Specifications:
SOC: Atheros/Qualcomm QCA9557-AT4A @ 720MHz
RAM: 2x Winbond W9751G6KB-25 (128 MiB)
FLASH: Hynix H27U1G8F2BTR-BC TSOP48 ONFI NAND (128 MiB)
WIFI1: Atheros AR9550 5.0GHz (SoC)
WIFI2: Atheros AR9582-AR1A 2.4GHz
WIFI2: Atheros AR9582-AR1A 2.4GHz + 5GHz
PHYETH: Atheros AR8035-A, 802.3af PoE capable Atheros (1x Gigabit LAN)
LED: 1x Power-LED, 1 x RGB Tricolor-LED
INPUT: One Reset Button
UART: JP1 on PCB (Labeled UART), 3.3v-Level, 115200n8
(VCC, RX, TX, GND - VCC is closest to the boot set jumper
under the console pins.)
Flashing instructions:
Depending on the installed firmware, there are vastly different
methods to flash a MR18. These have been documented on:
<https://openwrt.org/toh/meraki/mr18>
Tip:
Use an initramfs from a previous release and then use sysupgrade
to get to the later releases. This is because the initramfs can
no longer be built by the build-bots due to its size (>8 MiB).
Note on that:
Upgrades from AR71XX releases are possible, but they will
require the force sysupgrade option ( -F ).
Please backup your MR18's configuration before starting the
update. The reason here is that a lot of development happend
since AR71XX got removed, so I do advise to use the ( -n )
option for sysupgrade as well. This will cause the device
to drop the old AR71xx configuration and make a new
configurations from scratch.
Note on LEDs:
The LEDs has changed since AR71XX. The white LED is now used during
the boot and when upgrading instead of the green tricolor LED. The
technical reason is that currently the RGB-LED is brought up later
by a userspace daemon.
(added warning note about odm-caldata partition. remove initramfs -
it's too big to be built by the bots. MerakiNAND -> meraki-header.
sort nu801's targets)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This sort of reverts Koen Vandeputte's commit
6561ca1fa5 ("ath79: ar934x: fix mounting issues if subpage is not supported")
since it does not work on the MR18 as the UBI is coming from
Meraki in that way and it used to work with AR71XX before.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Two Mikrotik board families (SXT 5nD R2 and Routerboard 92x are using
software ECC on NAND. Some of them use chips capable of subpage write,
others do not - within the same family, and a common block size is
required for UBI, to avoid mounting errors. Set the ECC step size
explicitly for them to 2048B, so UBI can mount existing volumes without
problems, at the same time allowing to unlocking subpage write functionality,
reuqired for Meraki MR18.
Fixes: 6561ca1fa5 ("ath79: ar934x: fix mounting issues if subpage is not supported")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
specify that this functions adds a Cisco Meraki
special-sauce header for their custom loader/uboot.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
some targets do not define the _REDIR_TIME64 macro resulting in a
build error regression since ddfe5678a4
fix by checking if the macro is defined
[1] https://github.com/openwrt/openwrt/issues/12587Fixes: #12587
Fixes: ddfe5678a4 ("fortify-headers: fix inconsistent time_t version of ppoll")
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
d4f56f0e6971 add support for handling traffic to/from the bridge device
3ea579064c00 nl: add separate socket for netlink commands
4ec5a51c6d01 nl: fetch packet stats for offloaded flows
0319fd080bf5 add support for configuring a fixed output port for a bridge member port
5b730f0c2cf5 bridger-bpf: fix build on older kernels
00af6c6e8350 nl: process IFLA_MASTER in any nl events, but skip wireless events
a2794f95756e bridger-bpf: add bpf_skb_pull_data call
6974093eb036 nl: rework vlan code to use the iflink API
d0f79a16c749 nl: do not attempt to enable flow offload on older kernels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Allowing the (kernel) packet priority to be set through UCI.
This makes it straightforward to set some VLAN priority for DHCP
requests through a simple egress qos map. (Avoiding the need for
firewall matching and marking through iptables, which prevents using
flow offloading).
(Such priority tag is a hard requirement for some ISPs, such as Orange
in France).
Depends on: https://github.com/openwrt/odhcp6c/pull/74
Signed-off-by: Pacien TRAN-GIRARD <pacien.trangirard@pacien.net>
We only use 5.15 kernel. So remove all those unnecessary symbols
referencing 5.10 or 5.15 kernel.
Can be found with:
git grep -E 'LINUX_5_1(0|5)'
Note that we remove the dependency from "sound-soc-chipdip-dac" instead
of removing the complete kernel package. The 5.15 version bump forgot to
delete the "@LINUX_5_10" dependency. The kernel package is still needed
in 5.15 kernel.
Signed-off-by: Nick Hainke <vincent@systemli.org>
We removed 5.10 kernel, so remove also the patch that only affects 5.10
kernels.
