We have had the testing kernel for several weeks now. Let's switch to 6.1
to have more testers. Additionally, 6.6 is already in the pipeline.
Signed-off-by: Nick Hainke <vincent@systemli.org>
* Increase flash SPI frequency to 50MHz
The maximum SPI frequency of MX25L6406EM2I is 86 MHz,
but in this patch 50 MHz was chosen as a safe value.
* Update Ethernet MAC addresses
Till now LAN/WAN MAC addresses were flipped
compared to stock firmware.
* Fix Wi-Fi LEDs by adding mt76 led nodes
* Fix LAN port order
LAN ports are in reverse order of switch ports.
* Fix the well-known "LZMA ERROR 1" error by using lzma-loader
* Set uImage name, which enables installation via stock web interface:
1. Upload **initramfs** image file to the web page.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Unlike the recovery image, this initramfs-factory image can be flashed
using the stock firmware web interface (from any active boot partition),
as well as the bootloader recovery web page. Drop the recovery image in
favor of the factory image.
Installation via stock/recovery web interface:
1. Flash **initramfs-factory** image through the web page.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The "0x80001000" address logically comes from "loadaddr-y" variable for
mt7621 subtarget. Let's replace the hardcoded value with the predefined
variable. This change is purely cosmetic.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Contrary to common ipTIME NOR devices, the "Config" partition of T5004
and AX2004M contain normal U-Boot environment variables. Renaming the
partition into "u-boot-env" serves for better description, and it also
conforms to common naming practice in OpenWrt.
This patch might also be extended to A3004T, but its u-boot-env
partition layout has not been confirmed yet.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
AX2004M uses NMBM on its NAND flash, but it was not enabled in DTS as the
device support [1] had been added before NMBM feature in mtk_bmt driver [2].
Let's enable it now.
With this change, there is a low possibility of boot failure after
sysupgrade from older versions. As AX2004M already has gone through
two stable releases in the meantime, it would be safe to warn users
by bumping DEVICE_COMPAT_VERSION.
[1] 37753f34ac ("ramips: add support for ipTIME AX2004M")
[2] 06382d1af7 ("kernel: add support for mediatek NMBM flash mapping support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The original commit had an invalid setting of the
led status for this device.
There is no gpio pin connected to that led so lets
remove these from the u7621-01 dtsi file.
Signed-off-by: David Bentham <db260179@gmail.com>
TP-Link Archer C5 v4 is a dual band router with 5 GbE ports
Advertised as AC1200 for its 867Mbps (2x2) 5GHz band
and 300 Mbps (2x2) 2.4GHz band.
Specs:
- SoC: MediaTek MT7620A
- Ethernet: 5x GbE ports (Realtek RTL8367S)
- Wireless 2.4GHz: MediaTek MT7620A
- Wireless 5GHz: MediaTek MT7612E
- RAM: 64MiB
- ROM: 8MiB (GD25Q64CSIG)
- 1 USB 2.0 port
- 2 Buttons (WPS and reset)
- 8 LEDs
Flash instructions:
Currently one has to install OpenWrt only via the serial console
1. Rename the factory.bin to to test.bin
2. start a TFTP server from IP address 192.168.0.225 and serve the image named test.bin
3. connect your device to the LAN port
4. power up the router and press 4 on the console to stop the boot process.
5. enter the following commands on the router console
tftp 0x80060000 test.bin
erase tplink 0x20000 0x7a0000
cp.b 0x80060000 0x20000 0x7a0000
reset
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[Update leds, add fast-read]
Signed-off-by: Gaspare Bruno <gaspare@anlix.io>
[Rebuilt version based on mt7620 tplink_archer.dtsi, support for external LNA, remove bad cell count info]
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
add back WIFI eprom addresses pointer in mt7621_dlink_dir-xx60-a1.dtsi
Change MAC address pointer from factory_e006 to factory_e000 + 3
same as used in D-link firmware 1.11 DIR-1960-A1
DIR-1960-A1,DIR-2640-A1,DIR-2660-A1,DIR-3060-A1
Clean-up MAC addresses in D-Link NOR devices DTS's
Change WIFI MAC Addressees to the same as NAND cousins macaddr_factory_e000 + ?
as later devices don't have the MAC address in factory configuration
same as used in D-Link firmware 1.30 DIR-878-A1
DIR-867-A1,DIR-878-A1,DIR-878-R1,DIR-882-A1,DIR-882-R1,DIR-1935-A1
* D-link software differs between source of wan address
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
The U-Boot binary for the RAVPower RP-WD009 has been renamed.
