TP-Link EAP245 v3 is an AC1750 (802.11ac Wave-2) ceiling mount access
point. UART access (for debricking) requires non-trivial soldering.
Specifications:
* SoC: QCA9563 (CPU/DDR/AHB @ 775/650/258 MHz)
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (SoC): b/g/n 3x3
* Wireless 5GHz (QCA9982): a/n/ac 3x3 with MU-MIMO
* Ethernet (QCA8337N switch): 2× 1GbE, ETH1 (802.3at PoE) and ETH2
* Green and amber status LEDs
* Reset switch (GPIO, available for failsafe)
Flashing instructions:
All recent firmware versions (latest is 2.20.0), can disable firmware
signature verification and use a padded firmware file to flash OpenWrt:
* ssh into target device and run `cliclientd stopcs`
* upload factory image via web interface
The stopcs-method is supported from firmware version 2.3.0. Earlier
versions need to be upgraded to a newer stock version before flashing
OpenWrt.
Factory images for these devices are RSA signed by TP-Link. While the
signature verification can be disabled, the factory image still needs to
have a (fake) 1024 bit signature added to pass file checks.
Debricking instructions:
You can recover using u-boot via the serial port:
* Serial port is available from J3 (1:TX, 2:RX, 3:GND, 4:3.3V)
* Bridge R237 to connect RX, located next to J3
* Bridge R225 to connect TX, located inside can on back-side of board
* Serial port is 115200 baud, 8n1, interrupt u-boot by holding ctrl+B
* Upload initramfs with tftp and upgrade via OpenWrt
Device mac addresses:
Stock firmware has the same mac address for 2.4GHz wireless and
ethernet, 5GHz is incremented by one. The base mac address is stored in
the 'default-mac' partition (offset 0x90000) at an offset of 8 bytes.
ART blobs contain no mac addresses.
From OEM ifconfig:
ath0 Link encap:Ethernet HWaddr 74:..:E2
ath10 Link encap:Ethernet HWaddr 74:..:E3
br0 Link encap:Ethernet HWaddr 74:..:E2
eth0 Link encap:Ethernet HWaddr 74:..:E2
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
TP-Link has introduced a compatibility level to prevent certain
downgrades. This information is stored in the soft-version partition,
changing the data length from 0xc to 0x10.
The compatibility level doesn't change frequently. For example, it has
the following values for the EAP245v3 (released 2018-Q4):
* FW v2.2.0 (2019-05-30): compat_level=0
* FW v2.3.0 (2019-07-31): compat_level=0
* FW v2.3.1 (2019-10-29): compat_level=1
* FW v2.20.0 (2020-04-23): compat_level=1
Empty flash values (0xffffffff) are interpreted as compat_level=0.
If a firmware upgrade file has a soft-version block without
compatibility level (data length < 0x10), this is also interpreted as
compat_level=0.
By including a high enough compatibility level in factory images, stock
firmware can be convinced to accept the image. A compatibility level
aware firmware will keep the original value.
Example upgrade log of TP-Link EAP245v3 FWv2.3.0 to FWv2.20.0:
[NM_Debug](nm_fwup_verifyFwupFile) 02073: curSoftVer:2.3.0 Build
20190731 Rel. 51932,newSoftVer:2.20.0 Build 20200423 Rel. 36779
...
AddiHardwareVer check: NEW(0x1) >= CUR(0x0), Success.
...
[NM_NOTICE](updateDataToNvram) 00575: Restore old additionalHardVer:
0x0.(new 0x1)
[NM_NOTICE](updateDataToNvram) 00607: PTN 07: name = soft-version,
base = 0x00092000, size = 0x00000100 Bytes, upDataType = 1,
upDataStart = 7690604b, upDataLen = 00000018
[NM_Debug](updateDataToNvram) 00738: PTN 07: write bytes = 000002eb
Other firmware upgrades have been observed to modify the compabitility
stored level (e.g. TP-Link EAP225-Outdoor FWv1.4.1 to FWv1.7.0).
Therefore, it seems to be the safest option to set the OpenWrt
compatibility level to the highest known value instead of the highest
possible value (0xfffffffe), to ensure users do not get unexpectedly
refused firmware upgrades when using a device reverted back to stock.
To remain compatible with existing devices and not produce different
images, the image builder doesn't store a compatibility level if it is
zero.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The soft-version partition actually contains a header and trailing data:
* header: {data length, [zero]}
* data: {version, bcd encoded date, revision}
The data length is currently treated as a magic number, but should
contain the length of the partition data.
This header is also present the following partitions (non-exhaustive):
* string-based soft-version
* support-list
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Some environments, e.g. first gen WSL, do not support SysV IPC.
Enforce the use of TCP transport instead which should be universally
available.
Fixes: FS#3317
Ref: https://github.com/microsoft/WSL/issues/4067
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This target is still on kernel 4.14, and recent attempts to move it to
kernel 5.4 have not led to success. The device tester reported that it
wouldn't boot with the following messages:
From sysupgrade:
Press any key within 4 seconds to enter setup....
loading kernel from nand... OK
setting up elf image... OK
jumping to kernel code
At this point the system hangs.
From CompactFlash:
Press any key within 4 seconds to enter setup....
Booting CF
Loading kernel... done
setting up elf image... kernel out of range kernel loading failed
The tester reported that the same was observed with current master
(kernel 4.14) as well. This looks like some kernel size restriction.
Since this target is quite old and only supports one device, and since
nobody else seemed interested in working on this for quite some time,
I decided to not put further work into analyzing the problem and drop
this together with the other 4.14-only targets.
Patchwork series:
https://patchwork.ozlabs.org/project/openwrt/list/?series=197066&state=*
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This sorts the added tools and builddir dependencies alphabetically
to make it easier to find something in the Makefile.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
These tools have been used by the orion target which has been
removed in Jan 2020 [1].
Both were specifically meant for the WRT350Nv2, which is not
supported anymore.
So, let's remove them as well.
[1] 89f2deb372 ("orion: remove unmaintained target")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Instead of using http and https for source downloads from
downloads.openwrt.org, always use https for it's better security.
Signed-off-by: Paul Spooren <mail@aparcar.org>
SELinux uses extended attributes to store SELinux security contexts.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[rebase, add commit message]
Signed-off-by: W. Michael Petullo <mike@flyn.org>
lzma-old host package is required for building ath79 images, as
mksquashfs-lzma is required for generating netgear images.
Fixes commit 4e4ee46495 ("ar71xx: drop target")
Signed-off-by: David Bauer <mail@david-bauer.net>
The kernel has become too big again for the ar9344-based TP-Link
CPE/WBS devices which still have no firmware-partition splitter.
Current buildbots produce a kernel size of about 2469 kiB, while
the partition is only 2048 kiB (0x200000). Therefore, increase it
to 0x300000 to provide enough room for this and, hopefully, the
next kernel.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This target has been mostly replaced by ath79 and won't be included
in the upcoming release anymore. Finally put it to rest.