Manually refresh:
- 0005-SSDK-config-add-kernel-5.15.patch
- 0010-QSDK-config-Avoid-Werror-heroics.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
The purpose of this is to remove all of the compatibility code that is
normally compiled into glibc for kernels < 5.15 from our build. Only
Linux kernels >= 5.15 will be supported.
Signed-off-by: Nick Hainke <vincent@systemli.org>
All targets are bumped to 5.15. Remove the old 5.10 patches, configs
and files using:
find target/linux -iname '*-5.10' -exec rm -r {} \;
Further, remove the 5.10 include.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Switch to kernel 5.15 although it is marked as source only. It is marked
as source only because nobody was able to test this device.
Merging this is important to finally branch a new release. We want to
get rid completely of 5.10 kernel. Without this commit we get following
error: "Missing kernel version/hash file for 5.10." Hopfully someone
will fix the board in the rc phase or it will be removed completly.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Manually refreshed:
- 140-redboot_boardconfig.patch
- 141-redboot_partition_scan.patch
- 142-redboot_various_erase_size_fix.patch
Automatically refreshed:
- 107-ar5312_gpio.patch
- 108-ar2315_gpio.patch
- 110-ar2313_ethernet.patch
- 120-spiflash.patch
- 130-watchdog.patch
- 330-board_leds.patch
Use "make kernel_oldconfig" to refresh the new kernel config.
The Ubiquiti Nanostation 2 (XS2) and Ubiquiti Nanostation 5 (XS5) should
be marked as broken when switching to 5.15 by default. The new kernel
does not fit anymore into the partition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Switch to kernel 5.15 although it is marked as source only. It is marked
as source only because the eth0 interface can't be added to the br-lan
default interface resulting in a broken ethernet [0]. There is a
workaround to set a higher pvd (e.g. to 4000) in the dts [1].
Other functionality was already tested on a Beaglebone Black for
+6month now without issues.
Merging this is important to finally branch a new release. We want to
get rid completely of 5.10 kernel. Without this commit we get following
error: "Missing kernel version/hash file for 5.10." Hopfully someone
will fix the board in the rc phase.
- [0] https://github.com/openwrt/openwrt/issues/11953
- [1] https://github.com/openwrt/openwrt/issues/11953#issuecomment-1419078990
Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
[rewrite commit message]
Signed-off-by: Nick Hainke <vincent@systemli.org>
pcibios_map_irq request a const pci_dev while pci_find_capability
doesn't. Cast dropping the const to fix compilation warning.
Fix compilation warning:
arch/mips/pci/fixup-lantiq.c: In function 'pcibios_map_irq':
arch/mips/pci/fixup-lantiq.c:34:33: error: passing argument 1 of 'pci_find_capability' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
34 | if (pci_find_capability(dev, PCI_CAP_ID_EXP))
| ^~~
In file included from arch/mips/pci/fixup-lantiq.c:9:
./include/linux/pci.h:1129:40: note: expected 'struct pci_dev *' but argument is of type 'const struct pci_dev *'
1129 | u8 pci_find_capability(struct pci_dev *dev, int cap);
| ~~~~~~~~~~~~~~~~^~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patch does not have a valid patch headers and does not apply on
an external git tree with 'git am'. To fix this add the missing header.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The OF LED configuration patch fails on MT7621, as the necessary headers
were only included for the mediatek subtarget with an additional patch.
Fixes: 242fe8634e ("generic: add hack for MT753x LED configuration")
Signed-off-by: David Bauer <mail@david-bauer.net>
Fix compilation warning from ret not handled from copy_from_user and
missing fallthrough.
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_bbd.c: In function 'vmmc_BBD_WhiteListedCmdWr':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_bbd.c:1012:16: error: this statement may fall through [-Werror=implicit-fallthrough=]
1012 | if (IFX_TRUE == pCh->pParent->bSlicSupportsIdleMode)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_bbd.c:1028:7: note: here
1028 | case VMMC_WL_SDD_RING_CFG:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_ioctl.c: In function 'VMMC_Dev_Spec_Ioctl':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_ioctl.c:111:15: error: ignoring return value of 'copy_from_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
111 | copy_from_user (p_arg, (IFX_uint8_t*)ioarg, sizeof(arg));\
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_ioctl.c:475:7: note: in expansion of macro 'ON_IOCTL'
475 | ON_IOCTL((VMMC_CHANNEL *) pLLDummyCh,
| ^~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_ioctl.c:113:15: error: ignoring return value of 'copy_to_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
113 | copy_to_user ((IFX_uint8_t*)ioarg, p_arg, sizeof(arg));\
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_vmmc-1.9.0/src/drv_vmmc_ioctl.c:475:7: note: in expansion of macro 'ON_IOCTL'
475 | ON_IOCTL((VMMC_CHANNEL *) pLLDummyCh,
| ^~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning for switch fallthrough and
copy_to_user ret not handled.
