Commit Graph

27043 Commits

Author SHA1 Message Date
Chen Minqiang
18bea173a6 mediatek: add alternative stock layout for Xiaomi Redmi Router AX6000
In this implementation, the flash partition layout is adjusted to avoid
modifying the uboot environment of mtdparts. This ensures that the 30M
ubi_kernel partition remains aligned with the stock ubi partition, and
the kernel volume is placed in it. This allows the stock uboot to boot
from it without changing the mtdparts, which is useful for reverting back
to the stock firmware using Xiaomi Firmware Tools. In actual testing,
modifying mtdparts has been found to break Xiaomi Firmware Tools.

1. use ARTIFACTS to generate initramfs-factory.ubi for easy installation.
2. The NAND flash layout is changed to allow for reverting back to the
   stock firmware.
3. Before performing sysupgrade, do some cleanup in platform_pre_upgrade
   to ensure a clean installation of OpenWRT.
4. Setup the uboot env to ensure that the system always boot, which can
   be helpful for users who may forget to do this before sysupgrade in
   the initramfs.

New flash instructions:
1. Gain ssh access. Please refer to:
   https://openwrt.org/toh/xiaomi/redmi_ax6000#installation)

2. Check which system current u-boot is loading from:
   COMMAND: `cat /proc/cmdline`
   sample OUTPUT: `console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1`
   if firmware=1, current system is ubi1
   if firmware=0, current system is ubi0

3. Setup nvram and write the firmware:
   If the current system is ubi1, please set it up so that the next time
   it will boot from ubi, and write the firmware to ubi:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd8 -y -f /tmp/initramfs-factory.ubi
```
   If the current system is ubi, please set it up so that the next time
   it will boot from ubi1, and write the firmware to ubi1:
```
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
ubiformat /dev/mtd9 -y -f /tmp/initramfs-factory.ubi
```

4. After rebooting, the system should now boot into the openwrt initramfs.
   Flash the squashfs-sysupgrade.bin via using ssh or luci.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```
Done.

For existing users of the Redmi AX6000 running OpenWrt, here are the steps to
switch to this new layout:

1. Flash initramfs-factory.ubi
```
mtd -r -e ubi write /tmp/initramfs-factory.ubi ubi
```

2. After rebooting, the system will boot into the new openwrt-initramfs.
Log in and perform a sysupgrade to complete the process.
```
sysupgrade -n /tmp/squashfs-sysupgrade.bin
```

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-17 15:04:16 +08:00
Christian Marangi
d7876daf65
generic: add support for EON EN25QX128A spi nor flash
Add support for EON EN25QX128A spi nor flash with no flags as it does
support SFDP parsing.

Fixes: #9442
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Tested-by: Szabolcs Hubai <szab.hu@gmail.com> [ramips/mt7621: xiaomi_mi-router-4a-gigabit]
2022-12-16 20:58:36 +01:00
Furong Xu
d9e1362581 mediatek: add LED support for Xiaomi Redmi AX6000
add DT nodes and default package for the LEDs on Redmi AX6000

Signed-off-by: Furong Xu <xfr@outlook.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-16 21:42:02 +08:00
Furong Xu
335c1e7cfd mediatek: enable sel_clk for spi-mt65xx
Without explicitly enabling sel_clk, clk_disable_unused() will disable
it when boot is done, causing CPU hang on SPI1 register access on MT7986.
Explicitly enable sel_clk to make SPI1 functional.

Signed-off-by: Furong Xu <xfr@outlook.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2022-12-16 21:42:02 +08:00
INAGAKI Hiroshi
88db7461cf realtek: add Linux Kernel 5.15 as testing version
Add Linux Kernel 5.15 support for testing.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[APRESIA ApresiaLightGS120GT-SS, Panasonic Switch-M24eG PN28240K, Switch-M48eG PN28480K]
Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com>
TP-Link TL-SG2008P
Tested-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[D-Link DGS-1210-20, DGS-1210-52, Zyxel XGS1010-12]
Tested-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[Zyxel XGS1250-12]
Tested-by: Lucian Cristian <lucian.cristian@gmail.com> # Zyxel
[HPE 1920-8G, 1920-48G]
Tested-by: Jan Hoffmann <jan@3e8.eu>
2022-12-15 20:54:12 +01:00
INAGAKI Hiroshi
69055a5412 realtek: enable needs_standalone_vlan_filtering on DSA driver in 5.15
To configure VLAN 0, enable needs_standalone_vlan_filtering option
of dsa_switch struct.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-12-15 20:54:03 +01:00
INAGAKI Hiroshi
109962d8bf realtek: update dsa.c of DSA driver for 5.15
- rtl83xx_vlan_filtering()

  "struct switchdev_trans *trans" parameter was removed[1] and
  "struct netlink_ext_ack *extack" was added[2].