This also removes all references in packages, tools, etc. as well as
the uboot-ar71xx and vsc73x5-ucode packages.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The release notes says this:
As already said, the changes since 2.1.1 are primarily bug fixes, addressing
compiler warnings and issues reported by diagnostic tools, but also build
failures for some configurations.
https://lists.infradead.org/pipermail/linux-mtd/2020-July/081299.html
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
TP-LINK published a firmware update for the archer c6 v2.
This updates also reached the factory devices. Newer software version
rejects downgrading to 1.2.x. Use 1.9.x to allow installing the factory images
and have a little bit time to change it again.
Tested on archer c6 v2 with firmware 1.3.1
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The TL-WPA8630P v2 is a HomePlug AV2 compatible device with a QCA9563 SoC
and 2.4GHz and 5GHz WiFi modules.
Specifications
--------------
- QCA9563 750MHz, 2.4GHz WiFi
- QCA9888 5GHz WiFi
- 8MiB SPI Flash
- 128MiB RAM
- 3 GBit Ports (QCA8337)
- PLC (QCA7550)
MAC address assignment
----------------------
WiFi 2.4GHz and LAN share the same MAC address as printed on the label.
5GHz WiFi uses LAN-1, based on assumptions from similar devices.
LAN Port assignment
-------------------
While there are 3 physical LAN ports on the device, there will be 4
visible ports in OpenWrt. The fourth port (internal port 5) is used
by the PowerLine Communication SoC and thus treated like a regular
LAN port.
Versions
--------
Note that both TL-WPA8630 and TL-WPA8630P, as well as the different
country-versions, differ in partitioning, and therefore shouldn't be
cross-flashed.
This adds support for the two known partitioning variants of the
TL-WPA8630P, where the variants can be safely distinguished via the
tplink-safeloader SupportList. For the non-P variants (TL-WPA8630),
at least two additional partitioning schemes exist, and the same
SupportList entry can have different partitioning.
Thus, we don't support those officially (yet).
Also note that the P version for Germany (DE) requires the international
image version, but is properly protected by SupportList.
In any case, please check the OpenWrt Wiki pages for the device
before flashing anything!
Installation
------------
Installation is possible from the OEM web interface. Make sure to
install the latest OEM firmware first, so that the PLC firmware is
at the latest version. However, please also check the Wiki page
for hints according to altered partitioning between OEM firmware
revisions.
Additional thanks to Jon Davies and Joe Mullally for bringing
order into the partitioning mess.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
[minor DTS adjustments, add label-mac-device, drop chosen, move
common partitions to DTSI, rename de to int, add AU support strings,
adjust TPLINK_BOARD_ID, create common node in generic-tp-link.mk,
adjust commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
SELinux support requires setting the appropriate SELinux security context
to files and directories, which needs to happen at build time in order
to support read-only root filesystem scenarios. In order to create these
security contexts, we will have to run some SELinux-specific tools on
the host machine, but that requires root access. This adds support for
fakeroot, which the build process will use to run the SELinux security
context creation and the image creation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Apply to current master, and adjust commit message
Thomas' original work is available at
http://lists.infradead.org/pipermail/openwrt-devel/2019-November/025976.html.
Signed-off-by: W. Michael Petullo <mike@flyn.org>
[add rules.mk FAKEROOT variable]
Signed-off-by: Paul Spooren <mail@aparcar.org>
[update, fix macos build]
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The variable in the case argument was mistyped, so the case always
checked against an empty string and never matched.
Fix the variable name. Add a PKG_RELEASE to Makefile so we can bump it.
Fixes: d6de31310c ("cmake: restore parallel build support for bootstrap")
Signed-off-by: Piotr Stefaniak <pstef@freebsd.org>
[add commit message, add PKG_RELEASE, fix commit title, add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit 685570858d.
The commit had several formal flaws, revert it and hopefully apply
it properly next time.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The variable in the case argument was mistyped, so the case always
checked against an empty string and never matched.
Fix the variable name.
Signed-off-by: Piotr Stefaniak <pstef@freebsd.org>
[add commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
By using localtime() to determine the timestamp that goes into factory
images, the resulting image depends on the timezone of the build system.
Use gmtime() instead, which results in more reproducible images.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
TP-Link RE200 v3 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN like the v2.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- 8x LED (GPIO-controlled), 2x button
Unverified:
- UART header on PCB (57600 8n1)
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
MAC address assignment has been done according to the RE200 v2.
The label MAC address matches the OpenWrt ethernet address.
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Recovery
--------
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.
The device has not been opened for adding support. However, it is expected
that the behavior is similar to the RE200 v2. Instructions for serial console
and recovery may be checked out in commit 6d6f36ae78 ("ramips: add support
for TP-Link RE200 v2") or on the device's Wiki page.
Signed-off-by: Richard Fröhning <misanthropos@gmx.de>
[adjust commit title/message, sort support list]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For the TP-Link 4M devices with tplink-v2-image recipe
(mktplinkfw2.c), there are two different flash layouts based
on the size of the (u)boot partition:
device uboot OEM firmware OpenWrt (incl. config)
tl-wr840n-v5 0x20000 0x3c0000 0x3d0000
tl-wr841n-v14 0x10000 0x3d0000 0x3e0000
In both cases, the 0x10000 config partition is used for the firmware
partition as well due to the limited space available and since it's
recreated by the OEM firmware anyway.
However, the TFTP flashing process will only copy data up to the
size of the initial (OEM) firmware size. Therefore, while we can
use the bigger partition to have additional erase blocks on the
device, we have to limit the image sizes to the TFTP limits.
So far, only one layout definition has been set up in mktplinkfw2.c
for 4M mediatek devices. This adds a second one and assigns them
to the devices so the image sizes are correctly restrained.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The stored source code of flock contains the version string of version
2.18, reflect that in the Makefile.
Motivation is the tracking of changes in the buildsystem, which requires
versioning of packages.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Comparing the in tree stored source file of sstrip suggests it's version
2.0[0], reflect that in the Makefile.
Motivation is the tracking of changes in the buildsystem, which requires
versioning of packages.
[0]: df4426a0f0 (diff-d3ba694d91432a068d5d3b36abf8cd0f)
Signed-off-by: Paul Spooren <mail@aparcar.org>
There is no versioning information in the firmware-utils code nor the
Makefile. Consider it as first release by adding PKG_RELEASE.
Motivation is the tracking of changes in the buildsystem, which requires
versioning of packages.
Also update copyright.
Signed-off-by: Paul Spooren <mail@aparcar.org>
There is no versioning information in the patch-image code nor the
Makefile. Consider it as first release by adding PKG_RELEASE.
Motivation is the tracking of changes in the buildsystem, which requires
versioning of packages.
