This commit adds support for netis N6 WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (ESMT PSU1GA30DT)
- WLAN : MT7905DAN + MT7975DN
- 2.4 GHz : b/g/n/ax, 574 Mbps, MIMO 2x2
- 5 GHz : a/n/ac/ax, 1201 Mbps, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x5 (1x WAN, 4x LAN)
- USB : 1x 3.0
- UART : 3.3V, 115200n8
- Buttons : 1x Reset
1x WPS
- LEDs : 1x Power (green)
1x System (green)
1x WAN (green)
1x WiFi 2.4 GHz (green), controlled by phy
1x WiFi 5 GHz (green), controlled by phy
1x WPS (green)
1x USB (green)
5x ethernet leds (green), controlled by switch
- Power : 12 VDC, 1.5 A
Installation
------------
1. Update the router using stock firmware web interface and OpenWrt
factory.bin image.
Recovery and return to stock
----------------------------
1. Assign your PC a static IP 192.168.1.2 and connect to the router using
the ethernet cable;
2. Power off the router;
3. Press Reset button, power on the router and wait until ethernet led
start blinking;
4. Release the button;
5. Open http://192.168.1.1/ (N6 System Recovery Mode) in your browser;
6. Upload OpenWrt factory.bin (or stock firmware *.bin) image and proceed
with upgrade.
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LAN | dc:xx:xx:49:xx:04 |
| WAN | dc:xx:xx:49:xx:05 |
| WLAN 2g | dc:xx:xx:19:xx:06 |
| WLAN 5g | dc:xx:xx:79:xx:06 |
+---------+-------------------+
The WLAN MAC prototype was found in 'Factory', 0x4
The LAN MAC was found in 'Factory', 0x7ef20
The WAN MAC was found in 'Factory', 0x7ef26
Known issue
-----------
2.4 GHz WLAN doesn't start with mt76 driver.
Probable reason:
Original Netis N6 EEPROM contains wrong MT_EE_WIFI_CONF value (0xd2).
Other routers with the same WLAN hardware (e.g., Routerich AX1800)
have MT_EE_WIFI_CONF = 0x92.
Workaround (already included in this commit):
Extract EEPROM to a file at the first time boot and change
MT_EE_WIFI_CONF (offset 0x190) value from 0xd2 to 0x92. See
/etc/hotplug.d/firmware/11-mt76-caldata for details.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
(cherry picked from commit f368e2d5ec)
[ Fix merging onflicts in mt7621.mk, 10_fix_wifi_mac, platform.sh ]
[ Change ðphy4 -> &mdio in dts file ]
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16436
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
...conversion.
Commit 20736013e9 ("kernel: backport nvmem v6.6 fixes and v6.7 changes")
has caused dthe device to no longer correctly read MAC address from its
onboard 24c64 EEPROM, because "at24" driver doesn't support legacy
nvmem-cell bindings [1] - and there was an explicit config option added
to mandate that behaviour in the following patch:
820-v6.7-0002-nvmem-add-explicit-config-option-to-read-old-syntax-.patch
But some of the devices, MR33 and MR74 included, weren't converted with
that as well.
Convert the definition to use proper fixed-layout binding to fix it.
The offending change was introduced between v23.05.0 and v23.05.1, and
found by bisection:
git bisect start
# status: waiting for both good and bad commits
# good: [bd4f415efa] OpenWrt v23.05.0: adjust config defaults
git bisect good bd4f415efa
# status: waiting for bad commit, 1 good commit known
# bad: [a58a86693f] OpenWrt v23.05.1: adjust config defaults
git bisect bad a58a86693f
# good: [3d0a78add2] qualcommax: only build initramfs if CONFIG_TARGET_ROOTFS_INITRAMFS is set
git bisect good 3d0a78add2
# bad: [21e5db97c4] build: add CycloneDX SBOM JSON support
git bisect bad 21e5db97c4
# good: [89184b15cf] mediatek: add build for MT7981 RFB
git bisect good 89184b15cf
# bad: [41f27bbb6d] bcm53xx: add the latest fix version of brcm_nvram
git bisect bad 41f27bbb6d
# good: [b649b0bf71] kernel: nvmem: fix "fixed-layout" & support "mac-base"
git bisect good b649b0bf71
# bad: [20736013e9] kernel: backport nvmem v6.6 fixes and v6.7 changes
git bisect bad 20736013e9
# good: [066971615f] kernel: backport v6.6 nvmem changes
git bisect good 066971615f
# first bad commit: [20736013e9] kernel: backport nvmem v6.6 fixes and v6.7 changes
Link: [1] https://github.com/openwrt/openwrt/issues/15393#issuecomment-2212300849
Fixes: 20736013e9 ("kernel: backport nvmem v6.6 fixes and v6.7 changes")
Fixes: https://github.com/openwrt/openwrt/issues/15393
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit ccbffad1ad0ce444bc2497098a1d3d3a086a5f44)
[replace mac-address-increment with #nvmem-cell-cells]
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16624
Signed-off-by: Robert Marko <robimarko@gmail.com>
er is missing from platform_copy_config() and octeon_move_config(), so
config is lost on every sysupgrade.
