Specifications:
- Device: ASUS RT-AX54 (AX1800S/HP,AX54HP)
- SoC: MT7621AT
- Flash: 128MB
- RAM: 256MB
- Switch: 1 WAN, 4 LAN (10/100/1000 Mbps)
- WiFi: MT7905 2x2 2.4G + MT7975 2x2 5G
- LEDs: 1x POWER (blue, configurable)
1x LAN (blue, configurable)
1x WAN (blue, configurable)
1x 2.4G (blue, not configurable)
1x 5G (blue, not configurable)
Flash by U-Boot TFTP method:
- Configure your PC with IP 192.168.1.2
- Set up TFTP server and put the factory.bin image on your PC
- Connect serial port(rate:115200) and turn on AP, then interrupt "U-Boot Boot Menu" by hitting any key
Select "2. Upgrade firmware"
Press enter when show "Run firmware after upgrading? (Y/n):"
Select 0 for TFTP method
Input U-Boot's IP address: 192.168.1.1
Input TFTP server's IP address: 192.168.1.2
Input IP netmask: 255.255.255.0
Input file name: openwrt-ramips-mt7621-asus_rt-ax1800hp-squashfs-factory.bin
- Restart AP aftre see the log "Firmware upgrade completed!"
Signed-off-by: Karl Chan <exkc@exkc.moe>
All boards using this DTSI are expected to have
the same 16 MB MX25L12845EMI-10G flash chip,
or a larger one which can also use 40 MHz frequency.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Although VLANs are used, the "eth0" device by itself
does not have a valid MAC, so fix that with preinit script.
More initvals added by editing the driver to print switch registers,
after the bootloader sets them but before openwrt changes them.
The register bits needed for the QCA8337 switch
can be read from interrupted boot (tftpboot, bootm)
by adding print lines in the switch driver ar8327.c
before 'qca,ar8327-initvals' is parsed from DTS and written
for example:
pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Use nvmem kernel subsystem to pull radio calibration data
with the devicetree instead of userspace scripts.
Existing blocks for caldata_extract are reordered alphabetically.
MAC address is set using the hotplug script.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: A8J-ESR900
Engenius ESR1200 is an indoor wireless router with
a gigabit ethernet switch, dual-band wireless,
internal antenna plates, and a USB 2.0 port
**Specification:**
- QCA9557 SOC 2.4 GHz, 2x2
- QCA9882 WLAN PCIe mini card, 5 GHz, 2x2
- QCA8337N SW 4 ports LAN, 1 port WAN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM
- UART at J1 populated, RX grounded
- 6 internal antenna plates (omni-directional)
- 5 LEDs, 1 button (power, 2G, 5G, WAN, WPS) (reset)
**MAC addresses:**
Base MAC address labeled as "MAC ADDRESS"
MAC "wanaddr" is not similar to "ethaddr"
eth0 *:c8 MAC u-boot-env ethaddr
phy0 *:c8 MAC u-boot-env ethaddr
phy1 *:c9 --- u-boot-env ethaddr +1
WAN *:66:44 u-boot-env wanaddr
**Serial Access:**
RX on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin
**Installation:**
Method 1: Firmware upgrade page
OEM webpage at 192.168.0.1
username and password "admin"
Navigate to Settings (gear icon) --> Tools --> Firmware
select the factory.bin image
confirm and wait 3 minutes
Method 2: TFTP recovery
Follow TFTP instructions using initramfs.bin
use sysupgrade.bin to flash using openwrt web interface
**Return to OEM:**
MTD partitions should be backed up before flashing
using TFTP to boot openwrt without overwriting flash
Alternatively, it is possible to edit OEM firmware images
to flash MTD partitions in openwrt to restore OEM firmware
by removing the OEM header and writing the rest to "firmware"
**TFTP recovery:**
Requires serial console, reset button does nothing at boot
rename initramfs.bin to 'uImageESR1200'
make available on TFTP server at 192.168.99.8
power board, interrupt boot by pressing '4' rapidly
execute tftpboot and bootm
**Note on ETH switch registers**
Registers must be written to the ethernet switch
in order to set up the switch's MAC interface.