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_dial.c: In function 'ifx_tapi_dial_OnTimer':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_dial.c:318:38: error: this statement may fall through [-Werror=implicit-fallthrough=]
318 | pTapiDialData->nHookChanges = 0;
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_dial.c:322:7: note: here
322 | case TAPI_HOOK_STATE_DIAL_L_VAL:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_event.c: In function 'IFX_TAPI_Event_Dispatch_ProcessCtx':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_event.c:1546:30: error: this statement may fall through [-Werror=implicit-fallthrough=]
1546 | pEvent->ch = IFX_TAPI_DEVICE_CH_NUMBER;
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_event.c:1548:16: note: here
1548 | case IFX_TAPI_ERRSRC_LL_CH:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c: In function 'TAPI_IoctlDev':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c:705:19: error: ignoring return value of 'copy_to_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
705 | copy_to_user ((IFX_void_t*)ioarg, p_tmp, sizeof(IFX_TAPI_CAP_t));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c: In function 'TAPI_IoctlCh':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c:1553:14: error: this statement may fall through [-Werror=implicit-fallthrough=]
1553 | ret = TAPI_statusNotSupported;
| ~~~~^~~~~~~~~~~~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_ioctl.c:1555:7: note: here
1555 | default:
| ^~~~~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'cid_fsm_alert_exec':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2037:31: error: this statement may fall through [-Werror=implicit-fallthrough=]
2037 | pTxData->nCidSubState++;
| ~~~~~~~~~~~~~~~~~~~~~^~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2039:7: note: here
2039 | case 1:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2053:31: error: this statement may fall through [-Werror=implicit-fallthrough=]
2053 | pTxData->nCidSubState++;
| ~~~~~~~~~~~~~~~~~~~~~^~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2055:7: note: here
2055 | case 2:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2070:31: error: this statement may fall through [-Werror=implicit-fallthrough=]
2070 | pTxData->nCidSubState++;
| ~~~~~~~~~~~~~~~~~~~~~^~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:2072:7: note: here
2072 | default:
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'cid_prepare_data':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1501:13: error: this statement may fall through [-Werror=implicit-fallthrough=]
1501 | if (IFX_TAPI_CID_HM_ONHOOK == pTxData->txHookMode)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1509:7: note: here
1509 | default:
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1531:16: error: this statement may fall through [-Werror=implicit-fallthrough=]
1531 | if (IFX_TAPI_CID_STD_KPN_DTMF_FSK != pConfData->nStandard)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1535:10: note: here
1535 | case IFX_TAPI_CID_GEN_TYPE_FSK:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'cid_lookup_transparent':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1425:10: error: this statement may fall through [-Werror=implicit-fallthrough=]
1425 | cidfsk_set_tx_time (pTxData, &pConfData->TapiCidFskConf);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:1427:7: note: here
1427 | case IFX_TAPI_CID_GEN_TYPE_DTMF:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'TAPI_Phone_CID_Stop_Tx':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:3445:10: error: this statement may fall through [-Werror=implicit-fallthrough=]
3445 | switch (pTxData->nAlertType)
| ^~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:3461:7: note: here
3461 | case TAPI_CID_STATE_ACK:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:3463:13: error: this statement may fall through [-Werror=implicit-fallthrough=]
3463 | if (ptr_chk(pDrvCtx->SIG.DTMFD_Override, ""))
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:3472:7: note: here
3472 | case TAPI_CID_STATE_SENDING:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c: In function 'TAPI_Phone_Get_CidRxData':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:4060:10: error: this statement may fall through [-Werror=implicit-fallthrough=]
4060 | if (IFX_Fifo_isEmpty(&(pCidRx->TapiCidRxFifo)))
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/drv_tapi-3.13.0/src/drv_tapi_cid.c:4069:4: note: here
4069 | default:
| ^~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning caused by copy_from_user ret not handled.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-atm-ase/ltq-atm/ltq_atm.c: In function 'ppe_ioctl':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-atm-ase/ltq-atm/ltq_atm.c:341:17: error: ignoring return value of 'copy_from_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
341 | copy_from_user(&mib_vcc, arg, sizeof(mib_vcc));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning from missing fallthrough
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/common/drv_dsl_cpe_api.c: In function 'DSL_DRV_AutobootControlSet':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/common/drv_dsl_cpe_api.c:2648:19: error: this statement may fall through [-Werror=implicit-fallthrough=]
2648 | if (pContext->bAutobootThreadStarted)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/common/drv_dsl_cpe_api.c:2656:13: note: here