In order to be uniform with all other U-Boot binaries generated the SoC type has been prepended.
Set that new name also in the image build recipe for that device in order to fix build.
Fixes: 927334a8f7 ("uboot-mediatek: add basic build for ZBT-WG3526 (MT7621, 16M SPI-NOR)")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Replace previous patch adding paths and SerDes modes with patch series
pending upstream adding dedicated drivers for XFI T-PHY and USXGMII PCS,
extends LynxI PCS to be a standalone platform driver and as a consequence
makes much less changes to the actual Ethernet driver mtk_eth_soc.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Let's pick a bunch of useful phylink changes which allow us to keep
drivers in sync with mainline Linux.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This Qualcomm Gigabit phy driver was mistakenly added because
MT76x8 does not support external phy, and it only supports max
100M full duplex speed.
Fixes: cadf517107 ("ralink: add support for mt7628")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Backport QCA807x PHY patches merged upstream that introduce the new
concept of PHY package.
Also add in generic config the new Kconfig CONFIG_QCA807X_PHY.
All affected patch automatically refreshed with make
target/linux/refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
u64_stats_init() has been unable to handle NULL pointer since
6.1 kernel. This patch fixes kernel oops on mt76x8 and rt305x
sub-target.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
In the 5.15 kernel, we use the staging driver version instead of the
downstream file.
Fixes: 88d982e3bd ("ramips: 6.1: mt7621-dma: add hsdma driver to files")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Fixes errors in the form of:
make[9]: Entering directory '/home/nick/openwrt/build_dir/target-mipsel_24kc_musl/linux-ramips_mt7620/linux-6.1.77'
CC drivers/net/ethernet/ralink/mtk_eth_soc.o
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_init':
drivers/net/ethernet/ralink/mtk_eth_soc.c:1368:51: warning: passing argument 2 of 'of_get_mac_address' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
1368 | of_get_mac_address(priv->dev->of_node, dev->dev_addr);
| ~~~^~~~~~~~~~
In file included from drivers/net/ethernet/ralink/mtk_eth_soc.c:26:
./include/linux/of_net.h:16:59: note: expected 'u8 *' {aka 'unsigned char *'} but argument is of type 'const unsigned char *'
16 | extern int of_get_mac_address(struct device_node *np, u8 *mac);
| ~~~~^~~
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_probe':
drivers/net/ethernet/ralink/mtk_eth_soc.c:1641:9: error: too many arguments to function 'netif_napi_add'
1641 | netif_napi_add(netdev, &priv->rx_napi, fe_poll, napi_weight);
| ^~~~~~~~~~~~~~
In file included from ./include/linux/etherdevice.h:21,
from drivers/net/ethernet/ralink/mtk_eth_soc.c:21:
./include/linux/netdevice.h:2611:1: note: declared here
2611 | netif_napi_add(struct net_device *dev, struct napi_struct *napi,
| ^~~~~~~~~~~~~~
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[split commit and rewrite commit message]
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream commit f48dc6b96649 ("spi: Retire legacy GPIO handling") [0]
removed support using GPIOs as chip select. Fix it by replacing cs_gpio
with cs_gpiod.
