D-Link DGS-1210-16 hangs when rebooting and has no support for the reset
button.
Fix both by enabling the same GPIOs for reboot and the reset button as
already used for D-Link DGS-1210-20 and D-Link DGS-1210-28.
Signed-off-by: Richard Kunze <kunze@tivano.de>
(cherry picked from commit 92c21b2e18)
Huawei AP5030DN is a dual-band, dual-radio 802.11ac Wave 1 3x3 MIMO
enterprise access point with two Gigabit Ethernet ports and PoE
support.
Hardware highlights:
- CPU: QCA9550 SoC at 720MHz
- RAM: 256MB DDR2
- Flash: 32MB SPI-NOR
- Wi-Fi 2.4GHz: QCA9550-internal radio
- Wi-Fi 5GHz: QCA9880 PCIe WLAN SoC
- Ethernet 1: 10/100/1000 Mbps Ethernet through Broadcom B50612E PHY
- Ethernet 2: 10/100/1000 Mbps Ethernet through Marvell 88E1510 PHY
- PoE: input through Ethernet 1 port
- Standalone 12V/2A power input
- Serial console externally available through RJ45 port
- External watchdog: SGM706 (1.6s timeout)
Serial console:
9600n8 (9600 baud, no stop bits, no parity, 8 data bits)
MAC addresses:
Each device has 32 consecutive MAC addresses allocated by
the vendor, which don't overlap between devices.
This was confirmed with multiple devices with consecutive
serial numbers.
The MAC address range starts with the address on the label.
To be able to distinguish between the interfaces,
the following MAC address scheme is used:
- eth0 = label MAC
- eth1 = label MAC + 1
- radio0 (Wi-Fi 5GHz) = label MAC + 2
- radio1 (Wi-Fi 2.4GHz) = label MAC + 3
Installation:
0. Connect some sort of RJ45-to-USB adapter to "Console" port of the AP
1. Power up the AP
2. At prompt "Press f or F to stop Auto-Boot in 3 seconds",
do what they say.
Log in with default admin password "admin@huawei.com".
3. Boot the OpenWrt initramfs from TFTP using the hidden script
"run ramboot". Replace IP address as needed:
> setenv serverip 192.168.1.10
> setenv ipaddr 192.168.1.1
> setenv rambootfile
openwrt-ath79-generic-huawei_ap5030dn-initramfs-kernel.bin
> saveenv
> run ramboot
4. Optional but recommended as the factory firmware cannot
be downloaded publicly:
Back up contents of "firmware" partition using the web interface or ssh:
$ ssh root@192.168.1.1 cat /dev/mtd11 > huawei_ap5030dn_fw_backup.bin
5. Run sysupgrade using sysupgrade image. OpenWrt
shall boot from flash afterwards.
Return to factory firmware (using firmware upgrade package downloaded from
non-public Huawei website):
1. Start a TFTP server in the directory where
the firmware upgrade package is located
2. Boot to u-boot as described above
3. Install firmware upgrade package and format the config partitions:
> update system FatAP5X30XN_SOMEVERSION.bin
> format_fs
Return to factory firmware (from previously created backup):
1. Copy over the firmware partition backup to /tmp,
for example using scp
2. Use sysupgrade with force to restore the backup:
sysupgrade -F huawei_ap5030dn_fw_backup.bin
3. Boot AP to U-Boot as described above
Quirks and known issues
-----------------------
- On initial power-up, the Huawei-modified bootloader suspends both
ethernet PHYs (it sets the "Power Down" bit in the MII control
register). Unfortunately, at the time of the initial port, the kernel
driver for the B50612E/BCM54612E PHY behind eth0 doesn't have a resume
callback defined which would clear this bit. This makes the PHY unusable
since it remains suspended forever. This is why the backported kernel
patches in this commit are required which add this callback and for
completeness also a suspend callback.
- The stock firmware has a semi dual boot concept where the primary
kernel uses a squashfs as root partition and the secondary kernel uses
an initramfs. This dual boot concept is circumvented on purpose to gain
more flash space and since the stock firmware's flash layout isn't
compatible with mtdsplit.
