in OEM firmware)
MAC addresses (OEM and OpenWrt):
fw_env @ 0x00 d4🆎82:??:??:?a LAN (eth1)
fw_env @ 0x06 d4🆎82:??:??:?b WAN (eth2)
fw_env @ 0x0c d4🆎82:??:??:?c WLAN 2.4 GHz (ath1)
fw_env @ 0x12 d4🆎82:??:??:?d WLAN 5 GHz (ath0)
fw_env @ 0x18 d4🆎82:??:??:?e OEM usage unknown (eth0 in OpenWrt)
OID d4🆎82 is registered to:
ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US
More info:
https://openwrt.org/inbox/toh/arris/tr4400_v2
IMPORTANT:
This port requires moving the 'fw_env' partition prior to first boot to
consolidate 70% of the usable space in flash into a contiguous partition.
'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords.
Its contents must be copied to 'rootfs_1' prior to booting via initramfs.
Note that the stock 'fw_env' partition will be wiped during sysupgrade.
A writable 'stock_fw_env' partition pointing to the old, stock location
is included in the port to help rolling back this change if desired.
Installation:
- Requires serial access and a TFTP server.
- Fully boot stock, press ENTER, type in:
mtd erase /dev/mtd21
dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21
umount /config && ubidetach -m 23 && mtd erase /dev/mtd23
- Reboot and interrupt U-Boot by pressing a key, type in:
set mtdids 'nand0=nand0'
set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)'
set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm'
env save
- Setup TFTP server serving initramfs image as 'recovery.bin', type in:
set ipaddr 192.168.1.1
set serverip 192.168.1.2
tftpboot recovery.bin && bootm
- Use sysupgrade to install squashfs image.
This port is based on work done by AmadeusGhost <amadeus@jmu.edu.cn>.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
[add 5.15 changes for 0069-arm-boot-add-dts-files.patch]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Add NVRAM quirks script for the bcm53xx target. Split NVRAM quirks for the
bcm47xx and bcm53xx targets. Move clear partialboot NVRAM quirk for Linksys
EA9500 here. Add set wireless LED behaviour quirk for Asus RT-AC88U.
Use boot() instead of start() as nvram commands are meant to be executed
only once, at boot.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
this adds the new dts-binding "mediatek,led_source"
currently for MT7628AN and MT7688 built-in switches,
which is documented as a 3-bit field configuring the
switch LEDs for various control schemes from 0 to 3.
Normally this is not needed, but e.g. for Asus RT-AC1200-V2
it is a must to set it to the anyway undocumented value
of 4, to have the switch LEDs react correctly on link/act
events. This is an MT7628DAN device, but I doubt this is
a speciality of this particular SoC.
Also added the RT305X_ESW_LED_OFF value to LED states.
Did also rename the register RT5350_EWS_REG_LED_POLARITY
to RT5350_EWS_REG_LED_CONTROL, which is the correct name.
Also making use of defines for some hardcoded values.
Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
This patch configures kernel testing version for kirkwood target.
Compile tested: all
Run tested: Endian 4i
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
