The BUILD_VARIANT might differ from UBOOT_CONFIG, so point to a file we
are actually changing. Being here let's call 'Build/Configure/U-Boot'
definition, instead of definig the same command. This'll be more future
proof, if U-Boot configuration procedure will change.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The current version of ATF does not support power off for SGMII
COMPHY. Update to latest ATF to resolve this issue.
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
Add Netgear WNDR3700v2 to the list of supported boards.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
[rebase, adjusted commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add ubootenv uci config for gl-ar150, gl-domino and gl-mifi
Signed-off-by: Kimmo Vuorinen <kimmo.vuorinen@gmail.com>
[commit message/title facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In function `main` add calls to `free` for the variable `executable`.
This is needed because the variable `executable` is allocated but
never freed. This cause a memory leak.
Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
This patch introduces support for Netgear WNDR4500v3. Router
is very similar to WNDR4300v2 and is based on the same PCB.
Information gathered from various Internet sources (including
https://patchwork.ozlabs.org/patch/809227/) shows following
differences to WNDR4300v2:
* two USB 2.0 ports with separate LEDs
* USB LEDs soldered to secondary pads
* WPS and RFKILL buttons soldered to secondary pads
* described as N900 device with 3x3:3 MIMO for 2.4GHz radio
* power supply requirement is DC 12V 2.5A
* vendor HW ID suffix differs in one digit
* bigger chassis
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This patch introduces support for Netgear WNDR4300v2.
Specification
=============
* Description: Netgear WNDR4300 v2
* Loader: U-boot
* SOC: Qualcomm Atheros QCA9563 (775 MHz)
* RAM: 128 MiB
* Flash: 2 MiB SPI-NOR + 128 MiB SPI-NAND
- NOR: U-boot binary: 256 KiB
- NOR: U-boot environment: 64 KiB
- NOR: ART Backup: 64 KiB
- NOR: Config: 64 KiB
- NOR: Traffic Meter: 64 KiB
- NOR: POT: 64 KiB
- NOR: Reserved: 1408 KiB
- NOR: ART: 64 KiB
- NAND: Firmware: 25600 KiB (see notes for OpenWrt)
- NAND: Language: 2048 KiB
- NAND: mtdoops Crash Dump: 128 KiB
- NAND: Reserved: 103296 KiB
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8337)
* Wireless:
- 2.4 GHz b/g/n (internal)
- 5 GHz a/n (AR9580)
* USB: yes, 1 x USB 2.0
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN 2G (green)
- WLAN 5G (blue)
- 4 x LAN (amber/green)
- USB (green)
- WPS (green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 1.5A
* MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2
Important Notes
===============
0. NOR Flash (2 MiB) is not touched by OpenWrt installation.
1. NAND Flash (128 MiB) layout under OpenWrt is changed as follows:
all space is split between 4 MiB kernel and 124 MiB UBI areas;
vendor partitions (language and mtdoops) are removed; kernel space
size can be further expanded if needed; maximum image size is set
to 25600k for compatibility reasons and can also be increased.
2. CPU clock is 775 MHz, not 750 MHz.
3. 5 GHz wireless radio chip is Atheros AR9580-AR1A with bogus PCI
device ID 0xabcd. For ath9k driver to load successfully, this is
overriden in DTS with correct value for this chip, 0x0033.
4. RFKILL button is wired to AR9580 pin 9 which is normally disabled
by chip definition in ath9k code (0x0000F4FF gpio mask). Therefore
'qca,gpio-mask=<0xf6ff>' hack must be used for button to work
properly.
5. USB port is always on, no GPIO for 5V power control has been
identified.
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_nand=y
CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr4300-v2=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
This target is still on kernel 4.9, and it looks like there is no
active maintainer for this target anymore.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Was inadvertantly missed from the inital forward port from ar71xx to
ath79.
Fixes: 1588114cf2 ("ath79: add etactica-eg200 support")
Signed-off-by: Karl Palsson <karlp@etactica.com>
[commit description/subject facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In the rare event a pre-populated fw_env.config exists in the rootfs prior
to firstboot, calling fw_setenv after the system has initialised will
annihilate the devices environment due to two identical lines in
fw_env.config.
Check for existence prior to blind appendage.
Signed-off-by: Imran Khan <gururug@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: fixed patch format, improved grep, cosmetics]
Hardware:
Allwinner H3 upto 1.2GHz
512MB DDR3 RAM
8GB on-board eMMC - mountable, can be used as boot with custom boot.scr
microSD-card slot
WiFi 802.11n (AP6212A) - working
Bluetooth (AP6212A) - not working for now
Micro-USB OTG + 2*USB headers
UART 3.3V - working
GPIO/I2C/SPI 2.54mm headers
Standard sunxi SD-card installation procedure - copy image to SD card,
insert in into slot and boot. First time you will need UART adapter to
enable on-board wireless (or just build custom image with enabled WiFi).
To boot from eMMC:
- boot from SD
- copy SD image to emmc (dd bs=... if=.... of=/dev/mmcblk2)
- mount eMMC boot partition and replace boot script on it
- unmount, reboot
To use i2c, spi and more uarts - replace dtb on boot partition with
fixed one (use dtc or fdt-tools).
Signed-off-by: Roman Bazalevsky <rvb@rvb.name>
[rebase onto device name consolidation patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This changes device definition to resemble the vendor_device scheme
already present for the majority of device compatible strings.
By doing this, we achieve several advantages at once:
- Image names and node names are more consistent with other targets.
- SUPPORTED_DEVICES can be set automatically for all but two cases.
- Image names and node names are in line with DEVICE_TITLEs.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* add u-boot support for uDPU
* add line to copy u-boot binary to STAGING_DIR_IMAGE, this can later be used
as BL33 variable required for ATF build
* add patch to increase max gunzip size in mvebu_armada-37xx.h which is
required for booting the itb recovery images
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
ATF mvebu is required for building a functional bootloader for A7K/A8K and
A37xx platforms. uDPU device is added as the first target.
A3700 platform has a wide range of settings which can be used per device, so
options are defined under the Device sections.
Platform also required WTP (recovery) tools and mv-ddr package for the DDR
topology configuration. 32-bit cross compiler is used for building the WTMI
image.
After the build, flash-image.bin can be used with the bubt command from the
u-boot shell to flash the new version of u-boot.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
All patches have been dropped, they're either redundant (e.g. due to the
new and unset CONFIG_SPL_FAT_WRITE), break compilation (thumb hacks) or
have been applied upstream.
The defconfig for am335x_boneblack has been removed upstream [0], so use
am335x_evm for boneblack too.
Size changes (before, after, file):
ti_am335x-evm and ti_am335x-bone-black:
79804 110832 MLO
623836 756148 u-boot.img
ti_omap3-beagle:
54148 57708 MLO
496272 665728 u-boot.img
ti_omap4-panda:
39356 40204 MLO
284648 366672 u-boot.img
Tested on boneblack, which has the biggest spl size increase. The beagle and
panda spl sizes seem reasonable to not break booting.
[0] 8fa7f65dd0
Signed-off-by: Andre Heider <a.heider@gmail.com>
The GL.iNet GL-AR750S has been supported by the ar71xx and ath79
platforms with access to its 16 MB NOR flash, but not its 128 MB
SPI NAND flash.
This commit provides support for the NAND through the upstream
SPI-NAND framework.
At this time, the OEM U-Boot appears to only support loading the
kernel from NOR. This configuration is preserved as this time,
with the glinet,gl-ar750s-nand name reserved for a potential,
future, NAND-only boot.
The family of GL-AR750S devices on the ath79 platform now includes:
* glinet,gl-ar750m-nor-nand "nand" target
* glinet,gl-ar750m-nor "nand" target (NAND-aware)
NB: This commit increases the kernel size from 2 MB to 4 MB
"Force-less" sysupgrade is presently supported from the current
versions of following NOR-based firmwre images to the version of
glinet,gl-ar750s-nor firmware produced by this commit:
* glinet,gl-ar750s -- OpenWrt 19.07 ar71xx
* glinet,gl-ar750s -- OpenWrt 19.07 ath79
Users who have sucessfully upgraded to glinet,gl-ar750m-nor may then
flash glinet,gl-ar750m-nor-nand with sysupgrade to transtion to the
NAND-based variant.
Other upgrades to these images, including directly to the NAND-based
glinet,gl-ar750s-nor-nand firmware, can be accomplished through U-Boot.
NB: See "ath79: restrict GL-AR750S kernel build-size to 2 MB" which
enables flashing of NAND factory.img with the current GL-iNet U-Boot,
"U-Boot 1.1.4-gcf378d80-dirty (Aug 16 2018 - 07:51:15)"
The GL-AR750S OEM U-Boot allows upload and flashing of either NOR
firmware (sysupgrade.bin) or NAND firmware (factory.img) through its
HTTP-based GUI. Serial connectivity is not required.
The glinet,gl-ar750s-nor and glinet,gl-ar750s-nor-nand images
generated after this commit flash each other directly.
This commit changes the control of the USB VBUS to gpio-hog from
regulator-fixed introduced by commit 0f6b944c92. This reduces the
compressed kernel size by ~14 kB, with no apparent loss of
functionality. No other ath79-nand boards are using regulator-fixed
at this time.
Note: mtd_get_mac_binary art 0x5006 does not return the proper MAC
and the GL.iNet source indicates that only the 0x0 offset is valid
The ar71xx targets are unmodified.
Cc: Alexander Wördekemper <alexwoerde@web.de>
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
The GL.iNet GL-AR300M series of devices includes variants without NAND
and only the 16 MB NOR flash. These include the GL-AR300M16 and the
GL-AR300M-Lite (already with its own board name).
This board-name addition provides disambiguation from the NAND-bearing
GL-AR300M devices, both for OpenWrt code and for end users.
Kernel and firmware support for NAND and UBI will add ~320 kB to the
overall firmware size at this time. This NOR-only option continues to
provide more compact firmware for both the GL-AR300M16 as well as
those who wish to use it as an alternate or primary, NOR-resident
firmware on the GL-AR300M.
The ar71xx targets are unmodified.
Installation
------------
Install through OEM U-Boot (HTTP-based) or `sysupgrade --force` when
booted from NOR and running OEM or OpenWrt, NOR-based firmware.
As one of the intentions is disambiguation from NAND-bearing units,
users who have flashed this firmware onto a device with NAND would
need to use U-Boot or `sysupgrade --force` to flash firmware that
again supports NAND.
There are no additional SUPPORTED_DEVICES as it is not possible to
determine if a device does or does not have NAND based on
either the OEM's or OpenWrt's board names prior to this patch.
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Forward the OpenWrt TARGET_LDFLAGS to the linker of the fw_printenv tool.
In addition also use the more standard make invocation script.
With this change the fw_printenv tool is built with PIE and Full RELRO
support when activated globally in OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
Also update the U-Boot BSP patch for I2SE Duckbill devices.
Run tested on I2SE Duckbill and Olimex OLinuXino Maxi boards.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
This patch adds ath79 support for Netgear WNR2200.
Router was previously supported by ar71xx target only (8 MiB variant).
Netgear WNR2200 has two flash versions - 8MiB sold in EU, US etc. and
16 MiB for Russia and China markets. Apart from flash size both variants
share the same hardware specification.
Specification
=============
* Description: Netgear WNR2200
* Loader: U-boot
* SOC: Atheros AR7241 (360 MHz)
* RAM: 64 MiB
* Flash: 8 MiB or 16 MiB (SPI NOR)
- U-boot binary: 256 KiB
- U-boot environment: 64 KiB
- Firmware: 7808 KiB or 16000 KiB
- ART: 64 KiB
* Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
* Wireless: 2.4 GHz b/g/n (Atheros AR9287)
* USB: yes, 1 x USB 2.0
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN (blue)
- 4 x LAN (amber/green)
- WPS (green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 1.5A
* MAC addresses: LAN on case label, WAN +1, WLAN +2
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_generic=y
CONFIG_TARGET_ath79_generic_DEVICE_netgear_wnr2200-8m=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
CONFIG_KERNEL_DEBUG_INFO=y
CONFIG_KERNEL_DEBUG_KERNEL=y
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Hardware
--------
SoC: Qualcomm IPQ4019
RAM: 256M DDR3
FLASH: 128M NAND
WiFi: 2T2R IPQ4019 bgn
2T2R IPQ4019 a/n/ac
ETH: Atheros AR8033 RGMII PHY
BTN: 1x Connect (WPS)
LED: Power (green/red/yellow)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz1200'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz1200.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ1200.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz1200.bin uboot0
> mtd write /path/to/uboot-fritz1200.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
f92be9d add support for AVM FRITZ!Repeater 1200
d651302 enable support for Atheros AR8033 PHY
e4c857c add machtype override hack
Signed-off-by: David Bauer <mail@david-bauer.net>
Erasesize doesn't belong in the u-boot env config for block devices as it is
known to be 512 byte aligned.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
572ff7f fritzcreator: actually add checksum spacer
6edce1a fritzcreator: replace obscure padding generation with something more portable
2ff189f add ASUS RT-AC58U "easy install" factory u-boot shim
b91f9c2 readd spi-nand support
486ae53 improve cmd_sysupgrade
b0933f1 replace sstrip with strip
882e48a do not include generated files into git
0c5aa5f fix bugs in ipq40xx_cdp.c
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds sysupgrade, uboot-env and networking support
for Methode uDPU device.
