Commit Graph

23050 Commits

Author SHA1 Message Date
Adrian Schmutzler
1deaf695ec ramips: fix/tidy up 4M tplink-v2-image flash layouts
For the TP-Link 4M devices with tplink-v2-image recipe
(mktplinkfw2.c), there are two different flash layouts based
on the size of the (u)boot partition:

device         uboot    OEM firmware  OpenWrt (incl. config)
tl-wr840n-v5   0x20000  0x3c0000      0x3d0000
tl-wr841n-v14  0x10000  0x3d0000      0x3e0000

In both cases, the 0x10000 config partition is used for the firmware
partition as well due to the limited space available and since it's
recreated by the OEM firmware anyway.

However, the TFTP flashing process will only copy data up to the
size of the initial (OEM) firmware size. Therefore, while we can
use the bigger partition to have additional erase blocks on the
device, we have to limit the image sizes to the TFTP limits.

So far, only one layout definition has been set up in mktplinkfw2.c
for 4M mediatek devices. This adds a second one and assigns them
to the devices so the image sizes are correctly restrained.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 12:17:08 +02:00
Adrian Schmutzler
18b7d87a8f kirkwood: get rid of BOARD_NAME and tidy up DEVICE_DTS
Since most of the DTS file names follow a common scheme now, let's
update the automatically generated DEVICE_DTS value and get rid
of some DEVICE_DTS and all BOARD_NAME entries for individual devices.

This should specifically make the job easier for developers adding
new devices, as they are not tempted to copy over BOARD_NAME anymore.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 10:47:22 +02:00
Adrian Schmutzler
356866c481 target: replace remaining occurrences of ifconfig with ip
ifconfig is effectively deprecated for quite some time now. Let's
replace the remaining occurrences for our target setup by the
corresponding ip commands now.

Note that this does not touch ar71xx, as it will be dropped anyway,
and changing it would only make backports harder.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-03 10:42:04 +02:00
Sungbo Eo
c90db26e05 ar71xx: restore support for boot console with arbitrary baud rates
Commit 1bfbf2de6d ("ar71xx: serial: core: add support for boot console
with arbitrary baud rates") added support for arbitrary baud rates which
enabled 250000 baud rate for Yun. But the patch was not ported to kernel
4.9, and since then the kernel set its baud rate to 9600. This commit ports
the patch to kernel 4.14, thereby restoring the serial console of Yun.

Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-02 18:10:06 +02:00
Sungbo Eo
a5e404d192 ar71xx: enable ethernet LED of Arduino Yun
Commit 05d73a2a73 enabled GPIO on ethernet LED, but proper LED setup was
not added then. This commit fixes it by reverting the change on the LED.

Fixes: 05d73a2a73 ("ar71xx: Arduino Yun board 'WLAN RST' button support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-02 16:34:21 +02:00
Sungbo Eo
58dc1d0637 ar71xx: fix sysupgrade for Arduino Yun
Commit bb46b635df changed its partition scheme, but sysupgrade image
validation still uses the old format. This commit fixes it so that
force flag is not needed for sysupgrade.

Fixes: bb46b635df ("ar71xx: move Arduino Yun to generic building code")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-02 16:34:21 +02:00
Sungbo Eo
43896dc0b0 Revert "ar71xx: fix Arduino Yun enabling of level shifters outputs"
This reverts commit 077253dd66.

The output enable pins should be disabled by default, and only enabled when
used. Otherwise unwanted conflicts might occur between MCU and SoC pins.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2020-08-02 16:34:21 +02:00
Adrian Schmutzler
8a8ef4ed86 ath79/mikrotik: create shared device definitions for nor and nand
Move the image preparation and nand-utils package selection into
common device definitions for NOR/NAND devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-08-01 18:31:24 +02:00
Stijn Tintel
5c3e83fa88 kernel: fix missing TRANSPARENT_HUGEPAGE symbols
Enabling KERNEL_TRANSPARENT_HUGEPAGE exposes 2 missing symbols:
* CONFIG_READ_ONLY_THP_FOR_FS
* TRANSPARENT_HUGEPAGE_ALWAYS
* TRANSPARENT_HUGEPAGE_MADVISE

The first one was added in 5.4, and is marked experimental there so just
disable it in the generic config.