- The external watchdog's timeout of 1.6s is very hard to satisfy
during bootup. This is why the GPIO15 pin connected to the watchdog input
is configured directly in the LZMA loader to output the CPU_CLK/4 signal
which keeps the watchdog happy until the wdt-gpio kernel driver takes
over. Because it would also take too long to read the whole kernel image
from flash, the uImage header only includes the loader which then reads
the kernel image from flash after GPIO15 is configured.
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
[fixed 6.6 backport patch naming]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 06cdc07f8c)
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 8GB eMMC or 128 MB SPI-NAND
RAM: 256MB
Ethernet: 5x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset
USB: M.2(B-key) for 4G/5G Module
Power: DC 12V 1A
UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | VCC RX TX GND | <= |
| ----------------- |
--------------------------
The U-boot menu will automatically appear at startup, and then select
the required options through UP/DOWN Key.
NAND Flash and eMMC Flash instructions:
1. Set your computers IP adress to 192.168.1.2.
2. Run a TFTP server providing the sysupgrade.bin image.
3. Power on the router, into the U-Boot menu.
4. Select "2. Upgrade firmware"
5. Update sysupgrade.bin file name, input server IP and input device
IP (if they deviate from the defaults)
6. Wait for automatic startup after burning
Signed-off-by: Allen Zhao <allenzhao@unielecinc.com>
(cherry picked from commit 640b0b79ff)
ttyS2 is the default console used for all rockchip boards.
The redundant 'console=tty1' parameter now breaks the console due to
recent procd update.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 163c3d0bde)
We have hardware IOMMU support and this is totally unnecessary.
The given value is also unreasonable, it's too small and causes
kernel panic in some cases:
[ 5706.856473] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 28672 bytes), total 512 (slots), used 498 (slots)
[ 5706.864451] sdhci-dwcmshc fe310000.mmc: swiotlb buffer is full (sz: 65536 bytes), total 512 (slots), used 464 (slots)
This parameter seems to be added by mistake, so remove it.
Fixes: e35c7ab51f ("rockchip: merge bootscript")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 50e6c8ae8d)
52144f723bec pex: after receiving data update req, notify peer of local address/port
29aacb9386e0 pex: track indirect hosts (reachable via gateway) as peers without adding them to wg
48049524d4fc pex: do not send peer notifications for hosts with a gateway
12ac684ee22a pex: do not query for hosts with a gateway
203c88857354 pex: fix endian issues on config transfer
a29d45c71bca network: fix endian issue in converting port to network id
cbbe9d337a17 unet-cli: emit id by default
806457664ab6 unet-cli: strip initial newline in usage message
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a112ed4126)
This adds support for the Iomega ix4-200d device in uboot-envtools.
Signed-off-by: Sander van Deijck <sander@vandeijck.com>
(cherry picked from commit 2cfe86d383)
Set 12mA driving strength for SPI-NAND pins like the stock firmware's
bootloader does as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 45a2109353)
These two patches are fixing minor problems with DNSSEC found shortly
after the dnsmasq 2.90 release.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 28c87d7ecd)
dnsmasq was recently updated to 2.90, but PKG_RELEASE was not reset to 1.
Fixes: 838a27f64f ("dnsmasq: version 2.90")
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 694e647784)
Bump to 2.90 to get upstream's fix for DNSSEC KeyTrap (CVE-2023-50387,
CVE-2023-50868) among many other goodies and fixes (notably, upstream
568fb024... fixes a UAF in cache_remove_uid that was routinely crashing
dnsmasq in my deployment).
Catch up our 200-ubus_dns.patch, too.
Signed-off-by: Nathaniel Wesley Filardo <nwfilardo@gmail.com>
(cherry picked from commit 838a27f64f)
If the dnsmasq process forks to handle TCP connections, it closes the ubus
context. But instead of changing the daemon wide pointer to NULL, only the
local variable was adjusted - and this portion of the code was even dropped
(dead store) by some optimizing compilers.
It makes more sense to change the daemon->ubus pointer because various
functions are already checking it for NULL. It is also the behavior which
ubus_destroy() implements.