[1]: https://www.spinics.net/lists/netdev/msg712250.html
[2]: https://www.spinics.net/lists/netdev/msg722496.html

- rtl83xx_vlan_add/del()

  vlan->vid_begin and vlan->vid_end were removed and vlan->vid was
  added[3].

[3]: https://www.spinics.net/lists/netdev/msg712248.html

- rtl83xx_vlan_prepare()

  "port_vlan_prepare" member was removed from "dsa_switch_ops" struct
  in dsa.h[4] and vlan_prepare function should be called from vlan_add
  function. Also, change return type of vlan_add function to int.

[4]: https://www.spinics.net/lists/netdev/msg712252.html

- rtl83xx_port_mdb_add()

  "port_mdb_prepare" member in "dsa_switch_ops" struct was removed and
  preparation need to be done in the function of "port_mdb_add" member
  instead. And also, int type need to be returned on "port_mdb_add"
  member[5].

[5]: https://www.spinics.net/lists/netdev/msg712251.html

- rtl83xx_port_pre_bridge_flags(), rtl83xx_port_bridge_flags()

  The current "port_pre_bridge_flags" member and "port_bridge_flags"
  member in "dsa_switch_ops" in dsa.h has flags of
  "struct switchdev_brport_flags" type instead[6], so adjust to it.
  And, the changed features are passed by flags.mask[7] in
  rtl83xx_port_bridge_flags(), so check it before calling function
  to enable/disable fieature.

[6]: https://lore.kernel.org/lkml/20210212151600.3357121-7-olteanv@gmail.com/
[7]: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e18f4c18ab5b0dd47caaf8377c2e36d66f632a8c

Suggested-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[shorten final return statement of rtl83xx_port_mdb_add()]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-12-15 20:52:40 +01:00
INAGAKI Hiroshi
1f153558a3 realtek: update platform support for 5.15
- fw_passed_dtb and others were replaced to get_fdt() function[1]
- __appended_dtb defined by asm/bootinfo.h[2]

[1]: https://www.spinics.net/lists/linux-mips/msg03332.html
[2]: https://www.spinics.net/lists/linux-mips/msg03332.html

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-12-15 20:52:40 +01:00
INAGAKI Hiroshi
f3a9975549 realtek: refresh config-5.15 in all subtargets
Refresh config-5.15 in all subtargets by kernel_menuconfig.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-12-15 20:52:40 +01:00
INAGAKI Hiroshi
aa528eec73 realtek: refresh patches in 5.15
Adjust patches for kernel 5.15.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-12-15 20:52:40 +01:00
INAGAKI Hiroshi
23881c91e5 realtek: drop patches of upstreamed fix and changes from 5.15
- 007-5.16-gpio-realtek...: upstreamed on 5.16 and backported to 5.15.3
- 708-brflood-spi.patch   : upstreamed
- 709-lag-offloading.patch: upstreamed
- 713-v5.12-net-dsa-...   : upstreamed and some implementations are
                            replaced

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-12-15 20:52:40 +01:00
INAGAKI Hiroshi
a9d5a8bc79 realtek: drop patches of upstreamed drivers from 5.15
The following drivers were upstreamed and available on 5.15, so drop
from OpenWrt tree.