For the latter two, we should not force the user to use either of them,
so add them as build-configurable kernel options.

Fixes: d1a8217d87 ("kernel: clean-up build-configurable kernel config symbols")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2020-08-01 14:33:46 +01:00
Stijn Tintel
1bff9f5b78 kernel: add missing config symbol
This symbol is exposed on ARM64 with EFI enabled in the kernel config.
Currently this happens only on ipq807x, but as there might be new ARM64
targets with EFI in the future it is better to add the symbol to the
generic config.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Jo-Philipp Wich <jo@mein.io>
2020-08-01 15:19:11 +03:00
Linus Walleij
9e02580d52 gemini: Add swap partition to DNS-313
Sometimes when using the DNS-313 memory usage can peak and
with a simple swap partition we can avoid running into the
roof and invoking the OOM killer. Set this partition to
128MB (twice the size of the memory of the DNS-313).

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2020-07-31 18:34:40 +02:00
Christian Lamparter
caa6ada969 apm821xx: disable WNDR4700 5.4 image
The compressed image that the buildbots are building is too large for
the netgear uboot and it crashes and soft-bricks the device.

| Uncompressing Kernel Image ...
| LZMA: uncompress or overwrite error 1 - must RESET board to recover

The whole target likely needs to be switched zImage which is a major
hassle due to powerpc's legacy bootwrapper setup as compared to ARM.
So for now, disable the device.

Reported-by: Wiktor Stasiak (FS#3258)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-07-31 18:17:34 +02:00
Adrian Schmutzler
65305cb448 kirkwood: use real model names for Linksys devices
This replaces the internal device names "Audi" and "Viper" with the
real model names, which a user would look for. This makes the
Linksys devices on this target consistent with the names recently
changed for mvebu based on the same idea.

As a consequence, the "viper" device definition is split into two
separate definitions with the correct names for both real models.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 15:03:43 +02:00
Tony Ambardar
a4856dab0d kernel: mips: restore missing MIPS32 cBPF JIT
Kernel v5.1 included an eBPF JIT for MIPS32 kernels, but problems were
discovered [1] and the changes later reverted in kernel v5.5 with commits:

  * f8fffebdea75 ("MIPS: BPF: Disable MIPS32 eBPF JIT")
  * 36366e367ee9 ("MIPS: BPF: Restore MIPS32 cBPF JIT")

Only the first of these was backported to LTS kernel 5.4, leaving cBPF
programs without a JIT and introducing a performance regression for any
such users e.g. libpcap, tcpdump, etc.

Restore cBPF performance by backporting the second commit above:
  * 070-v5.5-MIPS-BPF-Restore-MIPS32-cBPF-JIT.patch

[1] https://lore.kernel.org/bpf/20191205182318.2761605-1-paulburton@kernel.org/

Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
2020-07-31 13:42:14 +01:00
Adrian Schmutzler
664237deaa mvebu: fix alphabetic sorting in 02_network
This has been overlooked when removing solidrun,clearfog-a1 entry.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Adrian Schmutzler
e496eefccc mvebu: increase compat version for SolidRun ClearFog Base
When changing the Pro variant to DSA, the ethernet interface rename
script was dropped by all devices to keep them in sync:

  be309bfd74 ("mvebu: drop 06_set_iface_mac preinit script")

Therefore, network config will be broken after upgrade for the
Base variant as well. Increase the compat version and provide a
message to signal that to the users.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Adrian Schmutzler
090779b24e kirkwood: implement compatibility version for DSA migration
This implements the newly introduced compat-version to prevent
upgrade between swconfig and DSA for kirkwood.

Just define a compat version with minor increment and an appropriate
message for both image (in Makefile) and device (in base-files).

Since we never removed SUPPORTED_DEVICES for this target, we don't
have to add it back either.

