The CLK125 output pin at the ethernet PHY is connected via capacitor to
GND and nowhere else. Disable it. Also tune the LED masks.
The MPP56 and MPP60 pins at the SoC are conected to the μPD720202 USB3.0
chip:
- MPP56: wired to PCIe CLKREQ# (out)
- MPP60: wired to PCIe RESET# (in)
Configure the pcie pinmux for these pins.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
For the targets which enable ubifs, these symbols are already part of the
generic kconfigs. Drop them from the target kconfigs.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
The GL.iNet GL-MV1000 is booting from eMMC and the images for it are in
theory sysupgrade compatible. But the platform upgrade scripts were not
adjusted to select the mmcblock device as upgrade target. This resulted in
a failed sysupgrade because the mtd device (NOR flash) was instead tried to
be modified by the sysupgrade script.
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The crypto engine in Armada 370 SoCs is currently broken. It can be
checked installing the required packages for testing openssl with hw
acceleration:
opkg install openssl-util
opkg install kmod-cryptodev
opkg install libopenssl-devcrypto
After configuring /etc/ssl/openssl.cnf to let openssl use the crypto
engine for digest operations, and performing some checksums..
md5sum 10M-file.bin
openssl md5 10M-file.bin
...we can see they don't match.
There might be an alignment or size constraint issue caused by the
idle-sram area.
Use the whole crypto sram and disable the idle-sram area to fix it. Also
disable the idle support by adding the broken-idle property to prevent
accessing the disabled idle-sram.
We don't care about disabling the idle support since it is already broken
in Armada 370 causing a huge performance loss because it disables
permanently the L2 cache. This was reported in the Openwrt forum and
elsewhere by Debian users with different board models.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Removed upstreamed:
mvebu/patches-5.4/319-ARM-dts-turris-omnia-configure-LED-2--INTn-pin-as-interrupt-pin.patch
Build system : x86_64
Build-tested : ipq806x/R7800
Run-tested : ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
1. Use upstream accepted NVMEM patches
2. Minor fix for BCM4908 partitioning
3. Support for Linksys firmware partitions on Northstar
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The original GL.iNet firmware has two different mac addresses in the
factory/art partition. The first one is for the WAN interface only and the
second one is for both lan0 and lan1.
But the original submission for OpenWrt didn't initialize the mac
addresses of the LAN ports for the DSA device at all. The ethernet mac
address was then used for all DSA ports.
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The original patch to support this device advertised support for the reset
button and the "switch" in the commit message. But neither were actually
integrated in the device tree or documented anywere.
The button itself is now used to trigger a reset (as described in the
official GL.iNet documentation). The switch itself is registered as BTN_0
like other devices from GL.iNet in ath79.
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
venom has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.
venom uboot however as set from factory will load up to 6MB.
This can be observed by looking a uboot log:
NAND read: device 0 offset 0x900000, size 0x600000
6291456 bytes read: OK
and from uboot environment variables:
$ fw_printenv | grep "priKernSize";
priKernSize=0x0600000
Resize the root partitions from 120MB to 117MB to let kernel expand
into it another 3MB.
And set kernel target size to 6MB.
Lastly set the kernel-size-migration compatibility version on venom to
prevent sysupgrading without first reinstalling from a factory image.
Signed-off-by: Tad Davanzo <tad@spotco.us>
mamba has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.
mamba uboot however as set from factory will load up to 4MB.
This can be observed by looking a uboot log:
NAND read: device 0 offset 0xa00000, size 0x400000
4194304 bytes read: OK
and from uboot environment variables:
$ fw_printenv | grep "pri_kern_size";
pri_kern_size=0x400000
Resize the root partitions from 37MB to 36MB to let kernel expand
into it another 1MB.
And set kernel target size to 4MB.
Lastly add a compatibility version message: kernel-size-migration.
And set it on mamba to prevent sysupgrading without first reinstalling from
a factory image.
Signed-off-by: Tad Davanzo <tad@spotco.us>
Make some cosmetic changes in the Buffalo LinkStation LS421DE NAS:
- Delete pointless #xxx-cells
- bootargs: replace earlyprintk with earlycon and remove unneeded args.
- Separate pinmux nodes with empty lines.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
It's meant to provide upstream support for mtd & NVMEM. It's required
e.g. for reading MAC address from mtd partition content. It seems to be
in a final shape so it's worth testing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Also add a new kconfig symbol (CONFIG_KCMP) to the generic config,
disabling the SYS_kcmp syscall (it was split from
CONFIG_CHECKPOINT_RESTORE, which is disabled by default, so the
previous behaviour is kept).
Removed (upstreamed) patches:
070-net-icmp-pass-zeroed-opts-from-icmp-v6-_ndo_send-bef.patch
081-wireguard-device-do-not-generate-ICMP-for-non-IP-pac.patch
082-wireguard-queueing-get-rid-of-per-peer-ring-buffers.patch
083-wireguard-kconfig-use-arm-chacha-even-with-no-neon.patch
830-v5.12-0002-usb-serial-option-update-interface-mapping-for-ZTE-P685M.patch
Manually rebased patches:
313-helios4-dts-status-led-alias.patch
104-powerpc-mpc85xx-change-P2020RDB-dts-file-for-OpenWRT.patch
Run tested:
ath79 (TL-WDR3600)
mvebu (Turris Omnia)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
5.4.102 backported a lot of stuff that our WireGuard backport already
did, in addition to other patches we had, so those patches were
removed from that part of the series. In the process other patches were
refreshed or reworked to account for upstream changes.