Device features 4 partitions:
-----------------------------------------
| boot | recovery | rootfs | misc |
| (ext4) | (ext4) | (fsf2) | (f2fs) |
_________________________________________
Idea was to use f2fs only but the u-boot currently lacks support
so first 2 partition are ext4 to be u-boot readable, and this was
a reason why custom build and sysupgrade sections were required.
On the sysupgrade, boot and rootfs partitions are updated, firmare
image and user configuration is saved on the misc partition and if
the upgrade was successfull, recovery partition will be updated on
after the reboot from preinit script. If the sysupgrade fails for any
reason, device will fallback to recovery initramfs image.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
This changes the default PKG_BUILD_DIR to take BUILD_VARIANT into
account (if set), so that packages do not need to manually override
PKG_BUILD_DIR just to handle variants.
This also updates most base packages with variants to use the updated
default PKG_BUILD_DIR.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
- make create_pbl and byte_swap as host tools
- fix a bug that maybe use the cross compiler
to compile create_pbl and byte_swap:
# -a option appends the image for Chassis 3 devices in case of non secure boot
aarch64-openwrt-linux-musl-gcc -Wall -Werror -pedantic -std=c99 -O2
-DVERSION=v1.5(release):reboot-10604-ge9216b3336 -D_GNU_SOURCE -D_XOPEN_SOURCE=700
-c -o create_pbl.o create_pbl.c
cc1: note: someone does not honour COPTS correctly, passed 0 times
LD create_pbl
/usr/bin/ld: create_pbl.o: Relocations in generic ELF (EM: 183)
/usr/bin/ld: create_pbl.o: Relocations in generic ELF (EM: 183)
/usr/bin/ld: create_pbl.o: Relocations in generic ELF (EM: 183)
create_pbl.o: error adding symbols: File in wrong format
collect2: error: ld returned 1 exit status
Makefile:43: recipe for target create_pbl failed
make[4]: *** [create_pbl] Error 1
plat/nxp/tools/pbl_ch2.mk:45: recipe for target pbl failed
make[3]: *** [pbl] Error 2
- add tfa- prefix to all tools in order to avoid future clashes with
other toolnames
Signed-off-by: Biwen Li <biwen.li@nxp.com>
[added missing HOST_CFLAGS, added tfa- prefix to the tools]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
fiptool is a host tool, used in a firmware generation pipeline, but it's
not treated as such, leading to the build breakage on the hosts which
don't have {Open,Libre}SSL dev package installed:
In file included from fiptool.h:16:0,
from fiptool.c:19:
fiptool_platform.h:18:27: fatal error: openssl/sha.h:
No such file or directory
# include <openssl/sha.h>
So this patch promotes fiptool into the host tool with proper host
include and library paths under STAGING_DIR.
Ref: https://github.com/openwrt/openwrt/pull/2267
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Specifications:
- SoC: AR9344
- RAM: 128MB
- Flash: 2 * 16MB (MX25L12845)
- Ethernet: 2 * FE LAN & 1 * FE WAN
- WiFi: 2.4G: AR9344 5G: QCA9882
Flash instruction:
1. Hold reset and power up the router
2. Set your IP to 192.168.1.x
3. Open 192.168.1.1 and upload the generated *factory* firmware
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Some devices and packages require newer version of u-boot to work
properly, update u-boot to keep up with 4.19 kernel.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
[re-added missing commit message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch is in a series to allow additional STOP indexes after umount,
so that other block devices may stop cleanly.
kdumpinit is now STOP=90
Signed-off-by: Joseph Tingiris <joseph.tingiris@gmail.com>
After commit e82a4d9cfb ("config: regenerate *_shipped sources") the mconf
parser became more strict as a side effect and started to spew a series of
warnings when evaluating our generated kconfig sources:
tmp/.config-package.in:705:warning: ignoring unsupported character '@'
The root cause of these warnings is a wrong use of the @SYMBOL dependency
syntax in various Makefile. Fix the corresponding Makefiles by turning
`@SYM||@SYM2` expressions into the proper `@(SYM||SYM2)` form.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When targets for multiple ESPRESSObin devices were added, not all
files were updated which means any ESPRESSObin version beside generic
won't have proper networking, sysupgrade and uboot-env. This patch
fixes the issue.
* fixup network detection
* fixup uboot-env
* fixup platform.sh for sysupgrade
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Current latest LSDK-19.03 u-boot had a bug that bootcmd
environment was always been reset when u-boot started up.
This was found on boards with spi NOR boot. Before the
proper fix-up is applied, we have to use a workaround
to hard code the bootcmd for OpenWrt booting for now.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to convert to use TF-A for firmware.
- Use un-swapped rcw since swapping will be done in TF-A.
- Use u-boot with TF-A defconfig.
- Rework memory map for TF-A introduction.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Add TF-A packages for Layerscape to implement trusted firmware.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Instead of maintaining 3 very similar subtargets merge them into one.
This does not use the Arm NEON extension any more, because the SAMA5D3
does not support NEON.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com>
This adds the host staging directory to the include path to make it use
the zlib.h files from the staging include directory and also link
against the zlib version from the staging directory.
This fixes a compile problem when the zlib header were not installed on
the build host.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[picked from openwrt-18.06]
Specification:
- Qualcomm Atheros SoC QCA9558
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100/1000 Mbps Ethernet
- 3T3R 2.4 GHz (QCA9558 WMAC)
- 3T3R 5.8 Ghz (QCA9880-BR4A, Senao PCE4553AH)
https://fccid.io/A8J-ECB1750
Tested and working:
- lan, wireless, leds, sysupgrade (tftp)
Flash instructions:
1.) tftp recovery
- use a 1GbE switch or direct attached 1GbE link
- setup client ip address 192.168.1.10 and start tftpd
- save "openwrt-ath79-generic-engenius_ecb1750-initramfs-kernel.bin" as "ap.bin" in tfpd root directory
- plugin powercord and hold reset button 10secs.. "ap.bin" will be downloaded and executed
- afterwards login via ssh and do a sysuprade
2.) oem webinterface factory install (not tested)
Use normal webinterface upgrade page und select "openwrt-ath79-generic-engenius_ecb1750-squashfs-factory.bin".
3.) oem webinterface command injection
OEM Firmware already running OpenWrt (Attitude Adjustment 12.09).
Use OEM webinterface and command injection. See wiki for details.
https://openwrt.org/toh/engenius/engenius_ecb1750_1
Signed-off-by: sven friedmann <sf.openwrt@okay.ms>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[use interrupt-driven "gpio-keys" binding]
The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three,
independent radios. NAND provides two, alternate kernel/firmware
images with fail-over provided by the OEM U-Boot.
Installation:
"Factory" images may be installed directly through the OEM GUI.
Hardware Highlights:
* IPQ4019 at 717 MHz (4 CPUs)
* 256 MB NAND (Winbond W29N02GV, 8-bit parallel)
* 256 MB RAM
* Three, fully-functional radios; `iw phy` reports (FCC/US, -CT):
* 2.4 GHz radio at 30 dBm
* 5 GHz radio on ch. 36-64 at 23 dBm
* 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm
#{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1
* All two-stream, MCS 0-9
* 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights
* USB3, single port on rear with LED
* WPS and reset buttons
* Four status lights on top
* Serial pads internal (unpopulated)
"Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1"
Implementation Notes:
The OEM flash layout is preserved at this time with 3 MB kernel and
~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and
syscfg (56 MB) partitions are untouched, available as read-only.
Serial Connectivity:
Serial connectivity is *not* required to flash.
Serial may be accessed by opening the device and connecting
a 3.3-V adapter using 115200, 8n1. U-Boot access is good,
including the ability to load images over TFTP and
either run or flash them.
Looking at the top of the board, from the front of the unit,
J3 can be found on the right edge of the board, near the rear
|
J3 |
|-| |
|O| | (3.3V seen, open-circuit)
|O| | TXD
|O| | RXD
|O| |
|O| | GND
|-| |
|
Unimplemented:
* serial1 "ttyQHS0" (serial0 works as console)
* Bluetooth; Qualcomm CSR8811 (potentially conected to serial1)
Other Notes:
https://wikidevi.com/wiki/Linksys_EA8300 states
FCC docs also cover the Linksys EA8250. According to the
RF Test Report BT BR+EDR, "All models are identical except
for the EA8300 supports 256QAM and the EA8250 disable 256QAM."
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
for better identification. Also create SUPPORTED_DEVICES string from it
which corresponds to dts compatible string.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Convert whole target to Device Tree based board detection instead of
identifying devices by dts file name. With this we can drop mvebu.sh
translation script and rely on common method for model detection.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Add vendors in device names and also rename few device names, for easier
identyfying potential firmware to flash. The vendor and device string is
mainly derived from model/compatipble string in dts from particular
device, but since not all devices are well described, some of the renames
follow marketing names.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This version has important change for tegra boards which is reserving
32MB memory for Linux kernel instead of current 16MB.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.
To add this target to OpenWrt again port it to a recent and supported
kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is sold as a dual-band 802.11ac range extender. It has a sliding
switch for Extender mode or Access Point mode, a WPS button, a recessed
Reset button, a hard-power button, and a multitude of LED's, some
multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is
Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may
connect at 115200 bps, 8 data bits, no parity, 1 stop bit.
Specification:
- System-On-Chip: QCA9558
- CPU/Speed: 720 MHz
- Flash-Chip: Winbond 25Q128FVSG
- Flash size: 16 MiB
- RAM: 128 MiB
- Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3
- Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4
- PHY: Atheros AR8035-A
Installation:
If you can get to the stock firmware's firmware upgrade option, just feed
it the factory.img and boot as usual. As an alternative, TFTP the
factory.img to the bootloader.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[whitespace fix in DTS and reorder of make variables]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
We do not need to define an empty Build/Configure since
the default checks for existing ./configure and does nothing
in case nothing is found.
Similar for Build/Compile: we can remove the definition
when we only call the default.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Add U-Boot for NVIDIA Tegra based boards, with the first being CompuLab
TrimSlice. This is part of initial support for this board.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The PKG_MIRROR_HASH was for some reason wrong.
Fixes: d75db67870 ("uboot-fritz4040: bump version to 2019-03-03")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
- Former "mir3g" board name becomes "xiaomi,mir3g".
- Reorder some entries to maintain alphabetical order.
- Change DTS so status LEDs (yellow/red/blue) mimic
Xiaomi stock firmware: (Section Indicator)
<http://files.xiaomi-mi.co.uk/files/router_pro/router%20PRO%20EN.pdf>
<http://files.xiaomi-mi.co.uk/files/Mi_WiFi_router_3/MiWiFi_router3_EN.pdf>
|Yellow: Update (LED flickering), the launch of the system (steady light);
|Blue: during normal operation (steady light);
|Red: Safe mode (display flicker), system failure (steady light);
Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
[Added link to similar Router 3 model]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M (NANYA NT5CC128M16JR-EK)
FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI)
ETH: Qualcomm QCA8072
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
WiFi5: QCA9984 4T4R 4SS n/ac
LED: - Connect green/blue/red
- Power green
BTN: WPS/Connect
UART: 115200n8 3.3V
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz3000'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ3000.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz3000.bin uboot0
> mtd write /path/to/uboot-fritz3000.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware:
CPU: MediaTek MT7621AT (2x880MHz)
RAM: 512MB DDR3
FLASH: 256MB NAND
WiFi: 2.4GHz 4x4 MT7615 b/g/n (Needs driver, See Issues!)
WiFI: 5GHz 4x4 MT7615 a/n/ac (Needs driver, See Issues!)
USB: 1x 3.0
ETH: 1x WAN 10/100/1000 3x LAN 10/100/1000
LED: Power/Status
BTN: RESET
UART: 115200 8n1
Partition layout and boot:
Stock Xiaomi firmware has the MTD split into (among others)
- kernel0 (@0x200000)
- kernel1 (@0x600000)
- rootfs0
- rootfs1
- overlay (ubi)
Xiaomi uboot expects to find kernels at 0x200000 & 0x600000
referred to as system 1 & system 2 respectively.
a kernel is considered suitable for handing control over
if its linux magic number exists & uImage CRC are correct.
If either of those conditions fail, a matching sys'n'_fail flag
is set in uboot env & a restart performed in the hope that the
alternate kernel is okay.
If neither kernel checksums ok and both are marked failed, system 2
is booted anyway.
Note uboot's tftp flash install writes the transferred
image to both kernel partitions.
Installation:
Similar to the Xiaomi MIR3G, we keep stock Xiaomi firmware in
kernel0 for ease of recovery, and install OpenWRT into kernel1 and
after.
The installation file for OpenWRT is a *squashfs-factory.bin file that
contains the kernel and a ubi partition. This is flashed as follows:
nvram set flag_try_sys1_failed=1
nvram set flag_try_sys2_failed=0
nvram commit
dd if=factory.bin bs=1M count=4 | mtd write - kernel1
dd if=factory.bin bs=1M skip=4 | mtd write - rootfs0
reboot
Reverting to stock:
The part of stock firmware we've kept in kernel0 allows us to run stock
recovery, which will re-flash stock firmware from a *.bin file on a USB.
For this we do the following:
fw_setenv flag_try_sys1_failed 0
fw_setenv flag_try_sys2_failed 1
reboot
After reboot the LED status light will blink red, at which point pressing
the 'reset' button will cause stock firmware to be installed from USB.
Issues:
OpenWRT currently does not have support for the MT7615 wifi chips. There is
ongoing work to add mt7615 support to the open source mt76 driver. Until that
support is in place, there are closed-source kernel modules that can be used.
