- specify CC target explicitly
- define KBUILD_SYM32=n to select "native" build format (if building with 64-bit arch)
- rewrap lines (for good)
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15702
Signed-off-by: Robert Marko <robimarko@gmail.com>
Instead of avoiding returning, propagate error so that the kernel
infrastructure can handle it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of ignoring errors, let the linux infrastructure handle it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16262
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Adds the x86_64 dependency for mlxsw_core
* Removes the redundant mlxsw_core dependency
from mlxsw-minimal and mlxsw-spectrum
* Removes the DCB configuration symbols because
they were moved into the generic configuration
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds the missing x86 dependency for
the Mellanox mlxcpld LED driver.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/15362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The company Zyxel rebranded some years ago.
Currently the casing is according to the old branding even
for newer devices which already use the new branding.
This commit aligns the casing of Zyxel everywhere.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15652
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There was a typo done for mt7925e and mt7925u in the KernelPackage
definitions, which caused the system to load the wrong kernel modules.
Signed-off-by: Daniel Pawlik <pawlik.dan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16236
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The firmware binaries were missing in kmod-mt7925-firmware package.
Signed-off-by: Daniel Pawlik <pawlik.dan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16239
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Like other Ethernet drivers, print link speed and duplex mode
when the interface is up. Formatting output at the same time.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Like other Ethernet drivers, print link speed and duplex mode
when the interface is up. Formatting output at the same time.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Like other Ethernet drivers, print link speed and duplex mode
when the interface is up. Formatting output at the same time.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Like other Ethernet drivers, print link speed and duplex mode
when the interface is up. Formatting output at the same time.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This log is noisy and useless, just ignore it.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
This log is noisy and useless, just ignore it.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
r8168, r8125 and r8126 have been transferred from https://github.com/noltari to
https://github.com/openwrt.
The old URL should still work after the transfer, but let's update it anyway.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This commits adds the RTW89 driver from Realtek.
Supports the Realtek 8851BE/8852AE/8852BE/8852CE PCIe wireless chips.
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16131
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use ath10k-ct 6.9 to better match mac80211 backports 6.9.x
Drop patch 010 that is merged upstream.
Add patch 001 to fix version to 6.9 (overlooked by upstream).
Refresh patches.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/16036
Signed-off-by: Robert Marko <robimarko@gmail.com>
Instead of enabling RSS support, let's introduce a variant and let users
choose between both variants since it can cause network issues.
Signed-off-by: Milinda Brantini <C_A_T_T_E_R_Y@outlook.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Instead of enabling RSS support, let's introduce a variant and let users
choose between both variants since it can cause network issues.
Signed-off-by: Milinda Brantini <C_A_T_T_E_R_Y@outlook.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
6.1.103 and 6.6.44 introduced breakage complaining about missing mtd_test.ko
for some targets.
Signed-off-by: Zxl hhyccc <zxlhhy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16093
Signed-off-by: Robert Marko <robimarko@gmail.com>
Compilation of mtd_test.ko should be added only for kernel 6.6 or above.
Fixes 26df88a ("kernel: Add kmod-mfd-test")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16085
Signed-off-by: Robert Marko <robimarko@gmail.com>
6.6.44 introduced breakage complaining about missing mtd_test.ko
for some targets.
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16061
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Handle the KEY_VENDOR key in gpio-button-hotplug driver. This is used
by Turris Omnia.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/13799
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is required by the DSL CPE API driver.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[update for new license]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This firmware is used by the vrx518 tc driver.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[update for new license]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This firmware is used by the vrx518 ep driver.
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
[update for new license]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the package for the Pixart PAC7302 USB Camera Driver kernel module.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch cleans up the following warnings during build:
"warning: format not a string literal"
```
conf.c: In function 'conf_askvalue':
conf.c:89:17: warning: format not a string literal and no format arguments [-Wformat-security]
89 | printf(_("(NEW) "));
| ^~~~~~
conf.c: In function 'conf_choice':
conf.c:285:33: warning: format not a string literal and no format arguments [-Wformat-security]
285 | printf(_(" (NEW)"));
| ^~~~~~
conf.c: In function 'check_conf':
conf.c:440:41: warning: format not a string literal and no format arguments [-Wformat-security]
440 | printf(_("*\n* Restart config...\n*\n"));
| ^~~~~~
conf.c: In function 'main':
conf.c:617:41: warning: format not a string literal and no format arguments [-Wformat-security]
617 | _("\n*** The configuration requires explicit update.\n\n"));
| ^
conf.c:669:25: warning: format not a string literal and no format arguments [-Wformat-security]
669 | fprintf(stderr, _("\n*** Error during writing of the configuration.\n\n"));
| ^~~~~~~
conf.c:673:25: warning: format not a string literal and no format arguments [-Wformat-security]
673 | fprintf(stderr, _("\n*** Error during update of the configuration.\n\n"));
| ^~~~~~~
conf.c:684:25: warning: format not a string literal and no format arguments [-Wformat-security]
684 | fprintf(stderr, _("\n*** Error during writing of the configuration.\n\n"));
| ^~~~~~~
```
And POSIX Yacc warnings
```
lex -ozconf.lex.c -L zconf.l
yacc -ozconf.tab.c -t -l zconf.y
zconf.y:34.1-7: warning: POSIX Yacc does not support %expect [-Wyacc]
34 | %expect 32
| ^~~~~~~
zconf.y:97.1-11: warning: POSIX Yacc does not support %destructor [-Wyacc]
97 | %destructor {
| ^~~~~~~~~~~
gcc -Wall -Wmissing-prototypes -Wstrict-prototypes -O2 -fomit-frame-pointer -DKBUILD_NO_NLS -c -o zconf.tab.o zconf.tab.c
gcc conf.o zconf.tab.o -o conf
```
After:
gcc -Wall -Wmissing-prototypes -Wstrict-prototypes -O2 -fomit-frame-pointer -DKBUILD_NO_NLS -c -o conf.o conf.c
yacc -Wno-yacc -ozconf.tab.c -t -l zconf.y
gcc -Wall -Wmissing-prototypes -Wstrict-prototypes -O2 -fomit-frame-pointer -DKBUILD_NO_NLS -c -o zconf.tab.o zconf.tab.c
gcc conf.o zconf.tab.o -o conf
Signed-off-by: Sean Khan <datapronix@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/15953
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Brings lots of driver updates and API changes needed for mt76 updates.