2656 | case DSL_AUTOBOOT_CTRL_STOP_PD:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c: In function 'DSL_DRV_PM_CountersReset':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c:2358:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2358 | if (ResetType == DSL_PM_RESET_HISTORY)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c:2361:4: note: here
2361 | case DSL_PM_RESET_TOTAL:
| ^~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c:2365:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2365 | if (ResetType == DSL_PM_RESET_TOTAL)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/pm/drv_dsl_cpe_pm_core.c:2368:4: note: here
2368 | case DSL_PM_RESET_HISTORY_SHOWTIME:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/device/drv_dsl_cpe_device_vrx.c: In function 'DSL_DRV_DEV_AutobootHandleTraining':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/device/drv_dsl_cpe_device_vrx.c:8883:19: error: this statement may fall through [-Werror=implicit-fallthrough=]
8883 | bPreFail = DSL_TRUE;
| ~~~~~~~~~^~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/dsl_cpe_api-ugw_8.5.2.10/src/device/drv_dsl_cpe_device_vrx.c:8889:7: note: here
8889 | case DSL_LINESTATE_EXCEPTION:
| ^~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning for some debugfs entry defined but
unused.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:969:12: error: 'proc_read_genconf' defined but not used [-Werror=unused-function]
969 | static int proc_read_genconf(char *page, char **start, off_t off, int count, int *eof, void *data)
| ^~~~~~~~~~~~~~~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:942:12: error: 'proc_write_wanmib' defined but not used [-Werror=unused-function]
942 | static int proc_write_wanmib(struct file *file, const char *buf, unsigned long count, void *data)
| ^~~~~~~~~~~~~~~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:910:12: error: 'proc_read_wanmib' defined but not used [-Werror=unused-function]
910 | static int proc_read_wanmib(char *page, char **start, off_t off, int count, int *eof, void *data)
| ^~~~~~~~~~~~~~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:892:12: error: 'proc_read_version' defined but not used [-Werror=unused-function]
892 | static int proc_read_version(char *buf, char **start, off_t offset, int count, int *eof, void *data)
| ^~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xway/ltq-ptm-danube/ltq-ptm/ifxmips_ptm_adsl.c:1164:19: error: 'stricmp' defined but not used [-Werror=unused-function]
1164 | static INLINE int stricmp(const char *p1, const char *p2)
| ^~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning due to not handled switch
fallthrough, stack limit and compilation warning in g997 module.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c: In function 'DSL_DRV_PM_CountersReset':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c:2277:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2277 | if (ResetType == DSL_PM_RESET_HISTORY)
| ^
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c:2280:4: note: here
2280 | case DSL_PM_RESET_TOTAL:
| ^~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c:2284:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2284 | if (ResetType == DSL_PM_RESET_TOTAL)
| ^
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/pm/drv_dsl_cpe_pm_core.c:2287:4: note: here
2287 | case DSL_PM_RESET_HISTORY_SHOWTIME:
| ^~~~
cc1: all warnings being treated as errors
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/device/drv_dsl_cpe_device_danube.c: In function 'DSL_DRV_DEV_AutobootHandleTraining':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/device/drv_dsl_cpe_device_danube.c:3189:19: error: this statement may fall through [-Werror=implicit-fallthrough=]
3189 | if (nErrCode != DSL_SUCCESS)
| ^
/__w/openwrt/openwrt/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/device/drv_dsl_cpe_device_danube.c:3197:13: note: here
3197 | case DSL_LINESTATE_IDLE:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/g997/drv_dsl_cpe_api_g997_danube.c: In function 'DSL_DRV_DEV_G997_PowerManagementStateForcedTrigger':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/g997/drv_dsl_cpe_api_g997_danube.c:2532:52: error: bitwise comparison always evaluates to false [-Werror=tautological-compare]
2532 | else if (((nVal >> 4) & 0x15) == 0x9)
| ^~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/g997/drv_dsl_cpe_api_g997_danube.c: In function 'DSL_DRV_DEV_G997_DeltHlogGet':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_ase/ltq-dsl-ase/drv_dsl_cpe_api-3.24.4.4/src/g997/drv_dsl_cpe_api_g997_danube.c:2108:1: error: the frame size of 1056 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
2108 | }
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add multiple patch to make the package compilable again.
Aside from some fixup of obvius wrong code, some real fix were needed.
This fix any compilation warning found on compiling the package on
bcm47xx. (omitted since they are too much)
The real problem of this package was the missing MODULE_LICENSE now
mandatory even without WERROR. Set to Proprietary.
And the big blocker is that Broadcom provided an object file targetting
an old kernel version.
The module on modprobe try to find the symbol printk but printk was
dropped and replaced to _printk.
To handle this change we use objcopy tool to rename the symbol to the
new name permitting a correct modprobe and creation of .ko
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning on 64bit systems.
