Based on original ar71xx eg200 board files
Tested working:
* usb hub, storage and serial port
* ethernet
* wifi
* leds
* button
sysupgrade from self->self passes validity checks.
sysupgrade from old ar71xx->ath79 passes. (however this doesn't migrate
wireless driver configs)
Only unknown issue is the existance of a /sys/class/leds/ath9k-phy0,
which doesn't "exist"
Signed-off-by: Karl Palsson <karlp@etactica.com>
I-O DATA WN-GX300GR is a 2.4 GHz band 11n router, based on MediaTek
MT7621S.
Specification:
- MT7621S (1-Core, 2-Threads)
- 64 MB of RAM
- 8 MB of Flash (SPI)
- 2T2R 2.4 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 115200 bps (U-Boot, OpenWrt)
Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Rename OpenWrt initramfs image for WN-GX300GR to "uImageWN-GX300GR"
and place it in the TFTP directory
3. Set the IP address of the computer to 192.168.99.8, connect to the
LAN port of WN-GX300GR, and start the TFTP server on the computer
4. Connect power cable to WN-GX300GR and turn on the router
5. Press "1" key on the serial console to interrupt boot process on
U-Boot, press Enter key 3 times and start firmware download via TFTP
6. WN-GX300GR downloads initramfs image and boot with it
7. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-GX300GR
8. Wait ~150 seconds to complete flasing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
The ART partition of the Lima board stores exactly three mac addresses:
* 0x0: eth0
* 0x6: eth1
* 0x1002: wmac
The first two are correctly assigned in the mach file but the latter points
to 0x800. But this position is set to ff:ff:ff:ff:ff:ff. Luckily, the
driver falls back in ath9k_hw_init_macaddr to the EEPROM mac address when
it doesn't find a valid mac address in the platform_data.
Remove this bogus offset to the ART partition to directly load the wmac via
the EEPROM data in the ART partition.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Some of the ubi-tools in the upstream mtd-utils have been
broken by a bad patch upstream. It causes major breakage
during sysupgrade when the kernel, rootfs, ... volumes
are deleted in the wrong order.
This patch therefore reverts the faulty upstream commit which
fixes the bug.
linux-mtd mailing-list thread:
<http://lists.infradead.org/pipermail/linux-mtd/2018-June/081562.html>
Cc: John Crispin <john@phrozen.org>
Reported-by: L. Wayne Leach <LLeachii@aol.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Node /cpus/cpu@0 has a unit name, but no reg property
Node /cpus/cpu@1 has a unit name, but no reg property
Node /cpuintc@0 has a unit name, but no reg property
Node /cpuclock@0 has a unit name, but no reg property
Node /sysclock@0 has a unit name, but no reg property
Node /pcie@1e140000/pcie0 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie0 missing bus-range for PCI bridge
Node /pcie@1e140000/pcie1 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie1 missing bus-range for PCI bridge
Node /pcie@1e140000/pcie2 missing ranges for PCI bridge (or not a bridge)
Node /pcie@1e140000/pcie2 missing bus-range for PCI bridge
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This reverts commit 8a570921b5.
This seems to have been accidentally reverted. This fixes mt7620 and
mt7628.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Define USB port power on/off GPO as voltage regulator type instead of
exposing as a normal GPIO.
The GPO is now controlled by the USB driver via the voltage regulator
definition. The regulator is of fixed output type (5V for USB) hence the
GPO switches power on/off to USB pin 1 (Vcc)
USB port power is enabled on driver load and disabled on driver unload.
Enable kernel support for fixed voltage regulator types on mt7621.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This patch fixes a dtc warning that shows up for every device
Warning (unit_address_vs_reg): Node /soc/ad-hoc-bus has a reg or ranges property, but no unit name
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
qcom-ipq4018-ex6100v2.dtb: Warning (reg_format): "reg" property in
/led_spi/led_gpio@0 has invalid length (4 bytes)
qcom-ipq4018-ex6100v2.dtb: Warning (avoid_default_addr_size):
Relying on default #size-cells value for /led_spi/led_gpio@0
Cc: Thomas Hebb <tommyhebb@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Some devices like the Mikrotik RB912 only have 1 USB port
which is shared between an USB A type port, and the mini PCIe socket.