Disable iwlwifi and ath11k on 5.15, since backport is too difficult,
and the only remaining targets won't need those drivers.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Currently, SSDK is creating a fake SFP PHY which has no OF node populated,
thus making it impossible to pass it to NSS-DP so port can actually work.
We eliminated QCA-s connecting of the PHY by manually creating a string
and then matching by name and instead only support passing the PHY as
phandle via phy-handle.
So, lets just use the switch port node to which the SFP is connected to
anyway and set it as the PHY device OF node so we can pass it to NSS-DP.
Link: https://github.com/openwrt/openwrt/pull/15840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Convert DSL_XTUDir_t to DSL_AccessDir_t to get rid of enum-conversion
warning.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/15811
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Satisfy compiler expectations in a hell of typedef's and get rid of
system-wide workqueue flush. Results in warning-free compile of the TAPI
driver also with Linux 6.6.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/15811
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Package the sctp_diag.ko file which already gets build when kmod-sctp
and kmod-inet-diag are selected.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Package the mfd-core.ko kernel module. It is selected by the
kmod-hwmon-gsc already.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The mtd_nandbiterrs.ko kernel module was added with kernel 3.7. We
should package it like the other test modules.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
kxxhash_generic.ko is a soft dependency of kmod-fs-btrfs, but we did not
package it. Extract the kmod-lib-xxhash and then package
xxhash_generic.ko.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The kmod-fs-btrfs package has a soft dependency to kmod-crypto-blake2b
The CONFIG_BTRFS_FS kernel build option selects CONFIG_CRYPTO_BLAKE2B,
but we did not package it before.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The kernel provides two variants of the lz4 compression a normal version
and a high compression mode version. The old kmod-lib-lz4 package
contained the normal version plus one part of the lz4hc version. There
was already code which selected the kmod-lib-lz4hc package which did
not exists.
I split this into 3 packages. kmod-lib-lz4 and kmod-lib-lz4hc for the
normal the and high compression algorithm which contain the specific
code and the kmod-lib-lz4-decompress which contains the common
decompressor.
New we are also packaging lz4hc.ko
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The nf_dup_ipv4.ko and nf_dup_ipv6.ko kernel module were packaged by
kmod-ipt-tee and kmod-nft-dup-inet at the same time. Extract them into a
separate package used by both.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/15833
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport patch for G761 PWM Fan controller support. This is used by
an ipq807x RAX120v2 and have an internal clock that was currently
unconfigured making the device not working.
Link: https://github.com/openwrt/openwrt/pull/15796
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Trying to compile for ipq60xx will fail with:
ERROR: modpost: "qca808x_phy_reset" [build_dir/target-aarch64_cortex-a53_musl/linux-qualcommax_ipq60xx/qca-ssdk-2024.06.13~c451136b/qca-ssdk.ko] undefined!
So, lets fix this by disabling Manhattan switch and PHY support as this is
the new 2.5G quad port switch that is not present on ipq60xx boards.
Fixes: 87a45ea432 ("kernel: qca-ssdk: update 12.5 to 2024-06-13")
Signed-off-by: Robert Marko <robimarko@gmail.com>
There are some new commits, so refresh and update patches.
Some build warnings have been fixed upstream too.
Add backport target/linux/generic/backport-6.6/722-v6.10-dt-bindings-arm-qcom-ids-Add-SoC-ID-for-IPQ5321.patch.
