Using OKLI image to fix the booting stuck issue.
Tested with u-boot extracted from TP-Link stock images
"RE200(EU)_V1_171206.zip" and "RE210(US_CA)_V1_171205.zip".
Fixes: https://github.com/openwrt/openwrt/issues/16296
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16473
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b62e6f5beb2a574c67ba5159f0049e54cdf25d69)
This commit adds support for netis N6 WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (ESMT PSU1GA30DT)
- WLAN : MT7905DAN + MT7975DN
- 2.4 GHz : b/g/n/ax, 574 Mbps, MIMO 2x2
- 5 GHz : a/n/ac/ax, 1201 Mbps, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x5 (1x WAN, 4x LAN)
- USB : 1x 3.0
- UART : 3.3V, 115200n8
- Buttons : 1x Reset
1x WPS
- LEDs : 1x Power (green)
1x System (green)
1x WAN (green)
1x WiFi 2.4 GHz (green), controlled by phy
1x WiFi 5 GHz (green), controlled by phy
1x WPS (green)
1x USB (green)
5x ethernet leds (green), controlled by switch
- Power : 12 VDC, 1.5 A
Installation
------------
1. Update the router using stock firmware web interface and OpenWrt
factory.bin image.
Recovery and return to stock
----------------------------
1. Assign your PC a static IP 192.168.1.2 and connect to the router using
the ethernet cable;
2. Power off the router;
3. Press Reset button, power on the router and wait until ethernet led
start blinking;
4. Release the button;
5. Open http://192.168.1.1/ (N6 System Recovery Mode) in your browser;
6. Upload OpenWrt factory.bin (or stock firmware *.bin) image and proceed
with upgrade.
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LAN | dc:xx:xx:49:xx:04 |
| WAN | dc:xx:xx:49:xx:05 |
| WLAN 2g | dc:xx:xx:19:xx:06 |
| WLAN 5g | dc:xx:xx:79:xx:06 |
+---------+-------------------+
The WLAN MAC prototype was found in 'Factory', 0x4
The LAN MAC was found in 'Factory', 0x7ef20
The WAN MAC was found in 'Factory', 0x7ef26
Known issue
-----------
2.4 GHz WLAN doesn't start with mt76 driver.
Probable reason:
Original Netis N6 EEPROM contains wrong MT_EE_WIFI_CONF value (0xd2).
Other routers with the same WLAN hardware (e.g., Routerich AX1800)
have MT_EE_WIFI_CONF = 0x92.
Workaround (already included in this commit):
Extract EEPROM to a file at the first time boot and change
MT_EE_WIFI_CONF (offset 0x190) value from 0xd2 to 0x92. See
/etc/hotplug.d/firmware/11-mt76-caldata for details.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
(cherry picked from commit f368e2d5ece1153ec242872f3c48991ed225d9b7)
[ Fix merging onflicts in mt7621.mk, 10_fix_wifi_mac, platform.sh ]
[ Change ðphy4 -> &mdio in dts file ]
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16436
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
...conversion.
Commit 20736013e910 ("kernel: backport nvmem v6.6 fixes and v6.7 changes")
has caused dthe device to no longer correctly read MAC address from its
onboard 24c64 EEPROM, because "at24" driver doesn't support legacy
nvmem-cell bindings [1] - and there was an explicit config option added
to mandate that behaviour in the following patch:
820-v6.7-0002-nvmem-add-explicit-config-option-to-read-old-syntax-.patch
But some of the devices, MR33 and MR74 included, weren't converted with
that as well.
Convert the definition to use proper fixed-layout binding to fix it.