Toggling a gpio selects the output to which USB is connected.
Since kernel 4.9, gpio base is rounded up to a value of 32.
Commit 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values") accounts correctly for that.
In this commit, rb912 sees it's value changed from AR934X_GPIO_COUNT (23) to 32
This means that the USB toggle gpio number actually also changes from 52 to 61.
But ..
Some of these GPIO numbers are also used in other locations, like the boardfile.
The author forgot to also change them over there.
Switching the USB port to mPCIe now shows my modem is correctly discovered again:
[ 2863.864471] usb 1-1: new high-speed USB device number 4 using ehci-platform
[ 2864.055303] usb 1-1: config 1 has an invalid interface number: 8 but max is 3
[ 2864.062728] usb 1-1: config 1 has no interface number 1
[ 2864.074567] qcserial 1-1:1.0: Qualcomm USB modem converter detected
[ 2864.081474] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB0
[ 2864.111960] qcserial 1-1:1.2: Qualcomm USB modem converter detected
[ 2864.118976] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB1
[ 2864.139808] qcserial 1-1:1.3: Qualcomm USB modem converter detected
[ 2864.146777] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB2
[ 2864.165276] qmi_wwan 1-1:1.8: cdc-wdm0: USB WDM device
[ 2864.171879] qmi_wwan 1-1:1.8 wwan0: register 'qmi_wwan' at usb-ehci-platform-1, WWAN/QMI device, 02:00:44:ed:3b:11
Fixes: 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Cc: Robin Leblon <robin.leblon@ncentric.com>
Cc: Felix Fietkau <nbd@nbd.name>
8e29d86 linuxrc: remove superfluous shebang line
12d2045 gitignore: remove Windows stuff
57d8969 Add travis hint
8edf4cc sdimage: use fsync before closing the device (fixes#1)
d395b31 uuc: fix some compiler warnings
Signed-off-by: Krystian Kozak <krystian.kozak20@gmail.com>
This reverts a change made in Sep 2017 [1] which introduced
MSG_DONTROUTE flag to prevent udhcpc from reaching out to servers on a
different subnet. That change violates RFC2131 by forcing fully
configured clients, who got their configurations through an offer
relayed by a DHCP relay, from renewing through a unicast request
directly to the DHCP server, resulting in the client resorting to
boradcasting lease extension requests instead of unicasting them,
further breaking RFC2131.
The problem with MSG_DONTROUTE appears when talking to a properly
configured DHCP server that rejects non-compliant requests. Such server
will reject lease extension attempts sent via broadcast rather than
unicast, as is the case with Finnish ISPs Telia and DNA as well as
Estonian ISP Starman. Once the lease expires without renewal, udhcpc
enters init mode, taking down the interfaces with it, and thus causing
interruption on every lease expiry. On some ISPs (such as the ones
mentioned above) that can be once every 10-20 minutes. The interruptions
appear in the logs as such:
----
udhcpc: sending renew to x.x.x.x
udhcpc: send: Network unreachable
udhcpc: sending renew to 0.0.0.0
udhcpc: sending renew to 0.0.0.0
...
udhcpc: lease lost, entering init state
Interface 'wan' has lost the connection
Interface 'wan' is now down
Network alias 'eth0' link is down
udhcpc: sending select for y.y.y.y
udhcpc: lease of y.y.y.y obtained, lease time 1200
Network alias 'eth0' link is up
Interface 'wan' is now up
----
During lease extension, a fully configured client should be able to
reach out to the server from which it recieved the lease for extension,
regardless in which network it is; that's up to the gateway to find. [2]
This patch ensures that.
[1]
http://lists.busybox.net/pipermail/busybox-cvs/2017-September/037402.html
[2]
https://www.netmanias.com/en/post/techdocs/6000/dhcp-network-protocol/
understanding-dhcp-relay-agents
Signed-off-by: Adi Shammout <adi.shammout@outlook.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
If log_file is specified, make sure its directory exists.