Also update copyright.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This applies to tools directory what has been done for package/ in
commit 9c170cb92f ("package: drop PKG_VERSION for purely local
packages"):
In the package guidelines, PKG_VERSION is supposed to be used as
"The upstream version number that we're downloading", while
PKG_RELEASE is referred to as "The version of this package Makefile".
Thus, the variables in a strict interpretation provide a clear
distinction between "their" (upstream) version in PKG_VERSION and
"our" (local OpenWrt trunk) version in PKG_RELEASE.
For local (OpenWrt-only) packages, this implies that those will only
need PKG_RELEASE defined, while PKG_VERSION does not apply following
a strict interpretation. While the majority of "our" packages actually
follow that scheme, there are also some that mix both variables or
have one of them defined but keep them at "1".
This is misleading and confusing, which can be observed by the fact
that there typically either one of the variables is never bumped or
the choice of the variable to increase depends on the person doing the
change.
Consequently, this patch aims at clarifying the situation by
consistently using only PKG_RELEASE for "our" packages. For tools/,
only three packages were affected. This fixes two of them, and
leaves the remaining wrt350nv2-builder untouched, as the code there
seems to have some versioning of its own that is treated as upstream
version in PKG_VERSION.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds new strings to the support list for the TP-Link CPE210 v3
that are supposed to work with the existing setup.
Without it, the factory image won't be accepted by the vendor UI on
these newer revisions.
Tested on a CPE210 v3.20 (EU).
Ref: https://forum.openwrt.org/t/build-for-cpe210-v3-20/68000
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Firmware is binary blob, so there are barely any NULL terminated strings
expected, so we should probably convert all chars into u8 types, and
after that it's clear, that using strcpy doesn't make sense anymore.
This is rather theoretical stuff, but `uint8_t name[PART_NAME_LENGTH]`
means, that you can supply PART_NAME_LENGTH sized name, not
PART_NAME_LENGTH-1 name when NULL terminated.
Ref: https://github.com/openwrt/openwrt/pull/2274
Fixes: 04cb651376 ("firmware-utils: mkfwimage: fix more errors reported by gcc-6/7/9")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add missing calls to `free` for variable `filebuffer`.
Add missing calls to `fclose` for variables `fd` and `fd_out`.
Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
This device uses the same hardware as RE650 v1 which got supported in
8c51dde.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin
from the RE500 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
[remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep
state_default in DTS files, fix label-mac-device, use lower case
for WiFi LEDs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link RE220 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.
This port of OpenWRT leverages work done by Andreas Böhler <dev@aboehler.at>
for the TP-Link RE200 v2 as both devices share the same SoC, flash layout
and GPIO pinout.
Specifications
MediaTek MT7628AN (580 Mhz)
64 MB of RAM
8 MB of FLASH
2T2R 2.4 GHz and 1T1R 5 GHz
1x 10/100 Mbps Ethernet
UART header on PCB (57600 8n1)
8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled separately.
Web Interface Installation
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Signed-off-by: Rowan Border <rowanjborder@gmail.com>
TP-Link CPE610 v2 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of DDR2 RAM
- 8 MB of SPI-NOR Flash
- 23dBi high-gain directional 2×2 MIMO antenna and a
dedicated metal reflector
- Power, LAN, WLAN5G green LEDs
- 3x green RSSI LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
This patch changes the version code of the image header
from `1.1.99_0.0.0.0` to `99.99.99_99.99.99.99`. This
is neccessary on some devices where the stock firmware
checks the version field, possibly preventing third-party
firmware from being installed.
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
TP-Link RE450 v3 is a dual band router/range-extender based on
Qualcomm/Atheros QCA9563 + QCA9880.
This device is nearly identical to RE450 v2 besides a modified flash
layout (hence I think force-flashing a RE450v2 image will lead to at
least loss of MAC address).
Specification:
- 775 MHz CPU
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 1x 10/100/1000 Mbps Ethernet (AR8033 PHY)
- 7x LED, 4x button-
- possible UART header on PCB¹
Flash instruction:
Apply factory image in OEM firmware web-gui.
¹ Didn't check to connect as I didn't even manage to connect on
RE450v2 (AFAIU it requires disconnecting some resistors, which I was
too much of a coward to do). But given the similarities to v2 I
think it's the same or very similar procedure (and most likely also
the only way to debrick).
Signed-off-by: Andreas Wiese <aw-openwrt@meterriblecrew.net>
[remove dts-v1 and compatible in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fixes the following build error with GCC 10:
/usr/bin/ld: read_fs.o:(.bss+0x0): multiple definition of `swap'; mksquashfs.o:(.bss+0x1b2a88): first defined here
And a compile warning.
Fixes: FS#3104, FS#3119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some autotools based build systems are using autoconf-archive scripts
and are expecting them to almost always be available. This is not
required for regular releases as tar balls generated for releases
commonly have existing configure script. This is rather intended to be
used with autotools.mk's autoreconf and in cases it is not always
possible to get release tar ball.
Including this adds little to no overhead in terms of build time as
those are just m4 scripts copied to an appropriate location.
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
[fixed From: to match SoB]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit adds support for Ubiquiti devices based on the XC board
type, such as the PowerBeam 5AC 500. The factory binary structure is
the same as the WA type.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
also change the download source to https and add a mirror
drop merged patches
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[Add extra changes to compile on FreeBSD, merge two patches]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
macos doesn't define a loff_t type, the native off_t type being 64bit
anyway.
Persuade e2fsprogs to accept off_t instead on macos
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Update xz to 5.2.5
Disable NLS support to be consistent with other tools such as bison, e2fsprogs
and sed.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Update findutils to 4.7.0
Remove patches
Enable pthreads
Disable NLS support to be consistent with other tools such as bison, e2fsprogs
and sed.
Disable selinux support to be consistent with other tools such as sed and tar
Disable rpath as we don't need hardcoded paths
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Remove libressl patches; they are no longer needed as LibreSSl adde
support
Replace qt tests patch with one that disables all of them.
Refresh remaining one.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Add GPT support to ptgen, so we can generate EFI bootable images.
Introduced two options:
-g generate GPT partition table
-G GUID use GUID for disk and increase last bit for all partitions
We drop The alternate partition table to reduce size, This may cause
problems when generate vmdk images or vdi images. We have to pad enough
sectors when generate these images.
Signed-off-by: 李国 <uxgood.org@gmail.com>
[fixed compilation on macOS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The last couple of TP-Link firmware releases for Archer C6 v2 (EU)
have switched to version 1.2.x. Bump the soft_ver to "1.2.1" to
allow firmware updates from the vendor web interface.
TP-Link vendor firmware releases supported by this change:
* Archer C6(EU)_V2_200110: soft_ver:1.2.1 Build 20200110 rel.60119
* Archer C6(EU)_V2_191014: soft_ver:1.2.0 Build 20191014 rel.33289
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
In order to build squashfskit with GCC10, this backport from upstream is needed.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[increase PKG_RELEASE]
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
TP-Link Archer C60 v3 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561 + QCA9886.
