Commit Graph

244 Commits

Author SHA1 Message Date
Tomasz Maciej Nowak
ddc0e87fae kernel: move TEO governor to generic config
This new symbol popped up in few places. Disable it in generic config.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[fixed merge conflict in generic/config-5.4]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-17 00:51:48 +01:00
Petr Štetiar
9ba09653ad treewide: remove maintainer variable from targets
There is no such role as target maintainer anymore, one should always
send corresponding changes for the review and anyone from the commiters
is allowed to merge them or eventually use the hand break and NACK them.

Lets make it clear, that it is solely a community doing the maintenance
tasks.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
2020-03-16 22:21:45 +01:00
Robert Marko
72c3997003 ipq40xx: 5.4: fix ethernet driver
In 5.4 kernel old u32 array way of setting network features was dropped and linkmode is now the only way.
So lets migrate the EDMA driver to support linkmode.
Also, old get/set settings API for ethtool is also dropped so lets convert to new ksettings API while at it as it demands linkmode.

Now, gigabit works properly as well as ethtool.
Previously you would get this in ethtool:
root@OpenWrt:/# ethtool eth1
Settings for eth1:
        Supports Wake-on: d
        Wake-on: d
        Current message level: 0x00000000 (0)

        Link detected: yes

Now, features are properly advertised:
root@OpenWrt:/# ethtool eth1
Settings for eth1:
        Supported ports: [ TP MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Supported pause frame use: Symmetric Receive-only
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Link partner advertised link modes:  10baseT/Half 10baseT/Full
                                             100baseT/Half 100baseT/Full
                                             1000baseT/Full
        Link partner advertised pause frame use: No
        Link partner advertised auto-negotiation: No
        Link partner advertised FEC modes: Not reported
        Speed: 1000Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 4
        Transceiver: internal
        Auto-negotiation: on
        MDI-X: Unknown
        Supports Wake-on: d
        Wake-on: d
        Current message level: 0x00000000 (0)

        Link detected: yes

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-03-16 22:21:45 +01:00
Robert Marko
2b7344055b ipq40xx: 5.4: fix networking PHY driver
In 5.4 kernel old u32 array way of setting network features was dropped and linkmode is now the only way.
So lets migrate the PHY driver to support linkmode.
Also, now in order for gigabit to work, PHY driver needs to advertise PHY_GBIT_FEATURES instead of PHY_BASIC_FEATURES

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
2020-03-16 22:21:45 +01:00
Petr Štetiar
f521ef5ff3 ipq40xx: 5.4: fix of_get_mac_address obsolete usage OOPs
of_get_mac_address returns valid pointer or ERR_PTR since 5.2 via commit
d01f449c008a ("of_net: add NVMEM support to of_get_mac_address") so the
patch fixes following OOPs on nbg6617:

 Unable to handle kernel paging request at virtual address ffffffed
 CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.4.24 #0
 PC is at edma_axi_probe+0x444/0x1114
 LR is at bus_find_device+0x88/0x9c

Where the PC can be resolved to:

 >>> l *edma_axi_probe+0x444
 0xc067be5c is in edma_axi_probe (./include/linux/string.h:378).

 >>> l *edma_axi_probe+0x43f
 0xc067be57 is in edma_axi_probe (drivers/net/ethernet/qualcomm/essedma/edma_axi.c:936)

Which leads to the following code fragment:

 935  mac_addr = of_get_mac_address(pnp);
 936  if (mac_addr)
 937      memcpy(edma_netdev[idx_mac]->dev_addr, mac_addr, ETH_ALEN);

Where using mac_addr=0xffffffed (-ENODEV) as source address in memcpy()
is causing the OOPs.

Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2020-03-16 22:21:45 +01:00
Robert Marko
e09a5efcdb ipq40xx: 5.4: enable NAND
Lets enable RAW NAND and Qcom NANDC drivers again in kernel 5.4.
They were dropped when 5.4 support was introduced due to upstream
changing the symbol names so refreshing was not enough.

Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[cut long line in commit message, enabled BCH as well]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-03-15 15:26:34 +01:00
Robert Marko
3ef988caf3 generic: 4.19: Add 4B_OPCODES flag to w25q256
This patch backports the upstream patch that adds the 4B_OPCODES flag to w25q256 under 4.19 kernel.
This is needed for ipq40xx and ramips.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2020-03-12 12:59:44 +01:00
Hauke Mehrtens
988546cd13 ipq40xx: Remove kernel 4.14 support
This target was switched to kernel 4.19 more than 6 months ago in commit
f342ffd300 ("treewide: kernel: bump some targets to 4.19") and now
with kernel 5.4 support being added it gets harder to support kernel
4.14 in addition to kernel 4.19 and 5.4.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2020-03-12 09:28:23 +01:00
Sungbo Eo
926f4da2b2 ipq40xx: replace ${} with $()
${} and $() are exactly the same. Follow the convention of using $().

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-03-11 19:24:37 +01:00
Leon M. George
377e8942b2 ipq40xx: add cpximg to flash Compex WPJ428 via bootloader
Generate a cpximg that is compatible with the cpximg loader in Compex' u-boot.
The cpximg loader can be started either by holding the reset button during power
up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept an image
appropriate for the board revision that is etched on the board (e.g. 6A04).

The image can be pushed using tftp:
  tftp -v -m binary 192.168.1.1 -c put openwrt-ipq40xx-generic-compex_wpj428-squashfs-cpximg-6a04.bin

cpximg files can also be used with the sysupgrade utility in stock images.
(add SSH key in luci for root access)

In mkmylofw_32m, the calculation of the "partition size" has been preferred
to just padding the partition as this will result in less block transfers
during flashing (while the additional complexity is bearable).

Signed-off-by: Leon M. George <leon@georgemail.eu>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-10 13:44:51 +01:00
Yousong Zhou
860652f4b9 kernel: 5.4: move some kconfig options to generic
CONFIG_64BIT_TIME=y
	CONFIG_KASAN_STACK=1
	CONFIG_UBSAN_ALIGNMENT=y
	CONFIG_UNIX_SCM=y
	CONFIG_DMA_DECLARE_COHERENT=y
	CONFIG_OF_RESERVED_MEM=y

Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2020-03-10 10:05:50 +08:00
Koen Vandeputte
f9f62d43e4 kernel: bump 5.4 to 5.4.24
Refreshed all patches.

Compile-tested on: imx6
Runtime-tested on: imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-03-09 20:43:53 +01:00
Koen Vandeputte
e64564920a kernel: bump 4.19 to 4.19.108
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-03-09 20:43:53 +01:00
Koen Vandeputte
d5a3536631 kernel: bump 4.14 to 4.14.172
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-03-09 20:43:53 +01:00
Robert Marko
6256ca3232 ipq40xx: add support for 8devices Habanero DVK
This patch adds support for the 8devices Habanero development board.

Specs are:
CPU: QCA IPQ4019
RAM: DDR3L 512MB
Storage: 32MB SPI-NOR and optional Parallel SLC NAND(Some boards ship with it and some without)
WLAN1: 2.4 GHz built into IPQ4019 (802.11n) 2x2
WLAN2: 5 GHz built into IPO4019 (802.11ac Wawe-2) 2x2
Ethernet: 5x Gbit LAN (QCA 8075)
USB: 1x USB 2.0 and 1x USB 3.0 (Both built into IPQ4019)
MicroSD slot (Uses SD controller built into IPQ4019)
SDIO3.0/EMMC slot (Uses the same SD controller)
Mini PCI-E Gen 2.0 slot (Built into IPQ4019)
5x LEDs (4 GPIO controllable)
2x Pushbutton (1 is connected to GPIO, other to SoC reset)
LCD ZIF socket (Uses the LCD controller built into IPQ4019 which has no driver support)
1x UART 115200 rate on J18

2x breakout development headers
12V DC Jack for power
DIP switch for bootstrap configuration

Installation instructions:
Since boards ship with vendors fork of OpenWrt sysupgrade can be used.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2020-03-09 00:53:50 +01:00
Robert Marko
4ff6c43499 ipq40xx: add IPQ4019 SD/MMC controller support
This commit finally adds support for the built in SD/MMC controller in IPQ4019 SoC.

Controller is supported by the upstream SDHCI-MSM driver with a minor clock setting patch.
Patch is special to the IPQ4019 and cannot be upstreamed.

LDO and SDHCI node are upstreamed, and LDO node is awaiting to be accepted.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2020-03-09 00:53:50 +01:00
Adrian Schmutzler
74cbc44086 ipq40xx: fix support of EnGenius EAP2200
This fixes a typo in the device string for MAC address setup in
02_network and corrects the indent in the device's DTS files.

