Add support for W25N01JW, W25N02JWZEIF, W25N512GW, W25N02KWZEIR and W25N01GWZEIG.
Add support for W25N04KV.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16272
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SoC: MediaTek MT7621
Flash: 16MB (Macronix MX25L12805D)
RAM: 128MB
Serial: As marked on PCB, baudrate is 57600, DO NOT CONNECT 3.3V!!!
Ethernet: 4x 10/100/1000 Mbps (3x LAN + WAN)
WIFI0: MT7615 2.4GHz 802.11b/g/n
WIFI1: MT7615 5GHz 802.11ac
Antennas: 6x external (3 per radio), non-detachable
LEDs: Programmable power-LED (blue-colored)
Buttons: Reset
INSTALLATION:
Get rootshell using insructions from https://gist.github.com/ZIKH26/18693c67ee7d2f8d2c60231b19194c37
Download and flash image
On computer:
python -m http.server
On router:
cd /tmp
wget http://:8000/factory.bin
mtd -r write factory.bin firmware
Device should reboot at this point.
Reverting to stock:
Download archive with firmware from Ruijie's site and
get .bin file from it. Then write that binary to firmware
partition. After reboot, factory-reset the router using
reset button.
Signed-off-by: Yahor Leonenka <staryjakau@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16202
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ELECOM WSC-X1800GS is a 2.4/5 GHz band 11ax (Wi-Fi 6) mesh extender,
based on MT7621A
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
- Flash : RAW-NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7915D + MT7975D)
- Ethernet : 2x 10/100/1000 Mbps
- switch : MediaTek MT7530 (SoC)
- LEDs/Keys (GPIO): 9x/2x
- UART : through-hole on PCB ("J4")
- arrangement : 3.3V, GND, TX, RX from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 10.5 W)
Flash instruction using initramfs-factory image
1. Boot WMC-X1800GST normally
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt initramfs-factory image and click apply ("適用")
button
4. On initramfs image, download sysupgrade image to the device and
perform sysupgrade with that image
5. Wait ~120 seconds to complete flashing
Notes:
- The "firmware" partition on the stock image is only 0xF00000 (15 MiB)
and it's too small for the current OpenWrt firmware with UBI format.
So use the unused area at the end of NAND flash for rootfs (UBI).
MAC addresses:
LAN : 04:AB:18:xx:xx:6E (Factory, 0x3fff4 (hex))
2.4 GHz: 04:AB:18:xx:xx:6F (Factory, 0x3fffa (hex))
5 GHz : 04:AB:18:xx:xx:70 (Factory, 0x4 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16384
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ELECOM WMC-X1800GST is a 2.4/5 GHz band 11ax (Wi-Fi 6) mesh router,
based on MT7621A
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
- Flash : RAW-NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7915D + MT7975D)
- Ethernet : 3x 10/100/1000 Mbps
- switch : MediaTek MT7530 (SoC)
- LEDs/Keys (GPIO): 9x/5x
- UART : through-hole on PCB ("J4")
- arrangement : 3.3V, GND, TX, RX from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 11.5 W)
Flash instruction using initramfs-factory image
1. Boot WMC-X1800GST normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt initramfs-factory image and click apply ("適用")
button
4. On initramfs image, download sysupgrade image to the device and
perform sysupgrade with that image
5. Wait ~120 seconds to complete flashing
Notes:
- The "firmware" partition on the stock image is only 0xF00000 (15 MiB)
and it's too small for the current OpenWrt firmware with UBI format.
So use the unused area at the end of NAND flash for rootfs (UBI).
MAC addresses:
LAN : 04:AB:18:xx:xx:BF (Factory, 0x3fff4 (hex))
WAN : 04:AB:18:xx:xx:C0 (Factory, 0x3fffa (hex))
2.4 GHz: 04:AB:18:xx:xx:C1 (Factory, 0x4 (hex))
5 GHz : 04:AB:18:xx:xx:C2
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16384
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Compile LED support to swconfig and phy modules
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for building DSA switch drivers as kernel modules.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for building multiple phy drivers as kernel modules
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for building both upstream and downstream ag71xx drivers
as modules.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rename the downstream ag71xx driver to ag71xx-legacy.
It allows both upstream and downstream drivers to be compiled into modules.
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch add a version to uboot patches to help identify in
futures updates when they were upstreamed.