Attention:

All users that already updated to the DSA versions in master will
receive the same incompatibility warning since their devices are still
"1.0" as far as fwtool can tell.
Those, and only those, can bypass the upgrade check by using force (-F)
without having to reset config again. In addition, the new version
string needs to be put into uci config manually, so the new fwtool
knows that it actually deals with a "1.1":

   uci set "system.@system[-1].compat_version=1.1"
   uci commit system

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Adrian Schmutzler
494f12c52d mvebu: implement compatibility version for DSA migration
This implements the newly introduced compat-version to prevent
upgrade between swconfig and DSA for mvebu.

Just define a compat version with minor increment and an appropriate
message for both image (in Makefile) and device (in base-files).

Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES
that have been removed in previous patches to prevent broken config.

Attention:

All users that already updated to the DSA versions in master will
receive the same incompatibility warning since their devices are still
"1.0" as far as fwtool can tell.
Those, and only those, can bypass the upgrade check by using force (-F)
without having to reset config again. In addition, the new version
string needs to be put into uci config manually, so the new fwtool
knows that it actually deals with a "1.1":

   uci set "system.@system[-1].compat_version=1.1"
   uci commit system

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
Robinson Wu
84cb0f7ace ramips: add support for JS76x8 series DEV boards
This commit adds support for the Jotale JS76x8 series development boards.
These devices have the following specifications:

- SOC: MT7628AN/NN, MT7688AN, MT7628DAN
- RAM of MT7628AN/NN and MT7688AN: 64/128/256 MB (DDR2)
- RAM of MT7628DAN: 64 MB (DDR2)
- FLASH:8/16/32 MB (SPI NOR)
- Ethernet:3x 10/100 Mbps ethernet ports (MT76x8 built-in switch)
- WIFI:1x 2T2R 2.4 GHz Wi-Fi
- LEDs:1x system status green LED, 1x wifi green LED,
       3x ethernet green LED
- Buttons:1x reset button
- 1x microSD slot
- 4x USB 2.0 port
- 1x mini-usb debug UART
- 1x DC jack for main power (DC 5V)
- 1x TTL/RS232 UART
- 1x TTL/RS485 UART
- 13x GPIO header
- 1x audio codec(wm8960)

Installation via OpenWrt:

The original firmware is OpenWrt, so both LuCI and sysupgrade can be used.

Installation via U-boot web:

1. Power on board with reset button pressed, release it
   after wifi led start blinking.
2. Setup static IP 192.168.1.123/4 on your PC.
3. Go to 192.168.1.8 in browser and upload "sysupgrade" image.

Installation via U-boot tftp:
1. Connect to serial console at the mini usb, which has been connected to UART0
   on board (115200 8N1)
2. Setup static IP 192.168.1.123/4 on your PC.
3. Place openwrt-firmware.bin on your PC tftp server (192.168.1.123).
3. Connect one of LAN ports on board to your PC.
4. Start terminal software (e.g. screen /dev/ttyUSB0 115200) on PC.
5. Apply power to board.
6. Interrupt U-boot with keypress of "2".
7. At u-boot prompts:
   Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
   Input device IP (192.168.1.8) ==:192.168.1.8
   Input server IP (192.168.1.123) ==:192.168.1.123
   Input Linux Kernel filename (root_uImage) ==:openwrt-firmware.bin
8. board will download file from tftp server, write it to flash and reboot.

Signed-off-by: Robinson Wu <wurobinson@qq.com>
[add license to DTS files, fix state_default and reduce to the mimimum,
move phy0tpt trigger to DTS, drop ucidef_set_led_timer, fix network ports]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-31 11:40:15 +02:00
David Bauer
ced167d729 ramips: limit 5GHz channels for RAVPower RP-WD009
When selecting a channel below 100 on the 5GHz radio, the channel will
be detected as busy all the time.

Survey data from wlan1
	frequency:			5240 MHz [in use]
	channel active time:		165729 ms
	channel busy time:		158704 ms
	channel transmit time:		0 ms

Channels 100 and above work fine:

Survey data from wlan1
	frequency:			5500 MHz
	channel active time:		133000 ms
	channel busy time:		21090 ms
	channel transmit time:		0 ms

Limit the available channels, so users do not have the impression
their device is broken.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-30 22:33:53 +02:00
Petr Štetiar
e9f7923a1d treewide: mark devices as BROKEN instead of commenting out
This adds the newly introduced BROKEN flag to a bunch of devices
that previously just had TARGET_DEVICES commented out. By this, we
can select them in make menuconfig when BROKEN developer config option
is selected, instead of having to edit the code.