Fixes: d8b33dad0b ("dnsmasq: add support for monitoring and modifying dns lookup results via ubus")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit 711dcb7763)
Some Aquantia PHYs (e.g. AQR113C) require firmware to be uploaded by
host system. With built-in drivers this doesn't work in OpenWrt /
embeddded as filesystem isn't available during PHY probe. That results
in delays like:
[ 1.588068] Aquantia AQR113C mdio-bus:00: Falling back to sysfs fallback for: Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld
[ 64.526387] Aquantia AQR113C mdio-bus:00: failed to find FW file Rhe-05.06-Candidate9-AQR_Mediatek_23B_P5_ID45824_LCLVER1.cld (-110)
Switch to module to postpone PHY probe to init state.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 3bd79e6136)
Marvell's thermal sensors do not support interrupts, so we need to
poll them. Reading temperature every second should be enough to
control the fan.
While at it, also make sure fan speed is reduced again if temperature
goes down.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit fc177695e0)
Debian changelog:
intel-microcode (3.20240312.1) unstable; urgency=medium
* New upstream microcode datafile 20240312 (closes: #1066108)
- Mitigations for INTEL-SA-INTEL-SA-00972 (CVE-2023-39368):
Protection mechanism failure of bus lock regulator for some Intel
Processors may allow an unauthenticated user to potentially enable
denial of service via network access.
- Mitigations for INTEL-SA-INTEL-SA-00982 (CVE-2023-38575):
Non-transparent sharing of return predictor targets between contexts in
some Intel Processors may allow an authorized user to potentially
enable information disclosure via local access. Affects SGX as well.
- Mitigations for INTEL-SA-INTEL-SA-00898 (CVE-2023-28746), aka RFDS:
Information exposure through microarchitectural state after transient
execution from some register files for some Intel Atom Processors and
E-cores of Intel Core Processors may allow an authenticated user to
potentially enable information disclosure via local access. Enhances
VERW instruction to clear stale register buffers. Affects SGX as well.
Requires kernel update to be effective.
- Mitigations for INTEL-SA-INTEL-SA-00960 (CVE-2023-22655), aka TECRA:
Protection mechanism failure in some 3rd and 4th Generation Intel Xeon
Processors when using Intel SGX or Intel TDX may allow a privileged
user to potentially enable escalation of privilege via local access.
NOTE: effective only when loaded by firmware. Allows SMM firmware to
attack SGX/TDX.
- Mitigations for INTEL-SA-INTEL-SA-01045 (CVE-2023-43490):
Incorrect calculation in microcode keying mechanism for some Intel
Xeon D Processors with Intel SGX may allow a privileged user to
potentially enable information disclosure via local access.
* Fixes for other unspecified functional issues on many processors
* Updated microcodes:
sig 0x00050653, pf_mask 0x97, 2023-07-28, rev 0x1000191, size 36864
sig 0x00050656, pf_mask 0xbf, 2023-07-28, rev 0x4003605, size 38912
sig 0x00050657, pf_mask 0xbf, 2023-07-28, rev 0x5003605, size 37888
sig 0x0005065b, pf_mask 0xbf, 2023-08-03, rev 0x7002802, size 30720