The offending change was introduced between v23.05.0 and v23.05.1, and
found by bisection:
git bisect start
# status: waiting for both good and bad commits
# good: [bd4f415efacfc03bbe5b79ae1d39c1451f5f7385] OpenWrt v23.05.0: adjust config defaults
git bisect good bd4f415efacfc03bbe5b79ae1d39c1451f5f7385
# status: waiting for bad commit, 1 good commit known
# bad: [a58a86693f8593974ff7c26bb42e280b62a8724c] OpenWrt v23.05.1: adjust config defaults
git bisect bad a58a86693f8593974ff7c26bb42e280b62a8724c
# good: [3d0a78add22754aa891529b6702b5e4c7b837446] qualcommax: only build initramfs if CONFIG_TARGET_ROOTFS_INITRAMFS is set
git bisect good 3d0a78add22754aa891529b6702b5e4c7b837446
# bad: [21e5db97c410f4008c8fe8515fb79a7cde368dbf] build: add CycloneDX SBOM JSON support
git bisect bad 21e5db97c410f4008c8fe8515fb79a7cde368dbf
# good: [89184b15cfce4aaffac8cda87c2fa74f829ace42] mediatek: add build for MT7981 RFB
git bisect good 89184b15cfce4aaffac8cda87c2fa74f829ace42
# bad: [41f27bbb6d0af2f37098b97cd28d5f514a6fc417] bcm53xx: add the latest fix version of brcm_nvram
git bisect bad 41f27bbb6d0af2f37098b97cd28d5f514a6fc417
# good: [b649b0bf7100bdc6adb7e857c74738cab7c47b4c] kernel: nvmem: fix "fixed-layout" & support "mac-base"
git bisect good b649b0bf7100bdc6adb7e857c74738cab7c47b4c
# bad: [20736013e91030005353b401bc4b757ba5e5fa98] kernel: backport nvmem v6.6 fixes and v6.7 changes
git bisect bad 20736013e91030005353b401bc4b757ba5e5fa98
# good: [066971615ff66512bc542b09a90be34c2afe98bb] kernel: backport v6.6 nvmem changes
git bisect good 066971615ff66512bc542b09a90be34c2afe98bb
# first bad commit: [20736013e91030005353b401bc4b757ba5e5fa98] kernel: backport nvmem v6.6 fixes and v6.7 changes
Link: [1] https://github.com/openwrt/openwrt/issues/15393#issuecomment-2212300849
Fixes: 20736013e910 ("kernel: backport nvmem v6.6 fixes and v6.7 changes")
Fixes: https://github.com/openwrt/openwrt/issues/15393
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit ccbffad1ad0ce444bc2497098a1d3d3a086a5f44)
[replace mac-address-increment with #nvmem-cell-cells]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16624
Signed-off-by: Robert Marko <robimarko@gmail.com>
er is missing from platform_copy_config() and octeon_move_config(), so
config is lost on every sysupgrade.
(cherry-picked from commit 77037b09f3ce3284c8486b73cfaaceac53241990)
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Link: https://github.com/openwrt/openwrt/pull/16518
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, bzip2 is built with a dynamically linked library on which all
of the bzip2 tools depend on.
However, when trying to use the staging dir bzip2 during building on
Fedora 40 the following error appers:
staging_dir/host/bin/bzip2: error while loading shared libraries: libbz2.so.1.0: cannot open shared object file: No such file or directory
Looking into it, the binary is dynamically linked:
$ ldd staging_dir/host/bin/bzip2
linux-vdso.so.1 (0x00007f5ebd9ff000)
libbz2.so.1.0 => not found
libc.so.6 => /lib64/libc.so.6 (0x00007f5ebd7f5000)
/lib64/ld-linux-x86-64.so.2 (0x00007f5ebda01000)
libbz2.so.1.0 is installed into staging_dir/lib but that directory is not
evaluated for the required libraries and Fedora only ships:
/usr/lib64/libbz2.so.1
/usr/lib64/libbz2.so.1.0.8
Thus it cannot find the libbz2 that bzip2 is linked against and thus
trying to use bzip2 will fail and stop compilation as it is used for
bzip2 compressed tarballs.
So, to avoid OpenWrt compiled bzip2 to even attempt to load a required
library from the host we can just static compile libbz2 and bzip2.
Link: https://github.com/openwrt/openwrt/pull/16520
Signed-off-by: Robert Marko <robimarko@gmail.com>
The rss variant should conflict with the default.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/16460
(cherry picked from b83c7448d3ecd82d6c9e02aded784d6bc3c9ce3c)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The rss variant should conflict with the default.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/16460
(cherry picked from d39078c785d37961e8b9a96ba3612bc67c10bf2f)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Building a package in the build system or the SDK results in different
values for the `SOURCE` property, it's either `packages/<package name>`
or `feeds/base/<package name>`. The reason is that the SDK handles
`openwrt.git` as an external feed called while the build system contains
the *base* packages directly.
Since packages created with either method are (ideally) the same (bit
for bit), align the content of SOURCE. To do so this commit creates a
symlink from `feeds/base` to `$(TOPDIR)/package` and adopts the SOURCE
when building from inside the build system.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The MAC address of the GMAC is contained inside the CWMP-Account
number on the label.
The label MAC address alias was defined previously, but it has been
removed with the switch to IPQESS / DSA.
Restore the label MAC address alias.
Fixes: 27b441cbaf42 ("ipq40xx: drop ESSEDMA + AR40xx DTS nodes")
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit b22d382ae4eaa1af42930115d91855f402314cac)
Signed-off-by: Tom Herbers <mail@tomherbers.de>
Link: https://github.com/openwrt/openwrt/pull/16459
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With commit a22d359fa56fe0 VLAN handling was fixed for kernel 6.6.