In contrast to DEFAULT := n, this is meant to cover devices that
don't boot or don't compile at all.

ath25: np25g, wpe53g
  both disabled during kernel bump 3.18->4.4 without reason given
  f89a20a89a ("ath25: update kernel from 3.18 to 4.4")

bcm53xx: linksys-ea6300-v1, linksys-ea9200, linksys-ea9500
  broken due to insufficient/broken TRX support
  55ff15cfd5 ("bcm53xx: disable building Linksys EA6300 V1 image")
  cd0f9900a4 ("bcm53xx: parepare for building more Linksys images")

bcm63xx: tplink-archer-c5-v2, tplink-archer-c9-v1
  disabled when kernel 5.4 support was added, probably broken
  50c6938b95 ("bcm53xx: add v5.4 support")

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[limit to subset of devices, use BROKEN, adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-30 21:49:22 +02:00
Petr Štetiar
504000d520 treewide: use DEFAULT := n to disable non-broken devices
This uses DEFAULT := n on a bunch of devices that previously were
"disabled" by commenting out TARGET_DEVICES. This will allow to
build them without having to modify the code, but they will not
be selected for default build or buildbots.

The change is applied to all devices that are not "broken", but suffer
from image site limitations or similar, or have been added in the past
but never confirmed to run on the device properly:

at91: at91-q5xr5:
  kernel image too big
  31aeae0774 ("at91: do not build image for at91-q5xr5")

bcm47xx: asus-rt-ac66u:
  disabled since it was added in 2015
  69aefc771f ("brcm47xx: build images for Asus devices")

bcm47xx: netgear-wndr3400-vcna, netgear-wnr3500u, netgear-wnr3500-v2-vc
  added disabled in 2012, but never confirmed to work on devices
  5dec9dd3b2 ("brcm47xx: add code to generate images for some netgear
    devices")

bcm53xx: netgear-r8500
  added disabled: "start working on Netgear R8500"
  3b76c7cf0b ("bcm53xx: start working on Netgear R8500")

Signed-off-by: Petr Štetiar <ynezz@true.cz>
[limit to subset of devices, adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-30 21:48:38 +02:00
Adrian Schmutzler
bf5c56ba57 ath79: cosmetic fixes for partition node of D-Link DIR-825 B1
Make the node name match the reg property and remove the unused
DT label.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-30 21:43:56 +02:00
Daniel Golle
d1a8217d87 kernel: clean-up build-configurable kernel config symbols
Don't explicitely disable options in target/linux/generic/config-* if
they are already controlled in config/Config-kernel.in.
Add a bunch of new symbols  and prepare defaults for using only unified
hierarchy (ie. cgroup2). Update symbol dependencies while at it

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-07-30 16:59:47 +01:00
Luochongjun
68ac3f2cdd ath79: add support for gl-e750
The gl-e750 is a portable travel router that gives you safe access to
the internet while traveling.

Specifications:
- SoC: Qualcomm Atheros AR9531 (650MHz)
- RAM: 128 MB DDR2
- Flash: 16 MB SPI NOR (W25Q128FVSG) + 128 MB SPI NAND (GD5F1GQ4UFYIG)
- Ethernet: 10/100: 1xLAN
- Wireless: QCA9531 2.4GHz (bgn) + QCA9887 5GHz (ac)
- USB: 1x USB 2.0 port
- Switch: 1x switch
- Button: 1x reset button
- OLED Screen: 128*64 px

MAC addresses based on vendor firmware:
LAN *:a0 art 0x0
2.4GHz *:a1 art 0x1002
5GHz *:a2 art calculated from art 0x0 + 2

Flash firmware:
Since openwrt's kernel already exceeds 2MB, upgrading from the official
version of GL-inet (v3.100) using the sysupgrade command will break the
kernel image. Users who are using version 3.100 can only upgrade via
uboot. The official guidance for GL-inet is as follows:
https://docs.gl-inet.com/en/3/troubleshooting/debrick/

In the future, GL-inet will modify the firmware to support the sysupgrade
command, so users will be able to upgrade directly with the sysupgrade
command in future releases.