[0] - f48dc6b966
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
[split commit and rewrite commit message]
Signed-off-by: Nick Hainke <vincent@systemli.org>
Change fe_hw_set_macaddr and the set_mac parameter to const to fix
errors in the form of:
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_set_mac_address':
drivers/net/ethernet/ralink/mtk_eth_soc.c:174:53: error: passing argument 2 of 'priv->soc->set_mac' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
174 | priv->soc->set_mac(priv, dev->dev_addr);
| ~~~^~~~~~~~~~
drivers/net/ethernet/ralink/mtk_eth_soc.c:174:53: note: expected 'unsigned char *' but argument is of type 'const unsigned char *'
drivers/net/ethernet/ralink/mtk_eth_soc.c: In function 'fe_hw_init':
drivers/net/ethernet/ralink/mtk_eth_soc.c:1220:45: error: passing argument 2 of 'priv->soc->set_mac' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
1220 | priv->soc->set_mac(priv, dev->dev_addr);
| ~~~^~~~~~~~~~
drivers/net/ethernet/ralink/mtk_eth_soc.c:1220:45: note: expected 'unsigned char *' but argument is of type 'const unsigned char *'
drivers/net/ethernet/ralink/mtk_eth_soc.c:1222:44: error: passing argument 2 of 'fe_hw_set_macaddr' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
1222 | fe_hw_set_macaddr(priv, dev->dev_addr);
| ~~~^~~~~~~~~~
drivers/net/ethernet/ralink/mtk_eth_soc.c:155:75: note: expected 'unsigned char *' but argument is of type 'const unsigned char *'
155 | static inline void fe_hw_set_macaddr(struct fe_priv *priv, unsigned char *mac)
| ~~~~~~~~~~~~~~~^~~
cc1: all warnings being treated as errors
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream dropped support for legacy driver [0]. Rewrite the driver like
the renesas pwm driver [1].
Fixes erros in the form of:
make: *** [/__w/openwrt/openwrt/openwrt/include/toplevel.mk:232: target/compile] Error 1
====== Make errors from logs/target/linux/compile.txt ======
| ^~~~~~~~~~~~~~
drivers/pwm/pwm-mediatek-ramips.c:107:19: note: (near initialization for 'mtk_pwm_ops.free')
drivers/pwm/pwm-mediatek-ramips.c:108:10: error: 'const struct pwm_ops' has no member named 'disable'
108 | .disable = mtk_pwm_disable,
| ^~~~~~~
drivers/pwm/pwm-mediatek-ramips.c:108:20: error: initialization of 'int (*)(struct pwm_chip *, struct pwm_device *, struct pwm_capture *, long unsigned int)' from incompatible pointer type 'void (*)(struct pwm_chip *, struct pwm_device *)' [-Werror=incompatible-pointer-types]
108 | .disable = mtk_pwm_disable,
| ^~~~~~~~~~~~~~~
drivers/pwm/pwm-mediatek-ramips.c:108:20: note: (near initialization for 'mtk_pwm_ops.capture')
cc1: all warnings being treated as errors
[0] - 0829c35dc5
[1] - ec00cd5e63
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream dropped slave_id in dai_dma [0]. So drop it also in the mt7620
support patch.
Fixes errors in the form of:
sound/soc/ralink/ralink-i2s.c: In function 'ralink_i2s_init_dma_data':
sound/soc/ralink/ralink-i2s.c:452:17: error: 'struct snd_dmaengine_dai_dma_data' has no member named 'slave_id'
452 | dma_data->slave_id = i2s->txdma_req;
| ^~
sound/soc/ralink/ralink-i2s.c:462:17: error: 'struct snd_dmaengine_dai_dma_data' has no member named 'slave_id'
462 | dma_data->slave_id = i2s->rxdma_req;
| ^~
[0] - https://lore.kernel.org/r/20211122222203.4103644-3-arnd@kernel.org
Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream changed in ed5c2f5fd10d ("i2c: Make remove callback return void")
the i2c driver's remove function to return no value. Adapt the driver code
to compile with 5.15 and 6.1 like it is done in other projects [0].
Fixes errors in the form of:
make[8]: Leaving directory '/home/nick/openwrt/build_dir/target-mipsel_24kc_musl/linux-ramips_mt7621/linux-6.1.29'
CC drivers/pinctrl/pinctrl-aw9523.o
drivers/pinctrl/pinctrl-aw9523.c:1117:19: error: initialization of 'void (*)(struct i2c_client *)' from incompatible pointer type 'int (*)(struct i2c_client *)' [-Werror=incompatible-pointer-types]
1117 | .remove = aw9523_remove,
| ^~~~~~~~~~~~~
drivers/pinctrl/pinctrl-aw9523.c:1117:19: note: (near initialization for 'aw9523_driver.remove')
cc1: all warnings being treated as errors
[0] - https://gitlab.com/ddcci-driver-linux/ddcci-driver-linux/-/merge_requests/10/diffs
Signed-off-by: Nick Hainke <vincent@systemli.org>
Apply the "109-drivers-mt7621-dma-handle-error-from-device_reset.patch"
directly on the downstream maintained dma driver.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Commit 87dd67f496f7 ("staging: mt7621-dma: remove driver from tree")
removed the mt7621-dma driver. Maintain the driver downstream in the
folder of the other mediatek drivers.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Fix DTS error in LED color/function conversion due to a bug in the
conversion script.