See: https://forum.openwrt.org/t/support-for-xiaomi-wifi-r3p-pro/20290/170
Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[02_network remaps, Added link to notes]
Hardware
--------
SOC: QCA9558
RAM: 128M DDR2
Flash: 16MiB SPI-NOR
ETH: QCA8337N: 2x 10/100/1000 PoE and PoE pass-through
WiFi2: QCA9558 (bgn) 2T2R
WiFi5: 2x mPCIE with AR9582 (an) 2T2R
BTN: 1x Reset
GPIO: multiple GPIO on header, PoE passthrough enable
UART: 3.3V 115200 8N1 header on the board
WDG: ATTiny13 watchdog
JTAG: header on the board
USB: 1x connector and 1x header on the board
PoE: 10-32V input in ETH port 1, passthrough in port 2
mPCIE: 2x populated with radios (but replaceable)
OpenWrt is preinstalled from factory. To install use <your-image>-sysupgade.bin
using the web interface or with sysupgrade -n.
Flash from bootloader (in case failsafe does not work)
1. Connect the LibreRouter with a serial adapter (TTL voltage) to the UART
header in the board.
2. Connect an ETH cable and configure static ip addres 192.168.1.10/24
3. Turn on the device and stop the bootloader sending any key through the serial
interface.
4. Use a TFTP server to serve <your image>-sysupgrade.bin file.
5. Execute the following commands at the bootloader prompt:
ath> tftp 82000000 <your image>-sysupgrade.bin
ath> erase 0x9f050000 +$filesize
ath> cp.b 0x82000000 0x9f050000 $filesize
ath> bootm 0x9f050000
More docs
* Bootloader https://github.com/librerouterorg/u-boot
* Board details (schematics, gerbers): https://github.com/librerouterorg/board
Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
Use tested values on shuttle,kd20 and assumed values for
mitrastar,stg-212 and cloudengines,pogoplug*.
akitio users have yet to report back stock flash layout to support
vendor bootloader environment there as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M
FLASH: 128M NAND
ETH: QCA8075
VDSL: Intel/Lantiq VRX518 PCIe attached
currently not supported
DECT: Dialog SC14448
currently not supported
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
LED: - Power/DSL green
- WLAN green
- FON/DECT green
- Connect/WPS green
- Info green
- Info red
BTN: - WLAN
- FON
- WPS/Connect
UART: 115200n8 3.3V (located under the Dialog chip)
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz7530'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ7530.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz7530.bin uboot0
> mtd write /path/to/uboot-fritz7530.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
[removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Adds support for the AVM FRITZ!Box 7530.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [PKG_RELEASE]
VBoxManage is not used and the image is created with proper permisions:
0f5d0f6 image: use internal qemu-img for vmdk and vdi images drop host
dependencies on qemu-utils and VirtualBox
Unreachable config symbols:
9e0759e x86: merge all geode based subtargets into one
No need to define those symbols since x86_64 is subtarget of x86:
196fb76 x86: make x86_64 a subtarget instead of a standalone target
Unreachable config symbols, so remove GRUB_ROOT:
371b382 x86: remove the xen_domu subtarget
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This commit adds support for the Linksys EA6350v3 device in the ipq40xx
target.
This is needed for uboot-envtools to access the environment. Without this
patch, the Linksys EA6350v3 will not be able to access the uboot
environment. As a side effect, the feature auto_recovery will make the
device unstable by switching between the latest and the current firmware.
Signed-off-by: Ryan Pannell <ryan@osukl.com>
Signed-off-by: Oever González <notengobattery@gmail.com>
CPU: FSL P1020 (2x 800MHz E500 PPC)
RAM: 1GB DDR3
FLASH: 256MiB NAND
WiFi: 2x Atheros AR9382 2x2:2 abgn
ETH: 2x BCM54616S - 1x BCM53128 8-port switch
LED: 5x LEDs (Power, WiFi1, WiFi2, N/D, SYS)
BTN: 1x RESET
Installation
------------
1. Download initrams kernel image, dtb binary and sysupgrade image.
2. Place initramfs kernel into tftp root directory. Rename to
"panda-uimage-factory".
3. Place dtb binary into tftp root directory. Rename to "panda.fdt".
4. Start tftp server on 192.168.100.8/24.
5. Power up the device with the reset button pressed. It will download
the initrams and dtb via tftp and boot into OpenWRT in RAM.
6. SSH into the device and remove the factory partitions.
> ubirmvol /dev/ubi0 --name=kernel1
> ubirmvol /dev/ubi0 --name=rootfs1
> ubirmvol /dev/ubi0 --name=devicetree1
You will have around 60 MiB of free space with that.
You can also delete "kernel2", "devicetree2", "rootfs2" and "storage"
respectively in case you do not want to go back to the vendor firmware.
7. Modify the U-Boot bootcmd to allow for booting OpenWRT
> fw_setenv bootcmd_owrt "ubi part ubi && ubi read 0x1000000 kernel
&& bootm 0x1000000"
> fw_setenv bootargs_owrt "setenv bootargs console=ttyS0,115200
ubi.mtd=3,2048"
> fw_setenv bootcmd "run bootargs_owrt; run bootcmd_owrt"
8. Transfer the sysupgrade image via scp into the /tmp directory.
9. Upgrade the device
> sysupgrade -n /tmp/<imagename>
Signed-off-by: David Bauer <mail@david-bauer.net>
On musl based distributions, u-boot 2010.03 fails to build with:
u-boot-2010.03/include/u-boot/crc.h:29:50: error: unknown type name 'uint'
uint32_t crc32 (uint32_t, const unsigned char *, uint);
The issue was fixed in the newer u-boot-2018.03 version, this commit
backports the change to the older version used by ar71xx/ath79.
Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com>
[add commit message from PR description]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The Detection pin is at PF6 and not at PH13 like defined before. I
checked the schematics and now I am am not seeing this error message any
more:
Loading Environment from FAT... Card did not respond to voltage select!
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Disable the PMIC on Olimex A13 Olinuxino, as the SPL cannot set the
core voltage correctly, which causes the board to freeze later at
kernel if CPU throttling is enabled (see below). This will almost
certainly kill the VGA output (which requires LDO3 to be set), but
this is still a better option than to disable CPU throttling for
all Cortex-A8 based devices.
[ 2.485632] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 384000 KHz
[ 2.525698] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 432000 KHz
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Instead of using a fork of the ARM trusted firmware specifically for the
Allwinner SoCs, use the official version from ARM now, this version
supports the Allwinner SoCs now and the older ATF repository is
deprecated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This updates the uboot for the sunxi target to version 2018.11
The removed patches are applied upstream and not needed any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Copy U-Boot to STAGING_DIR_IMAGE (and append it to the EVA-image from
there) to fix image generation using the image-builder.
Also remove the bootloader from DEVICE_PACKAGES and instead use the
BUILD_DEVICES directive from within the U-Boot makefile.
This fixes eva-image generation using the OpenWRT image-builder.
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds the nescessary settings to allow reading the uboot environment variables on the GL.iNet GL-B1300 board.
Signed-off-by: Ibrahim Tachijian <barhom@netsat.se>
This device is called GL-AR300M, therefore rename the board(s)
to 'gl-ar300m-nor' and 'gl-ar300m-nand'
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
[change boardname in uboot envtools as well, don't use wildcards for
boardname]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The LS1021A-IoT gateway reference design based on the
QorIQ LS1021A processor is a purpose-built, small
footprint hardware platform with a wide array of
high-speed connectivity and low-speed serial interfaces
to support secure delivery of IoT services for home,
business or other commercial location.
- Combines standards-based, open source software with a
feature-rich IoT gateway design to establish a common,
open framework for secured IoT service delivery and
management.
- Provides a wide assortment of high-speed and serial-based
connectivity in a compact, highly secure design.
- High efficiency through the use of the Arm-based QorIQ
LS1021A embedded processor.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
After changing board names to DT compat string, we also need to
adjust the script which generates uboot-env configuration files.
Fixes: e880a30549 ("mxs: use generic sysinfo board detection")
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
According to https://github.com/openwrt/openwrt/pull/1527, support
for the Buffalo BHR-4GRV2 in ath79 requires repartitioning from
an initramfs image, make this easier by supporting uboot-envtools
support out of the box.
Build tested, but not runtime tested.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Port support for the Buffalo WZR-HP-AG300H from the ar71xx target to
ath79 as well.
Build- and runtime tested on the Buffalo WZR-HP-AG300H.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Beside one exception, no one took care of these two remaining boards
still using the legacy image build code during the last two years.
Since OpenWrt 14.07 the ALLNET ALL0239-3G image building is broken.
The Sitecom WL-341 v3 image build code looks pretty hackish and broken.
It's questionable if the legacy image works as all.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch updates the uboot-fritz4040 package to the latest version.
The portability and private-libgcc patches, as well as the
upload-to-f4040.sh script have been added to the upstream repository.
Furthermore, the upload-to-f4040 has been updated to take the first
parameter as the file it is supposed to flash, otherwise it defaults
to the previous "uboot-fritz4040.bin". Furthermore the error messages
have been improved and ftp will now dump some "progress information"
to the user's console.
Also included is support for gcc 8+ and a fix for the obnoxous error
that currently breaks the builders:
| fritz/src/lzma2eva.c:23:30: fatal error: zlib.h: No such file or directory
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for the Netgear WNDAP620 and WNDAP660,
they are similar devices, but due to the LAN LED configuration,
the switch setup and WIFI configuration each gets a different
device target.
Hardware Highlights WNDAP620:
CPU: AMCC PowerPC APM82181 at 1000 MHz
DRAM: 128 MB, 2 x 64 MiB DDR2 Hynix H5PS5162GF
CPU: AMCC PowerPC APM82181 at 1000 MHz
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY - Only 1 GBit Port (POE)
Wifi: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 3 internal dual-band antennae + 3 x RSMA for external antennaes
Hardware Highlights WNDAP660:
CPU: AMCC PowerPC APM82181 at 1000 MHz + 2 Heatsinks
DRAM: 256 MB, 2 x 128 MiB DDR2
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY (POE)
Wifi1: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Wifi2: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, 2x dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 6 internal dual-band antennae + 3 x RSMA for external antennaes
Flashing requirements:
- needs a tftp server at 192.168.1.10/serverip.
- special 8P8C(aka RJ45)<->D-SUB9 Console Cable
("Cisco Console Cable"). Note: Both WNDAP6x0 have
a MAX3232 transceivers, hence no need for any separate
CMOS/TTL level shifters.
External Antenna:
The antennae mux is controlled by GPIO 11 and GPIO14. Valid Configurations:
= Config# = | = GPIO 11 = | = GPIO 14 = | ===== Description =====
1. | 1 / High | 0 / Low | Use the internal antennae (default)
2. | 0 / Low | 1 / High | Use the external antennae
The external antennaes are only meant for the 2.4 GHz band.
One-way Flashing instructions via u-boot:
0. connect the serial cable to the RJ45 Console Port
Note: This requires a poper RS232 and not a TTL/USB adaptor.
1. power up the AP and interrupt the u-boot process at
'Hit any key to stop autoboot'
2. setup serverip and ipaddr env settings
Enter the following commands into the u-boot shell
# setenv ipaddr 192.168.1.1
# setenv serverip 192.168.1.10
3. download the factory.img image to the AP
Enter the following commands into the u-boot shell
# tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-squashfs-factory.img
4. verfiy image integrity
Enter the following commands into the u-boot shell
# crc32 $fileaddr $filesize
If the calculated crc32 checksum does not match, go back to step 3.
5. flash the image
Enter the following commands into the u-boot shell
# nand erase 0x110000 0x1bd0000
# nand write ${kernel_addr_r} 0x110000 ${filesize}
6. setup uboot environment
Enter the following commands into the u-boot shell
# setenv bootargs
# setenv fileaddr
# setenv filesize
# setenv addroot 'setenv bootargs ${bootargs} root=/dev/ubiblock0_0'
# setenv owrt_boot 'nboot ${kernel_addr_r} nand0 0x110000; run addroot; run addtty; bootm ${kernel_addr_r}'
# setenv bootcmd 'run owrt_boot'
# saveenv
7. boot
# run bootcmd
Booting initramfs instructions via u-boot:
Follow steps 0 - 2 from above.
3. boot initramfs
Enter the following commands into the u-boot shell
# tftp ${kernel_addr_r} openwrt-apm821xx-nand-netgear_wndap660-initramfs-kernel.bin
# run addtty
# bootm ${kernel_addr_r}
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds u-boot environment access to the MX60(W) target.
"The environment size is one NAND block (128KiB on Buckminster).
We allocate four NAND blocks to deal with bad blocks which may
exist in the saved environment"
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
All apm821xx devices use u-boot and most of them have
an accessible u-boot environment. This patch adds the
necessary template file, but does not add the
uboot-envtools package to any of the targets.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Also update the U-Boot BSP patch for I2SE Duckbill devices
and remove upstreamed patch for LibreSSL support.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
In dtc version 1.4.6 the macro names in header include guards changed,
but the build relies on them matching in order to replace selected
headers. This is a horrible hack to work around this.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
ls1012afrdm was no longer supported in NXP Layerscape SDK.
Instead a new board ls1012afrwy was introduced in LSDK.
This patch is to drop ls1012afrdm and add ls1012afrwy support.
Since only 2MB NOR flash could be used, we just put u-boot
and firmware on NOR flash, and put kernel/dtb/rootfs on SD
card.
