This reverts commit 931fcf6189.
The definition is wrong and require mac-base compatible. Also it's not
clear if it's correct to use 0xc for mac size.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The reset button was missing from the Enterasys WS-AP3715i DTS.
Add the node required for making the reset button work.
Signed-off-by: David Bauer <mail@david-bauer.net>
Label MAC detection does not work properly, as MAC address is assigned
on preinit. Thus, remove the label-mac definition.
Signed-off-by: David Bauer <mail@david-bauer.net>
Ethernet LED assignments were incorrectly swapped. Fix the assignment
logic so the correct LED is illuminated for the LAN LEDs.
Signed-off-by: David Bauer <mail@david-bauer.net>
Backport initial LEDs hw control support. Currently this is limited to
only rx/tx and link events for the netdev trigger but the API got
accepted and the additional modes are working on and will be backported
later.
Refresh every patch and add the additional config flag for QCA8K new
LEDs support.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The following adds the Aerohive BR200-WP router to OpenWrt under
the mpc85xx/p1010 subtarget.
Hardware:
- SoC: Freescale P1011
- NOR: Intel JS28F512M29EWH 64MB
- Memory: 2x Nanya NT5TU64M16GG-AC 128MB (Total of 256MB)
- 2.4GHz WiFi: Atheros AR9390-AL1A
- Eth1: Atheros AR8035-A PoE
- 2x LEDs
- 1x Button
- PoE PSE
Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a
password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, tftp boot the initramfs image:
dhcp; setenv serverip 192.168.1.3;
tftpboot 0x2004000 openwrt-mpc85xx-p1010-aerohive_br200-wp-initramfs-kernel.bin;
bootm 0x2004000;
3. Once booted, scp over the sysupgrade file and sysupgrade the device
to flash LEDE to the NOR.
Note:
MAC assigns are taken from stock firmware:
Name MAC addr Mode State Chan(Width) VLAN Radio Hive SSID
-------- -------------- -------- ----- ----------- ---- ---------- ---------- ---------
Mgt0 08ea:44XX:XXc0 - U - 1 - hive0 -
Eth0 08ea:44XX:XXc0 wan U - - - - -
Eth1 08ea:44XX:XXc2 access D - - - hive0 -
Eth2 08ea:44XX:XXc3 access D - - - hive0 -
Eth3 08ea:44XX:XXc4 access D - - - hive0 -
Eth4 08ea:44XX:XXc5 access D - - - hive0 -
Wifi0 08ea:44XX:XXd0 access U 1(20MHz) - radio_ng0 - -
Wifi0.1 08ea:44XX:XXd4 access D 1(20MHz) - radio_ng0 hive0 -
Note2:
PoE PSE could be managed with `realtek-poe` package. Example port
config:
config port
option enable '1'
option id '4'
option name 'lan2'
option poe_plus '0'
option priority '2'
config port
option enable '1'
option id '3'
option name 'lan1'
option poe_plus '0'
option priority '1'
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(switch@0 -> switch@10, Device's quickstart says LEDs are
amber and white => add function+color properties but keep
labels around, use pr_info)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
All targets are bumped to 5.15. Remove the old 5.10 patches, configs
and files using:
find target/linux -iname '*-5.10' -exec rm -r {} \;
Further, remove the 5.10 include.
Signed-off-by: Nick Hainke <vincent@systemli.org>
The legacy (BSD) PTY support could open security problems in a system,
We do not need them in OpenWrt, deactivate this option in all targets.
Debian also deactivates this option.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
SoC: NXP P1010 (1x e500 @ 800MHz)
RAM: 256M DDR3 (2x Samsung K4B1G1646G-BCH9)
FLASH: 32M NOR (Spansion S25FL256S)
BTN: 1x Reset
WiFi: 1x Atheros AR9590 2.4 bgn 3x3
2x Atheros AR9590 5.0 an 3x3
ETH: 2x Gigabit Ethernet (Atheros AR8033 / AR8035)
UART: 115200 8N1 (RJ-45 Cisco)
Installation
------------
1. Grab the OpenWrt initramfs, rename it to ap3715.bin. Place it in
the root directory of a TFTP server and serve it at
192.168.1.66/24.