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/fwcmd.c: In function 'mwl_fwcmd_get_fw_core_dump':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/fwcmd.c:3608:31: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
3608 | (const void *)((u32)pcmd +
| ^
In file included from ./include/linux/device.h:15,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/device.h:3,
from ./include/linux/dma-mapping.h:7,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/dma-mapping.h:3,
from ./include/linux/skbuff.h:31,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/skbuff.h:3,
from ./include/linux/if_ether.h:19,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/if_ether.h:3,
from ./include/linux/etherdevice.h:20,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/etherdevice.h:3,
from /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:20:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c: In function 'pcie_tx_init_ndp':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:38: error: format '%d' expects argument of type 'int', but argument 3 has type 'long unsigned int' [-Werror=format=]
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/dev_printk.h:110:30: note: in definition of macro 'dev_printk_index_wrap'
110 | _p_func(dev, fmt, ##__VA_ARGS__); \
| ^~~
./include/linux/dev_printk.h:144:56: note: in expansion of macro 'dev_fmt'
144 | dev_printk_index_wrap(_dev_err, KERN_ERR, dev, dev_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211/net/cfg80211.h:8828:9: note: in expansion of macro 'dev_err'
8828 | dev_err(&(wiphy)->dev, format, ##args)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:17: note: in expansion of macro 'wiphy_err'
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ^~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:67: note: format string is defined here
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ~^
| |
| int
| %ld
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:38: error: format '%d' expects argument of type 'int', but argument 4 has type 'long unsigned int' [-Werror=format=]
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/dev_printk.h:110:30: note: in definition of macro 'dev_printk_index_wrap'
110 | _p_func(dev, fmt, ##__VA_ARGS__); \
| ^~~
./include/linux/dev_printk.h:144:56: note: in expansion of macro 'dev_fmt'
144 | dev_printk_index_wrap(_dev_err, KERN_ERR, dev, dev_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211/net/cfg80211.h:8828:9: note: in expansion of macro 'dev_err'
8828 | dev_err(&(wiphy)->dev, format, ##args)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:17: note: in expansion of macro 'wiphy_err'
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ^~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.c:338:71: note: format string is defined here
338 | wiphy_err(hw->wiphy, "driver data is not enough: %d (%d)\n",
| ~^
| |
| int
| %ld
CC [M] /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/debugfs.o
In file included from ./include/linux/device.h:15,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/device.h:3,
from ./include/linux/dma-mapping.h:7,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/dma-mapping.h:3,
from ./include/linux/skbuff.h:31,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/skbuff.h:3,
from ./include/linux/if_ether.h:19,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/if_ether.h:3,
from ./include/linux/etherdevice.h:20,
from /home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211-backport/linux/etherdevice.h:3,
from /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.c:19:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.c: In function 'pcie_bf_mimo_ctrl_decode':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.c:1325:37: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
1325 | filename, (unsigned int)fp_data);
| ^
./include/linux/dev_printk.h:110:37: note: in definition of macro 'dev_printk_index_wrap'
110 | _p_func(dev, fmt, ##__VA_ARGS__); \
| ^~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/staging_dir/target-aarch64_cortex-a53_musl/usr/include/mac80211/net/cfg80211.h:8828:9: note: in expansion of macro 'dev_err'
8828 | dev_err(&(wiphy)->dev, format, ##args)
| ^~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.c:1324:17: note: in expansion of macro 'wiphy_err'
1324 | wiphy_err(priv->hw->wiphy, "Error opening %s! %x\n",
| ^~~~~~~~~
cc1: all warnings being treated as errors
make[4]: *** [scripts/Makefile.build:289: /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/tx_ndp.o] Error 1
make[4]: *** Waiting for unfinished jobs....
cc1: all warnings being treated as errors
make[4]: *** [scripts/Makefile.build:289: /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/hif/pcie/pcie.o] Error 1
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/debugfs.c: In function 'mwl_debugfs_regrdwr_read':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-ipq807x_generic/mwlwifi-2023-04-29-6a436714/debugfs.c:1335:43: error: format '%d' expects argument of type 'int', but argument 4 has type 'ssize_t' {aka 'long int'} [-Werror=format=]
1335 | "error: %d(%u 0x%08x 0x%08x)\n",
| ~^
| |
| int
| %ld
1336 | ret, priv->reg_type, priv->reg_offset,
| ~~~
| |
| ssize_t {aka long int}
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Alloc MIB struct dynamically instead to fix compilation warning for
stack limit.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_chromium/vrx518_tc_drv-ugw_8.5.2.10/dcdp/ptm_tc.c: In function 'ptm_tc_get_stats':
/__w/openwrt/openwrt/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_chromium/vrx518_tc_drv-ugw_8.5.2.10/dcdp/ptm_tc.c:463:1: error: the frame size of 1032 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
463 | }
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning for atm_tc module.