It seems to be identical to the v2 revision, except that
it lacks a WPS LED and has different GPIO for amber WAN LED.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 6x LED, 2x button
- UART header on PCB
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~30 second to complete recovery
While TFTP works for OpenWrt images, my device didn't accept the
only available official firmware "Archer C60(EU)_V3.0_190115.bin".
In contrast to earlier revisions (v2), the v3 contains the (same)
MAC address twice, once in 0x1fa08 and again in 0x1fb08.
While the partition-table on the device refers to the latter, the
firmware image contains a different partition-table for that region:
name device firmware
factory-boot 0x00000-0x1fb00 0x00000-0x1fa00
default-mac 0x1fb00-0x1fd00 0x1fa00-0x1fc00
pin 0x1fd00-0x1fe00 0x1fc00-0x1fd00
product-info 0x1fe00-0x1ff00 0x1fd00-0x1ff00
device-id 0x1ff00-0x20000 0x1ff00-0x20000
While the MAC address is present twice, other data like the PIN isn't,
so with the partitioning from the firmware image the PIN on the device
would actually be outside of its partition.
Consequently, the patch uses the MAC location from the device (which
is the same as for the v2).
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The pkgconf fork filters -I and -L flag values from .pc files which match
pkgconf's builtin system directory value.
During configure, pkgconf derives the default system include and library
search path values from exec_prefix, which is set to staging_dir/host in
the host tool build phase.
Due to that, pkgconf will drop all -I and -L flags pointing to
staging_dir/host/include or staging_dir/host/lib, unless invoked with
--keep-system-cflags and --keep-system-libs respectively, breaking our
kernel libelf discovery / stack validation workarounds.
In order to inhibit the filtering, add --keep-system-cflags and
--keep-system-libs to our pkg-config shell wrapper.
Fixes: GH#2832
Fixes: 867298cf47 ("tools/pkg-config: Replace with pkgconf")
Ref: https://lists.infradead.org/pipermail/openwrt-devel/2020-March/022182.html
Ref: https://git.openwrt.org/fe43969336201f2cc7d103b68fd6e65989bee184
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Petr Štetiar <ynezz@true.cz>
As part of the kernel build process there are utilities built to run on
the host system that expect linux kernel headers to be available.
Unfortunately macos/darwin doesn't have these headers.
vdso2c requires types.h so provide a minimal stub to satisfy it.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Code was attempting to determine the size of the file
before it was actually known and allocating insufficient
memory space. Images above a certain size caused a
segmentation fault. Moving the calloc() ensured ensured
that large images didn't result in a buffer overflow on
memcpy().
Signed-off-by: Michael T Farnworth <michael@turf.org>
[fixed name in From to match one in SoB]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
pkgconf is a newer, actively maintained implementation of pkg-config that
supports more aspects of the pkg-config file specification and provides a
library interface that applications can use to incorporate intelligent
handling of pkg-config files into themselves (such as build file
generators, IDEs, and compilers). Through its pkg-config compatibility
interface (activated when it is run as "pkg-config"), it also can
completely replace the original implementation.
It is also lighterweight and does not require glib2, as pkg-config does.
On other distros, pkgconf is symlinked to pkg-config. For simplicity here,
it is renamed to pkg-config.real, as in the original package.
Initial results have been positive. As before, pkgconf works as long as
the pkg-config files point to the proper paths.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[backported upstream fix for Meson]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Currently, if "make tools/install" is called after tools have already
been installed, a symbolic link named "lib" will be created inside
$(STAGING_DIR_HOST)/lib, pointing to "lib" (i.e. itself).
During tools/prepare, a "lib64" symlink is created inside
$(STAGING_DIR_HOST) that points to "lib" (also inside
$(STAGING_DIR_HOST)).
If tools/prepare is called and the "lib64" symlink already exists, then
ln will treat it as a directory and instead create a symlink named "lib"
inside of that directory.
This adds the -n option for ln so that $(STAGING_DIR_HOST)/lib64 is
always treated as a normal file (the link name), not as a directory.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
Update bison to 3.5.1
Use POSIX threads as the previous option is no longer valid
Disable NLS support to be consistent with other tools such as e2fsprogs and sed
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
TP-Link RE200 v2 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN.
Specifications
--------------
- MediaTek MT7628AN (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled
separately.
MAC addresses
-------------
The MAC address assignment matches stock firmware, i.e.:
LAN : *:0D
2.4G: *:0E
5G : *:0F
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. Simply flash
the -factory.bin from OEM. In contrast to a stock firmware, this will not
overwrite U-Boot.
Serial console
--------------
Opening the case is quite hard, since it is welded together. Rename the
OpenWrt factory image to "test.bin", then plug in the device and quickly
press "2" to enter flash mode (no line feed). Follow the prompts until
OpenWrt is installed.
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console.
Additonal notes
---------------
It is possible to flash back to stock by using tplink-safeloader to create
a sysupgrade image based on a stock update. After the first boot, it is
necessary upgrade to another stock image, otherwise subsequent boots
fail with LZMA ERROR 1 and you have to attach serial to recover the device.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
[remove DEVICE_VARS change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves the TP-Link TL-WA850RE v2 to dynamic partitioning and
will allow to use this for ath79 as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Update bison to 3.5
Release notes:
https://lists.gnu.org/archive/html/info-gnu/2019-12/msg00002.html
Note for future: release notes mention that YYPRINT macro is
declared deprecated, but apparently still works for now. I found
one possible use of that in scripts/config/zconf.tab.c_shipped
That might be modernized at some point, but as the file is synced
with the one from upstream Linux, it might get fixed there.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
This patch updates "soft_ver" for TP-Link Archer C6 v2 (EU).
It makes possible to upload OpenWrt on lastest vendor's firmware
as the web-based updater checks for major.minor version during upload.
Due to that on next major/minor version update TP-Link will stop
us from using the web-based firmware update tool, so it will
require a new patch on soft_ver to match major and minor version.
Up to today's latest stock firmware the patch (major.minor.patch)
version does not matters, that allows downgrade from 1.1.4 to 1.1.1
but do not allow downgrade from 1.1.X to 1.0.X.
Signed-off-by: Anderson Vulczak <andi@andi.com.br>
Specification:
SoC: MediaTek MT7628AN
RAM: 64MiB
Flash: 8MiB
Wifi:
- 2.4GHz: MT7628AN
- 5GHz: MT7612EN
LAN: 1x 10/100 Mbps
Flash instructions:
Flash factory image through stock firmware WEB UI.
Back to stock is possible by using TFTP and stripping down the Firmware
provided by TP-Link to a initramfs.
The flash space between 0x650000 and 0x7f0000
is blank in the stock firmware so I left it out as well.
Signed-off-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
Add missing calls to `free` for variable `mem`.