2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot
by pressing Enter when prompted. Credentials are identical to the one
in the APs interface. By default it is admin / new2day.
3. Alter the bootcmd in U-Boot:
$ setenv ramboot_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66; tftpboot 0x2000000 ap3715.bin; bootm"
$ setenv boot_openwrt "sf probe 0; sf read 0x2000000 0x140000 0x1000000;
bootm 0x2000000"
$ setenv bootcmd "run boot_openwrt"
$ saveenv
4. Boot the initramfs image
$ run ramboot_openwrt
5. Transfer the OpenWrt sysupgrade image to the AP using SCP. Install
using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Signed-off-by: David Bauer <mail@david-bauer.net>
The kernel is already compressed with XZ by the bootwrapper, thus we
gain nothing by compressing it a second time.
Signed-off-by: David Bauer <mail@david-bauer.net>
The bootpage for the second core is placed by U-Boot in the upper 128k
of syste-memory.
This could either be a reserved-area or deducted from the total
system-memory. As only the latter is parsed by the bootwrapper, reduce
the available system memory for linux in order to preserve the bootpage
from being overwritten.
Signed-off-by: David Bauer <mail@david-bauer.net>
Kernel 5.10 builds currently fail because the patch for using the
simpleImage bootwrapper were not added to 5.10.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds properties to PCIe as well as ethernet nodes which are
normally added by the Extreme Networks U-Boot.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds properties normally filled by U-Boot. Also it fixes the node
name, which is incorrectly referring to a P1010 core.
Signed-off-by: David Bauer <mail@david-bauer.net>
This is normally filled by U-Boot. Prevents double-printing of early
console messages. Also enables debug-output by the zImage wrapper.
Signed-off-by: David Bauer <mail@david-bauer.net>
This reverts commit aa4a9058fb.
The assumption the bootloader fills out the MAC-address is not
correct. The MAC-address has to be set from userspace based on
information found in the device_id partition.
Signed-off-by: David Bauer <mail@david-bauer.net>
Disable interrupts for the eth-PHYs, as the interrupts are either not
firing or lost within the stack. Switch to polling the PHY status in the
meantime until a proper fix is implemented.
Ref: https://github.com/openwrt/openwrt/issues/12192
Signed-off-by: David Bauer <mail@david-bauer.net>
The boot-procedure for the Extreme WS-AP3825I is vfragile to put it
mildly. It does not relocate the FDT properly. It currently exercises
every step manually as well as coming with a pre-padded dtb.
Use the PowerPC bootwrapper code for legacy platforms with a pre-filles
DTS instead. We still need to ship a fit image to not break the fdt
resize / relocate instructions on existing boards. This does not require
adapting the U-Boot bootcommand.
Ref: https://github.com/openwrt/openwrt/issues/12223
Signed-off-by: David Bauer <mail@david-bauer.net>
The wrapper-image for the WL-WDR4900 was used as a build-target for the
kernel. This workd fine as long as only a single wrapper is used with
the OpenWrt build-system.
If additional wrappers are used, the build becomes racy in the
wrapper-stage.
The wrapper images actually do not represent a target. They are built
based on the kernel configuration. Only copy the resulting images to
avoid race-conditions as explained.
Signed-off-by: David Bauer <mail@david-bauer.net>
As the mac-address readout never worked, the mac-address fillout by the
bootloader is sufficient. Remove the readout for the Watchguard T10
then.
Signed-off-by: David Bauer <mail@david-bauer.net>
The mac-address accessor functions were not included in the sourced
script. Fix this by importing the correct script path.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
SoC: Freescale P1010
RAM: 512MB
FLASH: 1 MB SPI-NOR
512 MB NAND
ETH: 3x Gigabite Ethernet (Atheros AR8033)
SERIAL: Cisco RJ-45 (115200 8N1)
RTC: Battery-Backed RTC (I2C)
Installation
------------
1. Patch U-Boot by dumping the content of the SPI-Flash using a SPI
programmer. The SHA1 hash for the U-Boot password is currently
unknown.