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/vrx518_tc_drv-ugw_8.5.2.10/dcdp/atm_tc.c: In function 'print_datetime':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-arm-openwrt-linux-muslgnueabi_musl/linux-ipq40xx_generic/vrx518_tc_drv-ugw_8.5.2.10/dcdp/atm_tc.c:768:32: error: argument to 'sizeof' in 'snprintf' call is the same expression as the destination; did you mean to provide an explicit length? [-Werror=sizeof-pointer-memaccess]
768 | snprintf(buffer, sizeof(buffer), "%s.%06d", tmbuf, (int)datetime->tv_nsec / 1000);
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop set_fs and get_fs since they are not present in kernel > 5.13.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c: In function 'dev_wlc_ioctl':
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:121:14: error: implicit declaration of function 'get_fs'; did you mean 'sget_fc'? [-Werror=implicit-function-declaration]
121 | fs = get_fs();
| ^~~~~~
| sget_fc
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:121:14: error: incompatible types when assigning to type 'mm_segment_t' from type 'int'
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:122:9: error: implicit declaration of function 'set_fs'; did you mean 'sget_fc'? [-Werror=implicit-function-declaration]
122 | set_fs(KERNEL_DS);
| ^~~~~~
| sget_fc
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_generic/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:122:16: error: 'KERNEL_DS' undeclared (first use in this function); did you mean 'KERNFS_NS'?
122 | set_fs(KERNEL_DS);
| ^~~~~~~~~
| KERNFS_NS
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing compilation warning related to if clause not guarding in
wl_iw.c
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_legacy/broadcom-wl-5.10.56.27.3/driver/wl_iw.c: In function 'wl_iw_set_freq':
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_legacy/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:393:9: error: this 'if' clause does not guard... [-Werror=misleading-indentation]
393 | if (fwrq->m > 4000 && fwrq->m < 5000)
| ^~
/__w/openwrt/openwrt/openwrt/build_dir/target-mipsel-openwrt-linux-musl_musl/linux-bcm47xx_legacy/broadcom-wl-5.10.56.27.3/driver/wl_iw.c:396:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the 'if'
396 | chan = wf_mhz2channel(fwrq->m, sf);
| ^~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning for dev_err in rb91x_nand driver.
Fix compilation warning:
drivers/mtd/nand/raw/rb91x_nand.c:289:25: note: in expansion of macro 'dev_err'
289 | dev_err(dev, "failed to get gpios: %d\n",
| ^~~~~~~
drivers/mtd/nand/raw/rb91x_nand.c:289:61: note: format string is defined here
289 | dev_err(dev, "failed to get gpios: %d\n",
| ~^
| |
| int
| %ld
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning for copy_from_user ret value not handled.
Fix compilation warning:
/__w/openwrt/openwrt/openwrt/build_dir/target-mips_mips32_musl/linux-lantiq_ase/ltq-adsl-mei-ase/ltq-adsl-mei/drv_mei_cpe.c: In function 'DSL_BSP_FWDownload':
/__w/openwrt/openwrt/openwrt/build_dir/target-mips_mips32_musl/linux-lantiq_ase/ltq-adsl-mei-ase/ltq-adsl-mei/drv_mei_cpe.c:1623:17: error: ignoring return value of 'copy_from_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
1623 | copy_from_user ((char *) &img_hdr_tmp, buf, sizeof (img_hdr_tmp));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/__w/openwrt/openwrt/openwrt/build_dir/target-mips_mips32_musl/linux-lantiq_ase/ltq-adsl-mei-ase/ltq-adsl-mei/drv_mei_cpe.c:1701:17: error: ignoring return value of 'copy_from_user' declared with attribute 'warn_unused_result' [-Werror=unused-result]
1701 | copy_from_user (mem_ptr, buf + nRead, nCopy);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Comment unused function macronix_nand_block_protection_support since it
does cause boot problem
Fix compilation error:
drivers/mtd/nand/raw/nand_macronix.c:220:13: error: 'macronix_nand_block_protection_support' defined but not used [-Werror=unused-function]
220 | static void macronix_nand_block_protection_support(struct nand_chip *chip)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Comment unused macronix_nand_block_protection_support due to workaround
needed to fix booting
Fix compilation warning:
drivers/mtd/nand/raw/nand_macronix.c:220:13: error: 'macronix_nand_block_protection_support' defined but not used [-Werror=unused-function]
220 | static void macronix_nand_block_protection_support(struct nand_chip *chip)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning for using %d instead of %ld for gpio-latch in
dev_err.
Fix compilation warning:
In file included from ./include/linux/device.h:15,
from ./include/linux/gpio/driver.h:5,
from drivers/gpio/gpio-latch.c:13:
drivers/gpio/gpio-latch.c: In function 'gpio_latch_probe':
drivers/gpio/gpio-latch.c:137:46: error: format '%d' expects argument of type 'int', but argument 4 has type 'long int' [-Werror=format=]
137 | dev_err(dev, "failed to get gpio %d: %d\n", i,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/dev_printk.h:110:30: note: in definition of macro 'dev_printk_index_wrap'
110 | _p_func(dev, fmt, ##__VA_ARGS__); \
| ^~~
./include/linux/dev_printk.h:144:56: note: in expansion of macro 'dev_fmt'
144 | dev_printk_index_wrap(_dev_err, KERN_ERR, dev, dev_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~
drivers/gpio/gpio-latch.c:137:33: note: in expansion of macro 'dev_err'
137 | dev_err(dev, "failed to get gpio %d: %d\n", i,
| ^~~~~~~
drivers/gpio/gpio-latch.c:137:71: note: format string is defined here
137 | dev_err(dev, "failed to get gpio %d: %d\n", i,
| ~^
| |
| int
| %ld
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch commenting unused sdhci function, hopin this will be dropped
when the problem is actually found.