This commit involved `update_kernel.sh -v -u 5.4`.
Cc: John Audia <graysky@archlinux.us>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This adds the latest version of ofpart commit. It hopefully
1. Doesn't break compilation
2. Doesn't break partitioning
(this time).
It's required to implement fixed partitioning with some quirks. It's
required by bcm53xx, bcm4908, kirkwood, lantiq and mvebu.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This patch enables LED support for the GL.iNet GL-MV1000
Signed-off-by: Jeff Collins <jeffcollins9292@gmail.com>
[add SPDX identifier on new file, add aliases, minor cosmetic issues]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
We so far had two variables IMG_PREFIX and IMAGE_PREFIX with
different content. Since these names are obviously quite
confusing, this patch renames the latter to DEVICE_IMG_PREFIX,
as it's a device-dependent variable, while IMG_PREFIX is only
(sub)target-dependent.
For consistency, also rename IMAGE_NAME to DEVICE_IMG_NAME, as
that's a device-dependent variable as well.
Cc: Paul Spooren <mail@aparcar.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
CONFIG_NET_DSA_MV88E6XXX_PTP was simply missing in generic config.
CONFIG_I2C_PXA_SLAVE was previously enabled via i2c-pxa package,
but got removed there without moving the symbol to generic config.
Fixes: dd13add3ce ("kernel: i2c-pxa: remove slave")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add symbol to generic config (this was added between 5.4 and 5.10),
and remove it from the targets where it was added by kernel_oldconfig
in the meantime.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Keep 5.4 as stable until further validation.
Tested on Turris Omnia (Rui Salvaterra) and ESPRESSObin v5 (Tomasz
Maciej Nowak). Cortex-A{53,72} subtargets are only build-tested.
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[added comment about tests]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Enable and fix hardware buffer management. Also fix the IRQ storm caused by a
misconfiguration of the PCA9538 interrupt pin.
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Make each logical patch group numbering contiguous.
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[add kernel version to backport]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Also delete already upstreamed patches/changes.
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Just a simple copy, no refresh yet.
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[do not duplicate files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Remove the implicit/inherited symbols. While not strictly necessary, this will
make reviewing the diff between 5.4 and 5.10 easier.
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
There are proper workarounds merged to 5.4 stable tree for ESPRESSObin
boards with older bootloader:
4e1a23779bde ("ata: ahci: mvebu: Make SATA PHY optional for Armada 3720")
40af962eb1d4 ("usb: host: xhci: mvebu: make USB 3.0 PHY optional for
Armada 3720")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.
Build-tested: bcm27xx/bcm2711, ipq806x/R7800,
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Currently it's not possible to boot the device with just initramfs image
without additional effort as the initramfs image doesn't contain device
tree. Fix it by producing FIT based image which could be booted with
following commands:
setenv bootargs earlyprintk console=ttyS0,115200
tftpboot ${kernel_addr_r} openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin
bootm ${kernel_addr_r}
Acked-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The thermal zones kernel documentation is misleading, we cannot use more
than one sensor in a thermal zone node.
Furthermore the drivetemp driver for some reason it only catches one
sensor from the hard drives array (the first available).
In the Buffalo Linkstation LS421DE board there is also a sensor at the
ethernet phy chip that can also be monitored. Very useful to stop the fan
when there are no hard drives in the bays.
(It might be also possible to add the CPU sensor, but it requires kernel
patching for registering the sensor via device tree, using the function:
devm_thermal_zone_of_sensor_register)
Fix the thermal zones to use only one sensor per node and add the ethernet
phy sensor. Also adjust the hdd temperatures to be more conservative for
a mechanical hard drive.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:
device/image name: vendor_model
compatible: vendor,model
The equal redundant definitions are a symptom of this process.
Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.
This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The following four led triggers are enabled in generic config.
* kmod-ledtrig-default-on
* kmod-ledtrig-heartbeat
* kmod-ledtrig-netdev
* kmod-ledtrig-timer
Drop the packages and remove them from DEVICE_PACKAGES.
There's no other package depending on them in this repo.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Backport the upstream kernel fix 525b0858ff to get rid of the kernel
messages:
mvebu-gpio xxxxxx.gpio: IRQ index 3 not found
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The Buffalo Linkstation LS421DE comes with a Ricoh RS5C372A real time
clock. This RTC has the INTRA pin connected to the power management
circuit, allowing to wake up the device from the power off state when an
alarm is scheduled.
Add the "wakeup-source" property in the RTC dts node to allow the use
of the alarm.
Example of use, the device is powered off and it comes to life after 5
minutes:
echo $(expr $(date '+%s') + 60 * 5) > /sys/class/rtc/rtc0/wakealarm
poweroff
This feature isn't available in the stock firmware.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The Buffalo Linkstation LS421DE isn't able to enable the Level 2 cache
(AKA Aurora cache). As of result of this, the throughput is about half of
the expected, e.g when doing network data transfers.
Fix it by adding the broken-idle property in the coherency fabric node.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