U-boot can write the registers on it's own
which is needed, for example, in a TFTP transfer.
The register bits from OEM for the QCA8337 switch
can be read from interrupted boot (tftpboot, bootm)
by adding print lines in the switch driver ar8327.c
before 'qca,ar8327-initvals' is parsed from DTS and written.
for example:
pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: A8J-ESR1750
Engenius ESR1750 is an indoor wireless router with
a gigabit ethernet switch, dual-band wireless,
internal antenna plates, and a USB 2.0 port
**Specification:**
- QCA9558 SOC 2.4 GHz, 3x3
- QCA9880 WLAN PCIe mini card, 5 GHz, 3x3
- QCA8337N SW 4 ports LAN, 1 port WAN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM
- UART at J1 populated, RX grounded
- 6 internal antenna plates (omni-directional)
- 5 LEDs, 1 button (power, 2G, 5G, WAN, WPS) (reset)
**MAC addresses:**
Base MAC address labeled as "MAC ADDRESS"
MAC "wanaddr" is similar to "ethaddr"
eth0 *:58 MAC u-boot-env ethaddr
phy0 *:58 MAC u-boot-env ethaddr
phy1 *:59 --- u-boot-env ethaddr +1
WAN *:10:58 u-boot-env wanaddr
**Serial Access:**
RX on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin
**Installation:**
Method 1: Firmware upgrade page
NOTE: ESR1750 might require the factory.bin
for ESR1200 instead, OEM provides 1 image for both.
OEM webpage at 192.168.0.1
username and password "admin"
Navigate to Settings (gear icon) --> Tools --> Firmware
select the factory.bin image
confirm and wait 3 minutes
Method 2: TFTP recovery
Follow TFTP instructions using initramfs.bin
use sysupgrade.bin to flash using openwrt web interface
**Return to OEM:**
MTD partitions should be backed up before flashing
using TFTP to boot openwrt without overwriting flash
Alternatively, it is possible to edit OEM firmware images
to flash MTD partitions in openwrt to restore OEM firmware
by removing the OEM header and writing the rest to "firmware"
**TFTP recovery:**
Requires serial console, reset button does nothing at boot
rename initramfs.bin to 'uImageESR1200'
make available on TFTP server at 192.168.99.8
power board, interrupt boot by pressing '4' rapidly
execute tftpboot and bootm
**Note on ETH switch registers**
Registers must be written to the ethernet switch
in order to set up the switch's MAC interface.
U-boot can write the registers on it's own
which is needed, for example, in a TFTP transfer.
The register bits from OEM for the QCA8337 switch
can be read from interrupted boot (tftpboot, bootm)
by adding print lines in the switch driver ar8327.c
before 'qca,ar8327-initvals' is parsed from DTS and written.
for example:
pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: A8J-ESR900
Engenius ESR900 is an indoor wireless router with
a gigabit ethernet switch, dual-band wireless,
internal antenna plates, and a USB 2.0 port
**Specification:**
- QCA9558 SOC 2.4 GHz, 3x3
- AR9580 WLAN PCIe on board, 5 GHz, 3x3
- AR8327N SW 4 ports LAN, 1 port WAN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM
- UART at J1 populated, RX grounded
- 6 internal antenna plates (omni-directional)
- 5 LEDs, 1 button (power, 2G, 5G, WAN, WPS) (reset)
**MAC addresses:**
Base MAC address labeled as "MAC ADDRESS"
MAC "wanaddr" is not similar to "ethaddr"
eth0 *:06 MAC u-boot-env ethaddr
phy0 *:06 MAC u-boot-env ethaddr
phy1 *:07 --- u-boot-env ethaddr +1
WAN *:6E:81 u-boot-env wanaddr
**Serial Access:**
RX on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin
**Installation:**
Method 1: Firmware upgrade page
OEM webpage at 192.168.0.1
username and password "admin"
Navigate to Settings (gear icon) --> Tools --> Firmware
select the factory.bin image
confirm and wait 3 minutes
Method 2: TFTP recovery
Follow TFTP instructions using initramfs.bin
use sysupgrade.bin to flash using openwrt web interface
**Return to OEM:**
MTD partitions should be backed up before flashing
using TFTP to boot openwrt without overwriting flash
Alternatively, it is possible to edit OEM firmware images
to flash MTD partitions in openwrt to restore OEM firmware
by removing the OEM header and writing the rest to "firmware"
**TFTP recovery:**
Requires serial console, reset button does nothing at boot
rename initramfs.bin to 'uImageESR900'
make available on TFTP server at 192.168.99.8
power board, interrupt boot by pressing '4' rapidly
execute tftpboot and bootm
**Note on ETH switch registers**
Registers must be written to the ethernet switch
in order to set up the switch's MAC interface.