Add missing call to `fclose` for variable `f`.
The same changes were made in both `mkfwimage.c` and `mkfwimage2.c`.
Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
Add missing `fclose` calls for file pointers `kern_fp`, `fs_fp`
and `out_fp`.
Not closing files could lead to resource leaks.
Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
Add missing calls to `free` for variable `buffer`.
This could lead to a memory leak.
Add missing call to `close` for file pointer `fdin`.
This could lead to a resource leak.
Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
Add missing calls to `fclose` in functions `write_img`, `write_rootfs`
and `write_kernel`.
The not-closed files could lead to resource leaks.
Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
This commit adds support for Ubiquiti ToughSwitch XP (and probably also
EdgeSwitch XP) devices. They are mostly based on the same hardware as
MX devices.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
TP-Link RE200 v1 is a wireless range extender with Ethernet and 2.4G and 5G
WiFi with internal antennas. It's based on MediaTek MT7620A+MT7610EN.
Specifications
--------------
- MediaTek MT7620A (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 1x 10/100 Mbps Ethernet
- UART header on PCB (57600 8n1)
- 8x LED (GPIO-controlled; only 6 supported), 2x button
There are 2.4G and 5G LEDs in red and green which are controlled
separately. The 5G LED is currently not supported, since the GPIOs couldn't
be determined.
Installation
------------
Web Interface
-------------
It is possible to upgrade to OpenWrt via the web interface. However, the
OEM firmware upgrade file is required and a tool to fix the MD5 sum of
the header. This procedure overwrites U-Boot and there is not failsafe /
recovery mode present! To prepare an image, you need to take the header
and U-Boot (i.e. 0x200 + 0x20000 bytes) from an OEM firmware file and
attach the factory image to it. Then fix the header MD5Sum1.
Serial console
--------------
Opening the case is quite hard, since it is welded together. Rename the
OpenWrt factory image to "test.bin", then plug in the device and quickly
press "2" to enter flash mode (no line feed). Follow the prompts until
OpenWrt is installed.
Unfortunately, this devices does not offer a recovery mode or a tftp
installation method. If the web interface upgrade fails, you have to open
your device and attach serial console. Since the web upgrade overwrites
the boot loader, you might also brick your device.
Additional notes
----------------
MAC address assignment is based on stock-firmware. For me, the device
assigns the MAC on the label to Ethernet and the 2.4G WiFi, while the 5G
WiFi has a separate MAC with +2.
*:88 Ethernet/2.4G label, uboot 0x1fc00, userconfig 0x0158
*:89 unused userconfig 0x0160
*:8A 5G not present in flash
This seems to be the first ramips device with a TP-Link v1 header. The
original firmware has the string "EU" embedded, there might be some region-
checking going on during the firmware upgrade process. The original
firmware also contains U-Boot and thus overwrites the boot loader during
upgrade.
In order to flash back to stock, the first header and U-Boot need to be
stripped from the original firmware.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
This adds a "factory" image for the aircube-isp devices. Note that the
firmware can't be uploaded without prior special preparation. For the
most recent instructions on how to do that, visit the OpenWRT wiki page
of the Ubiquiti airCube ISP for details:
https://openwrt.org/toh/ubiquiti/ubiquiti_aircube_isp
Current procedure:
With the original firmware 2.5.0 it is possible to upload and execute a
script via the configuration. To do that download and unpack the
original configuration, adapt uhttpd config to execute another lua
handler (placed in the config directory) and pack and upload it again.
The lua handler can call a script that mounts an overlayfs and modifies
the "fwupdate.real" binary so that an unsigned image is accepted. The
overlayfs is necessary because a security system (called tomoyo) doesn't
allow binaries in other locations than /sbin/fwupdate.real (and maybe
some more) to access the flash when executed via network.
A big thanks to Torvald Menningen (Snap) from the OpenWRT forum for
finding out how to patch the binary so that it accepts an unsigned
image.
The current step-by-step procedure is:
- Use a version 2.5.0 of the original firmware. This is important
because a binary file will be modified.
- Download a configuration.
- Unpack it (it's just a tar gz file without an ending).
- Add the following to uhttpd:
``````
config 'uhttpd' 'other'
list listen_http 0.0.0.0:8080
list listen_http [::]:8080
option 'home' '/tmp/persistent/config/patch/www'
option lua_prefix '/lua'
option lua_handler '/tmp/persistent/config/patch/handler.lua'
``````
- Create a `patch` subfolder.
- Create a `patch/www` subfolder.
- Create a `patch/handler.lua` with the following content:
``````
function handle_request(env)
uhttpd.send("Status: 200 OK\r\n")
uhttpd.send("Content-Type: text/plain\r\n\r\n")
local command = "/bin/sh /tmp/persistent/config/patch/patch.sh 2>&1"
local proc = assert(io.popen(command))
for line in proc:lines() do
uhttpd.send(line.."\r\n")
end
proc:close()
end
``````
- Create a `patch/patch.sh` with the following content:
``````
#!/bin/sh -x
set -e
set -u
set -x
UBNTBOX_PATCHED="/tmp/fwupdate.real"
MD5FILE="/tmp/patchmd5"
cat <<EOF > ${MD5FILE}
c33235322da5baca5a7b237c09bc8df1 /sbin/fwupdate.real
EOF
# check md5 of files that will be patched
if ! md5sum -c ${MD5FILE}
then
echo "******** Error when checking files. Refuse to do anything. ********"
exit 0
fi
# prepare some overlay functionality
LOWERDIR="/tmp/lower_root"
mkdir -p ${LOWERDIR}
mount -t squashfs -oro /dev/mtdblock3 ${LOWERDIR}
overlay_some_path()
{
PATH_TO_OVERLAY=$1
ALIAS=$2
UPPERDIR="/tmp/over_${ALIAS}"
WORKDIR="/tmp/over_${ALIAS}_work"
mkdir -p ${UPPERDIR}
mkdir -p ${WORKDIR}
mount -t overlay -o lowerdir=${LOWERDIR}${PATH_TO_OVERLAY},upperdir=${UPPERDIR},workdir=${WORKDIR} overlay ${PATH_TO_OVERLAY}
}
# patch the ubntbox binary.
overlay_some_path "/sbin" "sbin"
echo -en '\x10' | dd of=/sbin/fwupdate.real conv=notrunc bs=1 count=1 seek=24598
echo "******** Done ********"
``````
- Repack the configuration.
- Upload it via the normal web interface.
- Wait about a minute. The webserver should restart.
- Now there is a second web server at port 8080 which can call the lua
script. Visit the page with a web browser. Link is for example
http://192.168.1.1:8080/lua
- You should see the output of the script with a "*** Done ***" at the
end. Note that the patches are not permanent. If you restart the
router you have to re-visit the link (but not re-upload the config).
- Now you can upload an unsigned binary via the normal web interface.