sig 0x00050665, pf_mask 0x10, 2023-08-03, rev 0xe000015, size 23552
sig 0x000506f1, pf_mask 0x01, 2023-10-05, rev 0x003e, size 11264
sig 0x000606a6, pf_mask 0x87, 2023-09-14, rev 0xd0003d1, size 307200
sig 0x000606c1, pf_mask 0x10, 2023-12-05, rev 0x1000290, size 299008
sig 0x000706a1, pf_mask 0x01, 2023-08-25, rev 0x0040, size 76800
sig 0x000706a8, pf_mask 0x01, 2023-08-25, rev 0x0024, size 76800
sig 0x000706e5, pf_mask 0x80, 2023-09-14, rev 0x00c4, size 114688
sig 0x000806c1, pf_mask 0x80, 2023-09-13, rev 0x00b6, size 111616
sig 0x000806c2, pf_mask 0xc2, 2023-09-13, rev 0x0036, size 98304
sig 0x000806d1, pf_mask 0xc2, 2023-09-13, rev 0x0050, size 104448
sig 0x000806ec, pf_mask 0x94, 2023-07-16, rev 0x00fa, size 106496
sig 0x000806f8, pf_mask 0x87, 2024-01-03, rev 0x2b000590, size 579584
sig 0x000806f7, pf_mask 0x87, 2024-01-03, rev 0x2b000590
sig 0x000806f6, pf_mask 0x87, 2024-01-03, rev 0x2b000590
sig 0x000806f5, pf_mask 0x87, 2024-01-03, rev 0x2b000590
sig 0x000806f4, pf_mask 0x87, 2024-01-03, rev 0x2b000590
sig 0x00090661, pf_mask 0x01, 2023-09-26, rev 0x0019, size 20480
sig 0x00090672, pf_mask 0x07, 2023-09-19, rev 0x0034, size 224256
sig 0x00090675, pf_mask 0x07, 2023-09-19, rev 0x0034
sig 0x000b06f2, pf_mask 0x07, 2023-09-19, rev 0x0034
sig 0x000b06f5, pf_mask 0x07, 2023-09-19, rev 0x0034
sig 0x000906a3, pf_mask 0x80, 2023-09-19, rev 0x0432, size 222208
sig 0x000906a4, pf_mask 0x80, 2023-09-19, rev 0x0432
sig 0x000906c0, pf_mask 0x01, 2023-09-26, rev 0x24000026, size 20480
sig 0x000906e9, pf_mask 0x2a, 2023-09-28, rev 0x00f8, size 108544
sig 0x000906ea, pf_mask 0x22, 2023-07-26, rev 0x00f6, size 105472
sig 0x000906ec, pf_mask 0x22, 2023-07-26, rev 0x00f6, size 106496
sig 0x000906ed, pf_mask 0x22, 2023-07-27, rev 0x00fc, size 106496
sig 0x000a0652, pf_mask 0x20, 2023-07-16, rev 0x00fa, size 97280
sig 0x000a0653, pf_mask 0x22, 2023-07-16, rev 0x00fa, size 97280
sig 0x000a0655, pf_mask 0x22, 2023-07-16, rev 0x00fa, size 97280
sig 0x000a0660, pf_mask 0x80, 2023-07-16, rev 0x00fa, size 97280
sig 0x000a0661, pf_mask 0x80, 2023-07-16, rev 0x00fa, size 96256
sig 0x000a0671, pf_mask 0x02, 2023-09-14, rev 0x005e, size 108544
sig 0x000b0671, pf_mask 0x32, 2023-12-14, rev 0x0122, size 215040
sig 0x000b06a2, pf_mask 0xe0, 2023-12-07, rev 0x4121, size 220160
sig 0x000b06a3, pf_mask 0xe0, 2023-12-07, rev 0x4121
sig 0x000b06e0, pf_mask 0x11, 2023-09-25, rev 0x0015, size 138240
* New microcodes:
sig 0x000a06a4, pf_mask 0xe6, 2024-01-03, rev 0x001c, size 136192
sig 0x000b06a8, pf_mask 0xe0, 2023-12-07, rev 0x4121, size 220160
sig 0x000c06f2, pf_mask 0x87, 2023-11-20, rev 0x21000200, size 549888
sig 0x000c06f1, pf_mask 0x87, 2023-11-20, rev 0x21000200
* source: update symlinks to reflect id of the latest release, 20240312
* changelog, debian/changelog: fix typos
-- Henrique de Moraes Holschuh <hmh@debian.org> Tue, 12 Mar 2024 20:28:17 -0300
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 7b911a9c49)
Router Asus TUF AX6000 have second MaxLinear GPY211 PHY controller for 2.5Gb LAN port.
The 5'th LAN port have inverted status of the LED.
Based on the commit from main branch 90fbec8 we could set proper status of the LED.
Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
(cherry picked from commit b22539b5fe)
Signed-off-by: Tom Herbers <mail@tomherbers.de>
Add downstream DT property to setup the PHY LEDs of the MaxLinear
GPY211 PHY in such way that the VDD of the LED is driven by the SoC
pin rather than the GND (which is the default).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 90fbec89be)
[removed patches for kernel 6.1]
Signed-off-by: Tom Herbers <mail@tomherbers.de>
Fixes: d522ccecb2 ("filogic: add support for ASUS TUF AX6000")
Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
(cherry picked from commit 0c3f4bd85e)
Signed-off-by: Tom Herbers <mail@tomherbers.de>
This commit adds support for Z-ROUTER ZR-2660 (also known as Routerich
AX1800) wireless WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (AMD/Spansion S34ML01G2)
- WLAN :
- 2.4 GHz : MediaTek MT7905D/MT7975 (14c3:7916), b/g/n/ax, MIMO 2x2
- 5 GHz : MediaTek MT7915E (14c3:7915), a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x4 (1x WAN, 3x LAN)
- USB : 1x 2.0
- UART : 3.3V, 115200n8, pins are silkscreened on the pcb
- Buttons : 1x Reset
- LEDs : 1x WiFi 2.4 GHz (green)
1x WiFi 5 GHz (green)
1x LAN (green)
1x WAN (green)
1x WAN no-internet (red)
- Power : 12 VDC, 1 A
Installation
------------
1. Run tftp server on your PC (IP: 192.168.2.2) and put OpenWrt initramfs
image (initramfs.bin) to the tftp root dir
2. Open the following link in the browser to enable telnet:
http://192.168.2.1/cgi-bin/telnet_ssh
3. Connect to the router (default IP: 192.168.2.1) using telnet shell
(credentials - user:admin)
4. Run the following commands in the telnet shell (this will install
OpenWrt initramfs image on nand flash):
cd /tmp
tftp -g -r initramfs.bin 192.168.2.2
mtd write initramfs.bin firmware
mtd erase firmware_backup
reboot
5. Copy OpenWrt sysupgrade image (sysupgrade.bin) to the /tmp dir of the
router
6. Connect to the router (IP: 192.168.1.1) using ssh shell and run
sysupgrade command:
sysupgrade -n /tmp/sysupgrade.bin
Return to stock
---------------
1. Copy stock firmware (stock.bin) to the /tmp dir of the router using scp
2. Run following command in the router shell:
cd /tmp
mtd write stock.bin firmware
reboot
Recovery
--------
Connect uart (pins are silkscreened on the pcb), interrupt boot process by
pressing any key, use u-boot menu to flash stock firmware image or OpenWrt
initramfs image.
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | 24:0f:5e:xx:xx:4c | label |
| WAN | 24:0f:5e:xx:xx:4d | label+1 |
| WLAN 2g | 24:0f:5e:xx:xx:4e | label+2 |
| WLAN 5g | 24:0f:5e:xx:xx:4f | label+3 |
+---------+-------------------+-----------+
The WLAN 2.4 MAC was found in 'factory', 0x4
The LAN MAC was found in 'factory', 0xfff4
The WAN MAC was found in 'factory', 0xfffa
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
(cherry picked from commit 1d3d6ef826)
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
A patch to resolve an issue was found in MediaTek's GPL-licensed SDK:
In the mtk_ppe_stop() function, the PPE scan mode is not disabled before
disabling the PPE. This can potentially lead to a hang during the process
of disabling the PPE.
Without this patch, the PPE may experience a hang during the reboot test.
Reference: b40da332df
Suggested-by: Bc-bocun Chen <bc-bocun.chen@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 003b9ff61c)
Backport commit faa5f17fe2 ("kernel: mtk_eth_soc: release
MAC_MCR_FORCE_LINK only when MAC is up") to Linux 5.15 as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 33d6ba5045)
The ubootmod bootlaoder for EX5601-T0 uses two partitions
in ubi to store enviroment variables. so proper config
is needed.
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
(cherry picked from commit 2a0805fd3d)
Flash procedure is described in next commit.
TLDR:
Copy preloader and uboot to /tmp and write them in the mtd.