OLED screen control:
OLED controller is connected to QCA9531 through serial port, and can send
instructions to OLED controller directly through serial port.
Refer to the links below for a list of supported instructions:
https://github.com/gl-inet/GL-E750-MCU-instruction

Signed-off-by: Luochongjun <luochongjun@gl-inet.com>
[fix alphabetic sorting in 10-fix-wifi-mac, drop check-kernel-size]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-29 20:49:48 +02:00
Adrian Schmutzler
6da5356195 lantiq: disable default build for devices with 4M flash
It has been decided that the 19.07 release will be last one to include
4/32 devices.

This disables default build for all devices with 4M flash on lantiq.
Note that this will affect _all_ devices for amazonse ("ase") and
xway_legacy subtarget.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-29 12:08:16 +02:00
Adrian Schmutzler
55e2d5eb3b ath79: disable default build for devices with 4M flash
It has been decided that the 19.07 release will be last one to include
4/32 devices.

This disables default build for the remaining devices with 4M flash
on ath79. Note that this will leave exactly one enabled device for
ath79/tiny subtarget, PQI Air-Pen, which was moved there due to
kernel size restrictions.

All 4M TP-Link devices have already been disabled in
8819faff47 ("ath79: do not build TP-Link tiny images by default")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-29 12:08:16 +02:00
Adrian Schmutzler
01a3e891d7 ath79: reorganize common image definitions for Netgear
Netgear currently has a special definition for tiny devices, which
is only used by two devices. Despite, it sets ups the IMAGE/default
definition individually for all devices, although there is actually
only one exception.

This merges the common parts into a single netgear_generic definition
(in contrast to netgear_ath79_nand), and adjusts the individual
definitions accordingly.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-29 12:08:16 +02:00
David Bauer
c5360894dc rockchip: enable rockchip-thermal
Enable the rockchip-thermal driver to allow reading the temperature of
the SoC.

Tested on NanoPi R2S

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-29 01:40:20 +02:00
David Bauer
7a4fc8906c rockchip: distribute net interrupts
This adds a hotplug script for distributing interrupts of eth0 and eth1
across different cores. Otherwise the forwarding performance between
eth0 and eth1 is severely affected.

The existing SMP distribution mechanic in OpenWrt can't be used here, as
the actual device IRQ has to be moved to dedicated cores. In case of
eth1, this is in fact the USB3 controller.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
David Bauer
5a57a1ac1f arm64: dts: rockchip: Add txpbl node for RK3399/RK3328
Some rockchip SoCs like the RK3399 and RK3328 exhibit an issue
where tx checksumming does not work with packets larger than 1498.

The default Programmable Buffer Length for TX in these GMAC's is
not suitable for MTUs higher than 1498. The workaround is to disable
TX offloading with 'ethtool -K eth0 tx off rx off' causing performance
impacts as it disables hardware checksumming.

This patch sets snps,txpbl to 0x4 which is a safe number tested ok for
the most popular MTU value of 1500.

For reference, see https://lkml.org/lkml/2019/4/1/1382.

Signed-off-by: Carlos de Paula <me@carlosedp.com>
Link: https://lore.kernel.org/r/20200218221040.10955-1-me@carlosedp.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
David Bauer
6242ac4735 rockchip: enable LAN LED configuration
This enables the LEDs on the LAN interfaces.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
David Bauer
b7a9a183fb rockchip: add NanoPi R2S support
Hardware
--------
RockChip RK3328 ARM64 (4 cores)
1GB DDR4 RAM
2x 1000 Base-T
3 LEDs (LAN / WAN / SYS)
1 Button (Reset)
Micro-SD slot
USB 2.0 Port

Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.

