Commit 5d76065 moved the creation of the symvers directory to
include/kernel-build.mk. This is fine when building from scratch. But
when unpacking an SDK the directory doesn't exist and because the kernel
won't be built (again) this directory will not be created by the build
system, causing build failure if make tries to copy files into it.
This moves the creation of the symvers directory back into
include/kernel.mk so that the directory is created in any case.
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
This patch adds support for the WiFi Pineapple Mark 7, a wireless
penetration testing tool.
Specifications:
* SoC: MediaTek MT7628 (580MHz)
* RAM: 256MiB (DDR2)
* Storage 1: 32MiB NOR (SPI)
* Storage 2: 2GB eMMC
* Wireless 1: 802.11b/g/n 2.4GHz (Built In)
* Wireless 2: 802.11b/g/n 2.4GHz (MT7601)
* Wireless 3: 802.11b/g/n 2.4GHz (MT7601)
* USB: 1x USB Type-A 2.0 Host Port
* Ethernet: 1x USB Type-C AX88772C Ethernet
* UART: 57600 8N1 on PCB
* Inputs: 1x Reset Button
* Outputs: 1x RGB LED
* FCCID: 2AA52MK7
Flash Instructions:
Original firmware is based on OpenWRT.
Use sysupgrade via SSH to flash.
Signed-off-by: Marc Egerton <foxtrot@realloc.me>
[pepe2k@gmail.com: set only required/used gpio groups to gpio function]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
New batches of the R36A board series might no longer keep separated
Ethernet MAC addresses stored in flash. Use same approach as on the
N2Q and calculate Ethernet MACs from WLAN one which is kept in ART.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
ALFA Network Pi-WiFi4 is a Qualcomm QCA9531 v2 based, high-power 802.11n
WiFi board in Raspberry Pi 3B shape, equipped with 1x FE and 4x USB 2.0.
Specifications:
- Qualcomm/Atheros QCA9531 v2
- 650/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16+ MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz Wi-Fi with Qorvo RFFM8228P FEM
- 2x IPEX/U.FL connectors on PCB
- 4x USB 2.0 Type-A
- Genesys Logic GL850G 4-port USB HUB
- USB power is controlled by GPIO
- 5x LED (3x on PCB, 2x in RJ45, 4x driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, enabled by default)
- 1x micro USB Type-B for power and system console (Holtek HT42B534)
- UART and GPIO (8-pin, 1.27 mm pitch) header on PCB
Flash instruction:
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Kernel has separated the structs that are reported to be const in
checkpatch.pl into a file of its own, const_structs.checkpatch.
This file has been missing after the recent update of checkpatch.pl,
leading to the following message:
No structs that should be const will be found - file
'/data/openwrt/scripts/const_structs.checkpatch': No such file
or directory
This commit adds the relevant file from v5.10-rc4.
Fixes: 086ee09bbc ("scripts: Update checkpatch.pl to 2020-06-11")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The kernel expects changes to MAINTAINERS for all removed or added
files, printing warnings like:
WARNING: added, moved or deleted file(s), does MAINTAINERS need updating?
#828:
deleted file mode 100644
Since this does not apply to "our" files in OpenWrt repo, this
warning should be disabled.
This can be achieved easiest by setting $reported_maintainer_file
to 1. While this is a hack that tricks the script into believing
the proper MAINTAINERS changes have been made, it's the easiest
solution as it does not require to touch any other code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Xiaomi Mi Router 4A Gigabit model has a race condition on bootup
causing the SQUASHFS data errors to appear and create a bootloop
scenario.
Adding the m25p,fast-read property resolves this issue.
Suggested-by: David Bentham <db260179@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
CPU: Atheros AR9342 rev 3 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
WLAN 2.4GHz: Atheros AR9342 v3 (ath9k)
WLAN 5.0GHz: QCA988X
Ports: 2x GbE
Flashing procedure is identical to other ubnt devices.
https://openwrt.org/toh/ubiquiti/common
Flashing through factory firmware
1. Ensure firmware version v8.7.0 is installed.
Up/downgrade to this exact version.