A tool for patching U-Boot is available at
https://github.com/blocktrron/t10-uboot-patcher/
You can also patch the unknown password yourself. The SHA1 hash is
E597301A1D89FF3F6D318DBF4DBA0A5ABC5ECBEA
2. Interrupt the bootmenu by pressing CTRL+C. A password prompt appears.
The patched password is '1234' (without quotation marks)
3. Download the OpenWrt initramfs image. Copy it to a TFTP server
reachable at 10.0.1.13/24 and rename it to uImage.
4. Connect the TFTP server to ethernet port 0 of the Watchguard T10.
5. Download and boot the initramfs image by entering "tftpboot; bootm;"
in U-Boot.
6. After OpenWrt booted, create a UBI volume on the old data partition.
The "ubi" mtd partition should be mtd7, check this using
$ cat /proc/mtd
Create a UBI partition by executing
$ ubiformat /dev/mtd7 -y
7. Increase the loadable kernel-size of U-Boot by executing
$ fw_setenv SysAKernSize 800000
8. Transfer the OpenWrt sysupgrade image to the Watchguard T10 using
scp. Install the image by using sysupgrade:
$ sysupgrade -n <path-to-sysupgrade>
Note: The LAN ports of the T10 are 1 & 2 while 0 is WAN. You might
have to change the ethernet-port.
9. OpenWrt should now boot from the internal NAND. Enjoy.
Signed-off-by: David Bauer <mail@david-bauer.net>
The CONFIG_PPC_QUEUED_SPINLOCKS configuration option is not defined for
kernel 5.15, it is defined for kernel 5.10.
This fixes the compilation of mpc85xx/p2020 with kernel 5.15.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The default kernel should be switched to 5.15 in order to enable testing
by a broader audience.
Tested on TP-Link TL-WDR4900 v1.
Acked-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
This patch introduces DSA support for TP-Link TL-WDR4900 v1 switch.
Swconfig driver for QCA8327 switch is removed because this router is
only one device which use Qualcom swconfig switch.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Tested-by: Nick Hainke <vincent@systemli.org> # TP Link WDR4900 v1 (5.15)
Enables use of NVMe storage devices with appropriate adapter in miniPCIe slots (including for boot)
in Turris 1.x routers and possibly NXP P2020RDB boards
(these are the only currently supported p2020 devices according to docs[^1]).
Proper detection, mountability and readability was proved to be working
on Turris 1.1, OpenWrt 21.02 with similar configuration.
Increases gzip compressed kernel size by approximately 37 KiB (from 3 703 KiB to 3 740 KiB).
Should boot from those devices be possible the driver needs to be built in.
Inclusion as a module would prevent this functionality.
CONFIG_BLK_DEV_NVME=y
Includes NVMe driver in the kernel.[^2]
CONFIG_NVME_CORE=y
Selected by CONFIG_BLK_DEV_NVME.[^3] Not necessarily needed to be enabled explicitly,
but included to match the form of similar functionality implementations
for mvebu, x86_64 and rockchip_armv8 targets.
CONFIG_NVME_MULTIPATH disabled explicitly to prevent using more space than necessary.
[^1]: https://openwrt.org/docs/techref/targets/mpc85xx
[^2]: https://cateee.net/lkddb/web-lkddb/BLK_DEV_NVME.html
[^3]: https://cateee.net/lkddb/web-lkddb/NVME_CORE.html
Signed-off-by: Šimon Bořek <simon.borek@nic.cz>
This patch is part of Linux kernel 5.15.70, the content was removed, but
the empty file is still being carried over the repository, so remove it
once for all
Fixes: e1b009c ("kernel: bump 5.15 to 5.15.70")
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
While compiling OpenWrt master for Turris 1.x routers (p2020), it
reported following error:
Gianfar Ethernet (GIANFAR) [Y/n/m/?] y
Freescale DPAA2 Ethernet Switch (FSL_DPAA2_SWITCH) [N/m/y/?] (NEW)
Error in reading or end of file.
Let's fix it by disabling it.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Manually rebased:
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
[Move gro_skip in 680-NET-skip-GRO-for-foreign-MAC-addresses.patch to old position]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Similar to the lzma-loader on our MIPS targets, the spi-loader acts as
a second-stage loader that will then load and start the actual kernel.
As the TL-WDR4900 uses SPI-NOR and the P1010 family does not have support
for memory mapping of this type of flash, this loader needs to contain a
basic driver for the FSL ESPI controller.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