Signed-off-by: Christian Mauderer <oss@c-mauderer.de>
Its way more trouble to update this to a newer version of qemu than it
is to backport the two additional features we need.
Signed-off-by: Brett Mastbergen <bmastbergen@untangle.com>
This replaces tabs by spaces when preceding an equal sign. This improves
consistency in the file and makes the indent look correct on all platforms.
While at it, also fix one case of inconsistent leading spaces.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch is based on #1689 and adds support for TP-Link Archer
C6 v2 (US) and A6 (US/TW).
The hardware is the same as EU and RU variant, except for GPIOs
(LEDS/Buttons), flash(chip/partitions) and UART being available
on the board.
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q127CS1G (16MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) QCA9563 integrated (3x3)
- 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: 115200, 8n1 (header available on board)
Known issues:
- Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range.
Flash instructions:
Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin
via the router Web interface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
tftp root directory renamed to ArcherA6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the
reset button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing
Flash partitioning: I've followed #1689 for defining the partition layout
for this patch. The partition named as "tplink" @ 0xfd0000 is marked
as read only as it is where some config for stock firmware are stored.
On stock firmware those stock partitions starts at 0xfd9400 however
I had not been able to make it functional starting on the same address as
on stock fw, so it has been partitioned following #1689 and not the stock
partition layout for this specific partition. Due to that firmware/rootfs
partition lenght is 0xf80000 and not 0xf89400 as stock.
According to the GPL code, the EU/RU/JP variant does have different GPIO pins
assignment to LEDs and buttons, also the flash memory layout is different.
GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz
Signed-off-by: Anderson Vulczak <andi@andi.com.br>
[wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases
to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
According to the SourceForge page, the project is migrating to GitHub.
Thus, change the source of the package to GitHub.
Signed-off-by: David Bauer <mail@david-bauer.net>
"2.0" instead of "2.00" is sufficient and more in line with the
other definitions.
Signed-off-by: Bernhard Geier <freifunk@geierb.de>
[commit message/title adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for a popular low-cost 5GHz N based AP
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
This adds support for a popular low-cost 5GHz N based AP
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
This adds support for a popular low-cost 2.4GHz N based AP
Specifications:
SoC: Qualcomm Atheros QCA9533 (650MHz)
RAM: 64MB
Storage: 8 MB SPI NOR
Wireless: 2.4GHz N based built into SoC 2x2
Ethernet: 2x 100/10 Mbps, integrated into SoC
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
This also applies some minor changes to the common DTSI:
- use &wmac for label-mac-device, as this one is actually set up in
common DTSI
- move ð0 to parent DTSI
- fix several leading spaces, added/removed newlines
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[DTS style fixes/improvements, updated commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit 43365ca662 ("Do not use $(V) - force AM_V=1") as
it breaks verbose output in automake packages, deviating from the
upstream and expected behaviour.
As you can see, neither make command outputs the expected verbose
compile command lines:
```
$ make package/mtd-utils/{clean,compile} V=sc
...
CCLD lsmtd
CC nand-utils/nanddump.o
CCLD nanddump
...
```
```
$ make -C build_dir/target*/mtd-utils-2.1.1 clean
...
$ make -C build_dir/target*/mtd-utils-2.1.1 V=1
...
CC lib/libmtd.o
CC lib/libfec.o
CC lib/common.o
CC lib/libcrc32.o
```
The original reason for this commit was some packages failing to build
if V is set to something other than 0 or 1. See the discussion in PR
https://github.com/openwrt/openwrt/pull/2481 for how to fix this in the
package Makefile.
Ref: PR#2481
Acked-by: Mirko Vogt <mirko-openwrt@nanl.de>
Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
[commit title/description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
TP-Link WBS210 v2 is an outdoor wireless CPE for 2.4 GHz with
two Ethernet ports based on Atheros AR9344
The device is the same as TP-Link CPE220 v2, but with higher TX power (27 dBm
instead of 12 dBm) and two antenna connectors instead of built-in antennas.
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP: 192.168.0.100
Stock device TFTP adress: 192.168.0.254
The TP-Link WBS devices use the same GPIOs as the CPE devices,
except for the link4 LED. For this one, WBS devices use "2", while
CPE devices use "16". (Tested on WBS210 v2)
Signed-off-by: Bernhard Geier <freifunk@geierb.de>
[added comment about GPIO]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"$(STAGING_DIR)/include" was carried over from buildroot-ng to OpenWrt
in commit 60c1f0f64d. buildroot has
dropped this directory a long time ago.
In OpenWrt the directory is still created by the PrepareStaging macro
and is part of the default TARGET_CPPFLAGS. But nothing at all installs
headers into this directory, nor should anything be installed under this
path.
Removing this directory from TARGET_CPPFLAGS will cut down the log noise
a bit. Not only will CPPFLAGS be shorter, there will be less warnings
set off by "-Wmissing-include-dirs" (or even failures when paired with
"-Werror"). After all the directory does not even _exist_ in the SDKs,
which are used on the build bots when building packages (see [1] and
[2]).
make[8]: Entering directory '/builder/shared-workdir/build/sdk/build_dir/target-aarch64_generic_musl/libmbim-1.20.0/src/common'
CC libmbim_common_la-mbim-common.lo
cc1: error: /builder/shared-workdir/build/sdk/staging_dir/target-aarch64_generic_musl/include: No such file or directory [-Werror=missing-include-dirs]
cc1: all warnings being treated as errors
[1] https://github.com/openwrt/packages/issues/10377
[2] https://github.com/openwrt/packages/pull/10378
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Rosen Penev <rosenp@gmail.com>
This fixes commit bae927c551 ("ar71xx: add support for TP-LINK CPE510
V2.0") where the support for this device wasn't optimal.
Device support for the CPE510v2 so far has been a hack to enable
flashing with CPE510v1 images. Those even have different hardware (e.g.
additional ethernet port).
With this patch, we provide proper support for this device in ar71xx.
Installation:
- Flash factory image through stock firmware WEB UI or through TFTP
- To get to TFTP recovery just hold reset button while powering on
for around 4-5 seconds and release.
- Rename factory image to recovery.bin
- Stock TFTP server IP: 192.168.0.100
- Stock device TFTP address: 192.168.0.254
Fixes: bae927c551 ("ar71xx: add support for TP-LINK CPE510 V2.0")
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[Rebased onto revert commit, changed comments in mach-cpe510.c,
changed commit title and description, fixed eth0 MAC address,
removed eth1 initialization]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[squashed revert, added fixes tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch removes scons host build tool, as commit 7087efd72a8d
("scons: move host build tool to a proper place") in the packages feed
has moved scons into the new home.
There are currently no packages in the master tree which would need
scons, yet scons is build always as part of host tools, just in order to
satisfy host build dependency of few packages in the packages feeds.
Ref: https://github.com/openwrt/packages/pull/9584
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This updates the U-Boot which provides the host tools like mkimage to
version 2019.07.