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware Spec
-SoC: Rockchip RK3588S
CPU: Quad-core ARM Cortex-A76(up to 2.4GHz) and quad-core Cortex-A55 CPU (up to 1.8GHz)
GPU: Mali-G610 MP4, compatible with OpenGLES 1.1, 2.0, and 3.2, OpenCL up to 2.2 and Vulkan1.2
VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder, 4K@60fps AV1 decoder, 8K@30fps H.264 and H.265
NPU: 6TOPs, supports INT4/INT8/INT16/FP16
-RAM: 64-bit 4GB/8GB LPDDR4X at 2133MHz
-Flash: 32GB/None eMMC, at HS400 mode
-Ethernet: one Native Gigabit Ethernet, and one PCIe 2.5G Ethernet
-USB: one USB 3.0 Type-A and one USB 2.0 Type-A
-PCIe: one M.2 Key M connector with PCIe 2.1 x1
-HDMI:
compatible with HDMI2.1, HDMI2.0, and HDMI1.4 operation
support up to 7680x4320@60Hz
Support RGB/YUV(up to 10bit) format
-microSD: support up to SDR104 mode
-GPIO:
30-pin 2.54mm header connector
up to 1x SPI, 3x UARTs, 3x I2Cs, 2x SPDIFs, 1x I2Ss, 3x PWMs, 20x GPIOs
-Debug: UART via 3-Pin 2.54mm header, or on-board USB-C to UART
-LEDs: 4 x GPIO Controlled LED (SYS, WAN, LAN, LED1)
-others:
2 Pin 1.27/1.25mm RTC battery input connector for low power RTC IC HYM8563TS
MASK button for eMMC update
one user button
-Power supply: USB-C, support PD, 5V/9V/12V/20V input
-PCB: 8 Layer, 62x90x1.6mm
-Ambient Operating Temperature: 0℃ to 70℃
Installation:
Uncompress the OpenWrt sysupgrade and write image to the SD card using dd (dd if=*.img of=/*)
eMMC Installation:
Boot from the SD card
Uncompress the OpenWrt sysupgrade image
fash to eMMC : dd if=*.img of=/dev/mmcblk1
sync
remove SD card
reboot
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
1- The NanoPi R6C is a SBC by FriendlyElec based on the Rockchip RK3588s.
It comes with 4GB or 8GB of RAM, a microSD card slot, optional 32GB eMMC
storage, one M.2 M-Key connector, one RTL8211F 1GbE and one RTL8125
2.5GbE Ethernet port, one USB 2.0 Type-A and one USB 3.0 Type-A port, a
HDMI port, a 30-pin GPIO header as well as multiple buttons and LEDs.
2- Renamed 000-backport-upstream-dts-sync.patch -> 000-v2024.10-rc1-backport-upstream-dts-sync.patch
to add the version when was applied upstream
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Same as 'nohostroute' option for GRE tunnels (commit 0f8b9addfc)
and IPIP tunnels (commit 46ce629fe0)
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15961
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport ir-receiver/minipcie/poweroff/spi/usb-c support and other
minor fixes for the NanoPC T6 board.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16443
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We have <netinet/sctp.h> header in lksctp-tools package,
but having this var set to 'no' prevents package's configure
to detect it.
Signed-off-by: Aleksey Vasilenko <aleksey.vasilenko@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16441
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update sysupgrade script (fortinet.sh) for Fortinet devices in
mvebu/cortexa9 and fix the following issues,
- Some individuals of FortiGate/FortiWiFi 30E/5xE devices has wrong
kernel/rootfs offsets in "firmware-info" partition and they are not
updated with the current sysupgrade script for Fortinet devices
(fortinet.sh).
As a result, the bootloader tries to load kernel data from the wrong
address and boot with it after OpenWrt installation.
The new script handles offsets in addition to length values.
and improve the following points.
- Only 2 bytes are handled with the current sysupgrade script
(fortinet.sh) for kernel/rootfs length. The new script handles 4 bytes
instead.
- The image names of image0/image1 are not handled and not updated when
sysupgrade. The new sysupgrade script handles it and update to
"<dist> <version> <revision>" if firmware metadata is available.
(ex.: "OpenWrt SNAPSHOT r27440-25384026")
log of new sysupgrade script (fortinet.sh):
Tue Sep 17 10:29:16 UTC 2024 upgrade: Performing system upgrade...
Image Index: 0
Image Name : "OpenWrt SNAPSHOT r27440-25384026"
--> "OpenWrt SNAPSHOT r27441-b3a0806a05"
kernel:
old: 0x003c4e00@0x00200000
new: 0x003c4e00@0x00200000
rootfs:
old: 0x005c0200@0x00800000
new: 0x005c0200@0x00800000
Unlocking kernel ...