Removed upstream:
[-] qca-ssdk/patches/101-hsl_phy-add-support-for-detection-PSGMII-PHY-mode.patch
[-] qca-ssdk/patches/201-fix-compile-warnings.patch
List of changes:
2024-04-16 -c451136b- qca-ssdk: strip MRPPE code
2024-06-05 -f455a820- [qca-ssdk]: fix enum-int-mismatch warnings
2024-05-31 -bbfc0fa9- Merge "[qca-ssdk]: update eee status of phydev"
2024-05-31 -adbe9dc5- Merge "[qca-ssdk]: support psgmii and uqsxgmii mode of kernel"
2024-05-31 -d06ca777- Merge "[qca-ssdk]: fix 5G issue with the AQR FW that use 5gbaser for 5G speed"
2024-05-31 -c6f539a5- Merge "qca-ssdk: support mrppe pktedit padding functions"
2024-04-29 -c321e2a9- qca-ssdk: support mrppe pktedit padding functions
2024-05-24 -ee6e201e- qca-ssdk: Fix the big endian compile error
2024-05-15 -8c116bb9- [qca-ssdk]: update eee status of phydev
2024-05-20 -f0341a2c- Merge "qca-ssdk: Enable igmp for PPE MINI profile"
2024-05-16 -44a0ce93- qca-ssdk: Enable igmp for PPE MINI profile
2024-05-15 -8b91bbf6- [qca-ssdk]: support psgmii and uqsxgmii mode of kernel
2024-05-14 -7eec1658- [qca-ssdk]: fix 5G issue with the AQR FW that use 5gbaser for 5G speed
2024-05-12 -b9f5ea0e- [qca-ssdk]: ethtool support, do not change wake-up timer when the requested timer is 0
2024-05-09 -5e2c15ed- Merge "[qca-ssdk]: remove check when mht clock enable"
2024-05-09 -a1563b90- Merge "[qca-ssdk] support new sku IPQ5321"
2024-04-23 -f04b7680- [qca-ssdk]: show unknown status when link down
2024-03-22 -33b91b30- [qca-ssdk]: remove check when mht clock enable
2024-04-29 -b6362f2b- Merge "qca-ssdk:fix bug in marina nptv6 iid cal"
2024-04-29 -097033ae- Merge "[qca-ssdk] support cypress uniphy0 connecting MHT switch port0"
2024-04-24 -d45560fd- qca-ssdk:fix bug in marina nptv6 iid cal
2024-04-24 -7d7a42af- qca-ssdk: enable policer counter on low memory profile
2024-04-18 -e36cf6ea- Merge "[qca-ssdk]: change portvlan egress mode initial value as untouched"
2024-04-18 -27817881- Merge "[qca-ssdk]: update the aqr phy supported ability"
2024-04-18 -5a3a693c- Merge "qca-ssdk:support marina nptv6"
2024-04-16 -129fe9b3- Merge "qca-ssdk: support tunnel fields and innner fields inverse"
2024-01-09 -fc8f6abd- qca-ssdk:support marina nptv6
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15771
Signed-off-by: Robert Marko <robimarko@gmail.com>
It has its own dedicated knob
Signed-off-by: Nathaniel Wesley Filardo <nwfilardo@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15761
Signed-off-by: Robert Marko <robimarko@gmail.com>
New dependencies required for the module to be useful, and correct IPv6 support
Signed-off-by: Nathaniel Wesley Filardo <nwfilardo@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15761
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport upstream patch for tim->virtual_map flex array warning for
invalid write.
This has been notice with the bump of ath10k-ct to version 6.7.
Link: https://github.com/openwrt/openwrt/pull/15760
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport RX timestamp flags patch needed for ath10k-ct to compile with
newer versions.
Link: https://github.com/openwrt/openwrt/pull/15735
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
LEDs support for ath10k has finally merged upstream hence replace it
with the upstream version.
Link: https://github.com/openwrt/openwrt/pull/15735
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
LEDs support for ath10k has finally merged upstream hence replace it
with the upstream version.
Link: https://github.com/openwrt/openwrt/pull/15735
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit dc9c5d1ee7.
Additional file for ath10k-ct slipped in, revert for a better version
pushed later.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
LEDs support for ath10k has finally merged upstream hence replace it
with the upstream version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning:
./include/linux/export.h:29:22: error: passing argument 1 of 'class_create' from incompatible pointer type [-Werror=incompatible-pointer-types]
29 | #define THIS_MODULE (&__this_module)
| ~^~~~~~~~~~~~~~~
| |
| struct module *
/home/aleksander/workspace/openwrt/build_dir/target-mips_24kc_musl/linux-lantiq_xway/ltq-dsl-ar9/drv_dsl_cpe_api-3.24.4.4/src/common/drv_dsl_cpe_os_linux.c:1105:29: note: in expansion of macro 'THIS_MODULE'
1105 | dsl_class = class_create(THIS_MODULE, "dsl_cpe_api");
| ^~~~~~~~~~~
In file included from ./include/linux/device.h:31,
from ./include/linux/platform_device.h:13,
from ./include/linux/of_device.h:5,
from ./include/linux/of_platform.h:10,
from /home/aleksander/workspace/openwrt/build_dir/target-mips_24kc_musl/linux-lantiq_xway/ltq-dsl-ar9/drv_dsl_cpe_api-3.24.4.4/src/common/drv_dsl_cpe_os_linux.c:15:
./include/linux/device/class.h:230:54: note: expected 'const char *' but argument is of type 'struct module *'
230 | struct class * __must_check class_create(const char *name);
| ~~~~~~~~~~~~^~~~
/home/aleksander/workspace/openwrt/build_dir/target-mips_24kc_musl/linux-lantiq_xway/ltq-dsl-ar9/drv_dsl_cpe_api-3.24.4.4/src/common/drv_dsl_cpe_os_linux.c:1105:16: error: too many arguments to function 'class_>
1105 | dsl_class = class_create(THIS_MODULE, "dsl_cpe_api");
| ^~~~~~~~~~~~
./include/linux/device/class.h:230:29: note: declared here
230 | struct class * __must_check class_create(const char *name);
| ^~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Fix compilation warning:
./include/linux/export.h:29:22: error: passing argument 1 of 'class_create' from incompatible pointer type [-Werror=incompatible-pointer-types]
29 | #define THIS_MODULE (&__this_module)
| ~^~~~~~~~~~~~~~~
| |
| struct module *
/home/aleksander/workspace/openwrt/build_dir/target-mips_24kc_musl/linux-lantiq_xway/ltq-adsl-mei-ar9/ltq-adsl-mei/drv_mei_cpe.c:2774:34: note: in expansion of macro 'THIS_MODULE'
2774 | dsl_class = class_create(THIS_MODULE, "ifx_mei");
| ^~~~~~~~~~~
In file included from ./include/linux/device.h:31,
from ./include/linux/dma-mapping.h:8,
from ./include/linux/skbuff.h:28,
from ./include/net/net_namespace.h:43,
from ./include/linux/netdevice.h:38,
from /home/aleksander/workspace/openwrt/build_dir/target-mips_24kc_musl/linux-lantiq_xway/ltq-adsl-mei-ar9/ltq-adsl-mei/drv_mei_cpe.c:39:
./include/linux/device/class.h:230:54: note: expected 'const char *' but argument is of type 'struct module *'
230 | struct class * __must_check class_create(const char *name);
| ~~~~~~~~~~~~^~~~
/home/aleksander/workspace/openwrt/build_dir/target-mips_24kc_musl/linux-lantiq_xway/ltq-adsl-mei-ar9/ltq-adsl-mei/drv_mei_cpe.c:2774:21: error: too many arguments to function 'class_create'
2774 | dsl_class = class_create(THIS_MODULE, "ifx_mei");
| ^~~~~~~~~~~~
./include/linux/device/class.h:230:29: note: declared here
230 | struct class * __must_check class_create(const char *name);
| ^~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
All usages of mtd-cal-data have been removed. To avoid submissions that
rely on this deprecated behavior, remove it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15671
Signed-off-by: Robert Marko <robimarko@gmail.com>
Select DRIVER_11AX_SUPPORT and KERNEL_RELAY also for kmod-mt7996 to
prevent build failure if only this driver is selected during build and
end up with (most) required hostap features (IEEE 802.11be rates are not
yet supported).