MAC-address
-----------
The vendor code supports reading a MAC address from an EEPROM connected
via i2c0 of the SoC. The EEPROM (address 0x51) should contain the MAC
address in binary at offset 0xfa. However, my two units didn't come with
such an EEPROM soldered on. The EEPROM should be placed between the SoC
and the GPIO pins on the board. (U10)

Generating rendom MAC addresses works around this issue. Otherwise, all
boards running the same image have identical MAC addresses.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
David Bauer
b72f7c64a4 rockchip: allow for multiple boot-scripts
Add support for select a bootscript depending on the device built. This
is necessary, as the FriendlyARM NanoPi R2S needs a different bootcmd in
order to produce output on the debug UART.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-07-28 15:52:44 +02:00
Adrian Schmutzler
bcd7a0c095 arc770: update kernel version to 5.4
Update config with make kernel_oldconfig and copy/refresh patch.

Add CONFIG_WATCHDOG_CORE=y to fix the following error as done for
several targets already:

 Package kmod-hwmon-sch5627 is missing dependencies for the following
 libraries:
 watchdog.ko

Directly switch to kernel 5.4.

This patch is compile-tested only. However, the target is essentially
pure upstream with a single patch, and it has been reported that
kernel 5.4 has been run on this target successfully already.

Note that in my local tests building with all packages/kmods failed
since openvswitch selects libunwind, which doesn't build for arc with
the following error:

checking if we should build libunwind-ptrace... yes
checking if we should build libunwind-setjmp... yes
checking for build architecture... x86_64
checking for host architecture... arc
checking for target architecture... arc
checking for target operating system... linux-gnu
checking for ELF helper width... configure: error: Unknown ELF target: arc
make[3]: *** [Makefile:65: /data/openwrt/build_dir/target-arc_arc700_uClibc/
   libunwind-1.3.1/.configured_68b329da9893e34099c7d8ad5cb9c940] Error 1

Deselecting all kmod-openvswitch* packages will have the build run through.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 20:15:10 +02:00
Adrian Schmutzler
88689da65f lantiq: fix cosmetic issues with partition offsets and sizes
This fixes a few cosmetic issues with partition offset and size
that are inconsistent probably due to copy/pasting.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 13:02:47 +02:00
Josh Bendavid
11bff24b3e ramips: add support for D-Link DIR-1960 A1
This patch adds support for D-Link DIR-1960 A1. Given the similarity with
the DIR-1760/2660 A1, this patch also introduces a common DTSI which can
be shared with these devices, with support to be added in future commits.

Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
        WiFi 5G (white), USB 3.0 (white)

Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips

Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
  button, then re-plug it. Keep the reset button pressed until the power
  LED starts flashing orange, manually assign a static IP address under
  the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1

* Some modern browsers may have problems flashing via the Recovery GUI,
  if that occurs consider uploading the firmware through cURL:

    curl -v -i -F "firmware=@file.bin" 192.168.0.1

MAC addresses:

lan   factory 0xe000     *:EB (label)
wan   factory 0xe006     *:EE
2.4   factory 0xe000 +1  *:EC
5.0   factory 0xe000 +2  *:ED

Seems like vendor didn't replace the dummy entrys in the calibration data.

Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
[fix whitespace issues, create patch to merge DIR-1960 first, move
special WiFi MAC settings to DTS, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 12:37:07 +02:00
Adrian Schmutzler
8126e572dd imx6: use device-tree compatible for board name
In imx6, we currently use the model from DTS to derive a board name
manually in /lib/imx6.sh.

However, if we have individual DTS files anyway, we can exploit
generic 02_sysinfo and use the compatible as board name directly.

While at it, remove the wildcards from /lib/upgrade/platform.sh as
these might make code shorter, but are quite unpleasant when grepping
for a specific device.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 12:10:45 +02:00
Adrian Schmutzler
0f3c3a5fb2 layerscape: harmonize device strings
OpenWrt lately has harmonized device (definition) names to the
pattern vendor_model to improve overall consistency, also with
other values like the DTS compatible.

This patch applies that scheme to the layerscape target.

Since this (intentionally) creates a bigger overlap between DTS names,
compatible, and device definition name, it also moves DEVICE_DTS and
SUPPORTED_DEVICES definitions to the Device/Default blocks.

Apart from that, it also modifies several packages to use consistent
naming in order to keep the $(1) file references working.