Signed-off-by: Karl Palsson <karlp@etactica.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Increase the available flash memory size in Netgear R7800
by taking into the use the unused "netgear" partition
that is located after the firmware partition.
Available flash space for kernel+rootfs+overlay increases
by 68 MB from 32 MB to 100 MB.
In a typical build, overlay space increases from 15 to 85,
increasing the package installation possibilities greatly.
Reverting to the OEM firmware is still possible, as the OEM
firmware contains logic to initialise the "netgear" partition
if its contents do not match expectations. In OEM firmware,
"netgear" contains 6 UBI sub-partitions that are defined in
/etc/netgear.cfg and initialisation is done by /etc/preinit
Tested with Openwrt master r7093-4fdc6ca31b and OEM V1.0.2.52
Reference to forum discussion in Netgear R7800 exploration thread:
https://forum.lede-project.org/t/netgear-r7800-exploration-ipq8065-qca9984/285/1118
(messages 1118-1158)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
ipq806x is all dual core processors. ipq807x is quad core. Removes this
from dmesg:
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
Signed-off-by: Rosen Penev <rosenp@gmail.com>
SourceForge is deprecated according to upstream, so switch to main site
for downloads.
Tested on Turris Omnia (mvebu).
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The board_name was being tested for "xlnx,zynq-zybo",
but the .dts compatible string is "digilent,zynq-zybo"
Also, sorted the boards alphabetically, and added an
error message for unsupported boards
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
This is no longer necessary since commit 57776e6
(base-files: remove default /etc/config/network,
generate it via board.d instead)
Run-tested: ZedBoard
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
After commit a1248da (zynq: convert to new image build code),
all boards, became unbootable, entering into a boot loop.
Replace the compressed kernel zImage by an uncompressed Image,
which is compressed after with gzip. Also, enable the creation
of an initramfs image by default.
Change images' filename to match the compatible string from the
respective .dts file (<vendor>_<model>). Also, use the shared
mkits.sh script and remove the target specific one.
Fixes: FS#1204
Run-tested: ZedBoard
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Problem - rapsberry pi 3 b/b+ does not boot with bcm2710 images!
How Raspberry Pi boots Actualy?
When Raspberry is switched on GPU is activated.
1. GPU execute First stage bootloader from ROM.
First stage bootloader mount the FAT boot partition on the SD card
and execute second stage bootloader (bootcode.bin).
2. Second stage bootloader (bootcode.bin) activate SDRAM.
Load the GPU firmware (start.elf).
3. GPU firmware (start.elf)
a) display Rainbow splash.
b) read firmware configuration file config.txt and
split the RAM using fixup.dat.
c) loads a cmdline.txt
d) enables the CPU.
e) loads the kernel image configurable via config.txt
In your target/linux/brcm2708/image/config.txt
493 ## kernel (string)
494 ## Alternative name to use when loading kernel.
495 ##
496 #kernel=""
it is not configured!
But in your target/linux/brcm2708/image/Makefile
75 KERNEL_IMG := kernel8.img
76 DEVICE_TITLE := Raspberry Pi 3B/3B+
you have kernel8.img
GPU Firmware search order by default for a PI 3 is:
kernel8.img if found boot in 64 bit mode
kernel8-32.img if found boot in 32 bit mode
kernel7.img if found boot in 32 bit mode
kernel.img if found boot in 32 bit mode
But a PI 2 will start the search from kernel7.img and
a PI 1 only looks for kernel.img.
Оbviously the kernel has been found.
But something goes wrong and the device is restarted.
In your package/kernel/brcm2708-gpu-fw/Makefile
11 PKG_NAME:=brcm2708-gpu-fw
12 PKG_VERSION:=2017-08-08
13 PKG_RELEASE:=e7ba7ab135f5a68b2c00a919ea9ac8d5528a5d5b
boot loader is 10 monts old.
In conclusion, the best way to solve the problem is
to update the boot loader!
Fixup_cd.dat and start_cd.elf files are not necessary.