While at it, move the aliases section before the keys section to
have it closer to the top of the file.

Fixes: a736d912e2 ("ipq40xx: add support for EnGenius EAP2200")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-05 12:53:06 +01:00
David Bauer
0d727f231f treewide: move commonly disabled symbols to generic config
Move new commonly disabled kernel 5.4 symbols to the generic kernel
configuration.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-03-01 00:51:23 +01:00
Christian Lamparter
91a7c9c27d ipq40xx: 5.4: refresh patches and config
This patch just refreshes the 5.4 patches. It seems as if
070-v4.20-soc-qcom-spm-add-SCM-probe-dependency.patch is
already applied, so drop it. It also does a quick
make kernel_oldconfig to get rid of unneeded symbols.

[Looks like USB and Ethernet need some more work].

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-02-28 22:46:27 +01:00
Eneas U de Queiroz
13b8404b1e ipq40xx: qce - add fixes for AES ciphers
This backports commits from master that fix AES ciphers when using the
qce driver:

 - A couple of simple fixes for CTR and XTS modes used with AES:
   * 041-crypto-qce-fix-ctr-aes-qce-block-chunk-sizes.patch
   * 042-crypto-qce-fix-xts-aes-qce-key-sizes.patch

 - A fix for a bug that affected cases when there were more entries in
   the input sg list than necessary to actually encrypt, resulting in
   failure in gcm, where the authentication tag is present after the
   encryption data:
   * 043-crypto-qce-save-a-sg-table-slot-for-result-buf.patch

 - A fix to update the IV buffer passed to the driver from the kernel:
   * 044-crypto-qce-update-the-skcipher-IV.patch

 - A patch that reduces memory footprint and driver initialization by
   only initializing the fallback mechanism where it is actually used:
   * 046-crypto-qce-initialize-fallback-only-for-AES.patch

 - Three patches that make gcm and xts modes work with the qce driver,
   and improve performance with small blocks:
   * 047-crypto-qce-use-cryptlen-when-adding-extra-sgl.patch
   * 048-crypto-qce-use-AES-fallback-for-small-requests.patch
   * 049-crypto-qce-handle-AES-XTS-cases-that-qce-fails.patch

 - A patch that allows the hashes/ciphers to be built individually.
   * 051-crypto-qce-allow-building-only-hashes-ciphers.patch

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[renumbered patches, added patches from dropped commit, refreshed, 5.4]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-02-28 22:46:09 +01:00
Eneas U de Queiroz
ee4a0afdcd ipq40xx: use neon crypto drivers
This adds the neon based implementations of AES & SHA256.

For AES, according to the kernel config help:

Use a faster and more secure NEON based implementation of AES in CBC,
CTR and XTS modes.
Bit sliced AES gives around 45% speedup on Cortex-A15 for CTR mode
and for XTS mode encryption, CBC and XTS mode decryption speedup is
around 25%. (CBC encryption speed is not affected by this driver.)
This implementation does not rely on any lookup tables so it is
believed to be invulnerable to cache timing attacks.
...
The observed speedups on ipq40xx are more modest: speedup is around 20%
for CTR mode and for XTS mode encryption, CBC and XTS mode decryption
speedup is around 10%. Measurements were made using tcrypt, with
1024-bytes blocks for CTR & CBC, and 4096-bytes for XTS.
The aes-neon-bs driver uses a fallback for CBC encryption; that fallback
could be either the generic driver written in C, or the scalar arm-asm
one.  Even though aes-arm is 1.9% slower, it is more resilient to timing
attacks (the reason for being slower), so it is being included here.

The neon sha256 module increases performance over the generic module by
33%.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[Enable only ciphers for now, reorder patch in series to help bisect
as new symbols could lead to build failures, 5.4]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-02-28 22:46:09 +01:00
Eneas U de Queiroz
26681de412 ipq40xx: qce - switch to skcipher API
This backports a commit updating the API of the QCE crypto engine to
what is used in current kerenl, easing future upstream backports.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[renumber patches, refreshed, added 5.4 patches]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-02-28 22:46:01 +01:00
Steven Lin
a736d912e2 ipq40xx: add support for EnGenius EAP2200
SOC:    IPQ4019 / QCA Dakota
CPU:    Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:   256 MiB
FLASH:  NOR 4 MiB + NAND 128 MiB
ETH:    Qualcomm Atheros QCA8072
WLAN1:  Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2:2x2
WLAN2:  Qualcomm Atheros QCA4019 5GHz 802.11a/n/ac 2:2x2
WLAN2:  Qualcomm Atheros QCA9888 5GHz 802.11a/n/ac 2:2x2
INPUT:  WPS Button
LEDS:   Power, LAN1, LAN2, WLAN 2.4GHz, WLAN 5GHz-1, WLAN 5GHz-2, OPMODE