This will also require new UBI partition and
volumes to boot openwrt.
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-bl31-uboot.fip fip
Changelist:
- Added profile for 4k+256 SPI NAND_TYPE
- Added basic Zyxel EX5601-T0 uboot profile
Backported from hitech95 branch:
- Button RESET pin fix
- Button WPS pin fix
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
(cherry picked from commit a9cf87027e)
The YunCore G720 is a dual band 802.11ax router with 5 GbE ports.
Specs:
- SoC: MediaTek MT7621
- Ethernet: 5x GbE ports (built-in MT7530)
- Wireless 2.4GHz / 5GHz: MediaTek MT7915E
- RAM: 256MiB
- ROM: 16MiB (W25Q128)
- 1 Button (reset)
- 8 LEDs (1x system, 2x wifi, 5x switch ports)
Flash instructions:
The vendor firmware is based on OpenWrt, the sysupgrade image can be
flashed using the '-F' (force) option on the CLI.
Make sure not to keep settings when doing so.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 65df33fc76)
This device is very similar, if not identical, to the TP-Link AX23 v1
but is targeted at service providers and features a completely different
flash layout.
Hardware
--------
CPU: MediaTek MT7621 DAT
RAM: 128MB DDR3 (integrated)
FLASH: 16MB SPI-NOR
WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax
SERIAL: 115200 8N1
LEDs - (3V3 - GND - RX - TX) - ETH ports
Installation
------------
Flashing is only possible via a serial connection using the sysupgrade
image; the factory image must be signed. You can flash the sysupgrade
image directly through the U-Boot console, or preferably, by booting the
initramfs image and flashing with the sysupgrade command. Follow these
steps for sysupgrade flashing:
1. Establish a UART serial connection.
2. Set up a TFTP server at 192.168.0.2 and copy the initramfs image
there.
3. Power on the device and press any key to interrupt normal boot.
4. Load the initramfs image using tftpboot.
5. Boot with bootm.
6. If you haven't done so already, back up all stock mtd partitions.
7. Copy the sysupgrade image to the router.
8. Flash OpenWrt through either LuCI or the sysupgrade command. Remember
not to attempt saving settings.
Revert to stock firmware
------------------------
Flash stock firmware via OEM web-recovery mode. If you don't have access
to the stock firmware image, you will need to restore the firmware
partition backed up earlier.
Web-Recovery
------------
The router supports an HTTP recovery mode:
1. Turn off the router.
2. Press the reset button and power on the device.
3. When all LEDs start flashing, release reset and quickly press it
again.
The interface is reachable at 192.168.0.1 and supports installation of
the OEM factory image. Note that flashing OpenWrt this way is not
possible, as mentioned above.
Signed-off-by: Darlan Pedro de Campos <darlanpedro@gmail.com>
(cherry picked from commit 2a0c9cc8cd)
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MediaTek MT7603E, MediaTek MT7613BE
- Switch: 1 WAN, 4 LAN (Gigabit)
- Buttons: Reset, WPS
- LEDs: System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS
- Power: DC 12V 1A tip positive
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Cudy WR1300 v3 differs from v2 only in swapped WiFi chip PCIe slots. Common
nodes are extracted to .dtsi and new v2 and v3 dts are created.
Cudy WR1300 v2 dts now contains ieee80211-freq-limit.
The same manufacturer's built OpenWRT image is provided for both v2 and v3
devices as a step in installing, but for proper WiFi functionality,
a separate build is required.
Recovery:
- Loads only signed manufacture firmware due to bootloader RSA verification
- serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
- connect to any lan ethernet port
- power on the device while holding the reset button
- wait at least 8 seconds before releasing reset button for image to
download
- See http://www.cudytech.com/newsinfo/547425.html
Backported from branch main to 23.05.
