Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports.
Specifications:
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 1024MB of DDR3
• Storage: 256MB Nand
• Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
• WLAN:
2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate
5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
• 1x USB 3.0
• 1 gpio-controlled dual color led (blue/red)
• Buttons: 1x soft reset / 1x WPS
• Power: 12V DC jack
A poulated serial header is onboard (J1004)
the connector size is a 4-pin 2.0 mm JST PH.
RX/TX is working, u-boot bootwait is active, secure boot is enabled.
Notes:
- Serial is completely deactivated in the stock firmware image.
- This commit adds only single partition support, that means
sysupgrade is upgrading the current rootfs partition.
- Installation can be done by serial connection or
SSH access on OEM firmware
Installation Instructions:
Most part of the installation is performed from an initramfs image
running OpenWrt, and there are two options to boot it.
Boot initramfs option 1: Using serial connection (3.3V)
1. Stop auto boot to get to U-boot shell
2. Transfer initramfs image to device
(openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb)
Tested using TFTP and a FAT-formatted USB flash drive.
3. Boot the initramfs image
# bootm
Boot initramfs option 2: From SSH access on OEM firmware
1. Copy the initramfs image to a FAT-formatted flash drive
(tested on single-partition drive) and connect it to device USB port.
2. Change boot command so it loads the initramfs image on next boot
Fallback to OEM firmware is provided.
# fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq'
3. Reboot the device to boot the initramfs
# reboot
Install OpenWrt from initramfs image:
1. Use SCP (or other way) to transfer OpenWrt factory image
2. Connect to device using SSH (on a LAN port)
3. Check MTD partition table.
rootfs and rootfs_1 should be mtd18 and mtd20
depending on current OEM slot.
# cat /proc/mtd
4. Do a ubiformat to both rootfs partitions:
# ubiformat /dev/mtd18 -y -f /path_to/factory_image
# ubiformat /dev/mtd20 -y -f /path_to/factory_image
5. Set U-boot env variable: mtdids
# fw_setenv mtdids 'nand0=nand0'
6. Get offset of mtd18 to determine current OEM slot
- If current OEM slot is 1, offset is 16777216 (0x1000000)
- If current OEM slot is 2, offset is 127926272 (0x7a00000)
# cat /sys/class/mtd/mtd18/offset
7. Set U-boot env variable: mtdparts
If current OEM slot is 1, run:
# fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)'
If current OEM slot is 2, run:
# fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)'
8. Set U-boot env variable: bootcmd
# fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0'
9. Reboot the device
# reboot
Note: this PR adds only single partition support, that means sysupgrade is
upgrading the current rootfs partition
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
The Edgecore EAP102 is a wall/ceiling mountable AP. The AP can be
powered by either PoE or AC adapter.
Device info:
- IPQ8071-A SoC
- 1GiB RAM
- 256MiB NAND flash
- 32MiB SPI NOR
- 2 Ethernet ports
- 1 Console port
- 2GHz/5GHz AX WLAN
- 2 USB 2.0 ports
Install instructions:
Prerequistes - TFTP server, preferrably within 192.168.1.0/24
Console cable plugged in (115200 8N1 no flow control)
1. Power on device and interrupt u-boot to obtain u-boot CLI
2. set serverip to IP address of the TFTP server:
`setenv serverip 192.168.1.250`
3. Download image from TFTP server:
`tftpboot 0x44000000 openwrt-ipq807x-generic-edgecore_eap102-squashfs-nand-factory.ubi`
4. Flash ubi image to both partitions and reset:
`sf probe
imxtract 0x44000000 ubi
nand device 0
nand erase 0x0 0x3400000
nand erase 0x3c00000 0x3400000
nand write $fileaddr 0x0 $filesize
nand write $fileaddr 0x3c00000 $filesize
reset`
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
* RAM: 1024MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet:
* 4x1G RJ45 ports (QCA8075) with 1x status LED per port
* 1x2.5G RJ45 port (QCA8081) with 1x status LED
* WLAN:
* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
* 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate
* 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate
* 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate
* USB: 1x USB3.0 Type-A port
* LED-s:
* System (Blue and Yellow)
* Network (Blue and Yellow)
* RGB light bar on top in X shape
* Buttons:
* 1x Power switch
* 1x Soft reset
* 1x Mesh button
* Power: 12V DC Jack
Installation instructions:
Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access
Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd21 and mtd22 are the correct indexes from above!
5. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
6. Reboot the device by:
reboot
Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:
7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: Robert Marko <robimarko@gmail.com>
QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports.
Specifications:
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 1024MB of DDR3
• Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR
(contains art and u-boot-env)
• Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C)
• WLAN:
2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate
5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate
• LEDs:
7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs
• Buttons: 1x soft reset / 1x WPS
• Power: 12V DC jack
A poulated serial header is onboard.
RX/TX is working, bootwait is active, secure boot is not enabled.
SSH can be activated in the stock firmware, hold WPS button til the second beep
(yes the router has a buzzer)
SSH is available on port 22200, login with user admin and
password "mac address of the router".
Installation Instructions:
• obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial)
• stop auto boot
• setenv serverip 192.168.10.1
• setenv ipaddr 192.168.10.10
• tftpboot the initramfs image
(openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb)
• bootm
• make sure that current_entry is set to "0":
"fw_printenv -n current_entry" should be print "0". If not,
do "fw_setenv current_entry 0"
• copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
to the device to /tmp folder
• sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin
this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4)
• reboot
Note: this leaves the second kernel / rootfs parition untouched. So if you want
to go back to stock, stop u-boot autoboot, "setenv current_entry 1" ,
"saveenv", "bootipq".
Stock firmware should start from the second partition.
Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt
in the first partitions
Make 10G Aquantia phy's work:
The aquantia phy's need a firmware to work. This can either be loaded
in linux with a userspace tool or in u-boot.
I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is
aq_load_fw available in u-boot. But first the right firmware needs to write
to the 0:ETHPHYFW mtd partition (it is empty on my device)
Grab the ethphy firmware image from:
https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn
and scp that to openwrt.
Check the 0:ETHPHYFW partition number:
cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10.
Backup the 0:ETHPHYFW partition:
dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place.
Write the new firmware image to the 0:ETHPHYFW partition:
"mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10".
Reboot to u-boot.
Check if aq_load_fw is working:
"aq_load_fw 0", that checks the firmware and if successfull,
loads iram and dram to one of the aquantia phy's.
If that worked, add the aq_load_fw to the bootcmd:
setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq"
"saveenv"
"reset"
Board reboots and the firmware load to both phy's should start and
then openwrt boots.
Check if the 10G ports work.
Note: lan port labeled "10G-2" is configured as WAN port as per default.
All other port are in the br-lan. This can be changed in the network config.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Edimax CAX1800 is a 802.11 ax dual-band AP
with PoE. AP can be ceiling or wall mount.
Specifications:
• CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz
• RAM: 512MB of DDR3
• Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env)
• Ethernet: 1x 1G RJ45 port (QCA8072) PoE
• WLAN:
2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate
• LEDs:
3 x GPIO-controlled System-LEDs
(form one virtual RGB System-LED)
black_small_square Buttons: 1x soft reset
black_small_square Power: 12V DC jack or PoE (802.3af )
An unpopulated serial header is onboard.
RX/TX is working, bootwait is active, secure boot is not enabled.
SSH can be activated in the stock firmware, but it drops only
to a limited shell .
Installation Instructions:
black_small_square obtain serial access
black_small_square stop auto boot
black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot)
black_small_square bootm
black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi
to the device
black_small_square write the image to the NAND:
black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0)
black_small_square ubiformat /dev/mtd0 -f -y openwrt-ipq807x-generic-edimax_cax1800-squashfs-
nand-factory.ubi
black_small_square reboot
Note: Device is not using dual partitioning (NAND contains other partitions
with different manufacture data etc.)
Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Redmi AX6 is a budget 802.11ax dual-band router/AP
Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 128MB NAND
* Ethernet: 4x1G RJ45 ports (QCA8075)
* WLAN:
* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LEDs:
* System (Blue/Yellow)
* Network (Blue/Yellow)
*Buttons: 1x soft reset
*Power: 12V DC jack
Installation instructions:
Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_redmi_ax6_ax3000#ssh_access
Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!
5. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
6. Reboot the device by:
reboot
Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:
7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: Zhijun You <hujy652@gmail.com>
Xiaomi AX3600 is a budget 802.11ax dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port
* WLAN:
* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LED-s:
* System (Blue and Yellow)
* IoT (Blue)
* Network (Blue and Yellow)
* Buttons: 1x Soft reset
* Power: 12V DC Jack
Installation instructions:
Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access
Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!
5. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
6. Reboot the device by:
reboot
Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:
7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Include NSS DP and SSDK (Pulled as dependency) by default on ipq807x to
provide wired networking to the target.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Qualcomm Atheros IPQ807x is a modern WiSoC featuring:
* Quad Core ARMv8 Cortex A-53
* @ 2.2 GHz (IPQ8072A/4A/6A/8A) Codename Hawkeye
* @ 1.4 GHz (IPQ8070A/1A) Codename Acorn
* Dual Band simultaneaous IEEE 802.11ax
* 5G: 8x8/80 or 4x4/160MHz (IPQ8074A/8A)
* 5G: 4x4/80 or 2x2/160MHz (IPQ8071A/2A/6A)
* 5G: 2x2/80MHz (IPQ8070A)
* 2G: 4x4/40MHz (IPQ8072A/4A/6A/8A)
* 2G: 2x2/40MHz (IPQ8070A/1A)
* 1x PSGMII via QCA8072/5 (Max 5x 1GbE ports)
* 2x SGMII/USXGMII (1/2.5/5/10 GbE) on Hawkeye
* 2x SGMII/USXGMII (1/2.5/5 GbE) on Acorn
* DDR3L/4 32/16 bit up to 2400MT/s
* SDIO 3.0/SD card 3.0/eMMC 5.1
* Dual USB 3.0
* One PCIe Gen2.1 and one PCIe Gen3.0 port (Single lane)
* Parallel NAND (ONFI)/LCD
* 6x QUP BLSP SPI/I2C/UART
* I2S, PCM, and TDMA
* HW PWM
* 1.8V configurable GPIO
* Companion PMP8074 PMIC via SPMI (GPIOS, RTC etc)
Note that only v2 SOC models aka the ones ending with A suffix are
supported, v1 models do not comply to the final 802.11ax and have
lower clocks, lack the Gen3 PCIe etc.
SoC itself has two UBI32 cores for the NSS offloading system, however
currently no offloading is supported.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The target is in an incomplete state and will not receive Kernel 5.10
support, ego it should be dropped before the next release.
People are working on ipq807x with Kernel 5.15 which is only relevant
for the second next release. Once a working patchset exists the target
can be added again.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The default value for CONFIG_RCU_CPU_STALL_TIMEOUT was changed from 60
seconds to 21 seconds in 2012 in the upstream kernel. Some targets
already use 21 seconds.
This patch changes the default value in the generic configuration to 21
seconds and removes the target specific configuration options.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them
to the generic kconfigs. And resort the generic kconfigs while at it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Based on the existing documentation [1][2], I dare anyone to demonstrate that
we need to fine-tune these RCU parameters. The (performance) breakage potential
for doing so is immense, so let's just please put down this loaded footgun.
Disable CONFIG_RCU_EXPERT and its dependent symbols. Additionally, remove the
CONFIG_RCU_EXPERT symbol from the target kconfigs which contain it.
[1] https://www.kernel.org/doc/Documentation/RCU/Design/Data-Structures/Data-Structures.html
[2] https://lwn.net/Articles/777214/
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Do not deactivate the kernel configuration symbol CONFIG_STAGING in the
target configurations any more. This prevented the build of the exfat.ko
for example.
Fixes: FS#3979
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Otherwise the missing symbol is added to target config for every kernel
config refresh.
While at it, remove the disabled symbol from target configs.
Fixes: 4943bc5cff ("kernel: only strip proc for small flash devices")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
There is no such role as target maintainer anymore, one should always
send corresponding changes for the review and anyone from the commiters
is allowed to merge them or eventually use the hand break and NACK them.
Lets make it clear, that it is solely a community doing the maintenance
tasks.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
This is still missing a lot of love but people want to start working on it
so lets give them a common baseline.
Signed-off-by: John Crispin <john@phrozen.org>
