patch 150-arch-powerpc-simpleboot-prevent-overwrite-of-CPU1-sp.patch
was missed durring copy from 5.15 to 6.1.
This patch restore it.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Add support for Gateworks Venice imx8m family of boards:
- required kernel modules for on-board devices
- image generation
- initial network config
- sysupgrade support
The resulting compressed disk image
(bin/targets/imx/cortexa53/openwrt-imx-cortexa53-gateworks_venice-squashfs-img.gz)
can be installed on a Gateworks venice board via U-Boot:
u-boot=> tftpboot $loadaddr openwrt-imx-cortexa53-gateworks_venice-squashfs-img.gz && \
gzwrite mmc $dev $loadaddr $filesize
WARNING: this will overwrite any boot firmware on the eMMC user hardware
partition which if being used will brick your board requiring JTAG to
re-program boot firmware and recover
The compressed disk image contains the partition table and filesystems only
and that it is expected that boot firmware is installed properly on the
eMMC boot0 hardware partition. The easiest way to ensure this is to
use the Gateworks JTAG adapter/process to install the latest boot firmware
as follows from a Linux host:
wget http://dev.gateworks.com/jtag/jtag_usbv4
chmod +x jtag_usbv4
wget http://dev.gateworks.com/venice/images/firmware-venice-imx8mm.bin
sudo ./jtag_usbv4 -p firmware-venice-imx8mm.bin
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add imx8m support:
- add a cortexa53 subtarget to imx
- move ARCH and KERNELNAME to subtargets
- account for kernel modules that are not used for cortexa53
No device-specific targets or firmware images are created yet but all
imx8m* dtbs will be built.
enabling CONFIG_TARGET_ROOTFS_INITRAMFS results in
openwrt-imx-cortexa53-imx8m-initramfs-kernel.bin which has been
successfully booted on an imx8mm-evk using the following:
u-boot=> tftpboot $fdt_addr_r image-imx8mm-evk.dtb && \
tftpboot $kernel_addr_r openwrt-imx-cortexa53-imx8m-initramfs-kernel.bin && \
booti $kernel_addr_r - $fdt_addr_r
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add a hotplug script and add ttyATH1 on ELECOM WAB-I1750-PS to
/etc/inittab while booting for using that console as an OpenWrt console.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Register ttyS0 and ttyATH1 as Linux console on ELECOM WAB-I1750-PS.
ttyS0 provides "SERVICE" port and internal pin header for debugging and
recoverying by maker, ttyATH1 provides "SERIAL" port for configuration
by users.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The 6.1 kernel has caused another increase in kernel size, and now
it's more than 3MB:
WARNING: Image file iom_ix4-200d-uImage is too big: 3170394 > 3145728
WARNING: Image file iom_ix2-200-uImage is too big: 3171494 > 3145728
WARNING: Image file linksys_e4200-v2-uImage is too big: 3171879 > 3145728
WARNING: Image file linksys_ea4500-uImage is too big: 3171871 > 3145728
WARNING: Image file linksys_ea3500-uImage is too big: 3171651 > 3145728
This causes problems for 5 devices:
- Iomega StorCenter ix2/ix4
- Linksys EA3500/EA4200/EA4500
They have enough resources for proper operation with 6.1, but all of
them had a 3MB kernel size limit. Let's keep them alive and
resize kernel partitions to 4MB.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
6.1 testing version was introduced some time ago. Kernel size issues
are resolved now. Time to bump kernel version.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
When build images with the 6.1 kernel for all devices and all kmods,
there is one dependancy error:
pkg_hash_check_unresolved: cannot find dependency kmod-thermal
for kmod-hwmon-gpiofan
This commit fix that issue.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Copied from original Andrew's Lunn commit message:
The DSA framework has got more picky about always having a phy-mode
for the CPU port. The Kirkwood Ethernet is an RGMII port. Set the
switch to impose the RGMII delays.
Additionally, the cpu label has never actually been used in the
binding, so remove it.