1. Load Ramdisk via U-Boot

To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
   * 115200bps
   * 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports.
c. Set a static ip 192.168.99.8 for Ethernet that connects to board.
d. The PC must have a TFTP server launched and listening on the interface to which the board is connected.
e. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.

U-BOOT> set serverip 192.168.99.9 && tftpboot 0x84000000 192.168.99.8:openwrt.itb && bootm

Signed-off-by: Steven Lin <steven.lin@senao.com>
[copied 4.19 dts to 5.4]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-02-28 22:29:10 +01:00
John Crispin
272e0a702a ipq40xx: add v5.4 support
Signed-off-by: John Crispin <john@phrozen.org>
2020-02-28 17:50:46 +01:00
Koen Vandeputte
b6c9d2bab0 kernel: bump 4.19 to 4.19.105
Refreshed all patches.

Fixes:
- CVE-2013-1798
- CVE-2019-3016

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-02-24 14:19:16 +01:00
Koen Vandeputte
f4bea1b6a3 kernel: bump 4.14 to 4.14.171
Refreshed all patches.

Fixes:
- CVE-2013-1798

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-02-24 14:18:59 +01:00
Koen Vandeputte
20b5a4ca01 kernel: bump 4.19 to 4.19.101
Refreshed all patches.

Fixes:
- CVE-2019-14896
- CVE-2019-14897

Remove upstreamed:
- 023-0007-crypto-crypto4xx-Fix-wrong-ppc4xx_trng_probe-ppc4xx_.patch
- 950-0202-staging-bcm2835-camera-fix-module-autoloading.patch
- 001-4.22-01-MIPS-BCM63XX-drop-unused-and-broken-DSP-platform-dev.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-02-04 18:10:13 +01:00
Koen Vandeputte
1b310cff0f kernel: bump 4.14 to 4.14.169
Refreshed all patches.

Fixes:
- CVE-2019-14896
- CVE-2019-14897

Remove upstreamed:
- 023-0007-crypto-crypto4xx-Fix-wrong-ppc4xx_trng_probe-ppc4xx_.patch
- 001-4.22-01-MIPS-BCM63XX-drop-unused-and-broken-DSP-platform-dev.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-02-04 18:10:13 +01:00
Christian Lamparter
016339ba42 ipq40xx: fix misplaced cells-sizes in WPJ419's dts
This patch fixes the occurences of the following warning
message from the dtc:

Warning (reg_format): /soc/spi@78b5000/flash0@0/partitions/partition@0:reg:
property has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-01-26 01:20:46 +01:00
Yen-Ting-Shen
51f3035978 ipq40xx: add support for EnGenius EMD1
SOC:     IPQ4018 / QCA Dakota
CPU:     Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:    256 MiB
NOR:     32 MiB
ETH:     Qualcomm Atheros QCA8072 (1 port)
WLAN1:   Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2:   Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT:   RESET Button
LEDS:    White, Blue, Red, Orange

Flash instruction:

From EnGenius firmware to OpenWrt firmware:

In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emd1-squashfs-factory.bin directly.

From OpenWrt firmware to EnGenius firmware:

1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
   Put the EnGenius firmware in the TFTP server directory on your computer.
2. Power up EMD1. Press 4 and then press any key to enter u-boot.
3. Download EnGenius firmware
   (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emd1-nor-fw-s.img
4. Flash the firmware
   (IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script
5. Reboot
   (IPQ40xx) # reset

Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com>
[removed BOARD_NAME]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-01-26 01:20:45 +01:00
Fredrik Olofsson
52b8c7a892 ipq40xx: Add support for D-Link DAP-2610
Specifications
==============
- SOC: IPQ4018
- RAM: DDR3 256MB
- Flash: SPI NOR 16MB
- WiFi:
    - 2.4GHz: IPQ4018, 2x2, front end SKY85303-11
    - 5GHz: IPQ4018, 2x2, front end SKY85717-21
- Ethernet: 1x 10/100/1000Mbps, POE 802.3af
- PHY: QCA8072
- UART: GND, blocked, 3.3V, RX, TX / 115200 8N1
- LED: 1x red / green
- Button: 1x reset / factory default
- U-Boot bootloader with tftp and "emergency web server" accessible
  using serial port.

