With the old ubus dsl API, the numbers for the individual line_states and
power_states were also returned. These were not ported to the new DSL
C-API. This commit adds the missing information.
For this the internal values are mapped to numbers.
* additional JSON output for state_num:
"state_num": <map_state_number>
Since not all values are meaningful only the following values are
implemented, this can be extended if the future.
* LSTATE_MAP_NOT_INITIALIZED
* LSTATE_MAP_EXCEPTION
* LSTATE_MAP_IDLE
* LSTATE_MAP_SILENT
* LSTATE_MAP_HANDSHAKE
* LSTATE_MAP_FULL_INIT
* LSTATE_MAP_SHOWTIME_NO_SYNC
* LSTATE_MAP_SHOWTIME_TC_SYNC
* LSTATE_MAP_RESYNC
* additinal JSON output for power_level:
"power_state_num": <map_power_satte_number>,
Since there are not so many here, all are mapped.
* PSTATE_MAP_NA,
* PSTATE_MAP_L0,
* PSTATE_MAP_L1,
* PSTATE_MAP_L2,
* PSTATE_MAP_L3,
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
v6:
Add state LSTATE_MAP_NOT_INITILIZED at the beginning of the list
Start the list LSTATE_MAP with -1
Reviewed-by: Andre Heider <a.heider@gmail.com>
(cherry picked from commit 4407d45d96)
Switch to Actual Net Data Rate (ACTNDR) for speed reporting on lantiq VDSL modems
Refer to ITU-T G.997.1 chapter 7.5.2.8
Independent whether retransmission is used or not in a given transmit direction:
- In L0 state, this parameter reports the Net Data Rate (as specified in G.992.3, G.992.5 or G.993.2) at which the bearer channel is operating.
- In L2 state, the parameter contains the Net Data Rate (as specified in G.992.3, G.992.5 or G.993.2) in the previous L0 state.
Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com>
Reviewed-by: Andre Heider <a.heider@gmail.com>
(cherry picked from commit 4f27ea7c33)
This commit adds monitoring for a couple of DSL line features that are
present in the lantiq firmware blobs.
* G.INP ON/OFF
* Trellis encoding ON/OFF
* Virtaul Noise ON/OFF
* Bitswap ON/OFF
Difference in size for ltq-vdsl-app = 1k
Difference in size for kmod-ltq-vdsl-vr9 < 1k
Reviewed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com>
(cherry picked from commit 48162e4c0c)
U-Boot uses the "bootpartition" variable stored in
"u-boot-env2" to select the active system partition. Allow
updates to enable system switching from OpenWrt.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit 11d24ffe96)
Switch the Netgear DTSI for the Realtek target from the OEM partition
naming scheme to accepted OpenWrt naming practices. A quick git grep for
'u-boot-env' e.g. in the OpenWrt tree turns up almost 500 hits whereas
grepping for 'bdinfo' (the OEM equivalent) returns a meagre 14.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
(cherry picked from commit 1601b39b61)
Otherwise, the last defined value will be set for all devices.
Fixes: c6c8d597e1 ("realtek: Add generic zyxel_gs1900 image definition")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 851dadc257)
The rtl83xx-phy driver is necessary for proper configuration of the
PHYs if U-Boot hasn't done that.
1000Base-T SFPs often contains a Marvell 88E1111 and will not work
without this driver. Include it by default to support copper SFPs.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit 07bf5aaa4c)
There is no need to define a static link or a phy for the sfp
ports. Using phy-mode and managed properties to describe the
link to the sfp phy.
We have to keep the now unconnected virtual "phys" because the
switch driver uses their "phy-is-integrated" property to figure
out which ports to enable as fibre ports.
Acked-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit e8d391bd46)
From the validate docs in include/linux/phylink.h:
When state->interface is PHY_INTERFACE_MODE_NA, phylink expects the
MAC driver to return all supported link modes.
Tested-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit 785d830e88)
This bug was the root cause for the failing sfp driver.
