Hardware
--------
MediaTek MT7622
512MB DDR3 RAM
64M SPI-NOR Flash (Winbond W25Q512JV)
MediaTek MT7622 802.11bgn 4T4R WMAC
MediaTek MT7915 802.11ax 4T4R
Marvell AQR1112 100/1000/2500 NBase-T PHY
Holtek HT32F52241 LED controller
Reset Switch
UART
----
CPU UART0 at the pinout next to the Holtek MCU.
Pinout (first pin next to SoC / MCU)
0 3V3
1 RX
2 TX
3 GND
Settings are 115200 8N1.
Opening the case
----------------
Opening the case is not a nice task, as itis glued together. Insert a
flat knife between the front and back casing below the ethernet port.
Open up a gap this way and insert a flat scredriver, remove the knife.
Work your way around the casing by applying force to seperate the front
and back casing. This losens the glue and opens the plastic clips. Be
gentle, as these clips are very cheap and break quickly.
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt".
2. Transfer the OpenWrt sysupgrade image to the device using SCP.
3. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
4. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6
5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock8
$ dd if=openwrt.bin of=/dev/mtdblock9
6. Reboot the device. It should boot into OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 634c13c186)
Add a driver for controlling the RGB LED via Ubiquitis own "LEDBAR" LED
controller based on the Holtek HT32F52241 MCU.
This driver is initially used by the Ubiquiti UniFi 6 LR, however
judging from FCC pictures the MCU is also found on the U6-Mesh as well
as the U6-Extender.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit c9137e2ddf)
The USB ports if a FRIZZ!Box 7320 do not supply power to connected
devices.
Add the GPIOs enabling USB power as regulator, to enable USB power
supply as soon as the USB driver is loaded.
Fixes FS#3624
Signed-off-by: Mathias Kresin <dev@kresin.me>
(cherry picked from commit 6e4e97b2256327bb380ee2a83da9a1ddf657e395)
This fixes 4 security vulnerabilities/bugs:
- CVE-2021-2839 - SSLv2 vulnerability. Openssl 1.1.1 does not support
SSLv2, but the affected functions still exist. Considered just a bug.
- CVE-2021-2840 - calls EVP_CipherUpdate, EVP_EncryptUpdate and
EVP_DecryptUpdate may overflow the output length argument in some
cases where the input length is close to the maximum permissable
length for an integer on the platform. In such cases the return value
from the function call will be 1 (indicating success), but the output
length value will be negative.
- CVE-2021-2841 - The X509_issuer_and_serial_hash() function attempts to
create a unique hash value based on the issuer and serial number data
contained within an X509 certificate. However it was failing to
correctly handle any errors that may occur while parsing the issuer
field (which might occur if the issuer field is maliciously
constructed). This may subsequently result in a NULL pointer deref and
a crash leading to a potential denial of service attack.
- Fixed SRP_Calc_client_key so that it runs in constant time. This could
be exploited in a side channel attack to recover the password.
The 3 CVEs above are currently awaiting analysis.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 482c9ff289)
File extension was truncated for
pending-5.4/770-11-net-ethernet-mtk_eth_soc-avoid-rearming-interrupt-if.pa
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 487b7ae5eb)
After the ABI version rework, packages need to be declared in the order of
their dependencies, so that dependent packages will use the right ABI version
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 75455b75a7ee)
Let's switch to 5.10 now that mac80211 has been updated.
Runtime-tested on ipq806x (Netgear R7800).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry-picked from commit a5c4c40476)
After the ABI version rework, packages need to be declared in the order of
their dependencies, so that dependent packages will use the right ABI version
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This was accidentally dropped in 27a4a71c24
("metadata: handle ABI version rebuild tracking for transient dependencies")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts commit b12288fa69.
The patchelf approach is too fragile, and the only users of this have been
converted to make patching unnecessary
Leave the abi_version_str variable in place in rules.mk
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This adds quirks support to the "ofpart" parser. It's required to
support fixed partitions that require some extra logic.