Installation
============
Flash factory image from D-Link web UI. Constraints in the D-Link web UI
makes the factory image unnecessarily large. Flash again using
sysupgrade from inside OpenWrt to reclaim some flash space.

Return to stock D-Link firmware
===============================
Partition layout is preserved, and it is possible to return to the stock
firmware simply by downloading it from D-Link and writing it to the
firmware partition.

    # mtd -r write dap2610-firmware.bin firmware

Quirks
======
To be flashable from the D-Link http server, the firmware must be larger
then 6MB, and the size in the firmware header must match the actual file
size. Also, the boot loader verifies the checksum of the firmware before
each boot, thus the jffs2 must be after the checksum covered part. This
is solved in the factory image by having the rootfs at the very end of
the image (without pad-rootfs).

The sysupgrade image which does not have to be flashable from the D-Link
web UI may be smaller, and the checksum in the firmware header only
covers the kernel part of the image.

Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
[added WRGG Variables to DEVICE_VARS, squashed spi pinconf/mux,
added emd1's gmac0 config,fix dtc warnings]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-01-26 01:20:45 +01:00
Koen Vandeputte
40842167d2 kernel: bump 4.19 to 4.19.98
Refreshed all patches.

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2020-01-24 13:14:33 +01:00
David Bauer
c6e972c877 ipq40xx: add support for Aruba AP-303H
The Aruba AP-303H is the hospitality version of the Aruba AP-303 with a
POE-passthrough enabled ethernet switch instead of a sigle PHY.

Hardware
--------

SoC:   Qualcomm IPQ4029
RAM:   512M DDR3
FLASH: - 128MB SPI-NAND (Macronix)
       - 4MB SPI-NOR (Macronix MX25R3235F)
TPM:   Atmel AT97SC3203
BLE:   Texas Instruments CC2540T
       attached to ttyMSM1
ETH:   Qualcomm QCA8075
LED:   WiFi (amber / green)
       System (red / green /amber)
       PSE (green)
BTN:   Reset
USB:   USB 2.0

To connect to the serial console, you can solder to the labled pads next
to the USB port or use your Aruba supplied UARt adapter.

Do NOT plug a standard USB cable into the Console labled USB-port!
Aruba/HPE simply put UART on the micro-USB pins. You can solder yourself
an adapter cable:

VCC - NC
 D+ - TX
 D- - RX
GND - GND

The console setting in bootloader and OS is 9600 8N1. Voltage level is
3.3V.

To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.

Installation
------------

1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
   into the TFTP server root directory. Configure the TFTP server to
   be reachable at 192.168.1.75/24. Connect the machine running the TFTP
   server to the E0 (!) ethernet port of the access point, as it only
   tries to pull from the WAN port.

2. Connect to the serial console. Interrupt autobooting by pressing
   Enter when prompted.

3. Configure the bootargs and bootcmd for OpenWrt.
   $ setenv bootargs_openwrt "setenv bootargs console=ttyMSM0,9600n8"
   $ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
     ubi read 0x85000000 kernel; set fdt_high 0x87000000;
     bootm 0x85000000"
   $ setenv ramboot_openwrt "run bootargs_openwrt;
     setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
     netget; set fdt_high 0x87000000; bootm"
   $ setenv bootcmd "run nandboot_openwrt"
   $ saveenv

4. Load OpenWrt into RAM:
   $ run ramboot_openwrt

5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
   /tmp folder on the device. You will need to plug into E1-E3 ports of
   the access point to reach OpenWrt, as E0 is the WAN port of the
   device.