The Layerscape FRWY-LS1012A board is an ultra-low-cost
development platform for LS1012A Series Communication
Processors built on Arm Cortex-A53. This tool refines the
FRDM-LS1012A with more features for a better hands-on experience
for IoT, edge computing, and various advanced embedded
applications. Features include easy access to processor I/O,
low-power operation, micro SD card storage, an M2 connector, a
small form factor, and expansion board options via mikroBUS Click
Module. The MicroBUS Module provides easy expansion via hundreds
of powerful modules supporting sensors, actuators, memories,
and displays.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
NOR/QSPI Flash on Layerscape board only has limited 64MB memory size.
Since some boards (ls1043ardb/ls1046ardb/ls1088ardb/ls1021atwr)
could support SD card boot, we added SD boot support for them to put
all things on SD card to meet large memory requirement.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The NXP TWR-LS1021A module is a development system based
on the QorIQ LS1021A processor.
- This feature-rich, high-performance processor module can
be used standalone or as part of an assembled Tower System
development platform.
- Incorporating dual Arm Cortex-A7 cores running up to 1 GHz,
the TWR-LS1021A delivers an outstanding level of performance.
- The TWR-LS1021A offers HDMI, SATA3 and USB3 connectors as
well as a complete Linux software developer's package.
- The module provides a comprehensive level of security that
includes support for secure boot, Trust Architecture and
tamper detection in both standby and active power modes,
safeguarding the device from manufacture to deployment.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to implement u-boot environment txt files
to support OpenWrt boot for all layerscape devices.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The u-boot source code had been migrated to codeaurora
for LSDK-18.06 release and the future release. This
patch is to update u-boot to LSDK-18.06 for both
uboot-layerscape and uboot-layerscape-armv8_32b packages.
Besides, this patch also introduced some other changes.
- Reworked uboot-layerscape makefile to make it more
readable.
- Define package in uboot-layerscape-armv8_32b for each board.
- Fixed u-boot package selection in target image makefile.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Dropped uboot-layerscape patches which were environemnt patches.
We will make u-boot environment binaries with a txt file for all
devices.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The NanoPi NEO2 is a small Allwinner H5 based board available with
different DRAM configurations.
This board is very similar to the NanoPi NEO PLUS2
Signed-off-by: Jasper Scholte <NightNL@outlook.com>
Follow the strategy of other targets and create a
default environment file, uEnv.txt, to configure the
behavior of U-Boot.
For now, use it to pass bootargs to the kernel
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Create a directory inside STAGING_DIR and copy U-Boot
output images, so they can be used later when creating the
sdcard image
Additionally, like others targets, override the default
install method to avoid copying the images to bin directory
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Select the U-Boot variant automatically based on the
current selected device, and hide the package from
menuconfig
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The board was added when creating the target, but the
corresponding device was never defined inside the target
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
- Specifications -
CuBox i1:
- SoC: i.MX6 Solo
- Cores: 1
- Memory Size: 512MB
- GPU: GC880
- Wifi/Bluetooth: Optional
- USB 2.0 ports: 2
- Ethernet: 10/100/1000 Mbps
CuBox i2 | i2eX:
- SoC: i.MX6 Dual Lite
- Cores: 2
- Memory Size: 1GB
- GPU: GC2000
- Wifi/Bluetooth: Optional
- USB 2.0 ports: 2
- Ethernet: 10/100/1000 Mbps
CuBox i4Pro | i4x4:
- SoC: i.MX6 Quad
- Cores: 4
- Memory Size: 2/4 GB
- GPU: GC2000
- Wifi/Bluetooth: Build In
- USB 2.0 ports: 2
- Ethernet: 10/100/1000 Mbps
Built-in u-boot requires SPL (secondary program loader) to be present on the SD-card regardless of the image type which will be loaded.
SPL is generated by the u-boot-mx6cuboxi package which is preselected by the target device and can be found in bin/u-boot-mx6cuboxi directory.
Flashing the SPL:
dd if=/dev/zero of=/dev/mmcblk0 bs=1M count=4
dd if=bin/targets/imx6/generic/u-boot-mx6cuboxi/SPL of=/dev/mmcblk0 bs=1K seek=1
Preparing the firmware on the SD-card:
(echo o; echo n; echo p; echo 1; echo ''; echo ''; echo w) | fdisk /dev/mmcblk0
mkfs.ext4 /dev/mmcblk0p1
mount /dev/mmcblk0p1 /mnt
tar -xzf bin/targets/imx6/generic/openwrt-imx6-device-cubox-i-rootfs.tar.gz -C /mnt/
mkdir -p /mnt/boot
cp bin/targets/imx6/generic/{*-uImage,*.dtb,*.scr} /mnt/boot/
Generated u-boot.img needs to be placed on the first partition:
cp bin/targets/imx6/generic/u-boot-mx6cuboxi/u-boot.img /mnt/
To boot from the SD card:
Boot script which sets mmc/dtb parameters and boots the board is automatically sourced.
If this does not work for any reason:
mmc dev 0; load mmc 0:1 $scriptaddr boot/boot.scr; source $scriptaddr
Currently imx6dl-cubox-i.dtb (Dual Lite) and imx6q-cubox-i.dtb (Quad) device trees are available.
Tested on i4Pro, MMC, USB (+ HiD), HDMI and ethernet ports are working.
Wireless and bluetooth are broken ATM. According to SolidRun forums, BCM4329/BCM4330 firmware is used which works fine on older kernels.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Backport board support from the upcoming v2018.09 release,
and add an additional patch to read the MAC address
from flash memory
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Patch 300-CVE-2015-8370.patch was added without proper rebasing on the
version used by OpenWrt, make it apply and refresh the patch to fix
compilation.
Fixes: 7e73e9128f ("grub2: Fix CVE-2015-8370")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This CVE is a culmination of multiple integer overflow issues that cause
multiple issues like Denial of Service and authentication bypass.
More info: https://nvd.nist.gov/vuln/detail/CVE-2015-8370
Taken from Fedora.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
CPU: H5 High Performance Quad-core 64-bit Cortex-A53
GPU: Mali450 OpenGL ES 2.0/1.1/1.0, OpenVG 1.1, EGL
Memory: 1GB DDR3 (shared with GPU)
Onboard Storage: TF card (Max. 32GB) / NOR flash(2MB)
Onboard Network: 1000M/100M Ethernet RJ45
USB 2.0 Ports: Three USB 2.0 HOST, one USB 2.0 OTG, HOST mode
role by default in DTS
Buttons: Power Button(SW4) Debug TTL
UART: ..DC-IN..
>[GND][RX][TX] ..HDMI..
Signed-off-by: Antonio Silverio <menion@gmail.com>
This adds uci entries for all ath79 devices for which this already was
the case on ar71xx. Additionally we add the OCEDO Koala as there was no
support in OpenWRT yet.
Signed-off-by: David Bauer <mail@david-bauer.net>
* change mx6qsabresd to mx6qsabres to match defconfig name
* merge wanboard profiles since there is only one defconfig for the target device
* move wanboard options from wandboard.h to defconfig
* remove legacy patches
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
With current uboot default configuration the bootloader will
fail to start the OpenWrt firmware with the following error:
-----
unexpected character 'b' at the end of partition
Error initializing mtdparts!
incorrect device type in ubi
Partition ubi not found!
Error, no UBI device/partition selected!
Wrong Image Format for bootm command
Error occured, error code = 112
-----
If the uboot configuration is examined with printenv
I can see that mdtparts line (on a nsa310) is wrong:
-----
mtdparts=mtdparts=orion_nand:0x0c0000(uboot),
0x80000(uboot_env),0x7ec0000(ubi)bootargs_root=
----
The "bootargs_root=" that was appended to it should not be there.
Fix the issue by adding a \0 line terminator at the end of affected lines,
mimicking what is also done by uboot upstream.
This issue was detected and confirmed on a nsa310, nsa325 and
a pogoplug v4, but it's not hardware-specific, so apply the same fix
to other devices as well.
Note that the issue is with the uboot's integrated boot configuration,
which is not used unless the uboot configuration in flash is unavailable
(erased or corrupted), which happens only on first time installation,
or if the user deletes the uboot configuration when upgrading uboot.
People just upgrading from an older uboot without erasing their previous
uboot configuration stored in flash would not have noticed this issue.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
This patch adds support for ZyXEL NBG6617
Hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR: 32 MiB Macronix MX25L25635F
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS
Serial:
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
pre-soldered. Pinout:
1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX
first install / debricking / restore stock:
0. Have a PC running a tftp-server @ 192.168.1.99/24
1. connect the PC to any LAN-Ports
2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
into the tftp-server root directory and rename it to just "ras.bin".
3. power-cycle the router and hold down the the WPS button (for 30sek)
4. Wait (for a long time - the serial console provides some progress
reports. The u-boot says it best: "Please be patient".
5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
flashes fast at the same time. You have to reboot the device and
it should then come right up.
Installation via Web-UI:
0. Connect a PC to the powered-on router. It will assign your PC a
IP-address via DHCP
1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
2. Go to the "Expert Mode"
3. Under "Maintenance", select "Firmware-Upgrade"
4. Upload the OpenWRT factory image
5. Wait for the Device to finish.
It will reboot into OpenWRT without any additional actions needed.
To open the ZyXEL NBG6617:
0. remove the four rubber feet glued on the backside
1. remove the four philips screws and pry open the top cover
(by applying force between the plastic top housing from the
backside/lan-port side)
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6617> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6617>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6617> ATSE NBG6617
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6617> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6617> ATGU
|NBG6617#
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
The device tree files are now matching the kernel 4.17 and this will be
send also for integration into mainline U-Boot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch 220-add-sunxi50i-nanopi-neo-plus2.patch was merged upstream.
The u-boot-sunxi-with-spl.bin is now also created for the ARM64 sunxi
boards by U-Boot itself, no need to do it manually any more.
This was tested on a H2+ Orange Pi R1 and a H5 Orange Pi Zero Plus.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reboot the oxnas target based on Linux 4.14 by rebasing our support on
top of the now-existing upstream kernel support.
This commit brings oxnas support to the level of v4.17 having upstream
drivers for Ethernet, Serial and NAND flash.
Botch up OpenWrt's local drivers for EHCI, SATA and PCIe based on the
new platform code and device-tree.
Re-introduce base-files from old oxnas target which works for now but
needs further clean-up towards generic board support.
Functional issues:
* PCIe won't come up (hence no USB3 on Shuttle KD20)
* I2C bus of Akitio myCloud device is likely not to work (missing
debounce support in new pinctrl driver)
Code-style issues:
* plla/pllb needs further cleanup -- currently their users or writing
into the syscon regmap after acquireling the clk instead of using
defined clk_*_*() functions to setup multipliers and dividors.
* PCIe phy needs its own little driver.
* SATA driver is a monster and should be split into an mfd having
a raidctrl regmap, sata controller, sata ports and sata phy.
Tested on MitraStar STG-212 aka. Medion Akoya MD86xxx and Shuttle KD20.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.
Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.
Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.
Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM
with a different flash layout and boots zImage rather than uImage.
Specification:
- Marvell Armada 385 88F6820 (2x 1.8GHz)
- 256MB of Flash
- 512MB of RAM
- 2.4GHz (bgn) and 5GHz (an+ac wave 2)
- 4x 1Gbps LAN + 1x 1Gbps WAN
- 1x USB 3.0 and 1x USB 2.0/eSATA (combo port)
Flash instruction:
Apply factory image via web-gui.
Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
Add target device as at91-sama5d2_ptc_ek in SAMA5D2 subtarget and
build images for SAMA5D2 PTC Ek board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
reorganizing at91 subtargets based on sama5 soc features and this fix
below problems.
1. able to set neon flags to sama5d2 & sama5d4 subtargets.
2. fix the make clean which removes all the subtargets in bin folder.
3. able to configure kernel specific to subtarget.
4. able to set vfpu4 flags to samad3 subtargets.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
fixed DTC command not found error while compling uboot-at91. The fix
is to set DTC PATH in uboot-at91 MAKE command.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D27 SOM1 with target device as at91-sama5d27_som1_ek
in SAMA5 subtarget and build images for SAMA5D27 SOM1 Ek board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
fetching uboot src from linux4sam/u-boot-at91 github for all at91
target.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
updating to new version v3.8.10 and copying at91bootstrap.bin to bin folder.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Currently, the build system uses an openwrt mirror which does not currently
work and FTP can be unreliable under several circumstances. This change
implicitly allows using all the mirrors to download.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
When libressl was linked the libpthread was missing, add it in addition.
Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When libressl was linked the libpthread was missing, add it in addition.
Also make the mxsimage tool to use the OpenSSL 1.1 API for the recent
libressl version.
Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When libressl was linked the libpthread was missing, add it in addition.
Fixes: 2c192b6916 ("tools/libressl: update to version 2.7.2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Added for convenience. These boards can be used as dev boards running
various operating systems from different media, and this simplifies work
with U-Boot environment.
Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Several changes has been made:
+ AES support has been removed by
upstream commit c6831c7 (2017-11-14)
[remove patch "200-fw_env_no_aes.patch"]
+ Support for UBI volumes has beed added by
upstream commit 34255b9 (2017-11-15)
[remove patch "300-support-env-in-ubivol-chardev.patch"]
+ A command line argument has beed added ("-c") to manually indicate
the location of the environment configuration file
Also, patch "400-u-boot-2015.10-stdint.patch" is no longer
necessary, and the config option to enable UBI support has
been removed.