- realtek-otto-gpio (5.13)
- realtek-rtl-spi (5.12)
- realtek-rtl-intc (5.12)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2022-12-15 20:52:40 +01:00
INAGAKI Hiroshi
8fb15ea52a realtek: copy dts/files/patches/configs for 5.15
Copy dts/files/patches/configs from 5.10 to 5.15.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[refresh with updated DGS-1210 dts files]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2022-12-15 20:52:09 +01:00
Christian Lamparter
d8da5002a2 ath79: fix dtc warnings in ruckus zf7372
|:69.4-14: Warning (reg_format): beamforming-2g-gpio@0:reg: property has invalid length (4 bytes)
|:85.4-14: Warning (reg_format): beamforming-5g-gpio@0:reg: property has invalid length (4 bytes)

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-15 15:45:47 +01:00
Christian Lamparter
0dacf14495 ath79: fix dtc warnings in eap1750h
|109.3-19: Warning (reg_format): macaddr@0:reg:property has invalid length (8 bytes)
|113.3-24: Warning (reg_format): calibration@1000:reg: property has invalid length (8 bytes)
|117.3-24: Warning (reg_format): calibration@5000:reg: property has invalid length (8 bytes)

also integrate the art-nodes nodes back into the partition-subnode
and change the calibration labels to match what everyone else is
doing.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-15 15:45:47 +01:00
Christian Lamparter
0f227720f9 ath79: fix dtc warnings in eap1200h
|109.3-19: Warning (reg_format): macaddr@0:reg:property has invalid length (8 bytes)
|113.3-24: Warning (reg_format): calibration@1000:reg: property has invalid length (8 bytes)
|117.3-24: Warning (reg_format): calibration@5000:reg: property has invalid length (8 bytes)

also integrate the art-nodes nodes back into the partition-subnode
and change the calibration labels to match what everyone else is
doing.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-15 15:45:47 +01:00
Nick Hainke
4146701469 ath79: replace reference to legacy qca,disable-2ghz in WatchGuard AP100
Commit 4c8dd973ef ("ath9k: OF: qca,disable-(2|5)ghz => ieee80211-freq-limit")
removed "qca,disable-5ghz" and "qca,disable-2ghz".

Signed-off-by: Nick Hainke <vincent@systemli.org>
(converted patch to remove the ieee80211-freq-limit property instead)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-15 15:45:47 +01:00
Nick Hainke
ae5cb164cd ath79: switch to upstream ieee80211-freq-limit for Araknis AN-300-AP-I-N
Commit 4c8dd973ef ("ath9k: OF: qca,disable-(2|5)ghz => ieee80211-freq-limit")
removed "qca,disable-5ghz" and "qca,disable-2ghz". Switch to upstream
ieee80211-freq-limit.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-15 15:45:47 +01:00
Nick Hainke
08c114ee16 ath79: convert Winchannel WB2000 WiFis to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

Signed-off-by: Nick Hainke <vincent@systemli.org>
(removed mtd-cal-data property, merged art + addr nodes back into
partition)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-15 15:45:47 +01:00
Nick Hainke
fd456106aa ath79: convert Ubiquiti UniFi AP Pro WiFis to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

Signed-off-by: Nick Hainke <vincent@systemli.org>
(merged art node back into partition-node)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-15 15:45:47 +01:00
Nick Hainke
f63cf33aa7 ath79: convert OCEDO Raccoon WiFis to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

Signed-off-by: Nick Hainke <vincent@systemli.org>
(merged art into partition node, removed stale uboot label)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-15 15:45:47 +01:00
Nick Hainke
783936c1f7 ath79: Mercury MW4530R v1 already uses nvmem-cells
Remove the caldata extraction in userspace. The board already uses
nvmem-cells since
commit e354b01baf ("ath79: calibrate all ar9344 tl-WDRxxxx with nvmem")

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-15 15:45:35 +01:00
Nick Hainke
4845b60525 ath79: convert boards based on senao_ap-dual.dtsi WiFis to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-15 15:08:09 +01:00
Nick Hainke
21495c92dc ath79: convert Atheros DB120 WiFis to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

Signed-off-by: Nick Hainke <vincent@systemli.org>
(merged art-node back into partition-node)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-15 15:08:09 +01:00
Nick Hainke
1b125aabf4 ath79: convert Araknis AN-300-AP-I-N WiFis to nvmem-cells
Pull the calibration data from the nvmem subsystem. This allows us to
move userspace caldata extraction into the device-tree definition.

Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-12-15 15:08:08 +01:00
Johannes Heimansberg
708ea56fb9 bcm27xx: bcm2711: add kmod-r8169
Some carrier boards [1][2] for the Raspberry Pi CM4 that are specifically
designed to be used as routers come with secondary NICs using a Realtek
RTL8111 Gigabit Ethernet chip.