Acked-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit b8e473d18c)
The ZyXEL GS1900-8 is a 8 port switch without any PoE functionality or
SFP ports, but otherwise similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-8 v1.2
* SoC: Realtek RTL8380M 500 MHz MIPS 4KEc
* Flash: Macronix MX25L12835F 16 MiB
* RAM: Nanya NT5TU128M8GE-AC 128 MiB DDR2 SDRAM
* Ethernet: 8x 10/100/1000 Mbit
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
8 ethernet port status LEDs (green, SoC controlled)
* Buttons: 1 on-off glide switch at the back (not configurable)
1 reset button at the right side, behind the air-vent
(not configurable)
1 reset button on front panel (configurable)
* Power 12V 1A barrel connector
* UART: 1 serial header (JP2) with populated standard pin connector on
the left side of the PCB, towards the back. Pins are labelled:
+ VCC (3.3V)
+ TX (really RX)
+ RX (really TX)
+ GND
the labelling is done from the usb2serial connector's point of
view, so RX/ TX are mixed up.
Serial connection parameters for both devices: 115200 8N1.
Installation
------------
Instructions are identical to those for the GS1900-10HP and GS1900-8HP.
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-10HP is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only boot off the first partition anyway (hardcoded in the DTS). To
make sure we are manipulating the first partition, issue the following
commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-8-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-generic-zyxel_gs1900-8-squashfs-sysupgrade.bin
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e6ba970b6e)
Add a new common device definition for the Zyxel GS1900 line of
switches.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit c6c8d597e1)
Demote a number of debugging printk's to pr_debug to avoid log
nosie. Several of these functions are called as a result of
userspace activity. This can cause a lot of log noise when
userspace does periodic polling.
Most of this could probably be removed completely, but let's
keep it for now since these drivers are still in development.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit ba220ad2fd)
This adds the necessary nuts and bolts for the uboot settings for both the ZyXEL GS1900-8HP v1 and v2.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
(cherry picked from commit b5bc53813d)
If service() is called w/o parameter then the status display for services
with multiple instances is incorrect. E.g. samba4 or wpad have 2 instances.
root@OpenWrt:~# /etc/init.d/samba4 status
running
root@OpenWrt:~# /etc/init.d/wpad status
running
Before change:
/etc/init.d/samba4 enabled stopped
/etc/init.d/wpad enabled stopped
After change:
/etc/init.d/samba4 enabled running
/etc/init.d/wpad enabled running
Signed-off-by: Alexander Egorenkov <egorenar-dev@posteo.net>
(cherry picked from commit 9318f61556)
Since KERNEL_SWAP is only enabled by default for !SMALL_FLASH targets, we need
to check if the current kernel supports swap before trying to configure
zram-swap, as opkg can't check for kernel dependencies.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
(cherry picked from commit 565dfeb128)
Without 'BUILD_DEVICES' defined, the U-Boot related package won't be
automatically selected when building for Toradex Apalis device.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(cherry picked from commit 8c3383799a)
Looks like 'openat', 'pipe2' and 'ppoll' are now needed, possibly due
to changes on libraries used by umdns now using slightly different
calls.
Found using
/etc/init.d/umdns trace
now use umdns, ie. cover all ubus call etc., then
/etc/init.d/umdns stop
find list of syscalls traced in /tmp/umdns.*.json
Fixes: FS#3355 ("UMDNS: does not start on master with seccomp")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 00a85a1634)
Now that ujail supports seccomp also on Aarch64, add missing syscall
'fstat' to the list of allowed syscalls.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit d28880cdd8)
The mt7530_{r,w}32 operation over MDIO uses 3 mdiobus operations and
does not hold a lock, which causes a race condition when multiple
threads try to access a register, they may get unexpected results.
To avoid this, handle the MDIO lock manually, and use the unlocked
__mdiobus_{read,write} in the critical section.
This fixes the "Ghost VLAN" artifact[1] in MT7530/7621 when the VLAN
operation and the swconfig LED link status poll race between each other.
[1] https://forum.openwrt.org/t/mysterious-vlan-ids-on-mt7621-device/64495
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
(cherry picked from commit f99c9cd9c4)
Fix the PLL register value for 10 Mbit/s link modes on the UniFi AC Lite
/ Mesh / LR. Otherwise, 10 Mbit/s links do not transfer data.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 956407292d)
Fix the PLL register value for 10 Mbit/s link modes on TP-Link EAP
boards using a AR8033 SGMII PHY.
Otherwise, 10 Mbit/s links do not transfer data.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Tested-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit bbff6239e2)
e78ea9bd26 Update Nios II libm-test-ulps.