These are used when GPU memory is set to 16 MB, which disables
some GPU features.
I did not remove them just in case!
cheers
Signed-off-by: Christo Nedev <christo.nedev@gmail.com>
Some board vendors actually changed the loader to expect the chip
to come up in 4-address-mode and flipped the ADP bit in the flash
chip's configuration register which makes it come up in 4-address-mode.
Hence it doesn't make sense to avoid switching to 4-address-mode on
those boards but the opposite as otherwise reboot hangs eg. on the
WrtNode2 boards. Fix this by checking the ADP register and only using
SPI_NOR_4B_READ_OP on chips which have ADP==0 (come up in 3-byte mode).
See also datasheet section 7.1.11 Power Up Address Mode (ADP)
Fixes: 22d982ea0 ("ramips: add support for switching between 3-byte and 4-byte addressing on w25q256 flash")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
5699354 extensions: fix build failure on fc28
e6359ee build: update ebtables.h from kernel and drop local unused copy
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
We recently increased the kernel partition size of the CPE/WBS 210/510.
This works fine for new installations of the factory image, but on
sysupgrades, the partition table read by the bootloader is not adjusted.
This limits the maximum size of the kernel loaded by the bootloader to the
old partition size.
While adjusting the partition table would be a cleanest solution, such a
migration would have to happen before an upgrade to a new version with a
newer kernel. This is error-prone and would require a two-step upgrade, as
we mark the partition table partition read-only.
Instead, switch from the lzma-loader with embedded kernel to the
okli-loader, so only the tiny lzma-loader is loaded by the bootloader as
"kernel", and the lzma-loader will then load the rest of the kernel by
itself.
Fixes: e39847ea2f ("ar71xx: increase kernel partition size for CPE/WBS 210/510")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Import all improvements made in the lzma-loader since development on the
ath79 target started.
This also reverts fe594bf90d ("ath79: fix loader-okli, lzma-loader"), as
is obsoleted by 2ad60168b6af ("ar71xx: lzma-loader: move padding workaround
to gzip step").
Likely, many of the changes should be ported to the ramips lzma-loader as
well, but I don't have a device to test this.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
By making the kernel argv array const, the .data section can always be
omitted from the laoder binary.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The text section in the ELF loader is aligned to the maximum page size,
which defaults to 64KB. Reduce it to the actual page size to avoid wasting
flash space for this alignment.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some devices (TP-Link TL-WR1043ND v1) don't boot reliably when the
uncompressed loader is too small. This was workarounded in the loader by
adding 512KB of padding to the .data section of the loader binary.
This approach had two issues:
- The padding was only working when .data was non-empty (otherwise the
section would become NOBITS, omitting it in the binary). .data was only
empty when no CMDLINE was set, leading to further workarounds like
fe594bf90d ("ath79: fix loader-okli, lzma-loader"), and this
workaround was only effective because a missing "const" led to the kernel
argv being stored in .data instead of .rodata
- The padding was not only added to the compressed .gz loader, but also
uncompressed .bin and .elf loaders. The prevented embedding the kernel
cmdline in the loader for non-gz loader types.
To fix both issues, move the creation of the padding from the linker script
to the gzip step.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
There are several long-standing issues present in the UCI shell API as
documented in https://wiki.openwrt.org/doc/devel/config-scripting. They
relate both to high-level, user-defined callback functions used to
process UCI config files, and also to low-level functions used within
scripts generally.
The related problems have been encountered now and in the past, e.g.
https://forum.openwrt.org/viewtopic.php?id=54295, and include:
a) UCI parsing option() function and user-defined option_cb() callbacks
being erroneously called during processing of "list" config file entries;
b) normal usage of the low-level config_set() unexpectedy calling any
defined option_cb() if present; and
c) handling of the list_cb() not respecting the NO_CALLBACK variable.
Root causes include a function stack "inversion", where the low-level
config_set() function incorrectly calls the high-level option() function,
intended only for processing the "option" keyword of UCI config files.
This change addresses the inversion and other issues, making the option
handling code more consistent and smaller, and simplifying developers'
usage of UCI callbacks.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