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The 'kmod-stmmac-core' package is referenced by the following packages:
* kmod-dwmac-intel
* kmod-dwmac-imx
* kmod-dwmac-sun8i
The problem is that 'kmod-of-mdio' is not selectable for 'TARGET_x86'.
That means the package 'kmod-dwmac-intel' is not available on this
architecture and so the package 'kmod-dwmac-intel' could not be enabled.
To fix this remove the dependencies 'kmod-of-mdio' from 'kmod-stmmac-core'.
This is not needed on this level, because the modules 'kmod-of-mdio' is
already selected by the packages 'kmod-dwmac-imx' and 'kmod-dwmac-sun8i'.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
This adds some compile fixes for linux 6.6 compatibility.
class_create now require only the name instead of the module ownership
reference.
Also the kernel enabled checks for enum.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This adds some compile fixes for linux 6.6 compatibility.
class_create now require only the name instead of the module ownership
reference.
Also the kernel enabled checks for enum.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
struct u128 and u128_xor() was removed by upstream commit f413e724818c
("cyrpto/b128ops: Remove struct u128").
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This fixes some compile warnings for linux 6.6.
Flushing system-wide workqueues is dangerous and will be forbidden.
Replace system_wq with local vectoring_wq.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Commit ae8bf1a26e ("imx: add imx8m support") configured the
drm-imx-ldb kmod for imx_cortexa9 and imx_cortexa7 however it is only
applicable to imx_cortexa9 (imx6).
Fix this so that we can avoid a missing module config for cortexa7 when
moving to the 6.6 kernel.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
There are too many RTC drivers in other.mk, they deserve their
own menu and .mk-file, so let's break them out to a separate
entity.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Split the kmod-video-dma into kmod-video-dma-sg and
kmod-video-dma-contig. The old one contained two kmods, but sometimes
only one of them is build which caused problems. The configuration
options are not manually selectable in the kernel and hidden in OpenWrt.
Currently this causes build failures on some targets.
Fixes: 4d7cbe0a55 ("kernel: video-dma: explicitly state packaged modules")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Because wildcard in variable stating packaged modules, the filtering for
built-in kernel modules didn't work and would cause a packaging failure.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
At least kmod-fb-tft depends on CONFIG_FB_DEVICE and can not be
activated without it.
This configuration option was added with kernel 6.6, before this featre
was always activated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds a new mlxreg package, which allows access
to Mellanox programmable device register space through sysfs
interface for thermal control and hardware management.
It also adds required Mellanox I²C drivers and packages
for the "special" MSN4800 series and SN2201 platform.
Signed-off-by: Til Kaiser <mail@tk154.de>
During the last update to 12.5.r2 printing of the attached PHY-s was
removed, so lets bring it back as it is very helpfull for debugging
OpenWrt issues without users having to modify NSS-DP to know if a PHY
was attached.
Refresh patches since nss_dp_main.c was edited.
Link: https://github.com/openwrt/openwrt/pull/15537
Signed-off-by: Robert Marko <robimarko@gmail.com>
The IXP4xx is well supported upstream and can readily be
supported with kernel v6.6. To simplify things after the
DTS directory was renamed, switch to v6.6 only.
Bring in some outstanding patches.
Tested on the Gateworks GW2348-4.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the RTL8723BE PCIe Wi-Fi Adapter by adding backports drivers
Signed-off-by: David Adriao <davidadriao@dglitch.com>
[Do not remove rtl8xxxu and add dependency to rtl8723be-firmware]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is required for linux-6.1 compatibility.
IRQs are not automatically mapped from HW to virtual IRQ numbers when
the IRQ domain is registered. This happens when the IRQ number is read
from the device tree based on the IRQ domain from the device tree now.
In kernel 5.15 it was done when the IRQ domain was registered.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This makes the components used on the lantiq SoCs compile with kernel
6.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[also fix ifxmips_ptm_adsl.c]
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
gpio.h has been deprecated for a while and no longer compiles with 6.6.