Right now only BCM4908 binding is supported (BCM4908 requires detecting
currently used "firmware" partition).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The intention is for the loop to timeout if the body does not succeed.
The current logic calls time_is_before_jiffies(timeout) which is false
until after the timeout, so the loop body never executes.
time_is_after_jiffies(timeout) will return true until timeout is less
than jiffies, which is the intended behavior here.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Automatically setup dhcpv4 server just like it's done for dhcpv6.
To select whether odhcpd or dnsmasq are serving DHCPv4 requests there
still is the 'maindhcp' option. To make things less confusing, make
sure things really work out-of-the-box in case dnsmasq is not even
installed at the time the uci-defaults script is being run.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This fixes the build on MIPS BE like ath25 and ath79 target.
We get this error message when linking libwolfssl:
mips-openwrt-linux-musl/bin/ld: /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libwolfssl.so: unknown type [0x7000002a] section `.MIPS.abiflags'
mips-openwrt-linux-musl/bin/ld: /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libwolfssl.so: unknown type [0x7000002a] section `.MIPS.abiflags'
mips-openwrt-linux-musl/bin/ld: skipping incompatible /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libwolfssl.so when searching for -lwolfssl
mips-openwrt-linux-musl/bin/ld: cannot find -lwolfssl
collect2: error: ld returned 1 exit status
This reverts commit 2591c83b34.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes the build on MIPS BE like ath25 and ath79 target.
We get this error message when linking libubox:
mips-openwrt-linux-musl/bin/ld: /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libubox.so: unknown type [0x7000002a] section `.MIPS.abiflags'
mips-openwrt-linux-musl/bin/ld: /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libubox.so: unknown type [0x7000002a] section `.MIPS.abiflags'
mips-openwrt-linux-musl/bin/ld: skipping incompatible /home/hauke/openwrt/openwrt/staging_dir/target-mips_mips32_musl/usr/lib/libubox.so when searching for -lubox
This reverts commit f421fefa8a.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Netgear EX6150 has an Access Point/Extender switch. Set it as
an EV_SW. Otherwise when it's set to Access Point, it will trigger
failsafe mode during boot.
Fixes: FS#3590
Signed-off-by: Kurt Roeckx <kurt@roeckx.be>
This reverts commit 4968fc8fb1 as the bump
to v2021.01 needs swig on the host for pylibfdt which is needed by dtoc
tool to generate .h/.c files from DTBs in SPL for mx6cuboxi_config.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This reverts commit 50a5a8993d as the bump
to 2021.01 unveiled issue with missing swig host tool needed for
mx6cuboxi's SPL.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The SDK and target/toolchain copy the license file into their
directories. During the rename/move from LICENSE to a LICENSES
folder, this has not been updated.
Update it now, and include the new COPYING file.
While at it, improve formatting/indent.
Fixes: 882e301461 ("LICENSES: include all used licenses in
LICENSES directory")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When transmitting to a receiver in dynamic SMPS mode, all transmissions that
use multiple spatial streams need to be sent using CTS-to-self or RTS/CTS to
give the receiver's extra chains some time to wake up.
This fixes the tx rate getting stuck at <= MCS7 for some clients, especially
Intel ones, which make aggressive use of SMPS.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Preparation for supporting dynamic ABI versions that depend on the runtime
configuration. Read the suffix from the staging dir pkginfo version files.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This makes it possible to declare a package ABI_VERSION independent from the
upstream soname by setting PKG_ABI_VERSION in the package makefile.
The library filename is fixed up for files installed to packages and to the
staging dir. References to the original from executables within the same
package are also fixed up
Signed-off-by: Felix Fietkau <nbd@nbd.name>
A stray comma was being appended to the last package version dependency,
causing it to be missed for ABI version checks
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On hardware that supports this, this will improve performance by passing
802.3 frames from the hardware to the stack
Signed-off-by: Felix Fietkau <nbd@nbd.name>