While at it, remove one layer of complexity for the setup in
tfa-layerscape package.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 12:06:52 +02:00
Adrian Schmutzler
a1eb2c4633 mvebu: only disable WRT1900AC v1 and WRT32X for buildbots
Use "DEFAULT := n" to only disable devices for buildbots, but
keep them available for manual build.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-07-27 11:05:25 +02:00
Jo-Philipp Wich
ac9730c495 mvebu: disable WRT1900AC v1 and WRT32X images for now
The kernel appears to have grown too large, breaking the build for the
entire target.

Disable the affected images for now until the situation is dealt with.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2020-07-26 18:58:22 +02:00
David Woodhouse
b36422b914 mediatek: mt7623: add full system image for UniElec U7623
This adds a full eMMC image including U-Boot, which means that the
kernel can inherit the true RAM size detected by the preloader.

As implemented in previous commits, sysupgrade to this image from
the legacy layout (and via that, from the vendor-installed image)
is supported.

Rename the legacy image for the 512MiB board, for clarity.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 17:08:31 +08:00
David Woodhouse
1113dcab05 mediatek: mt7623: rename gen_banana_pi_img.sh → gen_mtk_mmc_img.sh
As I buy more hardware and continue to work on consolidation, This will
apply to a lot of MediaTek platforms; rename it accordingly.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 17:08:21 +08:00
David Woodhouse
f5cebbe2e4 mediatek: mt7623: make gen_banana_pi_img.sh more generic
This actually covers fairly much all the MediaTek platforms; they
only have different images because they don't include the preloader
and U-Boot, and rely on preinstalled stuff from the vendor.

So this script can slowly take over the world as we complete the
support for various other platforms, starting with UniElec U7623…

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 17:08:21 +08:00
David Woodhouse
5787684cb4 mediatek: mt7623: add scatter file for unbricking with SP Flash Tool
Many MediaTek SoCs can be unbricked by using the SP Flash Tool from
http://spflashtool.com/ along with a "scatter list" file, which is
just a text file listing which image gets loaded where.

We use a trivial partition layout for the tool, with the whole eMMC
image as a single "partition", which means users just need to unzip
the sysupgrade image. Doing the real partition layout would be overly
complex and would require the individual partitions to be shipped
as artifacts — or users to extract them out of the sysupgrade image
just for the tool to put them adjacent to each other on the eMMC
anyway.

The tool does require a copy of the preloader in order to operate,
even when it isn't flashing the preloader to the eMMC boot region.
So drop that into the bin directory as an artifact too.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 17:07:52 +08:00
Chuanhong Guo
65fc47cac5 mediatek: mt7623: build lzma fit for bpi-r2
bpi-r2 images are shipped with mainline u-boot which can extract lzma
with no problem.
remove custom kernel recipe to build lzma fit image instead of
uncompressed fit with zboot.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-07-26 17:04:49 +08:00
David Woodhouse
29fa5526a2 mediatek: mt7623: prepare for full sysupgrade support on UniElec U7623
An upcoming commit will add a full system image for U7623 which will
contain the MBR partition table and U-Boot too.

That contrasts with the current image which only owns the eMMC from
sector 0xa00 onwards, and must start with a legacy uImage.

Prepare for sysupgrade to the new images, and cope with the fact that
the recovery partition will be /dev/mmcblk0p2 instead of /dev/mmcblk0p1
after the upgrade.

This commit could potentially be backported to 19.07 to allow for direct
sysupgrade to the new image layout.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:36 +08:00
David Woodhouse
7a1eaa446b mediatek: mt7623: increase flexibility of finding recovery partition
I'm about to change the layout of the images for UniElec U7623 so make it
find the recovery partition based on which the root partition is too.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:36 +08:00
David Woodhouse
ff8cc137fb mediatek: mt7623: fix Ethernet setup for TRGMII mode
This fixes the TX performance issues seen on MT7623 boards.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:36 +08:00
David Woodhouse
be3c8f8b2b mediatek: fix Ethernet support on UniElec U7623
The definition of the switch in the device-tree was not correct. Make it
look more like the Banana Pi R2, which works.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-07-26 16:42:35 +08:00