Include the proper header.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15471
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, trying to compile qca-ssdk on macOS will fail in a weird way:
make[6]: *** No rule to make target 'openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-qualcommax_ipq807x/qca-ssdk-2024.04.17~3d060f7a/-n',
needed by 'openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-qualcommax_ipq807x/qca-ssdk-2024.04.17~3d060f7a/qca-ssdk.o'. Stop.
After looking looking at src_list.dep from which KBuild cmd_mod will
generate the list of objects to compile it looked like:
-n /src/adpt/adpt.c
-n
-n
Which was rather suspicous so after comparing to the same file but with
Fedora as host:
/src/adpt/adpt.c src/adpt/hppe/adpt_hppe_fdb.c src/adpt/hppe/adpt_hppe_mib.c
It was clear that echo -n which was used in SSDK-s target.mk was not
working as intented, and it looked like the POSIX only version of echo
was being used which does not honor -n.
So, after failling to reproduce it externally, replacing the call to echo
with a full path to coreutils echo fixed the compilation.
After further debugging, it was determined that SSDK does not honor
CONFIG_SHELL like other kernel modules so it was defaulting to /bin/sh as
the shell make was calling thus calling the /bin/sh built-in echo which on
macOS is the old Bash 3.2 one and it does not respect -n.
So, we have to explicitly pass SHELL=$(BASH) to SSDK to make it use bash
like kernel build or other kernel modules.
This is not an issue since on macOS we always build bash anyway.
Link: https://github.com/openwrt/openwrt/pull/15459
Signed-off-by: Robert Marko <robimarko@gmail.com>
Linux kernel commit torvalds/linux@b8a1a4cd5a
added a temporary probe_new member to struct i2c_driver, to drop the
rarely used second parameter of the probe function and not break API for
out of tree drivers. With torvalds/linux@5eb1e6e459,
which is part of v6.6, this probe_new member is dropped and the
signature of the probe function is updated.
ubnt-ledbar is used by the mediatek and ramips targets and both have
been updated to v6.6, so adapt the probe function signature and remove
other compat code for versions before v6.6.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Link: https://github.com/openwrt/openwrt/pull/15443
Signed-off-by: Robert Marko <robimarko@gmail.com>
This includes multiple updates for BCM2711 and BCM2712.
Full changelog:
0968de2871...1.20240424
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
There is a new branch 12.5.r2 for kernel 6.6, so refresh
and update patches.
Delete patch 0010-nss-dp-include-net-netdev_rx_queue.h.patch
Changes:
2024-04-04 -5bf8b91 [qca-nss-dp] Adding support for port ID 3 & 4 in MHT switch
2024-03-28 -ce1e4cf [qca-nss-dp] Use skb_queue_head_init instead of __skb_queue_head_init.
2024-03-11 -0d26366 [qca-nss-dp] Read MHT LAN port status for ErP phase2
2024-03-22 -8382f14 [qca-nss-dp] Fix compilation issues seen on ginger branch for Miami profile
2023-05-02 -09b0983 [qca-nss-dp] vp list processing for capwap
2024-02-22 -bc09a01 [qca-nss-dp] EDMA ring reset for PPE-DS
2024-03-12 -2fcb586 [qca-nss-dp] Fix the EDMA clock frequency for the mitigation timer configuration
2024-02-23 -44ba1be [qca-nss-dp] Add API to retrieve ethernet netdevs for ErP
2024-02-09 -a5979b7 [qca-nss-dp] send napi and ip checksum for VP handler
2024-01-12 -1b9cb5d qca-nss-dp: User netdev_alloc_skb_fast instead of dev_alloc_skb
2024-01-08 -a859b48 [qca-nss-dp] NAPI Budget and EDMA Rx size change for KPI improvement.
2024-01-06 -8935523 [qca-nss-dp] Offload L3, L4 checksum to hardware for ppe-vp.
2023-12-07 -bbd9547 [qca-nss-dp] Fix Compilation issues on kernel6.6
2023-10-12 -bc55f75 [qca-nss-dp]: Enable legacy SCS for PPE-VP.
2023-09-08 -6bd771f [qca-nss-dp] Invalidate secondary descriptor before use.
2023-12-19 -b143df8 [qca-nss-dp] Fixed nss_dp_hal_hw_reset functionality for ipq53xx.
2023-12-16 -7cfde1d [qca-nss-dp] Added nss_dp_hal_hw_reset functionality for ipq53xx.
2023-11-02 -70af6c2 [qca-nss-dp] Implement EDMA hang recovery support
2023-11-27 -2202b29 [qca-nss-dp] Add support for adding the link speed for the Miami's port connected to the internal Switch.
2023-12-06 -bef68a8 [qca-nss-dp] Resolve ring utilization reporting issue in EDMA driver
2023-12-06 -eaa7627 [qca-nss-dp] Add/Delete static fdb entries only for physical ports
2023-10-16 -4551d0f [qca-nss-dp]: Support HLOST_TID_override from PPE_VP path.
2023-11-09 -42ad3f3 [qca-nss-dp] Correct the NAPI poll implementation for DS Rx fill handling
2023-10-16 -dfeb7d3 [qca-nss-dp] Check for disabled ethernet port in ErP functions
2023-11-09 -42ad3f3 [qca-nss-dp] Correct the NAPI poll implementation for DS Rx fill handling
2023-10-16 -dfeb7d3 [qca-nss-dp] Check for disabled ethernet port in ErP functions
2023-09-22 -03f83d6 [qca-nss-dp] Correct the mht device flag
2023-08-18 -5efd7f4 [qca-nss-dp] Add EDMA Tx rings for MHT ports
2023-09-11 -7808ba2 [qca-nss-dp] Move DP standby code to new file and use new SSDK API
2023-09-28 -22ade1e [qca-nss-dp] : enable PPE-DS support in 6.x kernel
2023-08-28 -1943922 [qca-nss-dp] Support for bitmap based CPU selection.