When using such a board as a router with OpenWrt, it is very helpful
when both NICs are working by default. Since the Raspberry Pi 4 and the
CM4 have plenty of disk space, it should cause no harm to include the
kmod-r8169.

[1] https://wiki.dfrobot.com/Compute_Module_4_IoT_Router_Board_Mini_SKU_DFR0767
[2] https://www.waveshare.com/wiki/CM4-DUAL-ETH-MINI

Signed-off-by: Johannes Heimansberg <git@jhe.dedyn.io>
(r8169 should pull in the necessary dependencies.)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-15 15:08:08 +01:00
Linus Walleij
1bef8d62d4 bcm53xx: Patch to support BCMA rev 11
A backported patch to the BCMA driver necessary to support the
DWL-8610AP and DIR-890L. Patch will be in upstream v6.2.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-12-15 15:08:08 +01:00
John Audia
90120a1552 kernel: bump 5.10 to 5.10.159
Removed upstreamed:
	backport-5.10/888-v6.1-ca8210-Fix-crash-by-zero-initializing-data.patch[1]

All patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.159&id=0a8e66e375736ea12c11f0ef238ba2a8efec460b

Build system: x86_64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-14 23:37:28 +01:00
John Audia
b6fa423907 kernel: bump 5.15 to 5.15.83
Removed upstreamed:
	backport-5.15/883-v6.1-ca8210-Fix-crash-by-zero-initializing-data.patch[1]

All patches automatically rebased

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.83&id=246bcd05ba6cc43b34ac0bb4bac3ea94a4efa07c

Build system: x86_64
Build-tested: bcm2711/RPi4B
Run-tested: bcm2711/RPi4B

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-14 23:34:50 +01:00
Stijn Tintel
b3dd15ca0a kernel: add missing symbol to 5.10 config
Kernel 5.10.158 added a prompt for the FUNCTION_ERROR_INJECTION symbol.
This is exposed in builds with CONFIG_KERNEL_KPROBES enabled, causing
those builds to fail due to a missing symbol. Add the symbol to fix
this.

Fixes: 6801c460b6 ("kernel: bump 5.10 to 5.10.158")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-12-14 20:29:36 +02:00
Stijn Tintel
f9bd655f16 kernel: add missing symbol to 5.15 config
Kernel 5.15.82 added a prompt for the FUNCTION_ERROR_INJECTION symbol.
This is exposed in builds with CONFIG_KERNEL_KPROBES enabled, causing
those builds to fail due to a missing symbol. Add the symbol to fix
this.

Fixes: 68426e54ed ("kernel: bump 5.15 to 5.15.82")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-12-14 19:12:33 +02:00
Stijn Tintel
230f2fccd1 qoriq: switch to kernel 5.15
The testing kernel has been running fine for months on a rather complex
network setup, with one exception being a crash in
__xfrm_state_delete(). This crash has been fixed in kernel 5.15.82, so
let's switch the qoriq target to kernel 5.15 by default.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-12-14 18:53:39 +02:00
Christian Marangi
823ddab80e
ipq806x: 5.15: standardize wpq864 partition table
Compex WPQ864 contains a non standard partition table. Each partition
node should be named partition and should contain a valid reg.
Fix an extra "-" present after the reg for SBL2_1 partition.

Also add "0:" to each qcom default partition following smem naming.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-14 02:23:22 +01:00
Christian Marangi
266b261d39
ipq806x: 5.15: fix wrong boot-partitions values for split partitions
The refreshed patch actually use the format of <start size start size>
instead of <start end start end>. This cause boot fail since the rootfs
can't be mounted with these wrong values.

Fix it to the correct format in each affected dts.

Fixes: #11498
Fixes: 6134ba4a34 ("ipq806x: 5.15: add boot-partitions binding to fix block warning")
Tested-by: Matt Buczko <mbuczko@hotmail.com> # Askey RT4230W
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-14 02:23:22 +01:00
Andrew Cameron
550e5b2184 ath79: add support for TP-Link CPE605-v1
TP-Link CPE605-v1 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344

Specifications:
 - 560/450/225 MHz (CPU/DDR/AHB)
 - 1x 10/100 Mbps Ethernet
 - 64 MB of DDR2 RAM
 - 8 MB of SPI-NOR Flash
 - 23dBi high-gain directional antenna and a dedicated metal reflector
 - Power, LAN, WLAN5G green LEDs
 - 3x green RSSI LEDs

Flashing instructions:
 Flash factory image through stock firmware WEB UI or through TFTP
 To get to TFTP recovery just hold reset button while powering on for
 around 4-5 seconds and release.