(cherry-picked from commit 77037b09f3)
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Link: https://github.com/openwrt/openwrt/pull/16518
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, bzip2 is built with a dynamically linked library on which all
of the bzip2 tools depend on.
However, when trying to use the staging dir bzip2 during building on
Fedora 40 the following error appers:
staging_dir/host/bin/bzip2: error while loading shared libraries: libbz2.so.1.0: cannot open shared object file: No such file or directory
Looking into it, the binary is dynamically linked:
$ ldd staging_dir/host/bin/bzip2
linux-vdso.so.1 (0x00007f5ebd9ff000)
libbz2.so.1.0 => not found
libc.so.6 => /lib64/libc.so.6 (0x00007f5ebd7f5000)
/lib64/ld-linux-x86-64.so.2 (0x00007f5ebda01000)
libbz2.so.1.0 is installed into staging_dir/lib but that directory is not
evaluated for the required libraries and Fedora only ships:
/usr/lib64/libbz2.so.1
/usr/lib64/libbz2.so.1.0.8
Thus it cannot find the libbz2 that bzip2 is linked against and thus
trying to use bzip2 will fail and stop compilation as it is used for
bzip2 compressed tarballs.
So, to avoid OpenWrt compiled bzip2 to even attempt to load a required
library from the host we can just static compile libbz2 and bzip2.
Link: https://github.com/openwrt/openwrt/pull/16520
Signed-off-by: Robert Marko <robimarko@gmail.com>
The rss variant should conflict with the default.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/16460
(cherry picked from b83c7448d3)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The rss variant should conflict with the default.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/16460
(cherry picked from d39078c785)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Building a package in the build system or the SDK results in different
values for the `SOURCE` property, it's either `packages/<package name>`
or `feeds/base/<package name>`. The reason is that the SDK handles
`openwrt.git` as an external feed called while the build system contains
the *base* packages directly.
Since packages created with either method are (ideally) the same (bit
for bit), align the content of SOURCE. To do so this commit creates a
symlink from `feeds/base` to `$(TOPDIR)/package` and adopts the SOURCE
when building from inside the build system.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The MAC address of the GMAC is contained inside the CWMP-Account
number on the label.
The label MAC address alias was defined previously, but it has been
removed with the switch to IPQESS / DSA.
Restore the label MAC address alias.
Fixes: 27b441cbaf ("ipq40xx: drop ESSEDMA + AR40xx DTS nodes")
Signed-off-by: Fabian Bläse <fabian@blaese.de>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit b22d382ae4)
Signed-off-by: Tom Herbers <mail@tomherbers.de>
Link: https://github.com/openwrt/openwrt/pull/16459
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With commit a22d359fa5 VLAN handling was fixed for kernel 6.6.
This restored network connectivity of the devices. For easy testing
backport the fix for 5.15 too.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16391
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 35e13244aa)
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
The sysupgrade-tar image build is not defined for this target, do not
add a build instruction for it. The build system will use the definition
from the dna_valokuitu-plus-ex400 board and the build will fail.
This fixes the build of the ramips target.
Fixes: 665c2154ef ("ramips: add basic support for tp-link er605-v2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 746e894877)
The previous host installation fix accidentally moved the rpath settings
out of CMAKE_HOST_OPTIONS and into CMAKE_OPTIONS.
Fixes: ae42ecaad4 ("ucode: fix host installation")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 2ee1392e09)
Add the GPIO pin of the PoE passthrough switch on the Aruba AP-303H.
Power is activated when the pin is low. It enables a PSE chip, so power
is only supplied to downstream devices when they are 802.3af/at
compliant devices.
Ensure you use a sufficient power supply when chaining a consuming
device after the AP.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b40cc46cc8)
Because these capability advertisements default to on in lldpd, they
became absent at reload, and not restart, due to how the reload logic
works ( keep daemon running, send unconfigured and then the new config
via socket ), and it was not evident unless you happened to be looking
for it (e.g. via pcap or tcpdump). It was also not evident from the
manpage ( have now sent patches upstream ).