2023-08-16 -dcb82a7 qca-nss-dp: 512M profile changes for Miami+Pebble
2023-09-01 -18e51f3 [qca-nss-dp] Fix tx descriptor completion error.
2023-08-28 -0bfde2d [qca-nss-dp] Changes to enable ErP mode
2023-09-05 -f1d635a [qca-nss-dp] Enable fast recycled changes in dp for kernel 6.1
2023-06-15 -55d35bd [qca-nss-dp] Tracking the full utilization of EDMA rings
2023-08-25 -89b9c19 [qca-nss-dp] Restricting the MTU as 9216 for all interfaces in DP
2023-01-03 -5098a4f [qca-nss-dp] Requeue Tx packet in case of Tx-failure.
2023-04-06 -3576dbb [qca-nss-dp] Adding tx napi with four queue per interface.
2023-08-10 -d2b6921 [qca-nss-dp] : changes to support ppe-qdisc for linux 6.x
2023-08-08 -a1941fb [qca-nss-dp] moving SET_NETDEV_DEV for all netdev to set.
2023-07-18 -74d3178 [qca-nss-dp] Reordering the CPU code and ACL index processing.
2023-06-30 -ab03139 [qca-nss-dp] Configure port level PPE offload flag in PPE
2023-06-06 -e9bb8c5 [qca-nss-dp] Rate limit the debug logs.
2023-07-18 -43afb9b [qca-nss-dp] Support Core selection for PPE mirrored packets.
2023-07-11 -92edcfd [qca-nss-dp] Add sysctl to invalidate RX secondary descriptor.
Tested and working on WAX620.
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15383
Signed-off-by: Robert Marko <robimarko@gmail.com>
Qualcomm recently committed a new branch (12.5.r2) targeting kernel
6.6. This lets us clean up a few patches particularly the one for
"C22/C45" mdio.
A quick way to see what changed for IPQ807x/6018 was to list the files produced
during build (**/*.o), replace the extension with ".c", and doing a
`git log`.
Filtering from those commits, ones of particular interest are listed
below:
```
2024-04-16 - 0d8f30aa - fix compile issue on hk with linux style build
2024-01-29 - 636464f7 - update the check for port link notify
2024-01-24 - 30c10e7f - enable and disable loopback for xgmac to fix qm stuck issue
2024-01-15 - b6ea10aa - update the the APIs to access switch
2024-01-08 - a1687502 - Disable Tx bridge mac before power off the PHY
2024-01-07 - 3eafb613 - support led configure for malibu phy
2024-01-07 - 5c1af60d - remove phy type check from mac reset when mode switch
2023-12-17 - 79d0b1e8 - remove the PHY access APIs in ssdk_plat.c
2023-12-16 - b2953740 - Update mii read/write functions
2023-12-11 - 37f2eac3 - add port id check for fdb entry
2023-12-11 - d040ca4d - support mdio clause45 on kernel6.6
2023-12-07 - 11494fbc - use barrier mw() during access fdb entry table
2023-12-03 - 8e40a284 - fix build warnings on kernel6.6
2023-11-10 - 10aa0a02 - change speed value when call ssdk_port_link_notify
2023-11-06 - ee4c4a60 - Update mac bitmap value of L3 table on MAC delete
2023-11-03 - 7cd27d39 - support 10G phy common feature
2023-10-30 - 383cc0d2 - fix mactype and mux select issue
2023-10-24 - decf534a - support autoneg status query on force port
2023-10-11 - 111d574e - move ssdk_led_init to regi_init
2023-10-08 - 6b14c142 - the combo port also need to parse SFP pins
2023-10-03 - fb2e0401 - fix port5 interface mode switch issue in erp case
```
Verified with users on QNAP 301W, NBG7815, and myself on Dynalink
DL-WRX36 that everything is functional, including LEDS.
Signed-off-by: Sean Khan <datapronix@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/15379
Signed-off-by: Robert Marko <robimarko@gmail.com>
* Allow kmod-acpi-video to be built for loongarch64:
The x86-specific CONFIG_ACPI_WMI will be split from default
kmod-acpi-video as a board-specific addition.
* Allow kmod-drm-amdgpu to be built for loongarch64:
Also add loongarch64-specific configs and modules.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
netlink.h header have NL_SET_ERR_MSG_MOD that is tied to kmods. We don't
need kmods on bpf tools and this cause compilation error if the header
is included. Fix it by dropping NL_SET_ERR_MSG_MOD.
Link: https://github.com/openwrt/openwrt/pull/11825
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This adds a kernel module package for the Marvell
MV88E6XXX DSA switch and a separate module package for
the DSA tagger since it can in theory be used by multiple
DSA switches. Enable both DSA and EDSA tags in the
tagger.
We can't just compile this in because just a few devices
has this DSA, and it depends on e.g. the I2C and SFP
to be loaded as modules first.
We have no examples of DSA switches being packaged as
modules before, all seem to be compiled in, but it
actually works just fine to do this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This update contains a minor fix to resolve "detected write beyond size
of field" warning during compilation:
* "replace [0] with []" (1d0d08c)
All patches still apply.
References:
* https://github.com/openwrt/openwrt/issues/15108
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
It seems that move to kernel 6.6 somehow fixed the remoteproc restart so
now it properly restarts and thus coldboot calibration works as well.
ipq60xx still seems to be broken in a different way so keep it disabled.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add patch fixing rmmod and insmod. Lots of flawed logic fixed that
permits the module to correctly rmmod and insmod later.