Size comparisons:
fw_printenv size:
Target Before After
ar71xx 15,189 bytes 18,133 bytes (+2,944 bytes)
ipq40xx 20,873 bytes 20,987 bytes (+114 bytes)
mvebu 20,881 bytes 20,991 bytes (+110 bytes)
ramips 15,128 bytes 18,072 bytes (+2,944 bytes)
OPKG package size:
Target Before After
ar71xx 11,309 bytes 12,875 bytes (+1,566 bytes)
ipq40xx 11,772 bytes 13,299 bytes (+1,527 bytes)
mvebu 11,609 bytes 13,114 bytes (+1,505 bytes)
ramips 10,975 bytes 12,503 bytes (+1,528 bytes)
Compile tested: ipq40xx (musl, glibc, gcc5-musl), ar71xx, mvebu, ramips
Run tested: ipq40xx (ASUS RT-AC58U)
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The serial was working before, but not when doing copy&pasting longer
commands in a short time.
Fixes: a4def18f29 ("uboot-omap: Update to u-boot v2017.01")
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
This release brings various improvements to clearfog support, such as distro-boot.
Obsoletes:
0002-clearfog-reset-usom-onboard-1512-phy.patch
0003-clearfog-enable-distro-boot-code.patch
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
CONFIG_* variables can easily be set by overriding Build/Configure.
so set NET_RANDOM_ETHADDR=y and CMD_SETEXPR=y here.
This replaces the following patches:
0001-clearfog-generate-random-MAC-address.patch
0004-clearfog-enable-setexpr-command-by-default.patch
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
We use the dtc from the kernel and that does not have all the options
which u-boot would like to use now. make these parameters optional.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[wigyori@uid0.hu: renamed to 221-compatible-old-dtc.patch from 220-]
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
U-Boot now requires GCC > 5
Catch up with upstream and move some configuration options from
the header files to the corresponding defconfig files.
Also move some options of patch 010 affecting the whole platform
to 010's device only.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Use the UBOOT_MAKE_FLAGS defined in include/u-boot.mk and do not
overwrite them to compile the host tools against the shipped LibreSSL.
In addition add a patch to fix a compile problem when compiling the
tools against LibreSSL caused by differences in the API between OpenSSL
1.1 and LibreSSL.
This should fix the compile problems seen in build bot from time to time
by not depending on the host libssl-dev package any more but using the
LibreSSL version from OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport the compiler support patches from upstream u-boot to this older
version to make it compile with GCC 7.
This was found by build bot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds support for the Turris Omnia and builds an eMMC sysupgrade image in
the same format as the SolidRun ClearFog.
An initramfs image in the simple yet Omnia-specific 'medkit' image format
is also built in order to ease the initial flashing process.
Notable hardware support omissions are support for switching between SFP
cage and copper PHY, and RGB LED control.
Due to a current limitation of DSA, only 1/2 CPU switch uplinks are used.
Specifications:
- Marvell Armada 385 1.6GHz dual-core ARMv7 CPU
- 1GB DDR3 RAM
- 8GB eMMC Flash
- 5x Gigabit LAN via Marvell 88E6176 Switch (2x RGMII CPU ports)
- 1x switchable RJ45 (88E1514 PHY) / SFP SGMII WAN
- 2x USB 3.0
- 12x dimmable RGB LEDs controlled by independent MCU
- 3x Mini PCIe slots
- Optional Compex WLE200N2 Mini PCIe AR9287 2x2 802.11b/g/n (2.4GHz)
- Optional Compex WLE900VX Mini PCIe QCA9880 3x3 802.11ac (2.4 / 5GHz)
- Optional Quectel EC20 Mini PCIe LTE modem
Flash instructions:
If the U-Boot environment has been modified previously (likely manually via
serial console), first use serial to reset the default environment.
=> env default -a
=> saveenv
Method 1 - USB 'medkit' image w/o serial
- Copy openwrt-mvebu-turris-omnia-sysupgrade.img.gz and
omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz to the root of a
USB flash drive formatted with FAT32 / ext2/3/4 / btrfs / XFS.
Note that the medkit MUST be named omnia-medkit*.tar.gz
- Disconnect other USB devices from the Omnia and connect the flash drive
to either USB port.
- Power on the Omnia and hold down the rear reset button until 4 LEDs are
illuminated, then release.
- Wait approximately 2 minutes for the Turris Omnia to flash itself with
the temporary image, during which LEDs will change multiple times.
- Connect a computer to a LAN port of the Turris Omnia with a DHCP client
- (if necessary) ssh-keygen -R 192.168.1.1
- ssh root@192.168.1.1
$ mount /dev/sda1 /mnt
$ sysupgrade /mnt/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself and you can remove the flash drive.
Method 2 - TFTP w/ serial
- Extract omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz and copy
dtb + zImage to your TFTP server (rename if desired)
- Connect Turris Omnia WAN port to DHCP-enabled network with TFTP server
- Connect serial console and interrupt U-Boot
=> dhcp
=> setenv serverip <tftp_server_ip_here>
=> tftpboot 0x01000000 zImage
=> tftpboot 0x02000000 dtb
=> bootz 0x01000000 - 0x02000000
- OpenWrt will now boot from ramdisk
- Download openwrt-mvebu-turris-omnia-sysupgrade.img.gz to /tmp/
$ sysupgrade /tmp/openwrt-mvebu-turris-omnia-sysupgrade.img.gz
- Wait another minute for the final OpenWrt image to be flashed. The Turris
Omnia will reboot itself.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
Rename the gphy firmware to match the name requested by kernel 4.14 and
update the devicetree source files to use the new name.
Update the u-boot lantiq Makefile to be compatible with the new names as
well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This syncs the Orange Pi R1 device tree files with the one from the
upstream kernel and also uses the default configuration from the Orange
Pi Zero.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
EG-200 is a DIN rail mountable device with one ethernet port, wifi,
an RS-485 port, and an internal USB attached uSD card reader.
Two leds, "modbus" and "etactica" are managed by userspace applications
in factory firmware.
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Karl Palsson <karlp@etactica.com>
This prevents passing down the HOSTCC stuff set in u-boot.mk
which results in linking errors against openssl:
tools/mxsimage.o: In function `sb_aes_reinit':
mxsimage.c:(.text+0x202): undefined reference to `EVP_CIPHER_CTX_reset'
tools/mxsimage.o: In function `mxsimage_generate':
mxsimage.c:(.text+0x110d): undefined reference to `EVP_MD_CTX_new'
mxsimage.c:(.text+0x114f): undefined reference to `EVP_MD_CTX_free'
mxsimage.c:(.text+0x11c3): undefined reference to `EVP_MD_CTX_new'
mxsimage.c:(.text+0x1323): undefined reference to `EVP_MD_CTX_free'
mxsimage.c:(.text+0x134a): undefined reference to `EVP_CIPHER_CTX_reset'
tools/mxsimage.o: In function `mxsimage_verify_print_header':
mxsimage.c:(.text+0x23ce): undefined reference to `EVP_MD_CTX_new'
mxsimage.c:(.text+0x242c): undefined reference to `EVP_MD_CTX_new'
mxsimage.c:(.text+0x246b): undefined reference to `EVP_MD_CTX_free'
mxsimage.c:(.text+0x24ef): undefined reference to `EVP_CIPHER_CTX_reset'
mxsimage.c:(.text+0x2e52): undefined reference to `EVP_MD_CTX_free'
collect2: error: ld returned 1 exit status
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
ls1012ardb/ls1012afrdm/ls1046ardb/ls1088ardb firmwares now use ubifs
rootfs. So u-boot env should be set accordingly.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
With no warning, it just looks like the box has hung during boot.
We don't want users resetting it without having captured a crashdump.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
When we provide the HOSTCFLAGS to the U-Boot build it will fail because
it can not find the u-boot provided header files any more.
Just overwrite and not append the package specific configuration on top
of the configuration provided by u-boot.mk.
uboot-fritz4040 is based on U-Boot 2012.07 and this problem is probably
similar to the problem seen with the lantiq and ar71xx u-boot build.
Fixes: df9781a420 ("u-boot,at91bootstrap: fix incorrect HOSTCPPFLAGS variable")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since I have no openssl-dev on my machine, I first
get this error:
```
tools/kwbimage.c:21:10: fatal error: openssl/bn.h: No such file or directory
#include <openssl/bn.h>
```
After removing the UBOOT_MAKE_FLAGS the next error is:
```
tools/kwbimage.c:40:6: error: conflicting types for ‘EVP_MD_CTX_cleanup’
void EVP_MD_CTX_cleanup(EVP_MD_CTX *ctx)
```
After removing the OpenSSL patches the next error is:
```
HOSTLD tools/dumpimage
/usr/bin/ld: cannot find -lssl
/usr/bin/ld: cannot find -lcrypto
collect2: error: ld returned 1 exit status
scripts/Makefile.host:108: recipe for target 'tools/dumpimage' failed
make[5]: *** [tools/dumpimage] Error 1
```
So, the final part is to add the build system's
HOST_LDFLAGS to the UBOOT_MAKE_FLAGS.
(which was done in the previous commit)
Then the image builds.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This would should up as `$$(HOSTCPPFLAGS)` in the host CFLAGS.
```
make --jobserver-fds=3,4 -j -C <openwrt>/build_dir/target-arm_cortex-a8+vfpv3_musl_eabi/u-boot-A10-OLinuXino-Lime/u-boot-2017.07 CROSS_COMPILE=arm-openwrt-linux-muslgnueabi- DTC="<openwrt>/build_dir/target-arm_cortex-a8+vfpv3_musl_eabi/linux-sunxi_cortexa8/linux-4.9.76/scripts/dtc/dtc" HOSTCC="gcc" HOSTCFLAGS='-O2 -I<openwrt>/staging_dir/host/include -I<openwrt>/staging_dir/host/usr/include -I<openwrt>/staging_dir/hostpkg/include -I<openwrt>/staging_dir/target-arm_cortex-a8+vfpv3_musl_eabi/host/include $$(HOSTCPPFLAGS)' HOSTLDFLAGS="" BL31=<openwrt>/staging_dir/target-arm_cortex-a8+vfpv3_musl_eabi/image/bl31.bin
```
And then it would complain with:
```
/bin/sh: 1: HOSTCPPFLAGS: not found
```
Also, HOSTCPPFLAGS does not exist.
The correct var is HOST_CPPFLAGS.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
We use the dtc from the kernel and that does not have all the options
which u-boot would like to use now. make these parameters optional.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- use release build instead of debug to reduce size
- bump to use latest commit in allwinner tree
Tested on Pine64/1G.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree
Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script
Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
These packages are needed to generate the image, better mark them hidden
so we will activate them based on which boards gets build and they will
be activated always when the board which needs then gets build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These packages are needed to generate the image, better mark them hidden
so we will activate them based on which boards gets build and they will
be activated always when the board which needs then gets build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The fixes following problems
1. changing prefix at91bootstrap to AT91bootstrap will fix the default
selection of at91bootstrap for the selected sama5 subtarget.
2. fixed missing default selection of sama5d4 nand flash for the
selected sama5d4 subtarget.
3. corrected at91bootstrap Title name.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
neon and VFPv4 support is added to this target and uboot-at91 build
fails due to TARGET_CFLAGS -mfloat-abi set to hard. as a fix, setting
uboot-at91 CFLAGS -mfloat-abi=soft.
Fixes: 01cc6bd495 ("at91: sama5: activate fpu")
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
add an uboot able to boot a kernel in an ubi partition
This uboot also has a "recovery" feature, before
booting from flash it will try to boot a initramfs
image called "initramfs.bin" from a FAT32-formatted
USB drive connected to the USB 2.0 port.
(u-boot lacks drivers for usb 3.0 controllers)
Just rename the initramfs image and place it on
the usb drive, the uboot will load it.
In case there is no USB drive or no such file
is found, the uboot will boot from internal flash.
The whole check takes less than a second, boot times
are not impacted.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Use <manufacturer>_<modelname> as image name.
Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Build the Seagate GoFlexHome u-boot for the Seagate GoFlexNet as well. The
name clearly indicates that the u-boot can be used for both boards
Build the Zyxel NSA310 u-boot if the NSA310B image is selected.
Signed-off-by: Mathias Kresin <dev@kresin.me>
No image build code for the Guruplug, Sheevaplug and NSA310S exists. Drop
support for the boards for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The git hash was changed for multiple layerscape packages without
changing the version number. The LEDE build system will not download the
packages again if the old version is already there and so some people
and the build bots are using wrong version of some packages. Use
PKG_SOURCE_DATE instead of PKG_VERSION to generate packages with the
date and the first charterers of the git hash. This will change the file
name and make the build system download them again, also if in future
the git hash is changed the file name will change and trigger a new
download.
This should fix a problem spotted by build bot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The LinkIt Smart 7688/LinkIt Smart 7688 Duo are identical beside the
extra ATmega32U4 - accessible via UART - on the the Duo.
Since all relevant hardware is identical, drop the Duo special handling
in userspace.
Signed-off-by: Mathias Kresin <dev@kresin.me>
In commit 2b1ec44dbd ("layerscape: add ls1012afrdm device support")
The git revision and the mirror hash for this package was updated to a
version which includes ls1012afrdm-uboot.bin, but the file name at
dl/uboot-layerscape-armv8_32b-2017.09.tar.xz staid the same. This way
most user did not download the new version but used the old file.
Convert this package to the normal git clone parameters by using
PKG_SOURCE_DATE instated of PKG_VERSION, now the file name in dl also
contains the git hash and should change every time the git hash is
updated.
This should fix a problem spotted by build bot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use <manufacturer>_<modelname> as image name.
Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.
While at it, normalise the image filenames by using only lower case
characters and bin as file extension for sysupgrade images.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the first compatible string as board name in userspace. Add the new
board name as well as the former used board name to the image metadata
to keep compatibilty with already deployed installations.