This commit backport change from upstream and fix downstream EA3500 dts.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
TP-Link RE205 v3 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with external antennas.
It's based on MediaTek MT7628AN+MT7610EN like the RE200 v3/v4 but with
external antennas.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 5x LED (GPIO-controlled), 2x button
- UART connection holes on PCB (57600 8n1)
There are 2.4G and 5G LEDs in blue which are controlled separately.
Installation
------------
Installation is identical to RE200 v3 devices as described at
https://openwrt.org/toh/tp-link/re200#installation
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Recovery
--------
U-Boot seems to be locked on newer versions, if not it can be accessed over
the UART as described in the link above.
Signed-off-by: Steffen Loley <slo-src@web.de>
This service was unfunctional due to not having its executable bit set.
Furthermore, sysupgrade complains about the file being present in images.
Also, the tc654 driver doesn't provide pwm1_enable sysfs file, instead its
now called pwm1_mode.
Please note that the fan was always spinning. It should now turn off, when
there's enough the thermal headroom.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
D-Link DGS-1210-16 hangs when rebooting and has no support for the reset
button.
Fix both by enabling the same GPIOs for reboot and the reset button as
already used for D-Link DGS-1210-20 and D-Link DGS-1210-28.
Signed-off-by: Richard Kunze <kunze@tivano.de>
When rebasing patches on top of 6.1, a change that removed NF_TABLES
from NF_FLOW_TABLE's dependency was dropped accidentally, and iptables
flow offload module can only be built when nftables is selected.
Restore the change to fix it.
Fixes: 19a246bb65 ("generic: 6.1: manually refresh hack patches")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Radxa E25 is a network application carrier board for the Radxa CM3
Industrial (CM3I) SoM, which is based on the Rockchip RK3568 SoC.
It has the following features:
- MicroSD card socket, on board eMMC flash
- 2x 2.5GbE Realtek RTL8125B Ethernet transceiver
- 1x USB Type-C port (Power and Serial console)
- 1x USB 3.0 OTG port
- mini PCIe socket (USB or PCIe)
- ngff PCIe socket (USB or SATA)
- 1x User LED and 16x RGB LEDs
- 26-pin expansion header
Installation:
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Kernel 6.6 has changed the path of WLAN devices as the soc node was updated
to include an adress as well because according to spec it needed one:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v6.6.21&id=da6aa1111a17db11367817ddc10c5a6c188cdc44
So, this will break existing configuration as device path was changed for
example:
"platform/soc/c000000.wifi" to "platform/soc@0/c000000.wifi"
"platform/soc/c000000.wifi+1" to "platform/soc@0/c000000.wifi+1"
PCIe attached devices also have their path changed, so lets add a script
that will migrate the paths based on the detected running kernel version
so returning to kernel 6.1 will work as well.
Co-developed-by: Sean Khan <datapronix@protonmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Robert Marko <robimarko@gmail.com>
When building MT7629 with ALL_KMODS then we get prompted for
LEDS_SMARTRG_LED and this will break CI and in future buildbot compilation.
It depends on I2C so the symbol is hidden until ALL_KMODS is used and I2C
support is available, so disable the LEDS_SMARTRG_LED symbol in 6.6 config
intentionally as is done in the 6.1 mt7629 config.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Disable CONFIG_CRYPTO_SM4_ARM64_CE_CCM and CONFIG_CRYPTO_SM4_ARM64_CE_GCM
in the generic config like we do with similar CE symbols.
This avoids the need to disable them in individual targets.
Signed-off-by: Robert Marko <robimarko@gmail.com>
* have more defined PWM steps similar to the vendor's shell script doing
the same thing
* replace PWM values with experiencal values provided by forum users
* increase hyteresis to prevent changing fan speed every second
(just because it's annoying to listen to)
* add 'hot' trip point at 75 deg. to warn users that shutdown is imminent
Tested on Puzzle M902 only for now, PWM values for Puzzle M901 might be
slightly different but should quite certainly also be rised.