Just to quote some change, use phy_detach instead of phy_disconnect, fix
exclusive reset_control that could only be used once, fix kernel panic
on second edma_cleanup, stop traffic before module exit...
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Limiting allowed channels per device may be required and is commonly
supported on other drivers, so include a pending patch to add support for
the same.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Starting with Linux 6.3 the .probe call no longer got the id parameter,
see also commit torvalds/linux@03c835f498
("i2c: Switch .probe() to not take an id parameter").
As the parameter is anyway unused by the driver, drop it when
building the GCA230718 LED driver for newer kernels.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This module supports the Microchip Technology Inc (SMSC)
EMC2301/EMC2302/EMC2303/EMC2305 fan speed PWM controller chips.
Signed-off-by: Oleg S <remittor@gmail.com>
Historically it's possible to leave the `SUBTARGETS` undefined and
automatically fallback to a "generic" subtarget. This however breaks
various downstream scripts which may have expectations around filenames:
While some targets with an explicit generic subtarget contain `generic`
in the filenames of artifacts, implicit "subtargets" don't.
Right now this breaks the CI[1], possibly also scripts using the ImageBuilders.
This commit removes all code that support implicit handling of
subtargets and instead requires every target to define "SUBTARGETS".
[1]: https://github.com/openwrt/openwrt/actions/runs/8592821105/job/23548273630
Signed-off-by: Paul Spooren <mail@aparcar.org>
With the switch to ZSTD for git clone packaging, hashes have changed so
fixup remaining package hashes that were missed in the inital update.
Fixes: b3c1c57 ("treewide: update PKG_MIRROR_HASH to zst")
Signed-off-by: Robert Marko <robimarko@gmail.com>
When using zst instead of xz, the hash changes. This commit fixes the
hash for packages and tools in core.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Fix compilation warning enum-int-mismatch which results in failure to
build kmod-ltq-vmmc in case CONFIG_KERNEL_WERROR is set.
.../build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_common.c:392:14: error: conflicting types for 'ifx_mps_fastbuf_init' due to enum/integer mismatch; have 'IFX_return_t(void)' [-Werror=enum-int-mismatch]
392 | IFX_return_t ifx_mps_fastbuf_init (IFX_void_t)
| ^~~~~~~~~~~~~~~~~~~~
.../build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_common.c:120:13: note: previous declaration of 'ifx_mps_fastbuf_init' with type 'IFX_int32_t(void)' {aka 'int(void)'}
120 | IFX_int32_t ifx_mps_fastbuf_init (IFX_void_t);
| ^~~~~~~~~~~~~~~~~~~~
.../build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_common.c:420:14: error: conflicting types for 'ifx_mps_fastbuf_close' due to enum/integer mismatch; have 'IFX_return_t(void)' [-Werror=enum-int-mismatch]
420 | IFX_return_t ifx_mps_fastbuf_close (IFX_void_t)
| ^~~~~~~~~~~~~~~~~~~~~
.../build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_common.c:121:13: note: previous declaration of 'ifx_mps_fastbuf_close' with type 'IFX_int32_t(void)' {aka 'int(void)'}
121 | IFX_int32_t ifx_mps_fastbuf_close (IFX_void_t);
| ^~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Refresh patches and bump PKG_RELEASE while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Include the CONFIG_KVM_SMM option in the kvm-x86 package to enable system management mode emulation on KVM.
Co-authored-by: Stefan Hellermann <stefan@the2masters.de>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Fix error: Package kmod-lan743x is missing dependencies for the following libraries:
fixed_phy.ko
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Kernel 6.2 folded virqfd (eventd interface for VFIO interrupts)
into the base vfio module, it is no longer a tristate option.
Change suggested by vincejv on GitHub:
https://github.com/openwrt/openwrt/pull/14868#issuecomment-1998260124
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Instead of redefining the version schema in cryptodev, use the one
automatically defined via `kernel.mk`.
Specifically this changes the version from <kernel>+<package> to
<kernel>.<package> and thereby making it compatible with APK.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Add patch fixing compilation with kernel 6.6.
class_create now require only the name instead of the module ownership
reference.
Also the kernel enabled checks for enum.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation with kernel 6.6.
class_create now require only the name instead of the module ownership
reference.
Also the kernel enabled checks for enum.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add debugfs entry for disabling frames buffering that may be a reason
for mt7603 instability. This patch was sent upstream for review and at
least wasn't rejected yet. Let's add it to let OpenWrt users test if it
really helps.
Example usage:
echo N > /sys/kernel/debug/ieee80211/phy0/mt76/frames_buffering
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Build files shouldn't be symlinked into the staging directory, as doing so
would create a race condition if the build folder for 'qca-nss-dp' gets
deleted for any reason.
We should instead just copy over the required platform file to avoid
breaking compilation for any dependent packages.
Signed-off-by: Sean Khan <datapronix@protonmail.com>
The current build procedure always wipes away build files, this is
costly as ssdk is a parent dependency on a whole host of packages and
will always end up rebuilding (and in serial) the whole package.
This patch includes:
1. Module Building Optimization: Instead of creating a temporary
directory (temp) and copying files into it for module building,
the directly invoke the module build command with the
necessary paths. This simplifies the build process
and avoids unnecessary file operations, speeding up
the build process and reducing disk usage.
2. Parallel Build Support: By removing the explicit creation of
the temporary directory and associated file copying operations,
and passing in $(MAKE) $(PKG_JOBS) allows building in parallel.
