Hardware:
SoC: Lantiq VRX 220
CPU Cores: 2x MIPS 34Kc at 500 MHz
RAM: 128 MiB 250 MHz
Storage: 128 MiB NAND flash
Ethernet: built-in Fast Ethernet switch, only port 2 is used
Wireless: Atheros AR9287-BL1A b/g/n with 2 pcb antennas
Modem: built-in A/VDSL2 modem
DECT: Dialog SC14441
LEDs: 1 two-color, 4 one-color
Buttons: 2
FXS: 1 port via TAE or RJ12 connector
Everything except FXS/DECT works
(no drivers for AVM's FXS implementation with SC14441).
Installation:
Use the eva_ramboot.py script to load an initramfs image on the
device. Run it a few seconds after turning the device on.
$ scripts/flashing eva_ramboot 192.168.178.1 bin/targets/lantiq/xrx200/openwrt-lantiq-xrx200-avm_fritz7412-initramfs-kernel.bin
If it fails to find the device try the ip address 169.254.120.1.
(Firmware updates or the recovery tool apparently change it.)
IMPORTANT: set lzma compression in ramdisk options, bootloader stalls
when receiving uncompressed images.
The device will load it in ram and boot it. You can reach it under
the openwrt default ip address 192.168.1.1.
Check if the key linux_fs_start is not set to 1 in tffs:
$ fritz_tffs_nand -d /dev/mtd1 -n linux_fs_start
If it is set to 1, the bootloader will select the wrong set of
partitions. Restart the box and install an FritzOS upgrade or do a
recovery. Afterwards start again at step 1.
Run sysupgrade to persistently install OpenWRT.
Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.de>
Signed-off-by: Andy Binder <AndyBinder@gmx.de>
The current snapshot release kernel with it's 2119245 Byte
size is too big to fit into the 2097152 (2MiB) area that
was set aside for the kernel. Which causes the device to
fail to boot (after an update or even during a fresh install)
NAND read: device 0 offset 0x60000, size 0x200000
2097152 bytes read: OK
## Booting kernel from Legacy Image at 80800000 ...
Image Name: MIPS OpenWrt Linux-4.14.98
Created: 2019-02-13 9:37:36 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2119245 Bytes = 2 MiB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... Bad Data CRC
ERROR: can't get kernel image!
This patch fixes the problem by enlarging the kernel partition
at the cost of the ubi/data partition behind it. The patch
also adds a KERNEL_SIZE variable to the image Makefile to
prevent silent corruptions from happening in the future.
Please note: The u-boot environment for the router also
needs to be updated. So please attach an appropriate
serial converter cable and enter the following commands
into the u-boot prompt:
setenv nboot 'nand read 0x80800000 0x60000 0x300000; bootm 0x80800000'
saveenv
The wiki has been updated accordingly:
<https://openwrt.org/toh/zyxel/p2812hnu-f1>
Fixes: FS#2124
Suggested-by: Mafketel (User on bugs.openwrt.org)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Enable support for 2nd USB port, which is available on Fritz!Box 7320
and 7330. It was run-tested on 7320 and 7330 as well.
Signed-off-by: Robert Resch <openwrt@webnmail.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit changes the model string and device title of all AVM boards
to fit the naming of the manufacturer.
Drop all provider-specific titles as they are re-used for every device
generation by 1&1. The original AVM model name is printed on the bottom
of every devices.
Exception applies for boards which are only supported by a specific
sub-revision.
Signed-off-by: David Bauer <mail@david-bauer.net>
>From the Documentation/devicetree/bindings/leds/common.txt:
- default-state : The initial state of the LED. Valid values are "on", "off",
and "keep". If the LED is already on or off and the default-state property is
set the to same value, then no glitch should be produced where the LED
momentarily turns off (or on). The "keep" setting will keep the LED at
whatever its current state is, without producing a glitch. The default is
off if this property is not present.
So setting the default-state of the LEDs to `off` is redundant as `off`
is default LED state anyway. We should remove it as almost every new
PR/patch submission contains this property by default which seems to be
just copy&paste from some DTS file already present in the tree.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
- fix single spaces hidden by a tab
- replace indentation with spaces by tabs
- make empty lines empty
- drop trailing whitespace
- drop unnecessary blank lines
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Indicate a (sys)upgrade via leds as well. It brings the lantiq diag.sh
script en par with the other implementations using devicetree aliases
to define multiple leds for boot status indication.
By default, use the boot finished led to indicate an upgrade for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The FritzBox 7312 is also known as 1&1 WLAN-MODEM. The device is almost
the same as FB7330, but only one ETH-Port and no USB.
Hardware
SoC: Lantiq Xway ARX188 PSB 50812 EL
RAM: 64MB DDR1 (Zentel A4S12D40FTP-G5)
Ethernet: Atheros 8030
Wireless: Atheros AR9227 b/g/n 2x2
DSL: Lantiq ADSL2+
DECT: Dialog SC14441
Buttons: WiFi, DECT
LEDs: Power/DSL, Fon, DECT, WLAN, Info
LEDs
Power: GPIO#44 (active low)
Internet: GPIO#47 (active low)
DECT: GPIO#38 (active low)
WLAN: GPIO#37 (active low)
Info: GPIO#35 (active low)
The Fon LED is labeled as internet in avm gpl sources.