2. Patch fwupdate.real binary using
`hexdump -Cv /bin/ubntbox | sed 's/14 40 fe 27/00 00 00 00/g' | \
hexdump -R > /tmp/fwupdate.real`
3. Make the patched fwupdate.real binary executable using
`chmod +x /tmp/fwupdate.real`
4. Copy the squashfs factory image to /tmp on the device
5. Flash OpenWrt using `/tmp/fwupdate.real -m <squashfs-factory image>`
6. Wait for the device to reboot
(copied from Ubiquiti NanoBeam AC and modified)
To keep it consistent, we will add the gen1 variant to
the nanobeam ac gen1.
Signed-off-by: Nick Hainke <vincent@systemli.org>
No special changes, just get in sync with recent code.
See here for the changelog:
https://valgrind.org/docs/manual/dist.news.html
The ipkg sizes changes as follows for mips 24kc :
3.15 : valgrind_3.15.0-2_mips_24kc.ipk 1450680
3.16.1 : valgrind_3.16.1-1_mips_24kc.ipk 1491954
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No special changes, just get in sync with recent code.
See here for the changelog:
https://github.com/strace/strace/releases/tag/v5.9
The ipkg sizes changes as follows for mips 24kc :
5.8 : strace_5.8-1_mips_24kc.ipk 271195
5.9 : strace_5.9-1_mips_24kc.ipk 278352
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No special changes, just get in sync with recent code.
See here for the changelog:
http://software.es.net/iperf/news.html#iperf-3-9-released
The ipkg sizes changes as follows for mips 24kc :
3.7 : iperf3_3.7-1_mips_24kc.ipk 39675
3.9 : iperf3_3.9-1_mips_24kc.ipk 41586
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Avoid needlessly breaking old initscripts that set EXTRA_COMMANDS. This
will aid in debugging (as it simplifies reverting to an older version of
a package) and unbreaks third-party feeds (and packages that maintain
their OpenWrt initscripts as part of the software's repo instead of the
OpenWrt feed like fastd).
Without this, initscripts that set EXTRA_COMMANDS become completely
unusable, as all default commands like start/stop cease working.
Fixes: 1a69f50dc6 ("base-files: fix rc.common help alignment")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This sets the validity interval for the BSS transition candidate
list to the same value as the disassociation timer.
Currently the value is always 0, which is the specification states is a
reserved value. Also, wpa_supplicant and from the looks of it some
Android implementations will outright ignore the candidate list in this
case.
Signed-off-by: David Bauer <mail@david-bauer.net>
* Add support for passing airtime_sta_weight into hostapd configuration.
* Since that commit it is possible to configure station weights. Set higher
value for larger airtime share, lower for smaller share.
I have tested this functionality by modyfing /etc/config/wireless to:
config wifi-device 'radio0'
...
option airtime_mode '1'
config wifi-iface 'default_radio0'
...
list airtime_sta_weight '01:02:03:04:05:06 1024'
Now, when the station associates with the access point it has been assigned
a higher weight value.
root@OpenWrt:~# cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/stations/01\:02\:03\:04\:05\:06/airtime
RX: 12656 us
TX: 10617 us
Weight: 1024
Deficit: VO: -2075 us VI: 256 us BE: -206 us BK: 256 us
[MAC address has been changed into a dummy one.]
Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
airtime_mode is always parsed as an empty string since it hasn't been
added into hostapd_common_add_device_config function.
Fixes: e289f183 ("hostapd: add support for per-BSS airtime configuration")
Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
This adds a new get_status method to a hostapd interface, which
provides information about the current interface status.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds information from mac80211 to hostapd get_client ubus function.
This way, TX as well as RX status information as well as the signal can
be determined.