3. Fix `EXTRA_CFLAGS`: This variable is referenced and set within MAKE_FLAGS,
so doesn't preserve spaces. Should have its defined value quoted.
Signed-off-by: Sean Khan <datapronix@protonmail.com>
Add basic support for the LED driver for GCA230718.
- I didn't find any documentation or driver for it, so the information below is purely based on my investigations
- If there is already I driver for it, please tell me. Maybe I didn't search enough
- I implemented a kernel module (leds-gca230718) to access the LEDs via DTS
- The LED controller supports PWM for brightness control and ramp control for smooth blinking. This is not implemented in the driver
- The LED controller supports toggling (on -> off -> on -> off) where the brightness of the LEDs can be set individually for each on cycle
- Until now, only simple active/inactive control is implemented (like when the LEDs would have been connected via GPIO)
- Controlling the LEDs requires three sequences sent to the chip. Each sequence consists of
- A reset command (0x81 0xE4) written to register 0x00
- A control command (for example 0x0C 0x02 0x01 0x00 0x00 0x00 0xFF 0x01 0x00 0x00 0x00 0xFF 0x87 written to register 0x03)
- The reset command is always the same
- In the control command
- byte 0 is always the same
- byte 1 (0x02 in the example above) must be changed in every sequence: 0x02 -> 0x01 -> 0x03)
- byte 2 is set to 0x01 which disables toggling. 0x02 would be LED toggling without ramp control, 0x03 would be toggling with ramp control
- byte 3 to 6 define the brightness values for the LEDs (R,G,B,W) for the first on cycle when toggling
- byte 7 defines the toggling frequency (if toggling enabled)
- byte 8 to 11 define the brightness values for the LEDs (R,G,B,W) for the second on cycle when toggling
- byte 12 is constant 0x87
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Kernel 6.3 has introduced separate C45 read/write operations, and thus
split them out of the C22 operations completely so the old way of marking
C45 reads and writes via the register value does not work anymore.
This is causing SSDK to fail and find C45 only PHY-s such as Aquantia ones:
[ 22.187877] ssdk_phy_driver_init[371]:INFO:dev_id = 0, phy_adress = 8, phy_id = 0x0 phytype doesn't match
[ 22.209924] ssdk_phy_driver_init[371]:INFO:dev_id = 0, phy_adress = 0, phy_id = 0x0 phytype doesn't match
This in turn causes USXGMII MAC autoneg bit to not get set and then UNIPHY
autoneg will time out, causing the 10G ports not to work:
[ 37.292784] uniphy autoneg time out!
So, lets detect C45 reads and writes by the magic BIT(30) in the register
argument and if so call separate C45 mdiobus read/write functions.
Signed-off-by: Robert Marko <robimarko@gmail.com>
With the change in version schema the downloaded files changed, too,
mostly the hash is now prefixed with a tilde `~` instead of a dash `-`.
Since each downloaded archive contains folder with the same name as the
archive, the checksum changed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Add imx8m support:
- add a cortexa53 subtarget to imx
- move ARCH and KERNELNAME to subtargets
- account for kernel modules that are not used for cortexa53
No device-specific targets or firmware images are created yet but all
imx8m* dtbs will be built.
enabling CONFIG_TARGET_ROOTFS_INITRAMFS results in
openwrt-imx-cortexa53-imx8m-initramfs-kernel.bin which has been
successfully booted on an imx8mm-evk using the following:
u-boot=> tftpboot $fdt_addr_r image-imx8mm-evk.dtb && \
tftpboot $kernel_addr_r openwrt-imx-cortexa53-imx8m-initramfs-kernel.bin && \
booti $kernel_addr_r - $fdt_addr_r
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The carl9170_tx_release() function sometimes triggers a fortified-memset
warning in my randconfig builds:
In file included from include/linux/string.h:254,
from drivers/net/wireless/ath/carl9170/tx.c:40:
In function 'fortify_memset_chk',
inlined from 'carl9170_tx_release' at drivers/net/wireless/ath/carl9170/tx.c:283:2,
inlined from 'kref_put' at include/linux/kref.h:65:3,
inlined from 'carl9170_tx_put_skb' at drivers/net/wireless/ath/carl9170/tx.c:342:9:
include/linux/fortify-string.h:493:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
493 | __write_overflow_field(p_size_field, size);
Kees previously tried to avoid this by using memset_after(), but it seems
this does not fully address the problem. I noticed that the memset_after()
here is done on a different part of the union (status) than the original
cast was from (rate_driver_data), which may confuse the compiler.
Unfortunately, the memset_after() trick does not work on driver_rates[]
because that is part of an anonymous struct, and I could not get
struct_group() to do this either. Using two separate memset() calls
on the two members does address the warning though.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
enable support for RK35xx in kmod-ata-ahci-platform kernel module
Suggested-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Different from OPKG, APK uses a deterministic version schema which chips
the version into chunks and compares them individually. This enforces a
certain schema which was previously entirely flexible.
- Releases are added at the very and end prefixed with an `r` like
`1.2.3-r3`.
- Hashes are prefixed with a `~` like `1.2.3~abc123`.
- Dates become semantic versions, like `2024.04.01`
- Extra tags are possible like `_git`, `_alpha` and more.
For full details see the APK test list:
https://gitlab.alpinelinux.org/alpine/apk-tools/-/blob/master/test/version.data
Signed-off-by: Paul Spooren <mail@aparcar.org>
Since 6.5 netdev_rx_queue was moved out of netdevice.h so include the new
header since that is where it lives now.
Signed-off-by: Robert Marko <robimarko@gmail.com>