Fixes: 19c45b95db ("ramips: convert to new LED color/function format where possible")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant label with new LED color/function format declared.
This was needed previously when the new format wasn't supported by
leds.sh functions script. Now that is supported this property
can be removed in favor of the new format.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some of devices in this target have only 8 MiB space and are closing to
borders of usable space. Particularly, TP-Link RE305 v1 already suffers
from this issue[1], where with current partition layout, on release
images, there's not enough space for overlay. So activate small_flash
feature, which will remove some userspace hardening but will gain almost
1 MiB additional flash memory space. Here is small size comparison of
similar device (RE365 v1) with default config + LuCI:
kernel rootfs sysupgrade
current: 2305728 3635044 5964584
small_flash: 1713571 3320132 5047080
1. https://github.com/openwrt/openwrt/issues/14215
Suggested-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
-+-------------------------+-
| Model | NIC |
-+-------------------------+-
| All | MT7603 + MT7615 |
-+-------------------------+-
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Some MT7915 calibration data consists of two parts. The first part
"eeprom" size is 0xe00. The second part "precal" size is 0x19c10.
Though some devices may not have precal data, it's better to assume
that precal data exists as no users/developers confirm it. On the
other hand, some devices definitely do not contain precal data
because the EEPROM partition size is smaller than the precal NVMEM
cell size.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
TP-Link RE365 is a wireless range extender, hardware-wise resembles
RE305 with slight changes regarding buttons and LEDs.
Specification
SoC: MediaTek MT7628AN
RAM: 64 MiB DDR2
Flash: 8 MiB SPI NOR
WiFi: 2.4 GHz 2T2R integrated
5 GHz 2T2R MediaTek MT7612EN conncted to PCIe lanes
Ethernet: 1x 10/100 Mbps integrated
LEDs: 6x GPIO controlled
Buttons: 4x GPIO controlled
UART: row of 4 holes marked on PCB as J1, starting count from white
triangle
1. VCC (3.3V), 2. GND, 3. RX, 4. TX
baud: 57600, parity: none, flow control: none
Installation
1. Open web management interface.
2. Go to Settings > System Tools > Firmware upgrade.
3. Select "Browse" and select the OpenWrt image with factory.bin suffix.
4. After selecting "Upgrade" firmware writing process will start.
5. Wait till device reboots, power LED should stay solid when it's fully
booted, then it's ready for configuration through LAN port.
Additional information
With how device manufacturer patrtitioned the flash memory, it's possible
that with default packages set, initial factory.bin image won't be
created. In such case, try to reduce packages amount or use older release
for initial conversion to OpenWrt. Later You can use sysupgrade.bin
image with full set of packages because OpenWrt uses unpartitioned flash
memory space unused by vendor firmware.
Reverting to vendor firmware involves converting firmware using
tplink-safeloader with -z option (can be found in ImageBuilder or SDK)
and forcibly applying converted firmware as sysupgrade.
Known issues
WARNING: after removing casing of the device one is exposed to high
voltage and is in a risk of being electrocuted.
Caution when interfacing whith bootloader, saving its environment either
by issuing "saveenv" or selecting option "1: Load system code to SDRAM
via TFTP." in boot menu, any of those will lead to overwriting part of
kernel. This will lead to need of firmware recovery. The cause of this
issue is bootloader having environment offset on flash at 0x40000,
while kernel starts from 0x20000.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[Wrap long line in DTS]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
This commit:
1. Removes deprecated "label" property from the dts leds subnnodes;
2. Updates buttons and leds dts description according to kernel docs
examples.
Scope: devices well known to me.
Run-tested: TP-Link ec330-g5u, WiFire S1500.nbn
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