At reload time, the unconfigure logic disabled them unless they were
explicitly enabled (compare with other settings where 'unconfigure' just
resets them). Now they default to on/enabled at init time, and are
explicitly 'unconfigure'd at startup if the user disables them via:
lldp_mgmt_addr_advertisements=0
lldp_capability_advertisements=0
In other words: explicit is necessary to disable the advertisements.
The same applies to 'configure system capabilities enabled'. Technically
'unconfigure'd is the default but now it is explicit at reload.
Tested on: 23.05.3
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
(cherry picked from commit 708101c141)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
For interface type parameters, the man page documents patterns:
```
*,!eth*,!!eth1
uses all interfaces, except interfaces starting with "eth",
but including "eth1".
```
* Renamed `_ifname` to `_l2dev`.
* get the l2dev via network_get_physdev (and not l3dev)
* Glob pattern `*` is also valid - use noglob for this
The net result is that now interface 'names' including globs '*' and '!'
inversions are included in the generated lldpd configs.
Temporarily `set -o noglob` and then `set +o noglob` to disable & enable
globbing respectively, because when we pass `*` as an interface choice,
other file and pathnames get sucked in from where the init script runs,
and the `*` never makes it to lldpd.
Tested extensively on: 22.03.6, 23.05.3
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
[ squash with commit bumping release version ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 4a81d868db)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
Defaults to off.
Available from >= 0.7.15
These are sent in TLV
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
(cherry picked from commit 50021d3222)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
Defaults to off.
Only available from >= 1.0.15
These capabilities are sent in TLV.
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
(cherry picked from commit 4d8f56bd59)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
only available from >= 1.0.15
Comments are useful. Apparently this config parameter was committed when
openwrt used an older version of lldpd which did not yet support it.
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
(cherry picked from commit b476917502)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
No functionality/behaviour changes; code is synonymous
Tested on: 22.03.6
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 5364fe0f01)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
For certain lldp_class scenarios (2 & 3) a policy must be set also.
Class 4 is default, although it's good to handle the policy eventuality.
Here, set a default lldp_policy for all lldp_class scenarios. Any
lldp_policy can now be set.
Depends on PR #14584 (which introduced an `if` block)
Tested on 22.03.5, 22.03.6
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 497fafb8ae)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
Previously only partially implemented. After commit
5007f488bb lldp_location was never removed
Now, add the value of lldp_location to the generated config.
The location param has a few syntaxes, so the config acquires the first
usage from the man page: 'address country EU'
Supplementary fix for PR #14193 (this param was included in the original
PR #13018 but the lldp_location fixes were absent from PR #14193).
Tested on 22.03.5, 22.03.6
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 53252eeb3b)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
from commit 3ce909914a
The lldpd man page says that "configure lldp tx-interval" can
specify an interval value in milliseconds by appending a "ms" suffix to
the figure. Thus mandating string handling, and not integer comparison.
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 79ee4cb039)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
from commit 909f063066
Now pass two params to get_config_cid_ifaces() for:
cid_interface
interface
Each of which is a CSV of interfaces.
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 228d4e7f1b)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
from commit ac771313eb
portidsubtype takes 1 of 2 possible keywords which do not need quoting:
configure lldp portidsubtype ifname | macaddress
The third keyword 'local' is used in the syntax when individual ports
are being defined:
configure [ports ethX [,…]] lldp portidsubtype local value
When this syntax is used, quoting is useful (see test cases for lldpd).
In the init file, the 'local' syntax is unused.
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit bd1b17d589)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
from commit c98ee4dbb3
agent-type takes 1 of 3 possible keywords which do not require quoting:
configure lldp agent-type nearest-bridge | nearest-non-tpmr-bridge
| nearest-customer-bridge
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit 24a4da527f)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
from commit 3ce909914a
'capabilities enabled x' where x is a string of CSV
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
(cherry picked from commit b039641071)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
allow EDP support if compiled and add force EDP option
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit d274867c21)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
prevent SNMP options being passed unless lldpd supports them
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 8b2d02e48c)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
increment Makefile package release to reflect changes to init script
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 1b36d44323)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
add option to set LLDP transmit delay, hold timers to set update frequency
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit a5f715da71)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
add option to override system platform instead of using kernel name
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 4159acceeb)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
add option to force SONMP to be enabled even when no peer detected
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 4ac134aa78)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
add option to force FDP when no peers detected
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 1be2088a52)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
add option to specify CDPv1 or CDPv2 and separately enable or force each
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit b67182008f)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
add option to allow LLDP disabling while using other supported protocols
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
(cherry picked from commit 61dbe756d8)
Link: https://github.com/openwrt/openwrt/pull/15299
Signed-off-by: Robert Marko <robimarko@gmail.com>