U-boot can write the registers on it's own
which is needed, for example, in a TFTP transfer.
The register bits from OEM for the AR8327 switch
can be read from interrupted boot (tftpboot, bootm)
by adding print lines in the switch driver ar8327.c
before 'qca,ar8327-initvals' is parsed from DTS and written.
for example:
pr_info("0x04 %08x\n", ar8xxx_read(priv, AR8327_REG_PAD0_MODE));
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Split the DTS to be used with similar boards made by Senao,
dual-band routers with Atheros / Qualcomm ethernet switch.
Set initvals for the switch in each device's DTS.
Set some common calibration nvmem-cells in DTSI.
While at it, fix MTD partition node names.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
By specifying the flag "denx,fit" for partition "kernel", the kernel
try to find rootfs in the same partition during boot. Reality is that
the placement of rootfs is precisely determined by the name of another
partition -"ubi".
It was also found that on some device (for example devices with NAND
chips), the "Denx search engine" manages to find roots at the end of
partition "kernel", but such partition doesn't exist and is empty
there.
Fix this by removing the "denx,fit" flag from partition "kernel". With
this change the original behavior of searchif rootfs in partition "ubi"
is restored.
Signed-off-by: Oleg S <remittor@gmail.com>
Enables use of NVMe storage devices with appropriate adapter in miniPCIe slots (including for boot)
in Turris 1.x routers and possibly NXP P2020RDB boards
(these are the only currently supported p2020 devices according to docs[^1]).
Proper detection, mountability and readability was proved to be working
on Turris 1.1, OpenWrt 21.02 with similar configuration.
Increases gzip compressed kernel size by approximately 37 KiB (from 3 703 KiB to 3 740 KiB).
Should boot from those devices be possible the driver needs to be built in.
Inclusion as a module would prevent this functionality.
CONFIG_BLK_DEV_NVME=y
Includes NVMe driver in the kernel.[^2]
CONFIG_NVME_CORE=y
Selected by CONFIG_BLK_DEV_NVME.[^3] Not necessarily needed to be enabled explicitly,
but included to match the form of similar functionality implementations
for mvebu, x86_64 and rockchip_armv8 targets.
CONFIG_NVME_MULTIPATH disabled explicitly to prevent using more space than necessary.
[^1]: https://openwrt.org/docs/techref/targets/mpc85xx
[^2]: https://cateee.net/lkddb/web-lkddb/BLK_DEV_NVME.html
[^3]: https://cateee.net/lkddb/web-lkddb/NVME_CORE.html
Signed-off-by: Šimon Bořek <simon.borek@nic.cz>
Bumping max frame size has significantly affected network performance
and memory usage. It was done by upstream commit that first appeared in
the 5.7 release.
Allocating 512 (BGMAC_RX_RING_SLOTS) buffers, 10 k each, is clearly a
bad idea on 32 MiB devices. This commit fixes support for Linksys E1000
V2.1 which gives up after allocating ~346 such buffers running 5.15
kernel.
Ref: 230c9da963 ("bcm53xx: revert bgmac back to the old limited max frame size")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Most of the time when booting kernel prints a warning from
mm/page_alloc.c when pstore/ramoops is being initialized and ramoops is
not functional.
Fix this by moving ramopps node into reserved-memory block as described
in kernel documentation.
Fixes: 2964e5024c ("ipq806x: kernel ramoops storage for C2600/AD7200")
Signed-off-by: Filip Matijević <filip.matijevic.pz@gmail.com>
After switching to DSA, the LAN ports in Cell C RTL30VW have swapped numbers. Assigning the right numbers.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
When fstools is unable to parse our root=<...> arg correctly, it can
fall back to scanning all block devices for a 'rootfs_data' partition.