The patches were cleaned up and it was checked if this still compiles
on Linux and FreeBSD.
CONFIG_FIT_SIGNATURE_MAX_SIZE is set to the default value.
The patch for libressl was merged upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This has two improvements over the current version. An autotools fix and
application of the wrt350v2 patch.
Cleaned up Makefile as a result of makefiles being fixed.
Note that this package is not really used as it depends on orion, which is
classified as broken.
This is the last package that uses svn in the tree.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
When libelf from tools/ is used for building the kernel, compilation
aborts due to access to undefined defines since Kbuild adds -Wundef
to the compiler flags.
Patch the header files to use `#if defined(...)` instead of `#if ...`
to prevent such issues.
Ref: https://github.com/NixOS/nixpkgs/issues/59929
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Install the pkg-config definition for libelf in order to allow the
kernel build process discover it later on.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Update CMake to 3.15.1
Refresh patches
Remove inofficial fossies.org and replace with GitHub (link on official site)
Remove 150-C-feature-checks-Match-warnings-more-strictly.patch as it's
a no longer needed backport from upstream.
Disable ccache if GCC is 4.8, 4.9 or 5.X to avoid build failures.
Reference: https://github.com/openwrt/openwrt/pull/1929
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Update make-ext4fs to commit eebda1d55d9701ace2700d7ae461697fadf52d1f
git log --pretty=oneline --abbrev-commit 484903e4..eebda1d5
eebda1d make_ext4: Add strict prototypes.
bb9cf91 make_ext4fs: Remove off64_t in favor of standard off_t
Created with the help of the make-package-update-commit.sh script.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Update e2fsprogs to 1.45.3
Remove OpenBSD patch
Remove Darwin patch, neither macports or brew patches these files
Add patch to avoid crond detection on host OS
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
GNU patch through 2.7.6 is vulnerable to OS shell command injection that
can be exploited by opening a crafted patch file that contains an ed style
diff payload with shell metacharacters. The ed editor does not need to be
present on the vulnerable system. This is different from CVE-2018-1000156.
https://nvd.nist.gov/vuln/detail/CVE-2019-13638
Signed-off-by: Russell Senior <russell@personaltelco.net>
This version bump includes a bunch of fixes and improvements, which
should fix gpsd build breakage in the package feeds.
Ref: https://github.com/SCons/scons/blob/master/src/CHANGES.txt
Signed-off-by: Russell Senior <russell@personaltelco.net>
[added missing commit description]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This seems to be identical to CPE210 v1 despite having removable
antennas.
Specifications:
* SoC: Qualcomm Atheros AR9344 (560 MHz)
* RAM: 64MB
* Storage: 8 MB
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 2x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP:
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is a preparation for ath79 support of the CPE210/CPE510 v1.
Kernel size is chosen equal to the latest update for CPE610 v1.
This also updates the partition size in ar71xx target, so code
remains consistent if someone looks up the device. Since CPE210,
CPE510, WBS210 and WBS510 (all v1) share the same partition
layout definition, and are on deprecated target anyway, this
changes them all at once.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fixes following issue reported by Coverity scan:
*** CID 1452085: Security best practices violations (TOCTOU)
/tools/firmware-utils/src/uimage_padhdr.c: 100 in main()
94
95 if (!infname || !outfname) {
96 usage(argv[0]);
97 exit(1);
98 }
99
>>> CID 1452085: Security best practices violations (TOCTOU)
>>> Calling function "stat" to perform check on "infname".
100 if (stat(infname, &statbuf) < 0) {
Fixes: a1c6a316d2 ("ramips: add support for Fon FON2601")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In GNU patch through 2.7.6, the following of symlinks is mishandled in
certain cases other than input files. This affects inp.c and util.c.
https://nvd.nist.gov/vuln/detail/CVE-2019-13636
Signed-off-by: Russell Senior <russell@personaltelco.net>
Since the switch to Python 3 build fails if CONFIG_USE_MKLIBS is set
("Strip unnecessary functions from libraries" in menuconfig) as
mklibs hasn't been converted to run on Python 3.
* update to most recent upstream version which brings some
reproducibility fixes
* converted to Python 3 using 2to3
* fixed mixed tab/spaces indentation
* fixed use of string.* functions
* some more minor fixes to make Python 3 happy
Fixes commit 19938c8de7 ("build: switch to Python 3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Build tested on ath79 with following packages from packages feed which
build depends on scons. None of them build anymore as it seems, that the
SConscripts are written for Python2.
* packages/net/iotivity (KO, doesn't build even with latest 1.3.1 release)
SyntaxError: invalid syntax
File "/openwrt/build_dir/target-mips_24kc_musl/iotivity-1.2.1/build_common/SConscript", line 40
print "\nError: Current system (%s) isn't supported\n" % host
LookupError: unknown encoding: string_escape:
File "/home/petr/testing/openwrt/build_dir/target-mips_24kc_musl/iotivity-1.3.1/SConstruct", line 28:
SConscript('build_common/SConscript')
* packages/net/smartsnmpd (KO, seems dead, no commit since 2015):
SyntaxError: Missing parentheses in call to 'print'
File "/openwrt/build_dir/target-mips_24kc_musl/smartsnmpd-2014-08-13/SConstruct", line 156
print "Can't find liblua or liblua5.1!"