 Rename factory image to recovery.bin
 Stock TFTP server IP:192.168.0.100
 Stock device TFTP adress:192.168.0.254

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
2022-12-13 23:17:27 +01:00
Mikhail Zhilkin
0ec8d991c2 ramips: add support for Etisalat S3
Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company.

Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB
Flash: 128 MiB
Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2
Wireless 5 GHz (MT7615E): a/n/ac, 4x4
Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4)
USB ports: 1x USB3.0
Button: 2 buttons (Reset & WPS)
LEDs:
   - 1x Status (RGB)
   - 1x 2.4G (blue, hardware, mt76-phy0)
   - 1x 5G (blue, hardware, mt76-phy1)
Power: 12 VDC, 1.5 A
Connector type: barrel
Bootloader: U-Boot

Installation
-----------------
1.  Login to the router web interface under admin account
2.  Navigate to Settings -> Configuration -> Save to Computer
3.  Decode the configuration. For example, using cfgtool.py tool (see
    related section):
       cfgtool.py -u configurationBackup.cfg
4.  Open configurationBackup.xml and find the following line:
    <PARAMETER name="Password" type="string" value="<your router serial \
       is here>" writable="1" encryption="1" password="1"/>
5.  Insert the following line after and save:
<PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/>
6.  Encode the configuration. For example, using cfgtool.py tool:
       cfgtool.py -p configurationBackup.xml
7.  Upload the changed configuration (configurationBackup_changed.cfg) to
    the router
8.  Login to the router web interface (SuperUser:ETxxxxxxxxxx, where
    ETxxxxxxxxxx is the serial number from the backplate label)
9.  Navigate to Settings -> WAN -> Add static IP interface (e.g.
    10.0.0.1/255.255.255.0)
10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22,
    10.0.0.0/255.255.255.0 and interface created before
11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the
    ethernet cable to the WAN port of the router
12. Connect to the router using SSH shell under SuperUser account
13. Run in SSH shell:
       sh
14. Make a mtd backup (optional, see related section)
15. Change bootflag to Sercomm1 and reboot:
       printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
       reboot
16. Login to the router web interface under admin account
17. Remove dots from the OpenWrt factory image filename
18. Update firmware via web using OpenWrt factory image

Revert to stock
---------------
Change bootflag to Sercomm1 in OpenWrt CLI and then reboot:
   printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3

mtd backup
----------
1. Set up a tftp server (e.g. tftpd64 for windows)
2. Connect to a router using SSH shell and run the following commands:
      cd /tmp
      for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
      tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
      tftp -l mtd.md5 -p 10.0.0.2

Recovery
--------
Use sercomm-recovery tool.
Link: https://github.com/danitool/sercomm-recovery

MAC Addresses
-------------
+-----+------------+---------+
| use | address    | example |
+-----+------------+---------+
| LAN | label      | *:50    |
| WAN | label + 11 | *:5b    |
| 2g  | label + 2  | *:52    |
| 5g  | label + 3  | *:53    |
+-----+------------+---------+
The label MAC address was found in Factory 0x21000

cfgtool.py
----------
A tool for decoding and encoding Sercomm configs.
Link: https://github.com/r3d5ky/sercomm_cfg_unpacker

Co-authored-by: Karim Dehouche <karimdplay@gmail.com>
Co-authored-by: Maximilian Weinmann <x1@disroot.org>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
2022-12-13 23:06:20 +01:00
Christian Marangi
05dbdcbd32
generic: move pending 870 ca8210 fix crash patch to backport
Patch got merged upstream in kernel 6.1. Move it to backport to better
track it.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-13 02:05:29 +01:00
Christian Marangi
c3c9ef598c
generic: fix wrong PTR_ERR use in of net mac address ascii patch
nvmem_cell_read return a pointer error when an error occurs. Currently
we convert the pointer error to an int while the rest of the function
return a void* and expcet an error pointer. Fix this PTR_ERR msuse
fixing compilation warning.