6. Flash OpenWrt:
   $ ubidetach -p /dev/mtd16
   $ ubiformat /dev/mtd16
   $ sysupgrade -n /tmp/openwrt-sysupgrade.bin

To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:

  $ setenv bootcmd "boot"
  $ saveenv

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-01-14 09:38:32 +01:00
Tom Brouwer
2090b8af0a ipq40xx: add support for EZVIZ CS-W3-WD1200G EUP
Hardware:
SOC:    Qualcomm IPQ4018
RAM:	128 MB Nanya NT5CC64M16GP-DI
FLASH:  16 MB Macronix MX25L12805D
ETH:    Qualcomm QCA8075 (4 Gigabit ports, 3xLAN, 1xWAN)
WLAN:   Qualcomm IPQ4018 (2.4 & 5 Ghz)
BUTTON: Shared WPS/Reset button
LED:    RGB Status/Power LED
SERIAL: Header J8 (UART, Left side of board). Numbered from
        top to bottom:
        (1) GND, (2) TX, (3) RX, (4) VCC (White triangle
        next to it).
        3.3v, 115200, 8N1

Tested/Working:
* Ethernet
* WiFi (2.4 and 5GHz)
* Status LED
* Reset Button (See note below)

Implementation notes:
* The shared WPS/Reset button is implemented as a Reset button
* I could not find a original firmware image to reverse engineer, meaning
currently it's not possible to flash OpenWrt through the Web GUI.

Installation (Through Serial console & TFTP):
1. Set your PC to fixed IP 192.168.1.12, Netmask 255.255.255.0, and connect to
one of the LAN ports
2. Rename the initramfs image to 'C0A8010B.img' and enable a TFTP server on
your pc, to serve the image
2. Connect to the router through serial (See connection properties above)
3. Hit a key during startup, to pause startup
4. type `setenv serverip 192.168.1.12`, to set the tftp server address
5. type `tftpboot`, to load the image from the laptop through tftp
6. type `bootm` to run the loaded image from memory
6. (If you want to return to stock firmware later, create an full MTD backup,
e.g. using instructions here https://openwrt.org/docs/guide-user/installation/generic.backup#create_full_mtd_backup)
7. Transfer the 'sysupgrade' OpenWrt firmware image from PC to router, e.g.:
`scp xxx-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/upgrade.bin`
8. Run sysupgrade to permanently install OpenWrt to flash: `sysupgrade -n /tmp/upgrade.bin`

Revert to stock:
To revert to stock, you need the MTD backup from step 6 above:
1. Unpack the MTD backup archive
2. Transfer the 'firmware' partition image to the router (e.g. mtd8_firmware.backup)
3. On the router, do `mtd write mtd8_firmware.backup firmware`

Signed-off-by: Tom Brouwer <tombrouwer@outlook.com>
[removed BOARD_NAME, OpenWRT->OpenWrt, changed LED device name to board name]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-01-12 15:57:58 +01:00
Christian Lamparter
a0c0ad728c ipq40xx: fix usbport trigger on the RT-AC58U with USB 2.0 devices
This patch partially reverts
"ipq40xx: remove unnecessary usb nodes in DTS for ASUS RT-AC58U"
as the change removed the usb2 port-trigger, so the LED would no
longer light-up when a USB 2.0 was inserted into the USB port.

Fixes: d0efb1ba95 ("ipq40xx: remove unnecessary usb nodes in DTS for ASUS RT-AC58U")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-01-12 15:47:50 +01:00
Adrian Schmutzler
9c7025b779 ipq40xx: build DEVICE_DTS based on SOC and device name
This patch uses the SOC variable to calculate DTS names automatically
based on the SOC and the device definition node name.

This reduces redundancy and (by having to choose DTS name
appropriately) will unify the naming of a device in different places
(image/Makefile, DTS name, compatible, image name). This is supposed
to make life easier for developers and reviewers.

Since the kernel uses a "soc-device.dts" scheme for this target, we
use this for the derivation of DEVICE_DTS, too, and rename the files
not having followed it so far.

Note that for some devices the kernel itself is inconsistent, leaving
us with a manual overwrite for ap.dk01.1-c1 and ap.dk04.1-c1.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-12-27 18:00:15 +01:00
Paul Fertser
0b7d779dcf ipq40xx: use ath10k-ct-smallbuffers for 128 MiB devices
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2019-12-26 15:48:23 +01:00
Hauke Mehrtens
729d7bc751 kernel: Deactivate CONFIG_SFP in generic config
Deactivate CONFIG_SFP for kernel 4.19 in the generic configuration.
The CONFIG_SFP configuration option was not set to anything in the
ath79 build for me, set it to deactivated by default.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2019-12-23 15:25:36 +01:00
Sungbo Eo
d0efb1ba95 ipq40xx: remove unnecessary usb nodes in DTS for ASUS RT-AC58U
RT-AC58U has single USB 3.0 port, and only usb3_port1 is actually used.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-12-22 01:04:51 +01:00
Sungbo Eo
8083969405 ipq40xx: improve ASUS RT-AC58U support
This patch does the following:

- move WiFi LED setup to DTS
- fix LAN/WAN MAC addresses and add label MAC address
- wan5G -> wlan5G, power -> led_power
- increase flash SPI frequency to 30MHz

MAC addresses are stored in Factory partition at:
0x1006: WiFi 2.4GHz, WAN (label_mac)
0x5006: WiFi 5GHz, LAN (label_mac +4)

By improving flash speed,
`time dd if=/dev/mtdblock8 of=/dev/null bs=2k`
is reduced from 7m 10.26s to 5m 9.52s.
Using higher frequencies did not improve speed further.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2019-12-22 01:04:51 +01:00
David Bauer
102c8c55f2 ipq40xx: add support for Aruba AP-303
Hardware
--------

SoC:   Qualcomm IPQ4029
RAM:   512M DDR3
FLASH: - 128MB NAND (Macronix MX30LF1G18AC)
       - 4MB SPI-NOR (Macronix MX25R3235F)
TPM:   Atmel AT97SC3203
BLE:   Texas Instruments CC2540T
       attached to ttyMSM0
ETH:   Atheros AR8035
LED:   WiFi (amber / green)
       System (red / green)
BTN:   Reset

To connect to the serial console, you can solder to the labled pads next
to the USB port or use your Aruba supplied UARt adapter.

Do NOT plug a standard USB cable into the Console labled USB-port!
Aruba/HPE simply put UART on the micro-USB pins. You can solder yourself
an adapter cable:

VCC - NC
 D+ - TX
 D- - RX
GND - GND

The console setting in bootloader and OS is 9600 8N1. Voltage level is
3.3V.

To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.

Installation
------------

1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
   into the TFTP server root directory. Configure the TFTP server to
   be reachable at 192.168.1.75/24. Connect the machine running the TFTP
   server to the ethernet port of the access point.

2. Connect to the serial console. Interrupt autobooting by pressing
   Enter when prompted.

3. Configure the bootargs and bootcmd for OpenWrt.
   $ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8"
   $ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
     ubi read 0x85000000 kernel; bootm 0x85000000"
   $ setenv ramboot_openwrt "run bootargs_openwrt;
     setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
     netget; set fdt_high 0x87000000; bootm"
   $ setenv bootcmd "run nandboot_openwrt"
   $ saveenv

4. Load OpenWrt into RAM:
   $ run ramboot_openwrt

5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
   /tmp folder on the device.

6. Flash OpenWrt:
   $ ubidetach -p /dev/mtd1
   $ ubiformat /dev/mtd1
   $ sysupgrade -n /tmp/openwrt-sysupgrade.bin

To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:

  $ setenv bootcmd "boot"
  $ saveenv

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-12-20 17:48:52 +01:00
Robert Marko
146eb4925c ipq40xx: add support for Crisis Innovation Lab MeshPoint.One
MeshPoint.One is Wi-Fi hotspot and smart IoT gateway (based upon
Jalapeno module from 8Devices).

MeshPoint.One (https://meshpointone.com) is a unique Wi-Fi hotspot and
smart city gateway that can be installed and powered from street
lighting (even solar power in the future).  MeshPoint provides up to 27
hours of interrupted Wi-Fi and IoT services from internal battery even
when external power is not available.  MeshPoint.One can be used for
disaster relief efforts in order to provide instant Wi-Fi coverage that
can be easily expanded by just adding more devices that create wide area
mesh network.  MeshPoint.One devices have standard Luci UI for
management.

Features:
- 1x 1Gpbs WAN
- 1x 1Gbps LAN
- POE input (eth0)
- POE output (eth1)
- Sensor for temperature, humidity and pressure (Bosch BME280)
- current, voltage and power measurement via TI INA230
- Hardware real time clock
- optional power via Li-Ion battery
- micro USB port with USB to serial chip for easy OpenWrt terminal
  access
- I2C header for connecting additional sensors

Installation:
-------------
Simply flash the sysupgrade image from stock firmware.