Signed-off-by: David Bauer <mail@david-bauer.net>
procd-seccomp switched to OCI-compliant seccomp parser instead of our
(legacy, OpenWrt-specific) format. Convert ruleset to new format.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
wireguard-tools is trying to import the menuconfig section
from the wireguard package, but since it's not anymore in
the same makefile this seems to fail and wireguard-tools
ends up in "extra packages" category instead with other
odds and ends.
Same for the description, it's trying to import it from the
wireguard package but it fails so it only shows the line
written in this makefile.
remove the broken imports and add manually the entries
and description they were supposed to load
Fixes: ea980fb9c6 ("wireguard: bump to 20191226")
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
[fix trailing whitespaces, add Fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds a missing ";;" in the switch-case in 11-ath10k-caldata.
Fixes: 4d36569b9c ("ath79: fix ath10k caldata extraction on some
D-Link DIR-842 C3 devices")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
According to forum threads [0][1] and a report on IRC by Doc-Saintly
some of those boards have calibration data in a different place. Only
one alternative location is known.
Without proper board calibration data (board.bin having all 0xff bytes)
ath10k firmware still tries to load but crashes on startup with a
confusing error message.
If you're applying this patch manually on your device do not forget to
remove /lib/firmware/ath10k/pre-cal-pci-0000:00:00.0.bin and reboot to
force caldata re-extraction.
[0] https://forum.openwrt.org/t/support-for-d-link-dir842-rev-c3/41654
[1] https://forum.openwrt.org/t/d-link-dir-842-cant-access-firmware-upload-form/65454
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
All targets that used mvsw61xx have switched to upstream mv88e6xxx DSA
driver, so it can be removed.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
mediatek frequently had mixed indent (tabs vs. spaces) in DTS files
and DTS file kernel patches (probably due to careless copy/paste).
The harmonizes these cases to tabs-only, as usual for DTS(I).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Update dropbear to latest stable 2.81; for the changes see https://matt.ucc.asn.au/dropbear/CHANGES
Refresh patches
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Both bcm2709 and bcm2710 firmware can run on the same RaspberryPi
models, varying however in 32 and 64 Bit architectures. The model name
alone does not include the architecture information, which becomes
problematic if looking at a overview that only contains the names. By
adding a variant it is possible to tell the architecture.
Signed-off-by: Paul Spooren <mail@aparcar.org>
BusyBox ip already provides the required functionality and is enabled by default
in OpenWrt. This patch drops the ip dependency and makes the BusyBox ip required
dependencies explicit, allowing for a significant image size reduction.
openwrt-ath79-generic-ubnt_nanostation-loco-m-squashfs-sysupgrade.bin size:
4588354 bytes (with ip-tiny)
4457282 bytes (with BusyBox ip)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Apple ships a broken make version with the Xcode command line tools.
Homebrew installs make as gmake by default in order to not collide with
Apple's version.
Exit with an error if the broken one is used accidentally
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update iproute2 to latest stable 5.9; for the changes see https://lwn.net/Articles/834755/
Refresh patches
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Acked-by: Hauke Mehrtens <hauke@huake-m.de>
This pci@40000000 node from upstream was dropped when the device
was converted from local DTS(I) files to kernel patches in [1] to
ensure that change was purely cosmetic.
However, the DK04.1 has a PCI-E slot by default, so let's keep
(i.e. not remove) the kernel definition now.
[1] c4beac9ea2 ("ipq40xx: use upstream DTS files for IPQ4019/AP-DK04.1")
Suggested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
A lot of patches are outdated versions of upstreamed patches and
drivers.
So lets pull in the upstreamed patches and reorder remaining ones.
This drops the unnecessary 721-dts-ipq4019-add-ethernet-essedma-node.patch
which adds nodes for not yet in OpenWrt IPQESS driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[do not touch 902-dts-ipq4019-ap-dk04.1.patch here]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Define wildcard patterns for filtering in target/linux/generic/config-filter
Preparation for supporting newer kernels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