Don't add the former used boardname for boards which exists only in
master or evaluation boards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The uboot target is named MarsBoard_A10 and it was not build at all.
This fixes a build problem seen by the build bot.
Fixes: 6a3565985f ("sunxi: Added profile for HAOYU Electronics Marsboard A10")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CPE ids helps to tracks CVE in packages.
https://cpe.mitre.org/specification/
Thanks to swalker for CPE to package mapping and
keep tracking CVEs.
Acked-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
My compilation failed because of missing uint.* definitions:
In file included from mtd.h:33:0,
from bootstream.c:35:
BootControlBlocks.h:58:2: error: unknown type name 'uint8_t'
uint8_t m_u8DataSetup;
^
BootControlBlocks.h:59:2: error: unknown type name 'uint8_t'
uint8_t m_u8DataHold;
^
BootControlBlocks.h:60:2: error: unknown type name 'uint8_t'
uint8_t m_u8AddressSetup;
^
BootControlBlocks.h:61:2: error: unknown type name 'uint8_t'
uint8_t m_u8DSAMPLE_TIME;
Adding the header file fixes the problem.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[fold changes into 001-compile.patch]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The QorIQ FRDM-LS1012A Board is an ultra-low-cost
development platform for QorIQ LS1012A Series Network
Processors built on ARM Cortex-A53 processor.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
- H3 @ 1.3 GHz
- 1GiB DDR3
- 10/100Mbps Ethernet
- Realtek RTL8189ETV wifi
- 4 USB 2.0
Difference to the "Orange Pi Plus" is the lack of Gbit ethernet
and lack of onboard flash.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The MarsBoard was a short-lived credit-card sized, extendable board with an Allwinner A10 SoC.
http://linux-sunxi.org/MarsBoard_A10
Signed-off-by: Kayo Phoenix <kayo@illumium.org>
[Forward-ported to new target layout:]
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Upgrade uboot-kirkwood to upstream release 2017.09
Catch up with upstream and move configuration options from
simple defines to Kconfig, as otherwise dependencies would
not be resolved and code would not compile.
Tested-by: Alberto Bursi <alberto.bursi@outlook.it>
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
This backports the upstream commit fixing stale references to
CONFIG_SUNXI_GMAC which have been later replaced by CONFIG_SUN7I_GMAC.
This fixes the designware MAC pinmuxing on e.g: Lamobo R1.
Refresh patches while we are at it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
removed copying of binaries to BIN_DIR during install and using
default/install to install binaries to BIN_DIR folder.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Added sama5 to BUILD_SUBTARGET variable.This will populate at91bootstrap
menu options in bootloader menu only when SAMA5 devices are selected as
SUBTARGET and to avoid showing up this menu when legacy device is
selected as SUBTARGET and fixed typo mistake: sama5d3 -> sama5d2.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
This fixes the following problems:
* Add BUILD_DEVICES for legacy subtarget
* Use features from u-boot.mk for sama5 subtarget This is mainly done
by changing the prefix from uboot to U-Boot. This makes them depend
on the sama5 subtarget and not selectable for the legacy subtarget
any more
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
NXP Layerscape LSDK had set up its own open source web site
and github for release.
https://lsdk.github.iohttps://github.com/qoriq-open-source
This patch is to update rcw/fman_ucode/u-boot packages with LSDK
git trees. Also add some patches of packages to support LEDE.
Since ARMv8 32-bit u-boot images are same with ARMv8 64-bit images
but 64-bit toolchain couldn't be used for 32-bit targets, we still
use a private tree for ARMv8 32-bit u-boot images. This is in plan
to move this private tree to NXP Layerscape github.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Rename subtargets 32b/64b with armv8_32b/armv8_64b which are
more proper, and update makefile files. There also will be other
subtargets added in the future, like armv7.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch implements CPU frequency control as found on several
routerboard devices.
Supported SoCs:
- QCA953X
- AR9344
Tested on hAP lite and mAP lite (QCA953x): steps of 50MHz
Tested on LHG 5 (AR9344): steps of 50MHz
On unsupported hardware, this patch is a NOP: it will not alter the
new field.
"rbcfg help" will display an empty "cpu_freq" help listing.
"rbcfg show" will not show the cpu_freq field.
"rbcfg set/get cpu_freq" will return an error code.
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
[adjusted subject]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The following features are working and tested:
* both Ethernet ports
* MMC
* LED
The following features are not working:
* Wifi (There is a crappy driver we could port)
* SPI flash (I haven't looked into this)
I haven't tried out the rest.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit improves support for the Xiaomi Mi Router 3G originally
added in commit 6e283cdc0d
Improvements:
- Remove software watchdog as hardware watchdog now working as per
commit 3fbf3ab44f for all mt7621
devices.
- Reset button polarity corrected - length of press determines reboot
(short press) vs. reset to defaults (long press) behaviour.
- Enable GPIO amber switch port LEDs on board rear - lit indicates 1Gbit
link and blink on activity. Green LEDs driven directly by switch
indicating any link speed and tx activity.
- USB port power on/off GPIO exposed as 'usbpower'
- Add access to uboot environment settings for checking/setting uboot
boot order preference from user space.
Changes:
- Front LED indicator is physically made of independent Yellow/Amber,
Red & Blue LEDs combined via a plastic 'lightpipe' to a front panel
indicator, hence the colour behaviour is similar to an RGB LED. RGB
LEDs are not supported at this time because they produce colour results
that do not then match colour labels, e.g. enabling 'mir3g:red' and
'mir3g:blue' would result in a purple indicator and we have no such
label for purple.
The yellow, red & blue LEDs have been split out as individual yellow,
red & blue status LEDs, with yellow being the default status LED as
before and with red's WAN and blue's USB default associations removed.
- Swapped order of vlan interfaces (eth0.1 & eth0.2) to match stock vlan
layout. eth0.1 is LAN, eth0.2 is WAN
- Add 'lwlll' vlan layout to mt7530 switch driver to prevent packet
leakage between kernel switch init and uci swconfig
uboot behaviour & system 'recovery'
uboot expects to find bootable kernels at nand addresses 0x200000 &
0x600000 known by uboot as "system 1" and "system 2" respectively.
uboot chooses which system to hand control to based on 3 environment
variables: flag_last_success, flag_try_sys1_failed & flag_try_sys2_failed
last_success represents a preference for a particular system and is set
to 0 for system 1, set to 1 for system 2. last_success is considered *if*
and only if both try_sys'n'_failed flags are 0 (ie. unset) If *either*
failed flags are set then uboot will attempt to hand control to the
non failed system. If both failed flags are set then uboot will check
the uImage CRC of system 1 and hand control to it if ok. If the uImage
CRC of system is not ok, uboot will hand control to system 2
irrespective of system 2's uImage CRC.
NOTE: uboot only ever sets failed flags, it *never* clears them. uboot
sets a system's failed flag if that system's was selected for boot but
the uImage CRC is incorrect.
Fortunately with serial console access, uboot provides the ability to
boot an initramfs image transferred via tftp, similarly an image may
be flashed to nand however it will flash to *both* kernels so a backup
of stock kernel image is suggested. Note that the suggested install
procedure below set's system 1's failed flag (stock) thus uboot ignores
the last_success preference and boots LEDE located in system 2.
Considerable thought has gone into whether LEDE should replace both
kernels, only one (and which one) etc. LEDE kernels do not include a
minimal rootfs and thus unlike the stock kernel cannot include a
method of controlling uboot environment variables in the event of
rootfs mount failure. Similarly uboot fails to provide an external
mechanism for indicating boot system failure.
Installation - from stock.
Installation through telnet/ssh:
- copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and
lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it
from LEDE download site to /tmp
- switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if
wgetted from LEDE download site
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1
- run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0
- run: nvram set flag_try_sys1_failed=1
- run: nvram commit
- run: reboot
Recovery - to stock.
Assuming you used the above installation instructions you will have a
stock kernel image in system 1. If it can be booted then it may be used
to perform a stock firmware recovery, thus erasing LEDE completely. From
a 'working' LEDE state (even failsafe)
Failsafe only:
- run: mount_root
- run: sh /etc/uci-defaults/30_uboot-envtools
Then do the steps for 'All'
All:
- run: fw_setenv flag_try_sys2_failed 1
- run: reboot
The board will reboot into system 1 (stock basic kernel) and wait with
system red light slowly blinking for a FAT formatted usb stick with a
recovery image to be inserted. Press and hold the reset button for
around 1 second. Status LED will turn yellow during recovery and blue
when recovery complete.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Fixes the following build issue: "undefined reference to `EVP_MD_CTX_create'"
From: Jelle van der Waa <jelle@vdwaa.nl>
The rsa_st struct has been made opaque in 1.1.x, add forward compatible
code to access the n, e, d members of rsa_struct.
EVP_MD_CTX_cleanup has been removed in 1.1.x and EVP_MD_CTX_reset should be
called to reinitialise an already created structure.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[replaced u-boot patch with original version from u-boot git]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The arm-trusted-firmware-sunxi package is only used by the Allwinner
A64, so only make it selectable for its subtarget sunxi/cortexa53.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Jonas Gorski <jonas.gorski@gmail.com>
at91bootstrap is a second-level bootloader for Microchip(Atmel AT91) SoCs.
It provides a set of algorithms to manage the hardware initialization and
to download the main application or a third-level bootloader(i.e. uboot)
from specified boot media to main memory and execute it.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D4 Xplained board and options to select & build
u-boot configs for different media storage.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D2 Xplained board and options to select & build
u-boot configs for different media storage.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D3 Xplained board and options to select & build
u-boot configs for different media storage.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
IPQ806x AP148 and DB149 boards didn't have the UCI ubootenv
section initialized, so the usage of fw_printenv required manual
configuration. With this change, the "fw_printenv" and "fw_setenv"
command will automatically work on NOR and NAND based platforms.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Backing up the current firmware from U-Boot over serial can take hours.
Booting a working Linux image for backup purposes is not always an option.
Using the tftpput command in U-Boot is the fastest and easiest way.
tftpput will upload the contents of a memory region to the TFTP server.
The IP address of the server is stored in the serverip variable.
Usage:
tftpput <memaddr> <length> <filename>
Example for a complete flash backup of an o2 Box 6431 (VGV7510KW22):
VGV7510KW22 # tftpput 0xB0000000 0x1000000 o2boxbackup.bin
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
split kexec-tools into two packages, kexec and kdump.
* kexec to simply execute a new kernel
* kdump is for loading and collecting debris of a crashed kernel with
support for kdump forensics.
In order to properly support booting into a crashkernel, an init script
as well as UCI configuration has been added.
As modifying the kernel cmdline is required for this to work in x86
platforms use an uci-defaults script to modify /boot/grub/grub.cfg.
To test collecting crash information, use the 'c' sysrq-trigger, ie.
echo c > /proc/sysrq-trigger
This should result in the crash kernel being executed and (depending
on the configution) dmesg and/or vmcore getting saved.
To check if the crash kernel was loaded properly, use the 'status'
command of the kdump init script.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
EnGenius ENS202EXT is an outdoor wireless access point with
2-port 10/100 switch, detachable antennas and proprietery PoE.
The device is based on Qualcomm/Atheros AR9341 v1.
Specifications:
- 535/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM
- 16 MB of FLASH
- UART (J1) header on PCB (unpopulated)
- 2x 10/100 Mbps Ethernet
- 2.4 GHz, up to 26dBm
- 2x external, detachable antennas
- 7x LED, 1x button
Flash instructions:
You have three options:
- Use the vendor firmware upgrade page on the web interface and give
it the factory.img. This is the easiest way to go about it.
- If you have serial access during u-boot, interrupt the normal boot
(any key before timeout) and run 'run failsafe_boot'; this will bring
you to a minimal openwrt luci image on ip 192.168.1.1 useful if you've
bricked the normal firmware.
- Use the vendor's management cli, which can be accessed via telnet
with the same credentials as the web login (default admin:admin), then
issue the following commands:
*** Hi admin, welcome to use cli(V-1.6.7) ***
---========= Commands Help =========---
stat -- Status
sys -- System
wless2 -- 2.4G-Wireless
mgmt -- Management
tree -- Tree
help -- Help
reboot -- Reboot
ens202ext>mgmt
Management
---========= Commands Help =========---
admin -- Administration
mvlan -- Management VLAN settings
snmp -- SNMP settings
backup -- Backup/Restore settings
autorb -- Auto reboot settings
fwgrade -- Firmware upgrade
time -- Time settings
wifisch -- Wifi schedule
log -- Log
diag -- Diagnostics
disc -- Device Discovery
logout -- Logout
help -- Help
exit -- Exit
ens202ext/mgmt>fwgrade
Management --> Firmware upgrade
---========= Commands Help =========---
fwup -- Firmware upgrade
help -- Help
exit -- Exit
ens202ext/mgmt/fwgrade>fwup http://web.server/lede-ar71xx-generic-ens202ext-squashfs-factory.bin
Signed-off-by: Marty Plummer <ntzrmtthihu777@gmail.com>
Add a patchfile that implements distro-boot and is meant to go upstream
Also make the other patches git-am'able for easier maintenance.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
Add support for SolidRun ClearFog Base board.
The base model is a smaller version of ClearFog Pro without
the DSA switch, replacing it with a second copper gigabit
port, and only one PCIe socket.
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
Even it's unknown if it's booting with thumb, because the lack of hardware.
Enable it for now, so the build succeed, because without thumb it can not fit
into spl.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The beagleboard doesn't boot with Thumb enabled, but without Thumb the
SPL (first stage bootloader) is too big to fit into SRAM.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Use fixed led names and add each board variant instead of manipulating
the board name.