Fixes the following compilation warning:
net/ethernet/eth.c: In function 'nvmem_cell_get_mac_address':
net/ethernet/eth.c:547:24: warning: returning 'long int' from a function with return type 'void *' makes pointer from integer without a cast [-Wint-conversion]
  547 |                 return PTR_ERR(mac);
      |                        ^~~~~~~~~~~~
net/ethernet/eth.c: In function 'nvmem_cell_get_mac_address_ascii':
net/ethernet/eth.c:564:24: warning: returning 'long int' from a function with return type 'void *' makes pointer from integer without a cast [-Wint-conversion]
  564 |                 return PTR_ERR(mac_ascii);
      |                        ^~~~~~~~~~~~~~~~~~

Fixes: 7b863af180 ("kernel: move mac-address-ascii patches to generic")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-12-13 00:33:19 +01:00
Linus Walleij
772434e707 gemini: Set proper default networks
Some Gemini devices are NAS type devices and need to ask for
DHCP IP on eth0. Some has a LAN/WAN setup. Add sensible
defaults for all known devices.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-12-12 11:18:02 +01:00
Christian Lamparter
50d20db6a8 uml: switch to Kernel 5.15
Switch over from testing version.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-12 09:06:17 +01:00
Christian Lamparter
f6c61571fb bcm53xx: remove MR32's openwrt specific patch for LEDs
The patch managed to sneak into v5.15 whereas it was
properly deleted for v5.10.

Fixes: 8f6e2bb178 ("bcm53xx: remove MR32's specific get_leds_dt code")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-12 09:06:17 +01:00
Chukun Pan
b40a047f1f sunxi: fix sunxi-ir kconfig and description
Removed a20 in description, since it
only works for a10, a13 and a31.
Also refreshed kernel config.

Fixes: #10466
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(moved fixes, refreshed, added CONFIG_DVB_USB=n)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-12 09:06:17 +01:00
Chukun Pan
a125d46a28 sunxi: modules: remove useless AddDepends/rtc
AddDepends/rtc has been removed in commit 3da7fe6, same here.
Fixes: 3da7fe6 ("kernel: remove useless AddDepends/rtc abstraction")

Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(RTC_SUPPORT - though this is implied by the TARGET_sunxi)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-12-12 09:06:17 +01:00
Tony Butler
1e240f60a5 kernel: modules/lib-lz4: add lz4hc_compress
enable option `CONFIG_CRYPTO_LZ4HC` to match default kernel config

this only adds the `lz4hc_compress` module, and has no effect on the
`lz4_decompress` module which already supports any flavor

Signed-off-by: Tony Butler <spudz76@gmail.com>
2022-12-11 09:32:53 -08:00
Tony Butler
9a1ab8aa03 lantiq: vr9: include usb driver for fritz 7430
Reported by user: missing driver for USB; add to image definition
https://github.com/openwrt/openwrt/issues/11326

Resolves: #11326

Signed-off-by: Tony Butler <spudz76@gmail.com>
Acked-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-12-11 16:46:34 +01:00
Hauke Mehrtens
2484f0951c kernel: Refresh kernel 5.10
Make the patches apply cleanly again.

Fixes: 8327e0fb72 ("kernel: backport the dev_set_threaded export to 5.10")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-12-11 16:42:16 +01:00
Weiping Yang
1c169d28ff ipq40xx: fix usb driver not loaded for GL-A1300
This patch enables USB support for the GL.iNet GL-A1300
Repair the usb driver startup phase is not loaded

Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
2022-12-11 03:06:54 +01:00
John Audia
6801c460b6 kernel: bump 5.10 to 5.10.158
All patches automatically rebased.

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-11 02:43:28 +01:00
John Audia
7b7d8fe60d kernel: bump 5.10 to 5.10.157
Manually rebased:
	backport-5.10/610-v5.13-32-net-ethernet-mtk_eth_soc-add-support-for-initializin.patch
	hack-5.10/645-netfilter-connmark-introduce-set-dscpmark.patch

Removed upstreamed:
	pending-5.10/706-netfilter-nf_flow_table-add-missing-locking.patch[1]

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.157&id=b8e494240e69f91517256adcd6fda62d0671772d

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-11 02:43:28 +01:00
John Audia
f83a8329a3 kernel: add symbol in generic config for 5.10.157
Add CONFIG_INET_TABLE_PERTURB_ORDER=16 to generic config

Signed-off-by: John Audia <therealgraysky@proton.me>
2022-12-11 02:43:28 +01:00