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The mdio bus number of mv88e6xxx was changed to '0' from '1' and the
"mv88e6xxx-1:<addr>:<speed>" triggers are unavailable now.
Update triggers for "SPEED" LEDs to make working that LEDs again.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The driver for fixed voltage regulater uses "regulator-fixed" for
compatible string, not "fixed-regulator".
Fixes: 102dc5a625 ("mvebu: add support for FortiGate 50E")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rename the sysupgrade.tar step to sysupgrade.bin. The sysupgrade.tar is
used in other places and we prefer a sysupgrade.bin instead.
Fixes: fea2264d9f ("ramips: mt7621: Add DNA Valokuitu Plus EX400")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The sysupgrade-tar image build is not defined for this target, do not
add a build instruction for it. The build system will use the definition
from the dna_valokuitu-plus-ex400 board and the build will fail.
This fixes the build of the ramips target.
Fixes: 665c2154ef ("ramips: add basic support for tp-link er605-v2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Change I2C pin flags to GPIO_ACTIVE_HIGH and change SDA to GPIO1.
On my late production GL-AR750 (purchased 2024):
SCL = GPIO16
SDA = GPIO1
Bug report:
I2C bus doesn't work in GL-AR750
https://github.com/openwrt/openwrt/issues/16319
Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16406
Signed-off-by: Robert Marko <robimarko@gmail.com>
STRIP_KERNEL_EXPORTS is currently broken on kernel 6.6 and since this
is the only kernel currently supported, we should rather make it depend
on BROKEN instead of a kernel version until its fixed.
Link: https://github.com/openwrt/openwrt/pull/16440
Signed-off-by: Robert Marko <robimarko@gmail.com>
link: https://lore.kernel.org/all/2024091842-CVE-2024-46760-1eb3@gregkh
Description
===========
In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: usb: schedule rx work after everything is set up
Right now it's possible to hit NULL pointer dereference in
rtw_rx_fill_rx_status on hw object and/or its fields because
initialization routine can start getting USB replies before
rtw_dev is fully setup.
The stack trace looks like this:
rtw_rx_fill_rx_status
rtw8821c_query_rx_desc
rtw_usb_rx_handler
...
queue_work
rtw_usb_read_port_complete
...
usb_submit_urb
rtw_usb_rx_resubmit
rtw_usb_init_rx
rtw_usb_probe
So while we do the async stuff rtw_usb_probe continues and calls
rtw_register_hw, which does all kinds of initialization (e.g.
via ieee80211_register_hw) that rtw_rx_fill_rx_status relies on.
Fix this by moving the first usb_submit_urb after everything
is set up.
For me, this bug manifested as:
[ 8.893177] rtw_8821cu 1-1:1.2: band wrong, packet dropped
[ 8.910904] rtw_8821cu 1-1:1.2: hw->conf.chandef.chan NULL in rtw_rx_fill_rx_status
because I'm using Larry's backport of rtw88 driver with the NULL
checks in rtw_rx_fill_rx_status.
The Linux kernel CVE team has assigned CVE-2024-46760 to this issue.
Affected and fixed versions
===========================
Fixed in 6.6.51 with commit c83d464b82a8
Fixed in 6.10.10 with commit 25eaef533bf3
Fixed in 6.11 with commit adc539784c98
Please see https://www.kernel.org for a full list of currently supported
kernel versions by the kernel community.
Unaffected versions might change over time as fixes are backported to
older supported kernel versions. The official CVE entry at
https://cve.org/CVERecord/?id=CVE-2024-46760
will be updated if fixes are backported, please check that for the most
up to date information about this issue.
Affected files
==============
The file(s) affected by this issue are:
drivers/net/wireless/realtek/rtw88/usb.c
Mitigation
==========
The Linux kernel CVE team recommends that you update to the latest
stable kernel version for this, and many other bugfixes. Individual
changes are never tested alone, but rather are part of a larger kernel
release. Cherry-picking individual commits is not recommended or
supported by the Linux kernel community at all. If however, updating to
the latest release is impossible, the individual changes to resolve this
issue can be found at these commits:
https://git.kernel.org/stable/c/c83d464b82a8ad62ec9077637f75d73fe955635ahttps://git.kernel.org/stable/c/25eaef533bf3ccc6fee5067aac16f41f280e343ehttps://git.kernel.org/stable/c/adc539784c98a7cc602cbf557debfc2e7b9be8b3
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16420
Signed-off-by: Robert Marko <robimarko@gmail.com>