It makes the ramips board name function less different to the one used
in other targets and allows to merge them with a common function.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Couple of important upstream patches (slated for 2.0.15) that
are necessary for kexec to run on MUSL and on x86 hardware.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
With upstream changes, the last update to U-Boot 2017.03
broke the nsa310 and nsa325 targets. Also fix some redefines.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
The Pistachio target is a MIPS interaptiv based SoC developed by
Imagination Technologies. It includes blocks for i2c, spi, audio,
usb and WiFi.
This also adds the base support for the 'Creator Ci40 (marduk)'
device which uses the Pistachio SoC to create an IoT hub by
including Bluetooth, WiFi and 6lowpan on one board. Additionally 2x
Mikrobus ports are available to expand with further RF technologies
or add sensors. You can find out more here http://creatordev.io.
Note, this commit is just the initial board support hence the
following are not expected to work yet:
* WiFi
* Bluetooth
* 6lowpan
* Audio
* Mikrobus uarts, user leds (clock dependency of 6lowpan chip)
The aim of this commit is to essentially have the same level of
support that currently exists in the mainline kernel.
Signed-off-by: Abhijit Mahajani <Abhijit.Mahajani@imgtec.com>
Signed-off-by: Francois Berder <francois.berder@imgtec.com>
Signed-off-by: Ian Pozella <Ian.Pozella@imgtec.com>
Signed-off-by: Mayank Sirotiya <Mayank.Sirotiya@imgtec.com>
Signed-off-by: Sean Kelly <Sean.Kelly@imgtec.com>
Backport kernel patches for LS1043A Rev1.1 support from upstream,
patchwork, and SDK. And update to latest u-boot to support LS1043A
Rev1.1.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This is needed for the definition of $(LINUX_DIR). This is used in
u-boot.mk to change the device-tree compiler to the dtc used by
linux.
Without this, the build will use the system dtc. This results in a
build failure when a dtc does not exist outside the buildroot.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Specifying USE_PRIVATE_LIBGCC is no longer needed, as it is the
default.
Patch 001 is removed, since it was already merged upstream. Patches
100 and 101 are removed because they do not appear to be needed
anymore, and they do not conform with the sign-off and commit message
procedures.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Because they were hidden, there was no way to disable the uboot
targets in menuconfig, so they had to be built every time. The omap
target is the only one to hide uboot packages. To be consistent with
the other targets, and have more control over the build, un-hide the
u-boot packages.
Note that the default behavior remains unchanged, as uboot will be
built unless explicitly disabled.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
fixes issue "nsa 310b u-boot can initialize usb but cannot
use usb storage so it cannot load files from usb"
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Goflexhome/net use uImage, and to boot an uImage the u-boot
must use bootm command, not bootz.
Fixes the "i cannot boot LEDE with this u-boot" issue that I
found out myself with my goflexnet.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
all patches for CONFIG_SYS_GENERIC_BOARD are obsolete for
uboot 2016 sources.
Run-tested with the uboot of goflexnet, also the md5sum of
all other uboots is the same with or without these patches.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Do not put the apex images into the kernel build directory as this directory
might get removed after kernel updates while the apex packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot and ucode images into the kernel build directory as this
directory might get removed after kernel updates while the u-boot packages
InstallDev recipe is not getting re-executed because it is still considered
current, leading to image build failures later on due to missing images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Do not put the u-boot images into the kernel build directory as this directory
might get removed after kernel updates while the u-boot packages InstallDev
recipe is not getting re-executed because it is still considered current,
leading to image build failures later on due to missing u-boot images.
To ensure that built bootloader images persist over kernel version updates in
the buildroot, put them into the new STAGING_DIR_IMAGE directory.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
All SPL variants are lzo compressed. The lzop binary is used for
compression but is not available in tools.
Additionally at least the NAND SPL support is broken and doesn't create
working bootloaders.
The fb3370 SPI NOR SPL enabled u-boot isn't required for LEDE since the
LEDE images are targeting the pre-installed EVA bootloader.
Mark these u-boot variants as well as the SPL variants for the
reference boards as broken till the lzma issues are fixed upstream and
we can use lzma instead of lzo compression.
Signed-off-by: Mathias Kresin <dev@kresin.me>
accessing the u-boot's envs on this device is required to read the mac address.
These are the envs of the new u-boot, not of the stock one.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Instead of referencing u-boot packages from device profiles and having a
-all metapackage, make the u-boot packages hidden (they don't install to
bin/ anyway), and name the files in KERNEL_BUILD_DIR appropriately
Signed-off-by: Felix Fietkau <nbd@nbd.name>
this commit allows to make a standalone u-boot for nsa310b.
While both first-stage and second-stage u-boot work fine if
installed to flash or loaded with kwboot,
I could not get stock u-boot nor bodhi's u-boot to chainload
any second stage u-boot (I also tried with dockstar's uboot
that works fine on this device if loaded with kwboot).
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
While at it, the following changes are introduced
- Rewrite the Makefile for better readability
- Make parallel builds possible
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Increasing CONFIG_SYS_BOOTM_LEN from 8 MB to 16 MB is necessary to
support uncompressing images larger than 8 MB when using the bootm
command.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This seems to occur when gettext-full is built on the host-side
and the autoreconf stuff re-generates some of the build files,
except for the po/Makefile.in.in
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Even though these fonts may not be installed, they seem to be
generated at build time.
Seems that the configure script re-generated from configure.ac
is a bit more annoying than it has to be.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Reboot of: a0ea22ac43
Reverted: 3c52cbfa53
The host-side build of grub2 requires this sometimes.
This will re-generate the ./configure script from configure.ac.
I don't know the conditions of how this reproduces, it just
sometimes appears, and sometimes doesn't.
Build error
```
<lede-dir>/build_dir/target-x86_64_musl-1.1.15_yogi/host/grub-2.02~beta2/build-aux/missing: line 81: aclocal-1.14: command not found
WARNING: 'aclocal-1.14' is missing on your system.
You should only need it if you modified 'acinclude.m4' or
'configure.ac' or m4 files included by 'configure.ac'.
The 'aclocal' program is part of the GNU Automake package:
<http://www.gnu.org/software/automake>
It also requires GNU Autoconf, GNU m4 and Perl in order to run:
<http://www.gnu.org/software/autoconf>
<http://www.gnu.org/software/m4/>
<http://www.perl.org/>
Makefile:3962: recipe for target 'aclocal.m4' failed
```
Adding PKG_FIXUP adds sanity (i.e. autoreconf is used for host & target
builds) over just using HOST_FIXUP.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Few minor code formatting style fixes, including:
- keep one board per line
- always use "|\" (for consistency)
- remove redundant double quotes and empty lines
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Add support for NXP layerscape ls1046ardb 64b/32b Dev board.
LS1046ARDB Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 512 Mbyte NAND flash
* Two 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
* On-board 4G eMMC
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe:
* PCIe1 (SerDes2 Lane0) to miniPCIe slot
* PCIe2 (SerDes2 Lane1) to x2 PCIe slot
* PCIe3 (SerDes2 Lane2) to x4 PCIe slot
* USB 3.0: one super speed USB 3.0 type A port, one Micro-AB port
* UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
In order to prevent the impact of the merger of the company and the potential
rebase of the SDK repositories, migrate the u-boot source to github.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Based on the submission to the uboot-lantiq repo by Martin Blumenstingl.
Use the ddr_settings.h from the GPL tarball. The NAND boot optimized
one (with memory tuning enabled) doesn't work for the UART boot image.
Use the same mtd layout as the stock u-boot. Add add UBI support.
Use the leds to indicate boot status like it is done with the stock
u-boot. Switch on the red power led if kernel image can't be loaded.
Otherwise switch the green led on.
Make only the ramboot u-boot available. Only this image is required for
the first installation of LEDE.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The host-side build of grub2 requires this sometimes.
This will re-generate the ./configure script from configure.ac.
I don't know the conditions of how this reproduces, it just
sometimes appears, and sometimes doesn't.
Build error
```
<lede-dir>/build_dir/target-x86_64_musl-1.1.15_yogi/host/grub-2.02~beta2/build-aux/missing: line 81: aclocal-1.14: command not found
WARNING: 'aclocal-1.14' is missing on your system.
You should only need it if you modified 'acinclude.m4' or
'configure.ac' or m4 files included by 'configure.ac'.
The 'aclocal' program is part of the GNU Automake package:
<http://www.gnu.org/software/automake>
It also requires GNU Autoconf, GNU m4 and Perl in order to run:
<http://www.gnu.org/software/autoconf>
<http://www.gnu.org/software/m4/>
<http://www.perl.org/>
Makefile:3962: recipe for target 'aclocal.m4' failed
```
Adding PKG_FIXUP adds sanity (i.e. autoreconf is used for host & target
builds) over just using HOST_FIXUP.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
The current uboot default config for the A13 SOM erroneously enables support
for the AXP209 power regulator IC which is not present on the board.
This superfluous support module sets an incorrect initial clock frequency and
confuses the kernel, ultimately leading to a boot failure later on.
Properly disable the PMIC support and enable the EHCI support by translating
the deprecated SYS_EXTRA_OPTIONS values into proper SUNXI_NO_PMIC and
USB_EHCI_HCD symbols respectively.
Also rename 002-add-olimex-a13-som.diff to 002-add-olimex-a13-som.patch and
refresh the remaining patches of the series while we're at it.
Reported-by: Mario Fischer <mario-fischer@web.de>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.
The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Add support for NXP layerscape ls1043ardb 64b/32b Dev board.
LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores.
ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC,
I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc.
64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from
NXP QorIQ SDK release.
All of 4.4 kernel patches porting from SDK release or upstream.
QorIQ SDK ISOs can be downloaded from this location:
http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Fix the default value for the 'bootcmd' environment variable.
Therefore make the default bootcmd work for buildbot's images.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Fix metadata scan failure in the grub2 package by removing an unexpected
invisible space character and by adding back the missing SECTION variable
which was removed with d140648.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
While enable zynq uboot:
CONFIG_PACKAGE_uboot-zynq-zc702
CONFIG_PACKAGE_uboot-zynq-zed
CONFIG_PACKAGE_uboot-zynq-zybo
make will arise dtc error:
./scripts/dtc-version.sh: line 17: dtc: command not found
./scripts/dtc-version.sh: line 18: dtc: command not found
*** Your dtc is too old, please upgrade to dtc 1.4 or newer
make[4]: *** [checkdtc] Error 1
Pass the kernel dtc to uboot for compile.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
because boot loaders are in Boot Loaders, not in Utilities -> Boot Loaders
Also moved brub2-editenv in Utilities -> Boot Loaders
Part of a wider housekeeping effort on the packages repository.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Boot Loaders submenu of Utilities is the most logical place to find fconfig and other bootloader tools.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Boot Loaders submenu of Utilities is the most logical place to find rbcfg and other bootloader tools.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
OpenWrt uses ancient u-boot thats not reproducible.
There are multiple upstream changes that introduce
reproducible builds like:
859e92b775fd8ebcfacc591eaf621b677c95b6f7
(not used here - the CMD_DATE/TIMESTAMP functionality
seems to be disabled by config)
70d39f57146a6cb94736db39c770c3d95e07bedb
f3f431a712729a1af94d01bd1bfde17a252ff02c
2d9efa1227262249d381ed5d9d341cbdba76e62d
Instead of changing the Makefile too much
this changeset just tries to use the
changes in Makefile from current upstream git f5fd45f
*Should* fix issue reported by reproducible lede page:
https://tests.reproducible-builds.org/lede/lede.html
Compile tested only
(verified w. hexdump & md5sum)
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
* Change git packages to xz
* Update mirror checksums in packages where they are used
* Change a few source tarballs to xz if available upstream
* Remove unused lines in packages we're touching, requested by jow- and blogic
* We're relying more on xz-utils so add official mirror as primary source, master site as secondary.
* Add SHA256 checksums to multiple git tarball packages
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Adds u-boot for the at91 platform and a couple of boards.
The build honours COPTS to benefit from fortify source et al.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Uboot-mvebu isn't a real package, which will break the image builder
when it tries to install it during the packing step. Instead of cleafog
selecting it through its default packages, make it default to m if the
clearfog profile is selected.
This will ensure it is always build, but never added to the rootfs. This
fixes creating images for clearfog with IB.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
The clearfog image requires u-boot, so package it into KDIR to make sure
it is available in imageBuilder.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
This allows kobs-ng to flash the SPL successfully on the 4.4 kernel used by
the Gateworks IMX boards supporting NAND. The previous version of kobs-ng
worked with the 3.14 kernel but will brick a board making its SPL unbootable
for the 4.4 kernel.
See http://trac.gateworks.com/wiki/ventana/bootloader#nandspl for instructions
on updating the SPL from Linux.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
tools/env/fw_env.c misses to include stdint.h.
Apparently musl doesn't mind and includes this header by default,
but glibc does not and causes the build to fail.
Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
In company networks everything except the http and https protocol is
often causes problems, because the network administrators try to block
everything else. To make it easier to use LEDE in company networks use
the https/http protocol for git access when possible.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Based on a submission to the uboot-lantiq repo by Eddi De Pieri.
Major cleanup and addition of brnboot second stage u-boot was done by
me.
The second stage brnboot u-boot is untested, since the brnboot prompt
is secured by a still unknown password. But should work.
The former ram values are replaced with the ram values extracted from
the original brnboot. The old ones didn't worked with the ramboot
image.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The default bootloader partition of some devices is to small for an
u-boot with uncompressed gphy firmware(s).