Signed-off-by: Filip Milivojevic <zekica@gmail.com>
(cherry picked from commit 288738c59d)
This fixes the following compile problem:
````
CC arch/mips/kernel/vpe-mt.o
arch/mips/kernel/vpe-mt.c: In function 'vpe_run':
arch/mips/kernel/vpe-mt.c:32:23: error: unused variable 'physical_memsize' [-Werror=unused-variable]
32 | unsigned long physical_memsize = 0L;
| ^~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[6]: *** [scripts/Makefile.build:289: arch/mips/kernel/vpe-mt.o] Error 1
````
physical_memsize was removed from upstream kernel, see:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.15.y&id=5b4f6c5ff65c8551018ccea40c569afd759734c0
Fixes: 387fde0da0 ("kernel: bump 5.15 to 5.15.150")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9cfa5f7417)
dsmark support was removed in kernel 5.15.150 and 6.1.80. Remove it from
the kmod package as well
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit bd6b37f463)
MT7981B /256MB /16MB SPI (XM25QH128C)
AX 2.4Ghz
AX 5Ghz 160Mhz wide
1Gbit LAN
OEM:
root@RE3000:~# ifconfig |grep HWaddr
br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0 (label)
br-wan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
ra0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
ra2 Link encap:Ethernet HWaddr 82:XX:XX:28:XX:X0
rax0 Link encap:Ethernet HWaddr 82:XX:XX:38:XX:X0
rax2 Link encap:Ethernet HWaddr 82:XX:XX:58:XX:X0
OpenWrt
root@OpenWrt:/# ifconfig |grep HW
br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
phy0-ap0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
phy1-ap0 Link encap:Ethernet HWaddr 82:XX:XX:08:XX:X1
tftp Installation via u-boot:
Connect TTL3.3V converter
connector is under the radiator Set speed 115200 8 N 1
Interrupt boot process by holding down-arrow key during boot then
>> 6. Load image
>> 0 - TFTP client (Default)
enter IP adresses and initramfs-kernel.bin
write to flash via sysupgrade or gui
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
(cherry picked from commit e8f7597317)
It was announced [1] that the original staging repositories are no longer
used for staging of new firmware binaries. And that the old repository will
be removed [2] in June 2024.
The ath11k-firmware package must therefore point to the new repository
before the old one is no longer accessible.
[1] https://lore.kernel.org/r/bac97f31-4a70-4c4c-8179-4ede0b32f869@quicinc.com
[2] 8d2cc160f3
Signed-off-by: Sven Eckelmann <sven@narfation.org>
802.11r can not be used when selecting WPA. It needs at least WPA2.
This is because 802.11r advertises FT support in-part through the
Authentication and Key Management (AKM) suites in the Robust
Security Network (RSN) Information Element, which was included in
the 802.11i amendment and WPA2 certification program.
Pre-standard WPA did not include the RSN IE, but the WPA IE.
This IE can not advertise the AKM suite for FT.
Signed-off-by: Jesus Fernandez Manzano <jesus.manzano@galgus.ai>
(cherry picked from commit cdc4c55175)
When using WPA3-SAE or WPA2/WPA3 Personal Mixed, we can not use
ft_psk_generate_local because it will break FT for SAE. Instead
use the r0kh and r1kh configuration approach.
Signed-off-by: Jesus Fernandez Manzano <jesus.manzano@galgus.ai>
(cherry picked from commit e2f6bfb833)
Fixes: https://github.com/openwrt/luci/issues/6930
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The dependency can't be satisfied when building using the SDK, breaking
package builds. As the staging and bin dirs are distributed with the SDK
archive, ignoring the dependency is fine when SDK is set.
Fixes: fbb924abff ("build: add $(STAGING_DIR) and $(BIN_DIR) ...")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 2b46cbef81)
In a pristine build, these directories are created as dependencies of
the tools subdir compile, however this step never runs when the tools
compile stamp already exists. Since commit ed6ba2801c ("tools: keep
stamp file in $(STAGING_DIR_HOST)"), this will happen after `make clean`:
$(STAGING_DIR) has been deleted, but the tools stamp still exists, so
the next build will fail because $(STAGING_DIR) has not been set up
correctly.
Fix builds after `make clean` by adding the preparation as dependencies
for the target and package directories as well.
Fixes: ed6ba2801c ("tools: keep stamp file in $(STAGING_DIR_HOST)")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit fbb924abff)