Fix compilation warning:
drivers/mmc/host/sdhci-msm.c:1781:13: error: 'sdhci_msm_set_clock' defined but not used [-Werror=unused-function]
1781 | static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
| ^~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rework some desc dump and dummy pkt function to fix compilation warning.
Fix compilation warning:
drivers/staging/fsl_ppfe/pfe_hif.c: In function 'send_dummy_pkt_to_hif':
drivers/staging/fsl_ppfe/pfe_hif.c:118:19: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
118 | ddr_ptr = (void *)((u64)readl(BMU2_BASE_ADDR + BMU_ALLOC_CTRL));
| ^
drivers/staging/fsl_ppfe/pfe_hif.c:122:20: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
122 | lmem_ptr = (void *)((u64)readl(BMU1_BASE_ADDR + BMU_ALLOC_CTRL));
| ^
drivers/staging/fsl_ppfe/pfe_hif.c: In function 'pfe_hif_desc_dump':
drivers/staging/fsl_ppfe/pfe_hif.c:195:24: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
195 | desc_p = (u32)((u64)desc - (u64)hif->descr_baseaddr_v +
| ^
drivers/staging/fsl_ppfe/pfe_hif.c:195:36: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
195 | desc_p = (u32)((u64)desc - (u64)hif->descr_baseaddr_v +
| ^
drivers/staging/fsl_ppfe/pfe_hif.c:207:19: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
207 | desc_p = ((u64)desc - (u64)hif->descr_baseaddr_v +
| ^
drivers/staging/fsl_ppfe/pfe_hif.c:207:31: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
207 | desc_p = ((u64)desc - (u64)hif->descr_baseaddr_v +
| ^
cc1: all warnings being treated as errors
In file included from ./include/linux/kernel.h:19,
from ./include/linux/list.h:9,
from ./include/linux/wait.h:7,
from ./include/linux/eventfd.h:13,
from drivers/staging/fsl_ppfe/pfe_cdev.c:11:
drivers/staging/fsl_ppfe/pfe_cdev.c: In function 'pfe_cdev_read':
./include/linux/kern_levels.h:5:25: error: format '%lu' expects argument of type 'long unsigned int', but argument 3 has type 'int' [-Werror=format=]
5 | #define KERN_SOH "\001" /* ASCII Start Of Header */
| ^~~~~~
./include/linux/printk.h:422:25: note: in definition of macro 'printk_index_wrap'
422 | _p_func(_fmt, ##__VA_ARGS__); \
| ^~~~
./include/linux/printk.h:132:17: note: in expansion of macro 'printk'
132 | printk(fmt, ##__VA_ARGS__); \
| ^~~~~~
./include/linux/printk.h:580:9: note: in expansion of macro 'no_printk'
580 | no_printk(KERN_DEBUG pr_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~~~
./include/linux/kern_levels.h:15:25: note: in expansion of macro 'KERN_SOH'
15 | #define KERN_DEBUG KERN_SOH "7" /* debug-level messages */
| ^~~~~~~~
./include/linux/printk.h:580:19: note: in expansion of macro 'KERN_DEBUG'
580 | no_printk(KERN_DEBUG pr_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~~~~
drivers/staging/fsl_ppfe/pfe_cdev.c:42:17: note: in expansion of macro 'pr_debug'
42 | pr_debug("%u %lu", link_states[ret].phy_id,
| ^~~~~~~~
./include/linux/kern_levels.h:5:25: error: format '%lu' expects argument of type 'long unsigned int', but argument 3 has type 'size_t' {aka 'unsigned int'} [-Werror=format=]
5 | #define KERN_SOH "\001" /* ASCII Start Of Header */
| ^~~~~~
./include/linux/printk.h:422:25: note: in definition of macro 'printk_index_wrap'
422 | _p_func(_fmt, ##__VA_ARGS__); \
| ^~~~
./include/linux/printk.h:493:9: note: in expansion of macro 'printk'
493 | printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~
./include/linux/kern_levels.h:11:25: note: in expansion of macro 'KERN_SOH'
11 | #define KERN_ERR KERN_SOH "3" /* error conditions */
| ^~~~~~~~
./include/linux/printk.h:493:16: note: in expansion of macro 'KERN_ERR'
493 | printk(KERN_ERR pr_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~~
drivers/staging/fsl_ppfe/pfe_cdev.c:50:17: note: in expansion of macro 'pr_err'
50 | pr_err("Failed to send (%d)bytes of (%lu) requested.\n",
| ^~~~~~
./include/linux/kern_levels.h:5:25: error: format '%lu' expects argument of type 'long unsigned int', but argument 2 has type 'unsigned int' [-Werror=format=]