Instead of increasing the bootloader partition size, in compare to the
stock firmware, compress the firmware. This would allow the bootloader
of at least the FritzBox 3370 as well as the bootloader of the
VGV7510KW22 to fit into the bootloader partition of the stock firmware.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Based on a submission to the uboot-lantiq repo by Eddi De Pieri.
Devices like the xrx200 Arcadyan VGV7519 are using two NOR flash chips.
Signed-off-by: Mathias Kresin <dev@kresin.me>
According to the author, all SPI related configs are copy & paste
leftovers. Which makes sense since nothing is connected to the SPI bus
on this device.
The NOR SPL isn't required for this board, since the NOR is directly
memory mapped.
Allow to overwrite the env in ram while using brn variant. Do not set
the power GPIO pin twice.
Signed-off-by: Mathias Kresin <dev@kresin.me>
use:
- 00nn for u-boot patches
- 01nn for new boards
While doing the rework, the board definitions for the easy50712 and
easy80920 were moved to distinct board definitions patches.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
v3 includes changes suggested by L. D. Pinney & Karl Palsson-
Eliminate en25q64 (4MB) flash chip
Alphabetization
Remove hyphen in model
Rename profile from miwifinano.mk to xiaomi.mk
Add gpios that are attached to leds
SVN-Revision: 49024
Explicit sets the size of the mtdparts, because the kernel has also an explicit value.
If they have diffent sizes the ubi won't be detected.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49018
otherwise the uboot is missing important commands like bootz
Signed-off-by: Martin Mueller <mm@sig21.net>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49017
Since switching to new ubi(kernel,squashfs,ubifs) layout, the kernel lies in a
ubi volume. Dropping the mtd parts because the mtd layout is saved in the
device-tree, which is appended to the zImage.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49016
Add support for Xilinx ZC702 Dev board
Zynq target is using 4.4 kernel and mainline 2016.1 u-boot.
Patch is tested with Xilinx ZC702 Dev board with SD boot mode.
known issues:
- no QSPI driver in 4.4 kernel: no QSPI flash support
- USB is not working in 4.4 kernel
Signed-off-by: Jason Wu <jason.wu.misc@gmail.com>
create mode 100644 package/boot/uboot-zynq/Makefile
create mode 100644 target/linux/zynq/Makefile
create mode 100644 target/linux/zynq/base-files.mk
create mode 100755 target/linux/zynq/base-files/etc/board.d/02_network
create mode 100644 target/linux/zynq/base-files/etc/config/network
create mode 100644 target/linux/zynq/base-files/etc/inittab
create mode 100644 target/linux/zynq/config-4.4
create mode 100644 target/linux/zynq/image/Makefile
create mode 100755 target/linux/zynq/image/mkits.sh
create mode 100644 target/linux/zynq/patches-4.4/0001-arm-dts-zynq-zc702.dts-Set-default-rdinit-to-sbin-in.patch
create mode 100644 target/linux/zynq/profiles/zc702.mk
SVN-Revision: 48697
U-boot ships with the `mx6qsabresd` configuration file to configure a
bootloader suitable for booting the Freescale i.MX6q SABRE evaluation board
from SD card. Expose this option in the uboot-imx6 Makefile.
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
SVN-Revision: 48014
OpenWrt configuration part of support for the PowerCloud Systems
CR5000. The CR5000 is a dual-band 802.11n wireless router with
8MB flash, 64MB RAM, (unused on stock firmware) USB 2.0 port and
five port gigabit ethernet switch. The CR5000 was sold as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47946
OpenWRt configuration part of support for the PowerCloud
Systems CR3000. The CR3000 is a 802.11n 2.4 GHz wireless router with
8MB flash, 64MB RAM, a four port gigabit ethernet switch, and a fast
ethernet wan port that was sold by PowerCloud Systems as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47945
Openwrt configuration part of support for PowerCloud CAP324
Cloud AP. The CAP324 Cloud AP is a device sold by PowerCloud Systems
who's stock firmware (CloudCommand) provides 'cloud' based managment
of large numbers access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via PoE
or a wall wart.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47944
- tested on Beagleboard C4
- remove upstream patches
- disable THUMB mode on OMAP3 this increases binary size
(remove CONFIG_SYS_THUMB_BUILD)
- reduce SPL size by disabling EXT feature
(remove CONFIG_SPL_EXT_SUPPORT)
this fixes 2015.07 and 2015.10-rc3
Beagleboard C4 booting
which were broken by upstream commit
with id: bd2c4522c26d535515aebca52d27c004a7e0c05c
Arm THUMB mode is broken because of an yet unknown errata
see: http://lists.denx.de/pipermail/u-boot/2015-August/225793.html
- backport upstream fix that was introduced in 2015.10-rc5
and was not fixed in 2015.10 final
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 47924
gcc-5 handles inline without static differently and that makes
uboot-mxs fail to build. Remove the inline so it gets exported and can
be used in other functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47533
- Use board engineering names rather than marketing names
- Linksys uses a dual firmware layout, where the bootloader
will switch to the other stored image when one fails to
boot three consecutive times.
In order to make this firmware compatible with the factory
images and the stock bootloader we must match this layout.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 47429
The current patch to add Duckbill support is wrong and does not
even compile. So replace this patch with a working one.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 47007
Install uboot files to KERNEL_BUILD_DIR instead of BIN_DIR to fix
ImageBuilder. Similar fixes are necessary for many (all?) other uboot
targets.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46605
Invert the `__GLIBC__` guards into `!__UCLIBC__` ones to avoid
invalid references to `_llseek` on musl.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 46125
Add three download mirrors for 'grub', as the Makefile currently defines only
one download location.
@GNU can not be used, as the most recent version of 'grub' is not available
at the general GNU mirrors, and can only be found at the "gnu-alpha" mirrors.
Signed-off-by: Hannu Nyman <hannu.nyman at iki.fi>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 45909
- kexec-tools is now distributed with tarballs of .tar.gz and .tar.xz
format; .tar.bz2 are not provided anymore.
- Add CONFIG_KEXEC_LZMA for selecting lzma support.
Patches are updated along to:
- Remove the now unnecessary patch 0004-mips_regdefs.patch.
- Drop 100-reduce_size.patch because the size reduction is marginal.
- Allow zlib and lzma support coexist together. This patch has been
merged into upstream project.
- Fix kexec-tools' configure.ac.
- Fix a few compilation warnings.
Size comparison of stripped binaries of kexec malta target with both
zlib and lzma support enabled.
- Before: 41447
- After: 42583
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 44437
After r43987 TARGET_lantiq_xrx200_P2812HNUFX does not exist anymore.
Fix empty menuconfig bootloader selection by making u-boot depend on
one of the new target profiles.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 44179
KD20 got an IC+ phy, without the driver the phy is not properly
initialized resulting in ethernet not working unless being already
initialized by the vendor loader.
upstream commit 368b4d2b49bbbf379d9334747fbbd2aaaafe4356
drivers: net: remove dead drivers
removed icplus.c due to the lack of in-tree users.
Partially revert that commit adding back the IC+ driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43508
fixes BeagleBoard C4 detection
error message in serial console was:
"WARNING: Could not determine device tree to use"
change is found in upstream u-boot
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 43392
This adds support for the oxnas target in U-Boot 2014.04
History can be found at https://github.com/kref/u-boot-oxnas up to 2013.10
changes from 2013.10 to 2014.04 can be followed at
https://gitorious.org/openwrt-oxnas
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43389
This will ease adding new targets and updating:
* split UBOOTS var into multiple lines
* remove version from TITLE
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 43187
Note, that licensing stuff is a nightmare: many packages does not clearly
state their licenses, and often multiple source files are simply copied
together - each with different licensing information in the file headers.
I tried hard to ensure, that the license information extracted into the OpenWRT's
makefiles fit the "spirit" of the packages, e.g. such small packages which
come without a dedicated source archive "inherites" the OpenWRT's own license
in my opinion.
However, I can not garantee that I always picked the correct information
and/or did not miss license information.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 43155
Qihoo C301 has 2 flash chips of which one is used as primary and the
other is used as backup. OEM U-Boot will try to boot an activeregion N
with imageNstatus=0 and imageNtrynum <= imagemaxtry. If such a region
is found, bootloader will try to increment imageNtrynum and boot it.
This patch tries to reset imageNtrynum after each successful boot (if
the boot process reaches the execution of /etc/init.d/done).
root@OpenWrt:/# hexdump -C -n 128 /dev/mtdblock9
00000000 9e f3 63 91 61 63 74 69 76 65 72 65 67 69 6f 6e |..c.activeregion|
00000010 3d 31 00 69 6d 61 67 65 31 73 74 61 74 75 73 3d |=1.image1status=|
00000020 30 00 69 6d 61 67 65 32 73 74 61 74 75 73 3d 30 |0.image2status=0|
00000030 00 69 6d 61 67 65 32 74 72 79 6e 75 6d 3d 30 00 |.image2trynum=0.|
00000040 69 6d 61 67 65 6d 61 78 74 72 79 3d 33 00 69 6d |imagemaxtry=3.im|
00000050 61 67 65 31 74 72 79 6e 75 6d 3d 30 00 00 00 00 |age1trynum=0....|
00000060 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 42914
configure enables libzfs support on default.
This will break the build, on systems without libzfs.
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
SVN-Revision: 41935
Generate the configuration file for uboot-envtools
on BTHOMEHUBV2B. Adds the specific parameters for the
BTHOMEHUBV2B and also fixes an incorrect path which
would have affected other lantiq boards as well
(currently only the GIGASX76X).
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41597
Insert a missing #ifdef UBI around the use of libubi_close().
As the preceding if (libubi) will never be true on non-UBI builds,
compiling only failed when disabling optimization.
Also rebase patch to latest u-boot.git HEAD.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 41313
On UBI enabled devices, U-Boot might store it's environment on
UBI volume(s). Support this in uboot-envtools, so fw_setenv and
fw_printenv can work on these platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 40929
The settings require that the OpenWrt provided u-boot is used as either
first or second stage bootloader as it modifies the partitioning scheme
to move the u-boot environment to a separate mtd partition.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 40829
This patch modifies the u-boot config for the Pogoplug E02 to work with
OpenWrt. It also enables building a second stage bootloader image.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 40828
As both of the PKG_SOURCE_URLs within the Apex Makefile appear to be no
longer functional, this patch changes the source URL to the OpenWRT
downloads page. Apologies for resubmitting, but there was a syntax error
in the previous patch ( http://patchwork.openwrt.org/patch/5025 ).
Signed-off-by: Riley Baird <orthogonal@librewrt.org>
[florian: unmangle patch, fix subject]
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 40718
Depend on lantiq board.
ARV7510 depends on ARV4510 because (according to OpenWrt wiki) both boards are identical except for the unsupported WiFi. Moreover, ARV7510 isn't especifically supported and ARV4510 images valid.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 40544
By default kobs-ng will use the size of /dev/mtd0 for the IMX bootstreams.
This patch allows overriding that size in order to reserve space at the end
of the mtd partition for u-boot.img in the case of using an SPL bootloader.
For example, to flash an SPL bootloader that loads u-boot.img from 0xe0000
(14MB) offset in a 16MB /dev/mtd0:
kobs-ng init -v -x --search_exponent=1 --chip_0_size=0xe00000 SPL
nandwrite --start=0xe00000 --pad /dev/mtd0 u-boot.img
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 40532
Patches created from tree:
git@github.com:danielschwierzeck/u-boot-lantiq.git
v2013.10..u-boot-lantiq-v2013.10-openwrt4
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
SVN-Revision: 40482
Tested on:
* Cloud Engines Pogoplug E02
* RaidSonic ICY BOX IB-NAS62x0
* Iomega Iconnect
Some users are avoiding to replace their bootloader, because of that add
support for second stage u-boot image. Having ubifs capable bootloader is
required in order to boot current OpenWrt trunk.
Sample ib62x0 commands for running second stage bootloader:
tftpboot 0x800000 uboot-kirkwood-ib62x0_second_stage/openwrt-kirkwood-ib62x0_second_stage-u-boot.img
bootm 0x800000
Sample ib62x0 commands for flashing second stage bootloader:
tftpboot 0x800000 uboot-kirkwood-ib62x0_second_stage/openwrt-kirkwood-ib62x0_second_stage-u-boot.img
nand erase 0x100000 0x100000 ; nand write 0x800000 0x100000 0x${filesize}
nand read 0x800000 0x100000 0x100000 ; bootm 0x800000
While at it include parallel build support, use alphabetic order of the boards
and introduce common OpenWrt configuration.
Signed-off-by: Luka Perkov <luka@openwrt.org>
Tested-by (on ib62x0): Luka Perkov <luka@openwrt.org>
Tested-by (on dockstar): Alexander Couzens <lynxis@fe80.eu>
Tested-by (on iconnect): Wojciech Dubowik <wojciech.dubowik@neratec.com>
CC: Felix Kaechele <heffer@fedoraproject.org>
CC: Wojciech Dubowik <wojciech.dubowik@neratec.com>
CC: Alexander Couzens <lynxis@fe80.eu>
CC: Daniel Engberg <daniel.engberg@pyret.net>
CC: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 39590
grub-editenv allows to modify grub2 environment files. Add a new package
that build grub2 for the target and packs up grub-editenv.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 36574
Summary:
* remove all files/* (since merged to upstream)
* patches on nand-spl, mmc and lcd driver
Thanks a lot to Xiangfu Liu!
Signed-off-by: Xiangfu Liu <xiangfu@sharism.cc>
SVN-Revision: 35034