98bb18f52a malloc: Fix a realloc crash with heap tagging [BZ 27468]
fc4ecce85b S390: Also check vector support in memmove ifunc-selector [BZ #27511]
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
(cherry picked from commit d49f1acff1)
For some reason, one of the configure checks results in some infinite
loop and ends up spawning endless gcc processes, causing OOM. Just pass
a configure var to avoid it.
Same fix as 6e23813c1e
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit fc093c3f9c)
Reduce spi-max-frequency for Xiaomi MI Router 4AG model
Xiaomi MI Router 4AG MTD uses two flash chips (no specific on router versions when produced from factory) - GD25Q128C and W25Q128BV.
These flash chips are capable of high frequency, but due to poor board design or manufacture process.
We are seeing the following errors in the linux kernel bootup:
`spi-nor spi0.0: unrecognized JEDEC id bytes: cc 60 1c cc 60 1c
spi-nor: probe of spi0.0 failed with error -2`
This causes the partitions not to be detected
`VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6`
Then creates a bootloop and a bricked router.
The solution to limit this race condition is to reduce the frequency from 80 mhz to 50 mhz.
Signed-off-by: David Bentham <db260179@gmail.com>
(cherry picked from commit 17e690017d)
The crypto engine in Armada 370 SoCs is currently broken. It can be
checked installing the required packages for testing openssl with hw
acceleration:
opkg install openssl-util
opkg install kmod-cryptodev
opkg install libopenssl-devcrypto
After configuring /etc/ssl/openssl.cnf to let openssl use the crypto
engine for digest operations, and performing some checksums..
md5sum 10M-file.bin
openssl md5 10M-file.bin
...we can see they don't match.
There might be an alignment or size constraint issue caused by the
idle-sram area.
Use the whole crypto sram and disable the idle-sram area to fix it. Also
disable the idle support by adding the broken-idle property to prevent
accessing the disabled idle-sram.
We don't care about disabling the idle support since it is already broken
in Armada 370 causing a huge performance loss because it disables
permanently the L2 cache. This was reported in the Openwrt forum and
elsewhere by Debian users with different board models.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(cherry picked from commit 2e1ebe96c6)
The GL.iNet GL-MV1000 is booting from eMMC and the images for it are in
theory sysupgrade compatible. But the platform upgrade scripts were not
adjusted to select the mmcblock device as upgrade target. This resulted in
a failed sysupgrade because the mtd device (NOR flash) was instead tried to
be modified by the sysupgrade script.
Fixes: 050c24f05c ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit 07e5e03711)
The Buffalo Linkstation LS421DE NAS lacks an uboot env config file.
Create it via scripts.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(cherry picked from commit 4f8da19572)
Fixes boot loader LZMA decompression issue,
reported by GitHub user KOLANICH at [0].
The reported LZMA ERROR has date of 2020-07-20, soon after
the device support landed:
Ralink UBoot Version: 3.5.2.4_ZyXEL
....
3: System Boot system code via Flash.
Image Name: MIPS OpenWrt Linux-4.14.187
Created: 2020-07-20 3:39:11 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1472250 Bytes = 1.4 MB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover
[0] fea232ae8f (commitcomment-45016560)
Fixes: 4dc9ad4af8 ("ramips: add support for ZyXEL Keenetic Lite Rev.B")
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
(cherry picked from commit dd3c1ad8ee)
This fixes partitioning on Linksys EA9500. With this change only the
currently used firmware MTD partition gets parsed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit a3c7633ddc)
Respect the generic kernel config setting, which is "enabled" tree-wide, as
previously done for sunxi.
Ref: 247ef4d98b ("sunxi: enable CONFIG_BPF_SYSCALL and CONFIG_EMBEDDED")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
(cherry picked from commit 41948c9c1b)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
CRYPTO_DEV_CCP depends on X86 or ARM64
CRYPTO_DEV_CCP_DD depends on CPU_SUP_AMD or ARM64
Compiling this driver makes sense for x86 mainly. If one day support for
ARM64 board with AMD Secure Processor gets added this package may be
updated.