* packages/utils/gpsd (KO, doesn't build even with latest 3.18.1 release):
AttributeError: 'list' object has no attribute 'keys':
File "/openwrt/build_dir/target-mips_24kc_musl/gpsd-3.18.1/SConstruct", line 1758:
all_manpages = list(base_manpages.keys()) + list(python_manpages.keys())
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Making all in tests
depbase=`echo handshake_table.o | sed 's|[^/]*$|.deps/&|;s|\.o$||'`;\
gcc -DPACKAGE_NAME=\"libressl\" -DPACKAGE_TARNAME=\"libressl\" -DPACKAGE_VERSION=\"2.9.2\" -DPACKAGE_STRING=\"libressl\ 2.9.2\" -DPACKAGE_BUGREPORT=\"\" -DPACKAGE_URL=\"\" -DPACKAGE=\"libressl\" -DVERSION=\"2.9.2\" -DSTDC_HEADERS=1 -DHAVE_SYS_TYPES_H=1 -DHAVE_SYS_STAT_H=1 -DHAVE_STDLIB_H=1 -DHAVE_STRING_H=1 -DHAVE_MEMORY_H=1 -DHAVE_STRINGS_H=1 -DHAVE_INTTYPES_H=1 -DHAVE_STDINT_H=1 -DHAVE_UNISTD_H=1 -DHAVE_DLFCN_H=1 -DLT_OBJDIR=\".libs/\" -DHAVE_SYMLINK=1 -DHAVE_ERR_H=1 -DHAVE_READPASSPHRASE_H=1 -DHAVE_ASPRINTF=1 -DHAVE_MEMMEM=1 -DHAVE_READPASSPHRASE=1 -DHAVE_STRLCAT=1 -DHAVE_STRLCPY=1 -DHAVE_STRNDUP=1 -DHAVE_STRNLEN=1 -DHAVE_STRSEP=1 -DHAVE_TIMEGM=1 -DHAVE_GETPROGNAME=1 -DHAVE_SYSLOG=1 -DHAVE_POLL=1 -DHAVE_SOCKETPAIR=1 -DHAVE_ARC4RANDOM=1 -DHAVE_ARC4RANDOM_BUF=1 -DHAVE_ARC4RANDOM_UNIFORM=1 -DHAVE_TIMINGSAFE_BCMP=1 -DHAVE_CLOCK_GETTIME=1 -DHAVE_VA_COPY=1 -DHAVE___VA_COPY=1 -DSIZEOF_TIME_T=8 -I. -I../include -I../include/compat -DLIBRESSL_INTERNAL -D__BEGIN_HIDDEN_DECLS= -D__END_HIDDEN_DECLS= -I ../crypto/modes -I ../crypto/asn1 -I ../ssl -I ../tls -I ../apps/openssl -I ../apps/openssl/compat -D_PATH_SSL_CA_FILE=\"../apps/openssl/cert.pem\" -I/Users/kevin/wrt/staging_dir/host/include -D__STRICT_ALIGNMENT -O2 -I/Users/kevin/wrt/staging_dir/host/include -fpic -Wall -std=gnu99 -fno-strict-aliasing -fno-strict-overflow -D_FORTIFY_SOURCE=2 -fstack-protector-strong -Qunused-arguments -Wno-pointer-sign -MT handshake_table.o -MD -MP -MF $depbase.Tpo -c -o handshake_table.o handshake_table.c &&\
mv -f $depbase.Tpo $depbase.Po
make[4]: *** No rule to make target `/Users/kevin/wrt/build_dir/host/libressl-2.9.2/crypto/.libs/libcrypto_la-cpuid-macosx-x86_64.o', needed by `handshake_table'. Stop.
make[3]: *** [all-recursive] Error 1
A similar error & clues from
e783d60473
"
LibreSSL 2.9.1 now has a test that requires libtls.a, however, when building a
shared library only build, the --disable-static flag is passed to libressl,
which prevents the building of libtls.a.
With libtls.a not being built, the following error occurs:
libressl-2.9.1/tls/.libs/libtls.a', needed by 'handshake_table'. Stop.
There are three options to fix this:
1) Stick with autotools, and provide a patch that removes building anything in
the tests folder.
2) Pass --enable-static to LIBRESSL_CONF_OPTS
3) Change the package type to cmake, as a cmake build does not have this issue."
It appears we cannot change to cmake because cmake has a dependency on
an ssl library.
Take option 1 and do not build the tests.
Also take the opportunity to remove man page building as well.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Fixes following errors:
src/mkfwimage.c:279:8: error: format specifies type 'long' but the argument has type 'off_t' (aka 'long long') [-Werror,-Wformat]
d->stats.st_size,
^~~~~~~~~~~~~~~~
src/mkfwimage.c:280:8: error: format specifies type 'long' but the argument has type 'long long' [-Werror,-Wformat]
d->partition_length - d->stats.st_size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
src/mkfwimage.c:378:6: error: format specifies type 'unsigned long' but the argument has type 'long long' [-Werror,-Wformat]
d->stats.st_size - d->partition_length);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Reported-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
src/mkfwimage.c:276:8: error: format '%lld' expects argument of type 'long long int', but argument 4 has type '__off_t' {aka 'const long int'} [-Werror=format=]
src/fw.h:71:36: error: format '%llu' expects argument of type 'long long unsigned int', but argument 6 has type '__off_t' {aka 'long int'} [-Werror=format=]
inlined from 'main' at src/mkfwimage.c:543:12:
/string_fortified.h:106:10: error: '__builtin_strncpy' output truncated before terminating nul copying 4 bytes from a string of the same length [-Werror=stringop-truncation]
inlined from 'write_part' at src/mkfwimage.c:235:2,
string_fortified.h:106:10: error: '__builtin_strncpy' specified bound 16 equals destination size [-Werror=stringop-truncation]
inlined from 'main' at src/mkfwimage.c:477:5:
string_fortified.h:106:10: error: '__builtin_strncpy' specified bound 256 equals destination size [-Werror=stringop-truncation]
inlined from 'main' at src/mkfwimage.c:496:5:
string_fortified.h:106:10: error: '__builtin_strncpy' specified bound 4096 equals destination size [-Werror=stringop-truncation]
inlined from 'main' at src/mkfwimage.c:481:5:
string_fortified.h:106:10: error: '__builtin_strncpy' specified bound 4096 equals destination size [-Werror=stringop-truncation]
inlined from 'main' at src/mkfwimage.c:485:5:
string_fortified.h:106:10: error: '__builtin_strncpy' specified bound 16 equals destination size [-Werror=stringop-truncation]
Runtested on ath79 and UBNT Bullet M XW.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fix 4 errors reported by gcc 9
3 mismatched format type errors
1 unused variable error
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
While looking at the ath25 build breakage of 19.07 images today I've
encountered following error:
mkfwimage -B XS5 -v [...] ath25-ubnt5-squashfs-sysupgrade.bin.new
ERROR: Failed creating firmware layout description - error code: -2
Which is barely human readable and needs poking into the source code, so
this patch makes the error more verbose and usable by mere mortals.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Let's enforce additional automatic checks enforced by the compiler in
order to catch possible errors during compilation.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
TP-Link CPE510-v2/v3 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
- Based on the same underlying hardware as the TP-Link CPE510
- Power, LAN, and 4 green LEDs
- 1 10/100Mbps Shielded Ethernet Port (Passive PoE in)
- Built-in 13dBi 2x2 dual-polarized directional MIMO antenna
- Adjustable transmission power from 0 to 23dBm/200mw
Flashing instructions:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[whitespace fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
TP-Link RE650 v1 is a dual-band AC2600 range extender,
based on MediaTek MT7621A and MT7615E. According to the
wikidevi entry for RE650 this device is identical with
TP-Link RE500 as hardware. This patch supports only RE650.
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 16 MB - Winbond 25Q128FVSG
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART header (J1) - 2:GND, 3:RX, 4:TX
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
Unfortunately, I can't find an easy way to recover the RE
without opening the device and using modified binaries. The
TFTP upload will only work if selected from u-boot, which
means you have to open the device and attach to the serial
console. The TFTP update procedure does *not* accept the
published vendor firmware binaries. However, it allows to
flash kernel + rootfs binaries, and this works if you have
a backup of the original contents of the flash. It's probably
possible to create special image out of the vendor binaries
and use that as recovery image.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
[re-added variables for kernel header]
Signed-off-by: David Bauer <mail@david-bauer.net>