This restored network connectivity of the devices. For easy testing
backport the fix for 5.15 too.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16391
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 35e13244aab36958831195a1d2e152aa3ad0ab6c)
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Change I2C pin flags to GPIO_ACTIVE_HIGH and change SDA to GPIO1.
On my late production GL-AR750 (purchased 2024):
SCL = GPIO16
SDA = GPIO1
Bug report:
I2C bus doesn't work in GL-AR750
https://github.com/openwrt/openwrt/issues/16319
Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16406
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 2e626ae2d2488f2d3708d3aed57eea7a1402f00e)
Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The sysupgrade-tar image build is not defined for this target, do not
add a build instruction for it. The build system will use the definition
from the dna_valokuitu-plus-ex400 board and the build will fail.
This fixes the build of the ramips target.
Fixes: 665c2154ef12 ("ramips: add basic support for tp-link er605-v2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 746e894877e5130a7d5227cd90f90dfe18cc274b)
The previous host installation fix accidentally moved the rpath settings
out of CMAKE_HOST_OPTIONS and into CMAKE_OPTIONS.
Fixes: ae42ecaad4e7 ("ucode: fix host installation")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 2ee1392e094f9b6fdb2a759e2e29fa203b61e066)
Add the GPIO pin of the PoE passthrough switch on the Aruba AP-303H.
Power is activated when the pin is low. It enables a PSE chip, so power
is only supplied to downstream devices when they are 802.3af/at
compliant devices.
Ensure you use a sufficient power supply when chaining a consuming
device after the AP.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b40cc46cc882ff97f2752e7837173ffc9f884eb9)
This fixes a well-known "LZMA ERROR 1" error on Sercomm NA502s, reported
on the OpneWrt forum [0].
[0] https://forum.openwrt.org/t/206640
Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit 6d89aa29878a93c744e8c752a68bc05d41252cfc)
Link: https://github.com/openwrt/openwrt/pull/16412
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Because these capability advertisements default to on in lldpd, they
became absent at reload, and not restart, due to how the reload logic
works ( keep daemon running, send unconfigured and then the new config
via socket ), and it was not evident unless you happened to be looking
for it (e.g. via pcap or tcpdump). It was also not evident from the
manpage ( have now sent patches upstream ).
At reload time, the unconfigure logic disabled them unless they were
explicitly enabled (compare with other settings where 'unconfigure' just
resets them). Now they default to on/enabled at init time, and are
explicitly 'unconfigure'd at startup if the user disables them via:
lldp_mgmt_addr_advertisements=0
lldp_capability_advertisements=0
In other words: explicit is necessary to disable the advertisements.
The same applies to 'configure system capabilities enabled'. Technically
'unconfigure'd is the default but now it is explicit at reload.
Tested on: 23.05.3
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
(cherry picked from commit 708101c1412c42c7fb1d838024513a34424c50ff)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
For interface type parameters, the man page documents patterns:
```
*,!eth*,!!eth1
uses all interfaces, except interfaces starting with "eth",
but including "eth1".
```
* Renamed `_ifname` to `_l2dev`.
* get the l2dev via network_get_physdev (and not l3dev)
* Glob pattern `*` is also valid - use noglob for this
The net result is that now interface 'names' including globs '*' and '!'
inversions are included in the generated lldpd configs.
Temporarily `set -o noglob` and then `set +o noglob` to disable & enable
globbing respectively, because when we pass `*` as an interface choice,
other file and pathnames get sucked in from where the init script runs,
and the `*` never makes it to lldpd.
Tested extensively on: 22.03.6, 23.05.3
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
[ squash with commit bumping release version ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 4a81d868db85a7954a73bc6dc4a957bbd6abc813)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
Defaults to off.
Available from >= 0.7.15
These are sent in TLV
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
(cherry picked from commit 50021d3222667a9a239451de0422f0508aef4419)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
Defaults to off.
Only available from >= 1.0.15
These capabilities are sent in TLV.
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
(cherry picked from commit 4d8f56bd59f457fd815e2bb4f87df8c7dad2d4fd)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
only available from >= 1.0.15
Comments are useful. Apparently this config parameter was committed when
openwrt used an older version of lldpd which did not yet support it.
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
(cherry picked from commit b4769175029ad23833b21960d1b605f629537ad7)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
update Makefile URL
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit f753d3152f81bd037e9b7abb1b8c5bf9fe54596b)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
No functionality/behaviour changes; code is synonymous
Tested on: 22.03.6
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 5364fe0f01ca11b47c55d78f756d3176748dd0c2)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
For certain lldp_class scenarios (2 & 3) a policy must be set also.