5 | #define KERN_SOH "\001" /* ASCII Start Of Header */
| ^~~~~~
./include/linux/printk.h:422:25: note: in definition of macro 'printk_index_wrap'
422 | _p_func(_fmt, ##__VA_ARGS__); \
| ^~~~
./include/linux/printk.h:132:17: note: in expansion of macro 'printk'
132 | printk(fmt, ##__VA_ARGS__); \
| ^~~~~~
./include/linux/printk.h:580:9: note: in expansion of macro 'no_printk'
580 | no_printk(KERN_DEBUG pr_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~~~
./include/linux/kern_levels.h:15:25: note: in expansion of macro 'KERN_SOH'
15 | #define KERN_DEBUG KERN_SOH "7" /* debug-level messages */
| ^~~~~~~~
./include/linux/printk.h:580:19: note: in expansion of macro 'KERN_DEBUG'
580 | no_printk(KERN_DEBUG pr_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~~~~
drivers/staging/fsl_ppfe/pfe_cdev.c:57:9: note: in expansion of macro 'pr_debug'
57 | pr_debug("Read of (%lu) bytes performed.\n", sizeof(link_states));
| ^~~~~~~~
cc1: all warnings being treated as errors
In file included from ./include/uapi/linux/posix_types.h:5,
from ./include/uapi/linux/types.h:14,
from ./include/linux/types.h:6,
from ./include/linux/list.h:5,
from ./include/linux/module.h:12,
from drivers/staging/fsl_ppfe/pfe_sysfs.c:7:
drivers/staging/fsl_ppfe/pfe_sysfs.c: In function 'pfe_set_util':
./include/linux/stddef.h:8:14: error: passing argument 2 of 'kstrtoul' makes integer from pointer without a cast [-Werror=int-conversion]
8 | #define NULL ((void *)0)
| ^~~~~~~~~~~
| |
| void *
drivers/staging/fsl_ppfe/pfe_sysfs.c:538:39: note: in expansion of macro 'NULL'
538 | util_do_clear = kstrtoul(buf, NULL, 0);
| ^~~~
In file included from ./include/linux/kernel.h:13,
from ./include/linux/list.h:9:
./include/linux/kstrtox.h:30:69: note: expected 'unsigned int' but argument is of type 'void *'
30 | static inline int __must_check kstrtoul(const char *s, unsigned int base, unsigned long *res)
| ~~~~~~~~~~~~~^~~~
cc1: all warnings being treated as errors
With UTIL compiled on, fix compilation warning:
drivers/staging/fsl_ppfe/pfe_hal.c: In function 'pe_load_ddr_section':
drivers/staging/fsl_ppfe/pfe_hal.c:617:19: error: 'else' without a previous 'if'
617 | } else {
| ^~~~
drivers/staging/fsl_ppfe/pfe_hal.c:622:17: error: break statement not within loop or switch
622 | break;
| ^~~~~
drivers/staging/fsl_ppfe/pfe_hal.c:624:9: error: case label not within a switch statement
624 | case SHT_NOBITS:
| ^~~~
drivers/staging/fsl_ppfe/pfe_hal.c:627:17: error: break statement not within loop or switch
627 | break;
| ^~~~~
drivers/staging/fsl_ppfe/pfe_hal.c:629:9: error: 'default' label not within a switch statement
629 | default:
| ^~~~~~~
drivers/staging/fsl_ppfe/pfe_hal.c: At top level:
drivers/staging/fsl_ppfe/pfe_hal.c:635:9: error: expected identifier or '(' before 'return'
635 | return 0;
| ^~~~~~
drivers/staging/fsl_ppfe/pfe_hal.c:636:1: error: expected identifier or '(' before '}' token
636 | }
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix compilation warning for PHY_INTERFACE_MODE_2500SGMII patch.
Fix compilation warning:
drivers/net/phy/phylink.c: In function 'phylink_get_linkmodes':
drivers/net/phy/phylink.c:360:9: error: enumeration value 'PHY_INTERFACE_MODE_2500SGMII' not handled in switch [-Werror=switch]
360 | switch (interface) {
| ^~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop arm override compile patch. The use is dubious and at times (2016)
it was never explained why this was required.
Krait CPU and Cortex-a15 may be similar but they have some intrinsic
difference. While very similar they differ a lot in additional feature
and also cache configuration.
Also these conflict with raid6 libraty compilation that use specific
workaround not compatible with cortex-a15 and produce compilation
warning.
Fix compilation warning:
cc1: error: switch '-mcpu=cortex-a15' conflicts with switch '-march=armv7-a+simd' [-Werror]
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