Trying to build this package on bcm4908 was causing:
ERROR: module 'build_dir/target-aarch64_cortex-a53_musl/linux-bcm4908_generic/linux-5.4.110/drivers/crypto/ccp/ccp-crypto.ko' is missing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit cb3fb45ed1)
Currently it's not possible to flash factory images on devices shipped
with vendor firmware versions 1.1.0 Build 20201120 rel. 50406 (published
2020-12-22):
(curFw_ver, newFw_ver) == (1.1, 1.0) [NM_Error](nm_checkSoftVer) 00848: Firmwave not supports, check failed.
[NM_Error](nm_checkUpdateContent) 01084: software version dismatched
[NM_Error](nm_buildUpgradeStruct) 01188: checkUpdateContent failed.
They've even following note in release notes:
Note: You will be unable to downgrade to the previous firmware version
after updating this firmware.
This version check in vendor firmware is implemented in
/usr/bin/nvrammanager binary likely as following C code[1]:
sscanf(buf, "%d.%d.%*s",&upd_fw_major, &upd_fw_minor);
...
if (((int)upd_fw_major < (int)cur_fw_major) ||
((ret = 1, cur_fw_major == upd_fw_major && (upd_fw_minor < (int)cur_fw_minor)))) {
ret = 0;
printf("[NM_Error](%s) %05d: Firmwave not supports, check failed.\r\n\r\n","nm_checkSoftVer" ,0x350);
}
...
return ret;
So in order to fix this and make it future proof it should be enough to
ship our factory firmware images with major version 7 (lucky number).
Tested on latest firmware version 1.1.2 Build 20210125 rel.37999:
Firmwave supports, check OK.
(curFw_ver, newFw_ver) == (1.1, 7.0) check firmware ok!
Flashing back to vendor firmware
c7v5_us-up-ver1-1-2-P1[20210125-rel37999]_2021-01-25_10.33.55.bin works
as well:
U-Boot 1.1.4-gbec22107-dirty (Nov 18 2020 - 18:19:12)
...
Firmware downloaded... filesize = 0xeeae77 fileaddr = 0x80060000.
Firmware Recovery file length : 15642231
Firmware process id 2.
handle_fw_cloud 146
Image verify OK!
Firmware file Verify ok!
product-info:product_name:Archer C7
product_ver:5.0.0
special_id:55530000
[Error]sysmgr_cfg_checkSupportList(): 1023 @ specialId 45550000 NOT Match.
Firmware supports, check OK.
Firmware Recovery check ok!
1. https://gist.github.com/ynezz/2e0583647d863386a66c3d231541b6d1
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit e6d66375cb)
When $(FPIC) gets expanded on the command line (for instance
when setting environment variables for libtool, configure, or
make) we can't count on it not needing quoting (i.e. it could
contain multiple flags separated with spaces).
Fixes: dc31191ec3 ("build: make sure asm gets built with -DPIC")
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
(cherry picked from commit 7fae64cc06)
Refreshed all patches.
The following patches were manually changed:
* 610-netfilter_match_bypass_default_checks.patch
* 611-netfilter_match_bypass_default_table.patch
* 802-can-0002-can-rx-offload-fix-long-lines.patch
* 802-can-0003-can-rx-offload-can_rx_offload_compare-fix-typo.patch
* 802-can-0004-can-rx-offload-can_rx_offload_irq_offload_timestamp-.patch
* 802-can-0005-can-rx-offload-can_rx_offload_reset-remove-no-op-fun.patch
* 802-can-0006-can-rx-offload-Prepare-for-CAN-FD-support.patch
* 802-can-0018-can-flexcan-use-struct-canfd_frame-for-CAN-classic-f.patch
The can-dev.ko model was moved in the upstream kernel.
Compile-tested on: x86/64, armvirt/64, ath79/generic
Runtime-tested on: x86/64, armvirt/64, ath79/generic
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move some disabled symbols found in armvirt target to generic.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
(cherry picked from commit 12e942b1fd)
LPAE should be disabled as the Cortex-A8 cores don't support it,
and the kernel will crash on boot if it's enabled.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Fixes issue openwrt/packages#14921, whereby inline ASM wasn't getting
built as PIC; look at gmp-6.2.1/mpn/x86/pentium/popcount.asm for
example:
ifdef(`PIC',`
...
for a routine that exists in both PIC and non-PIC versions.
Make sure that wherever $(FPIC) gets passed as a variable expansion
that it gets quoted where necessary (such as setting environment
variables in shell commands).
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
(cherry picked from commit af22991e03)