Buttons
WLAN: GPIO#1 (active low)
DECT: GPIO#2 (active low)
Phy
GPIO#03: 25 MHz
GPIO#34: Reset (active low)
GPIO#39: Int
GPIO#42: MII MDIO
GPIO#43: MII MDC
PCIe
GPIO#21: reset (active low)
Installation:
To install OpenWrt via Eva bootloader, within the first seconds after
power on a ftp connection need to be established to the FRITZ!Box at
192.168.178.1 and the the following ftp commands need to be run:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put /path/to/openwrt-lantiq-xway-avm_fritz7312-squashfs-sysupgrade.bin mtd1
ftp> quote REBOOT
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
Increase the available flash memory size in AVM Fritz!Box 3370 by
incorporating the unused extra partitions located after the ubi partition.
Note that users upgrading from a previous OpenWRT version need to
re-install from the boot loader to pick up the new partition layout.
Available flash space for rootfs+overlay increases from 48MB to 124MB.
Reverting to the OEM firmware is still possible (via the recovery utility
provided by AVM) as the OEM firmware appears to reformat the config and
nand-filesystem partitions upon first boot if necessary. The
reserved-kernel and reserved-filesystem partitions are overwritten by the
OEM firmware when installing an update, so their contents do not matter.
Boot loader and device-specific information (MAC addresses, calibration
data, etc.) are not located in NAND flash and remain unharmed by this
changed.
Tested with OEM firmware 06.54 on device with HWRevision 5 and Micron
flash chip.
Signed-off-by: Michael Kuron <m.kuron@gmx.de>
It isn't a phy supply, as the phy is still up if the GPIO is low. It
rather is the supply for the vbus. A correct setting/definition will be
relevant as soon as USB peripheral mode is supported.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Rename the image and use a compatible string which indicates that only
hardware revision 2 and higher is supported.
It allows to use the wireless LED, as HWRev 1 uses GPIO#39 for the
wireless LED and starting with HWRev 2 GPIO#35 is used for the wireless
LED and GPIO#39 for IFX_GPIO_MODULE_EXTPHY_MDIO.
The HWREV can be checked by connecting to the fritzbox right after power
on via ftp:
ftp> quote GETENV HWSubRevision
Within the same HW revision 5 of the Fritz!Box 3370 different NAND flash
chips are used. Usually it isn't a big deal but depending on the used
NAND flash chip, the ECC calculation is done different (and incompatible
of course).
Boards with a Micron MT29F1G08ABADA NAND flash chip are using the NAND
chip to calculate the ECC (on-die). Boards with a Hynix HY27UF081G2M NAND
flash chip are doing the ECC calculation in software.
Supporting both with a single DTS isn't possible. It might be possible
to add a patch selecting the ECC mode dynamicaly based on the found NAND
flash chip. But such a patch has no chance to get accepted upstream and
most likely need to be touched with every kernel update.
Instead two images are created. One for Micron NAND flash chip and one
for Hynix NAND flash chip. So far no pattern is known to identify the
used flash chip without opening the box.
Add the power off GPIO. At least EVA version 2186 sets/keeps the GPIO as
input, which will cause a reboot 30sec after power on. For boards with
EVA version 2186 the installation is tricky as it has to be finished
within the 30sec time frame.
The EVA version can be checked by connecting to the fritzbox right after
power on via ftp:
ftp> quote GETENV urlader-version
The ath9k eeprom/caldata is at a different and offset and stored in
reverse order (from the last byte to the beginning) on the flash.
Reverse the bits to bring the data into the format expected by the
ath9k driver.
Since the ath9k eeprom is stored in reverse order on flash, we can not
use the mac address from the on flash eeprom. Get the MAC address from
the tffs instead.
Within the same HW revision 5 of the Fritz!Box 3370 both version of the
vr9 SoC are used. During preparation of kernel 4.14 support, all
devicetree source files were changed to load the vr9 v1.1 and vr9 v1.2
gphy firmware, which fixed the embedded phys for boards using the
version 1.2 of the vr9 SoC.
While at it, add a trigger to make use of the LAN LED. Setup the
build-in switch and add a hint for LuCI two show the ports in order
matching the labels on the case
Add support for the second USB port and provide the volatage GPIOs. Use
GPIO#21 as PCIe reset pin. The lan led is connected to GPIO#38.
Name the rootfs partition ubi and remove the mtd/rootfs related kernel
bootargs to use the OpenWrt autoprobing based on the partition name.
Enable sysupgrade support to allow an upgrade from a running system.
Since sysupgrade wasn't supported till now, drop image build code which
was added to allow a sysupgrade from earlier OpenWrt versions.
Build images that allow an (initial) installation via EVA bootloader.
To install OpenWrt via Eva bootloader, within the first seconds after
power on a ftp connection need to be established to the FRITZ!Box at
192.168.178.1 and the the following ftp commands need to be run:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote SETENV linux_fs_start 0
ftp> quote MEDIA FLSH
ftp> put /path/to/openwrt-lantiq-xrx200-FRITZ3370-eva-kernel.bin mtd1
ftp> put /path/to/openwrt-lantiq-xrx200-FRITZ3370-eva-filesystem.bin mtd0
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
We need to reset the GPHYs on reboot as well. Otherwise the bootloader
might have issues to reset/find the GPHYs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Lantiq XRX200 aka VR9 doesn't have an asc0. Instead,
there is an USIF module which can either be an UART or a
SPI Controller.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Updated the devicetree source files to make use of the following
upstreamed drivers:
- xrx200 ethernet phy
- reset controller unit
- dwc2
- fpi
Use our custom xrx200 ethernet phy compatible to support boards, which
have switched the vr9 revision during lifetime, with a single devicetree
source file.
By switching to the dwc2 driver + usb phy framework, we don't need to used
our custom gpio power patch and can use a fixed regulator instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This just copies the patches, configuration and dts files into the
directories hich are used for kernel 4.14.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
