Manually rebased:
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
All patches automatically rebased.
Signed-off-by: John Audia <therealgraysky@proton.me>
[Move gro_skip in 680-NET-skip-GRO-for-foreign-MAC-addresses.patch to old position]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128 MB
RAM: K4A4G165WF-BCWE 512 MB
Ethernet: 4x 10/100/1000 Mbps
WiFi1: MT7976GN 2.4GHz ax 4x4
WiFi2: MT7976AN 5GHz ax 4x4
Button: Mesh, Reset
Flash instructions:
1. Gain ssh and serial port access, see the link below:
https://openwrt.org/toh/xiaomi/redmi_ax6000#installation
2. Use ssh or serial port to log in to the router, and
execute the following command:
nvram set boot_wait=on
nvram set flag_boot_rootfs=0
nvram set flag_boot_success=1
nvram set flag_last_success=1
nvram set flag_try_sys1_failed=8
nvram set flag_try_sys2_failed=8
nvram commit
3. Set a static ip on the ethernet interface of your computer
(e.g. default: ip 192.168.31.100, gateway 192.168.31.1)
4. Download the initramfs image, rename it to initramfs.bin,
and host it with the tftp server.
5. Interrupt U-Boot and run these commands:
setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi)
saveenv
tftpboot initramfs.bin
bootm
6. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Revert to stock firmware:
Restore mtdparts back to default, then use the
vendor's recovery tool (Windows only).
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
When firmware images only contained compressed kernels and squashfs roots,
uncompressed tar files were a good option. We are now using UBIFS images,
both raw and tarred, as well as ubinized (full UBI partition) images, all
of which benefit greatly from compression.
For example, a raw ubinized backup taken from a running Askey RT4230W REV6
(such full backups can be restored via the LUCI's sysupgrade UI) is over
400 MB, but compresses to less than 10 MB.
This commit adds support for gzipped versions of all file types already
accepted by the nand sysupgrade mechanism, be them raw or tarred.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
It has been reported that ubinized nand sysupgrade fails under certain
circumstances, being unable to detach the existing ubi partition due to
volumes within the partition being mounted.
This is an attempt to solve such issues by unmounting and removing
ubiblock devices and unmounting ubi volumes within the target partition
prior to detaching and formatting it.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
- Never return from 'nand_do_upgrade', not even in case of errors, as that
would cause execution of sysupgrade code not intended for NAND devices.
- Unify handling of sysupgrade success and failure.
- Detect and report more error conditions.
- Fix outdated/incorrect/unclear comments.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
In rtl83xx_set_features we set bit 3 to enable, and bit 4 to disable
checksuming. Looking at rtl93xx_set_features we however see that for
both enable and disable the same bit is used (bit 4). This can't be
right, especially as bit 4 for rtl83xx seems to be Collision threshold
occupying 2 bits. Change this to make this more logical.
Fixes: 9e8d62e421 ("realtek: enable CRC offloading")
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Linksys EA8500 is currently broken after the kernel 5.15 bump. Disable
compiling it by default from buildbot to prevent brick from the user.
Don't mark it as BROKEN to permit user to compile images and permit devs
to bisect the problem with the users.
The current problem with the device is that the switch is not detected
and we can't comunicate with it via MDIO.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Linksys EA8500 is currently broken after the kernel 5.15 bump. Disable
compiling it by default from buildbot to prevent brick from the user.
Don't mark it as BROKEN to permit user to compile images and permit devs
to bisect the problem with the users.
The current problem with the device is that the switch is not detected
and we can't comunicate with it via MDIO.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
L2 learning on the CPU port is currently not consistently configured and
relies on the default configuration of the device. On RTL83xx, it is
disabled for packets transmitted with a TX header, as hardware learning
corrupts the forwarding table otherwise. As a result, unneeded flooding
of traffic for the CPU port can already happen on some devices now. It
is also likely that similar issues exist on RTL93xx, which doesn't have
a field to disable learning in the TX header.
To address this, disable hardware learning for the CPU port globally on
all devices. Instead, enable assisted learning to let DSA write FDB
entries to the switch.
For now, this does not sync local/bridge entries to the switch. However,
support for that was added in Linux 5.14, so the next switch to a newer
kernel version is going to fix this.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Initialize the data structure using memset to avoid the possibility of
writing garbage values to the hardware.
Always set a valid entry type, which should fix writing unicast entries
on RTL930x.
For unicast entries, set the is_static flag to prevent the switch from
aging them out.
Also set the rvid field for unicast entries. This is not strictly
necessary, as the switch fills it in automatically from a non-zero vid.
However, this makes the code consistent with multicast entry setup.
While at it, reorder the statements and fix some style issues (double
space, comma instead of semicolon at end of statement). Also remove the
unneeded priv parameter and debug print for the multicast entry setup
function.
Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Commit e8b5429609 included an unintended change and we now call
scan_wifi before a network reload.
Restore the original behaviour and call scan_wifi only after a network
reload.
Fixes: e8b5429609 ("base-files: wifi: tidy up the reconf code")
Signed-off-by: Bob Cantor <bobc@confidesk.com>
Commit b82cc80713 included an unintended change and we now call
scan_wifi before a network reload.
Restore the original behaviour and call scan_wifi only after a network
reload.
Fixes: b82cc80713 ("base-files: wifi: swap the order of some ubus calls")
Signed-off-by: Bob Cantor <bobc@confidesk.com>
This patch was wrongly dropped with the assumption that it was moved to
generic. This wasn't the case and caused the malfunction of the Asrock
G10 router.
Reintroduce it to fix Asrock G10 functionality.
Fixes: 8cc2caed58 ("ipq806x: 5:15: add testing kernel version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Zyxel NGB6817 is the only router that use mmc for rootfs. Upstream
kernel dtsi have mmc-ddr-1_8v enabled for sddc1. This is wrong as mmc on
ipq806x is supplied by a fixed 3.3v regulator and can't operate at 1.8v.
This cause the sddc1 to malfunction and cause kernel panic.
In old 5.15 version this was disabled but it was put in addition to many
other changes so it was dropped silently. Restore this patch to fix
working condition of such router.
Fixes: 88bf652 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Fixes: #11000
Tested-by: Hendrik Koerner <koerhen@web.de>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In refreshing DTS to the upstream version an unwanted change slipped in
the commit. The ASRock G10 dts got converted to DSA without any support.
Revert this to swconfig driver to restore normal functionality.
Fixes: 88bf652525 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
We currently ignore ret of the nandc partition parser if unprotected
spare data is true. This is the case for ipq806x nand.
Backport patch that fix this error and correctly handle error from
partition parser.
Fixes: ae6a63bc97 ("ipq806x: 5.15: replace nandc patch with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport patch from kernel 5.15 that mute error on EPROBE_DEFER with
smempart parser.
This parser require the smem device to be probed first and currently it
may happen that mtd gets probed before the smem device causing an error
on the smempart parser. This error may be confusing and should be muted.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In new kernel version from 5.16, smem node can be declared directly in
the reserved-space node. Upstream ipq806x (and to-be-merged) ipq807x
allign to this new implementation. Backport this patch to kernel 5.15 to
fix support for smem parser for ipq806x target.
Fixes: 88bf652525 ("ipq806x: 5.15: replace dtsi patches with upstream version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move patch wrongly placed in backport dir to pending dir as they still
didn't got merged upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move MGLRU patches from pending to backport as they got merged upstream.
These are direct porting from one of the dev so it's better to just move
than trying to backport them again from upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move mvebu aardvark patch from pending to backport as they got merged
upstream.
One additional patch is needed as a later fixup for it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move sfp HALNy patch from pending to backport as they got merged
upstream. The patch was reordered and one was squashed in the upstream
variant.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
CONFIG_MAC80211_MESH isn't defined for this package, rendering the patch
useless. Match protecting the access of sta_info.mesh with the very same
define declaring it.
Fixes 45109f69a6 "mac80211: fix compile error when mesh is disabled"
Signed-off-by: Andre Heider <a.heider@gmail.com>
This updates mac80211 to version 5.15.74-1 which is based on kernel
5.15.74.
The removed patches were applied upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The switches support different actions for incoming ethernet multicast
frames with Reserved Multicast Addresses (01-80-C2-00-00-{01-2F}). The
current code will set the 2-bit action field to FLOOD (0x3) for most
classes, but the highest bit is always unset for the relevant control
registers. This means the DROP (0x1) action being used for these
classes; whatever class the MSB happens to be in.
For RTL838x, this results in {20,23-2F} frames being dropped, instead of
flooding all ports. On other switch generations, {0F,1F,2F} frames are
dropped. This is inconsistent, and appears to be a mistake. Remove this
inconsistency by flooding all multicast frames with RMA addresses.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The multicast setup function rtl838x_eth_set_multicast_list() checks if
the current SoC is a RTL839x family device. However, the function is
only included in the RTL838x ops table, so this path should never be
taken, making this dead code. rtl839x_eth_set_multicast_list() is
already present in the RTL839x ops table, so it should be safe to remove
this branch.
While touching the code, also re-sort the functions to match sorting
elsewhere, with rtl838x coming before rtl839x.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Currently several messages at KERN_INFO level are printed for every FDB
del/dump operation. This can cause a significant slowdown for example
while using "bridge fdb", and may even trigger a watchdog.
Remove most of these log messages, as the new L2 table debugfs node
should be a good replacement. Change the remaining messages to
KERN_DEBUG level.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