Or use the built in Web recovery into bootloader:
Hold Reset button for 5 to 20 seconds or use UART and httpd command.
Web UI will appear on 192.168.2.100 by default.
For web recovery use the factory.ubi image.

Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
Signed-off-by: Damir Franusic <damir.franusic@sartura.hr>
Signed-off-by: Valent Turkovic <valent@meshpoint.me>
Signed-off-by: Robert Marko <robert@meshpoint.me>
[commit description long line wrap, usb->USB]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-11-30 00:53:36 +01:00
Robert Marko
c550b1acfc ipq40xx: use DTSI for Jalapeno
Lets move common code for Jalapeno into DTSI, this way Jalapeno based
boards don't introduce duplicate code.

While at it, lets also fix some style issues and update to current DTS
style.

Signed-off-by: Robert Marko <robert@meshpoint.me>
[commit description long line wrap]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-11-30 00:53:36 +01:00
Koen Vandeputte
e29500eb84 kernel: bump 4.19 to 4.19.85
Refreshed all patches.

Altered patches:
- 080-sata_support.patch

Remove upstreamed:
- 034-v4.20-MIPS-BCM47XX-Enable-USB-power-on-Netgear-WNDR3400v3.patch
- 001-4.21-01-BCM63XX-fix-switch-core-reset-on-BCM6368.patch
- 073-qcom-ipq4019-fix-cpu0-s-qcom-saw2-reg-value.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-22 16:56:46 +01:00
Koen Vandeputte
db9e9e8382 kernel: bump 4.14 to 4.14.155
Refreshed all patches.

Altered patches:
- 707-dpaa-ethernet-support-layerscape.patch

Remove upstreamed:
- 034-v4.20-MIPS-BCM47XX-Enable-USB-power-on-Netgear-WNDR3400v3.patch
- 001-4.21-01-BCM63XX-fix-switch-core-reset-on-BCM6368.patch
- 073-qcom-ipq4019-fix-cpu0-s-qcom-saw2-reg-value.patch

Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-22 16:56:46 +01:00
Koen Vandeputte
50ff887f41 ipq40xx: fix build error
Add missing brace which was accidentally omitted

Fixes: d6aea46a50 ("kernel: bump 4.14 to 4.14.154")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-20 09:26:26 +01:00
Koen Vandeputte
d6aea46a50 kernel: bump 4.14 to 4.14.154
Refreshed all patches.

Altered patches:
- 902-debloat_proc.patch
- 040-dmaengine-qcom-bam-Process-multiple-pending-descript.patch
- 807-usb-support-layerscape.patch
- 809-flexcan-support-layerscape.patch
- 816-pcie-support-layerscape.patch

Remove upstreamed:
- 150-MIPS-bmips-mark-exception-vectors-as-char-arrays.patch
- 303-spi-nor-enable-4B-opcodes-for-mx66l51235l.patch

New symbols:
X86_INTEL_MPX
X86_INTEL_MEMORY_PROTECTION_KEYS
X86_INTEL_TSX_MODE_OFF
X86_INTEL_TSX_MODE_ON
X86_INTEL_TSX_MODE_AUTO
SGL_ALLOC

Compile-tested on: cns3xxx, x86_64
Runtime-tested on: cns3xxx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-11-19 14:59:03 +01:00
Kristian Evensen
6ab84579c6 ipq40xx: u4019: use reset-gpios instead of phy-reset-gpio
Use reset-gpio instead of the custom phy-reset-gpio property to do phy
reset on the U4019. phy-reset-gpio was incorrectly introduced when we
added support for the U4019, and will be deprecated.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2019-11-07 22:51:37 +01:00
Daniel Danzberger
8db4496443 ipq40xx: wpj419: use reset-gpios property for phy reset
The old GPIO based phy reset (phy-reset-gpio) will be removed form
the ipq40xx mdio driver in the future.

Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
2019-11-07 22:51:37 +01:00
DENG Qingfang
6abce4d5e4 ipq40xx: mdio: remove support for phy-reset-gpio
Commit 6f6c00cfc9 ("ipq40xx: Add support for Unielec U4019") has
introduced support for `phy-reset-gpio` DT property, which isn't needed
as the MDIO already supports `reset-gpios`[1] which could be used instead.

1. https://elixir.bootlin.com/linux/v4.19.81/source/Documentation/devicetree/bindings/net/mdio.txt

Ref: PR#2511
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[commit title and description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-11-07 22:51:37 +01:00