This fallback was deemed wrong (or at least, a breaking/incompatible
change) for some targets, so we're forced to opt back into it with
fstools_partname_fallback_scan=1.
Without this, OnHub devices will use a rootfs-appended loop device for
rootfs_data instead of the intended 3rd partition.
While I'm at it, just move all the boot args into the 'cros-vboot'
build rule, instead of using the custom bootargs-append. All cros-vboot
subtargets here are using the same rootwait (to support both eMMC and
USB boot) and root/partition args.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[ drop unrelated comments in commit description ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The phy-mode property must be defined on the MAC instead of the PHY. Define
phy-mode under gmac1 which the external phy is connected to.
Tested-by: Petr Louda <petr.louda@outlook.cz>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Match interface numbers with printed numbers on device enclosure and
assign first port as WAN interface.
Notes
Serial console is available through RJ-45 port with Cisco pinout
baud: 19200, parity: none, flow control: none
The device is setup with UEFI. To enter setup hold DEL or ESC key on
boot. Default UEFI Administrator password is: bcndk1
For users using graphics IC it's advisable to disable display with:
i915.disable_display=1
appending to kernel command line inside bootloader, to save about
0.5-0.6W energy on idle.
For users not using graphics IC, disable it in UEFI, this will save about
1.5W energy on idle.
Pins marked CN19 are ATX power On/Off button.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
These devices have a partition table stored in flash, which compensates
for any pre-existing bad blocks by enlarging the respective partition.
This means that the current static partition table is only correct for
devices without any bad blocks.
Typical results of this mismatch are degraded wireless performance and
wrong MAC addresses, when the factory partition is shifted due to a bad
block somewhere before it. If there is a bad block already before the
ubi partition, then OpenWrt may not run at all because the kernel can't
find the rootfs.
Use the on-flash partition table to fix these issues. Replace the two
reserved partitions by the full partition list, as the driver does not
allow merging them.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Kconfig docs say:
> The default value deliberately defaults to 'n' in order to avoid
> bloating the build.
Apply this rule everywhere, to avoid more cloning of bad examples
Signed-off-by: Tony Butler <spudz76@gmail.com>
This commit adds support for the V4 hardware revision of the Deco M4R.
V4 is a complete overhaul of the hardware compared to V1 and V2,
and is much more similar to the Archer C6 V3 and C6U V1.
Specifications:
SoC: MediaTek MT7621AT (2 cores at 880 MHz, 4 threads)
RAM: Kingston D1216ECMDXGJD (256 MB)
Wireless 2.4 GHz: MediaTek MT7603EN
Wireless 5 GHz: MediaTek MT7613BEN
Flash: 16 MB SPI NOR
Installation:
Flash the *-factory.bin image in the U-Boot recovery webserver.
You can trigger this webserver by holding the reset button until the LED
flashes yellow, or by hooking up to serial pads on the board (clearly
labeled GND, RX and TX) and pressing `x` early in boot.
Once the factory image has been flashed, you can use the regular upgrade
procedure with sysupgrade images for subsequent flashes.
Signed-off-by: Mark Ceeha <hi@shiz.me>
Tested-by: Mark Ceeha <hi@shiz.me>
This makes the patches and the kernel configuration apply on top of
kernel 5.15.
The following patch was removed because the old IDE subsystem was
removed from upstream kernel:
target/linux/bcm47xx/patches-5.15/610-pci_ide_fix.patch
This was tested successfully on a ASUS WL-500g Premium V1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
shellcheck warns against it with SC2086. It also hides a bug that
shellcheck marks with SC2015. Fixed those with explicit if/else.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Instead of using the shell's evaluation, use grep's -q parameter.
Found with shellcheck's SC2143.
Also replaced a head call with grep's -m.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Enable the CPU frequency scaling statistics in kernel config.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Use generic earlycon on Linux Kernel instead of initialization in platform
setup.
And also, drop bootargs with console= parameter from I-O DATA BSH-G24MB. It
uses 115200bps as baud-rate, the same as default in rtl838x.dtsi.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