Class 4 is default, although it's good to handle the policy eventuality.
Here, set a default lldp_policy for all lldp_class scenarios. Any
lldp_policy can now be set.
Depends on PR #14584 (which introduced an `if` block)
Tested on 22.03.5, 22.03.6
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 497fafb8aea48e764ce0e456f20ab346691e585f)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
Previously only partially implemented. After commit
5007f488bb5e1b556052ef246bd3822fed8d09d2 lldp_location was never removed
Now, add the value of lldp_location to the generated config.
The location param has a few syntaxes, so the config acquires the first
usage from the man page: 'address country EU'
Supplementary fix for PR #14193 (this param was included in the original
PR #13018 but the lldp_location fixes were absent from PR #14193).
Tested on 22.03.5, 22.03.6
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 53252eeb3b6177b77e23235436b04818a88eafe0)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
from commit 3ce909914a12647bec52bcee0a162dd6d158a4f6
The lldpd man page says that "configure lldp tx-interval" can
specify an interval value in milliseconds by appending a "ms" suffix to
the figure. Thus mandating string handling, and not integer comparison.
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 79ee4cb0397eb9eae34369e33d66b5a1d837a652)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
from commit 909f0630663d7ae1471c76154516e3299992a150
Now pass two params to get_config_cid_ifaces() for:
cid_interface
interface
Each of which is a CSV of interfaces.
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 228d4e7f1b759c11897043dc73ef3c576bc13f7f)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
from commit a5f715da713304972467612d6934130ce3aa2837
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 4dcece46a7b4ede7d05d8fb9d31d62406bca74d0)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
from commit ac771313ebedd2c4bfda8adef47650d45d77c32d
portidsubtype takes 1 of 2 possible keywords which do not need quoting:
configure lldp portidsubtype ifname | macaddress
The third keyword 'local' is used in the syntax when individual ports
are being defined:
configure [ports ethX [,…]] lldp portidsubtype local value
When this syntax is used, quoting is useful (see test cases for lldpd).
In the init file, the 'local' syntax is unused.
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit bd1b17d589bc622408cebdd9fa0f43386cc3ef5a)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
from commit c98ee4dbb3db0f064d990941cdd82e872da76946
agent-type takes 1 of 3 possible keywords which do not require quoting:
configure lldp agent-type nearest-bridge | nearest-non-tpmr-bridge
| nearest-customer-bridge
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 24a4da527f7e70d9916439a78298de2f4e4af653)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
from commit 3ce909914a12647bec52bcee0a162dd6d158a4f6
'capabilities enabled x' where x is a string of CSV
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit b039641071b1e9ee9654513ef3229bb97cc379af)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
from commit 3ce909914a12647bec52bcee0a162dd6d158a4f6
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 82ec853284e44fb85ad702879d18857bd566c7db)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
from commit 24176a6bdd8f26040a97960868fd0d9ee968d695
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 20a4dddeb0366a56c14f9128392ffe8d0b62e32d)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
from commit 1be2088a5247b2cfabe8be991c1e52ddaf780a16
The original PR #13018 did not exhibit this.
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 4fb8fea6de363aeeeca029ed9801b85cdbf45f0c)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
Supplementary fix for PR #14193
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 1909b6f8835c1381f859c85394defe993e016edd)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
Supplementary fix for PR #14193 and commit
b67182008fd124706be0ec3ce67347447554ffd5
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 97eb3bf76c17328f80554e6a3603de00d835e4c5)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
allow EDP support if compiled and add force EDP option
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit d274867c217cade795537af93ff9b209e472e19c)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
prevent SNMP options being passed unless lldpd supports them
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 8b2d02e48cd2559a52e1cbf04143028e50da6a88)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
increment Makefile package release to reflect changes to init script
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 1b36d44323cdd467980f83318be0837b8a1fd487)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
add option to set LLDP transmit delay, hold timers to set update frequency
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit a5f715da713304972467612d6934130ce3aa2837)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
add option to override system platform instead of using kernel name
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 4159acceebeec646fb2ebecdd85561ba140f1ce4)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
add option to force SONMP to be enabled even when no peer detected
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 4ac134aa78d2b4441b0afd485d1d26dbd53d7276)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
add option to force FDP when no peers detected
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 1be2088a5247b2cfabe8be991c1e52ddaf780a16)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
add option to specify CDPv1 or CDPv2 and separately enable or force each
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit b67182008fd124706be0ec3ce67347447554ffd5)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
add option to allow LLDP disabling while using other supported protocols
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 61dbe756d8edc1adcd152920f71d6dce26232662)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