Suggested-by: Martin Gierschner <martin_gierschner@gmx.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The vendor u-boot knows nothing about UBI, and we used to have a
fixed-size kernel partition for vendor u-boot and UBI for rootfs.
However, that fixed partition becomes too small eventually, and
expanding it requires complicated procedure.
This commit changed the flash layout and added a second u-boot
where the kernel supposed to be.
Now the vendor u-boot chainloads our mainline u-boot, and our
u-boot reads kernel+rootfs from UBI, verifies it, and boot
into OpenWrt.
There are two possible ways to convert from the old fw:
Flash the factory image using mtd (provided by @rany2):
mount -o remount,ro /
mount -o remount,ro /overlay
cd /tmp
dd if=factory.bin bs=1M count=4 | mtd write - kernel
dd if=factory.bin bs=1M skip=4 | mtd -r write - ubi
Or, flash the 2nd u-boot via mtd and upload the firmware
to the 2nd u-boot using tftp:
1. prepare a tftp server at 192.168.1.254 to serve the
sysupgrade image:
openwrt-mediatek-mt7622-xiaomi_redmi-router-ax6s-squashfs-sysupgrade.itb
2. upload the ubi-loader.itb to OpenWrt /tmp, and flash it to
the old kernel partition:
mtd -r write openwrt-mediatek-mt7622-xiaomi_redmi-router-ax6s-ubi-loader.itb
3. The router should reboot and flash the sysupgrade image via TFTP.
Procedure for flashing from vendor firmware shouldn't change.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
With kernel 6.1 image size is too large for Edgerouter X current size
limit and is causing the buildbots to fail building so images for other
devices are not updated as well.
So, disable building Edgerouter X images until a workaround is found.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream commit e298d8a38b23 [0] changed method how to blink delays are pased
to function. Downstream commit must follow it.
[0] https://lore.kernel.org/r/20230510162234.291439-2-hdegoede@redhat.com
Reported-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Currently, 6 MAC addresses are read from the "boarddata1" partition and set for network interfaces in sequence.
This partition only contains 3 MAC addresses:
1. lan mac
2. wan mac
3. wlan5g mac
As result only lan2, lan3 and lan4 have correct (OUI) MAC addresses.
lan1, lan5 and wan interfaces get MAC addresses with incorrect OUI from random data on "boarddata1" partition.
This commit fix this and use first MAC for lan and second MAC for wan interfaces.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
The port 5 of most ipq60xx devices is connected to qca8075,
a few are connected to qca8081. So assume that the default
connection is qca8075 and set the phy mode to psgmii.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Marvell's thermal sensors do not support interrupts, so we need to
poll them. Reading temperature every second should be enough to
control the fan.
While at it, also make sure fan speed is reduced again if temperature
goes down.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
On Buffalo WXR-5590AX12, some LEDs don't have "function" property and
only "color" property is available for the newer binding of LED on
Linux Kernel.
2e659930d3 ("qualcommax: drop redundant label with new LED
color/function format") removes "label" property from LEDs, then,
multiple "<color>:" (ex.: "white:"/"red:") will be appeared as LED names
and renamed to "<color>:_<num>" ("ex.: "white:_1", "green:_2", ...) by
kernel.
logs:
[ 5.372863] leds-gpio leds: Led white: renamed to white:_1 due to name collision
[ 5.375796] leds-gpio leds: Led red: renamed to red:_1 due to name collision
/sys/class/leds:
root@OpenWrt:/# ls /sys/class/leds/
red: red:power white: white:power
red:_1 red:wlan white:_1 white:wlan
Fix this issue by adding missing "function" property to LEDs on Buffalo
WXR-5950AX12.
Note: there are no appropriate functions in dt-bindings/leds/common.h
for some LEDs, so use the hardcoded strings for them instead.
Fixes: 2e659930d3 ("qualcommax: drop redundant label with new LED color/function format")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
